Search Documents

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

5.1 TECHNOLOGY FOR INJECTING GROUT INTO BOREHOLES The grouting of fractured rock aquifers is carried out in separate stopes' whose size is determined by the hydro¬stratigraphy and the hydrogeologic properties of the rocks. The number of grouting stopes required depends on the number of intervals in the hydrogeological section. Each grouting stope can include one or several aquifers. Com¬bining several water-producing strata into one stope is pos¬sible only when the values of their permeability coefficients are very similar. In order to achieve efficiency, as many aquifers as possible are included in each stope. In practice, the length of a grouting stope in a borehole usually ranges within 10 to 40 m, but occasionally up to 100 m or more. When conducting grouting operations through boreholes drilled from the face of underground workings, the stope's size can be determined by the thick¬ness of each fractured zone (fault) or by the length of the hole if the entire rock is fractured. Injecting grout into separate intervals of fractured rock can be done from the bottom to the top with ascending stopes or from the top to the bottom with descending stopes. Injection from bottom to top is always preferred. Injection also can be accomplished in separate fractured permeable horizons in the section. The STG integrated grouting method is based on the use of packer and injection equipment and technological schemes that facilitate injection in highly isolated fractured aquifers. For this purpose STG has developed a standard series of packers. 5.1.1 INJECTING GROUT THROUGH BOREHOLES DRILLED FROM THE SURFACE Grout can be injected according to one of four techno¬logical schemes depending on the depth of the fractured aquifers, their hydrogeologic properties and the availability of grout injection equipment if the area is remote (Fig. 43). In the first and most preferred technological scheme (1), the grout is injected from the bottom up with ascending stopes. When this scheme is employed, grouting holes are drilled to the entire projected depth based on the field investigations injection tubes is installed above the top of the first hydrostratigraphic unit to be grouted. This scheme al¬lows the grout to be injected only into the permeable stra¬tum or strata isolated by the packer near the bottom of the hole; it precludes the need to clean or redrill the hole before injecting grout into the next overlying stope. This ascending stope scheme is preferred because of its simplicity and ef¬ficiency. It is used in most of the grouting of saturated fractured rock for the purpose of isolating aquifers while excavating deep mine shafts in the USSR. The second technological scheme (II in Fig. 43) injects the grout in sequence from top to bottom with descending stopes. Injection under this scheme is accomplished through the hermetically-sealed mouth of the hole. It is most advis¬able to grout with descending stopes in saturated fractured rock wherein the aquifers constitute thick networks of frac¬tures. Under these conditions it is practically impossible to drill a grout hole to the entire depth of the underground workings due to the large production rate of ground water. In conducting isolation operations with descending stopes, additional work (relative to ascending stopes) is necessary to drill out the grout in order to create and inject the next stope. As a result, the total amount of drilling required to drill out grout can even exceed the volume of drilling of original rock. Consequently it is advisable to use this inefficient scheme only for injecting grout into holes that contain prolific frac¬tured aquifers at depths less than 150 to 200 m. The third and fourth technological schemes (III and IV in Fig. 43) are used in the selective grouting of separate aquifers. For example, these methods would be applied when a grout hole is drilled to its entire depth, wherein grouting of the upper aquifers must be done first so that the sinking of the first shaft can begin prior to deeper grouting. The third technological scheme is used for the selective injection of grout into an aquifer with a thickness of up to 5 m. For this work the DAU-1-2 removable dual packer is installed. It is lowered into the borehole on an injection pipeline. For aquifers with thicknesses of more then 5 m, the selective injection of the grout is carried out according to the fourth technological scheme; a combination of the DAU-2 hydrodynamic plug and the DAU-1 packing device is used. In order to implement this injection scheme, the DAU-2 hydro-dynamic plug is installed at the bottom of the fractured aquifer and the DAU-1 packer is installed at the top of the aquifer.

Jan 1, 1993

The investigations described in this paper aim at the development of a new impact mill. The objective is to produce particle size distributions below 10 .tm without using an air classifier. Circumferential rotor speeds of up to 200 m/s are strived for.

Jan 1, 1993

By Raymond PoIick

The Demag Electric Slag Cleaning Furnace installed at the Asarco Smelter in Hayden Arizona is one of the few rectangular electric furnaces now operating. The long transition times from charge to tap allow exceptionally clean skims (high recovery); however, the furnace design is complex. Additional Asarco requirements for rapid installation and commissioning further complicated the design. When operating and wear effects accumulated after two years of use, steps were taken to rebuild the furnace with enhanced durability based on the design parameters experience in actual use.

Jan 1, 1993

[ ]

Jan 1, 1993

By A. F. Barsotti

Apart from jewelry, holistic apparel, and special collections of color and sometimes rare crystal specimens, the average layperson has little or no appreciation of the omnipresence of minerals or mineral derived products in the home. From concrete in the driveway to aspirins in the medicine cabinet, minerals, especially industrial minerals, play a major role in day to day living. For a better appreciation of this let's look into the a day of the life of a fellow named John, and see how much we depend on industrial minerals. The sounds of soft violins nudged John from his sleep. The melodic sounds of Beethoven's Pastoral coming from his radio alarm clock brought him out of his dreams. He reached for the reading light switch, then checked his watch--6:30 a.m., and another day of work. As he got up, the darkness outside reminding him of winter coincided with the soft voice of the all night disk jockey forecasting the fall of four inches of snow. Warm beads of water beating on his face removed all remnants of sleep and, like a stimulant, the morning shower brought thoughts of yesterday and plans for a new day. These carried over as he looked himself in the mirror while shaving and brushing his teeth.

Jan 1, 1993

By Jim A. King

The total pressure oxidation of copper concentrates is a potentially viable option for treating copper concentrates that are either low grade or contain significant impurities. Both concentrate types are heavily penalized in smelter contracts. The total pressure oxidation process involves autoclaving the copper concentrate at temperatures of 200-220 C under oxygen pressure. The autoclave discharge can be separated into a solid (oxidation residue) and a liquid (oxidation solution) product. The oxidation solution can be treated for copper recovery by solvent extraction - electrowinning or by direct electrowinning. The direct electrowinning recovery of copper requires prior removal of selenium and tellurium by cementation on finely divided scrap copper. The oxidation residue is washed thoroughly to remove acid and dissolved copper prior to precious metals recovery by conventional cyanidation in the presence of lime. The results of a benchscale investigation involving a number of copper concentrates are reported. Copper recoveries in autoclave oxidation and gold recoveries by cyanidation of the oxidation residue exceeded 99%. The results of benchscale experiments to demonstrate copper recovery are described. Various flowsheet options are presented.

Jan 1, 1993

By S. N. Rossovsky

"A new method for the hydrometalfurgical treatment of refractory gold arsenosulphide concentrates is presented. Themethod involves a combination of' finegrinding, intensive agitation, flotation, and cyanidation, and consists of leaching of -10u pyrite and arsenopyrite particles in alkaline solution under intensive agitation without the application of costly high-pressure and roasting techniques. Consistent extractions of gold, in excess of 96%, are achieved.IntroductionConventional methods of alkaline leaching of gold arsenosulphide concentrates in an autoclave» and under electrochemical oxidation( 2) require expensive equipment as well as high-cost energy and reagents. In other cases, processing of gold concentrates inelude: ultra-fme grinding, calcination at 200°C to 250°C with the addition of an oxidant (NH4NOJ followed by alkaline leaching of the resulting calcine with hydrogen peroxide, the latter being a complicated method yielding poor extractions of gold (89% to 90%). In this paper, a hydrometallurgical method is described for processing refractory gold arsenosulphide concentrates in which alkaline leaching is followed by cyanidation of the residue."

Jan 1, 1993

By Khosia NK, Ravishankar SA, Sankar TAP

Alumina reduction in Rajhara iron ore slimes essentially involves separation of hematite from gibbsite in relatively coarser fraction and from kaolinite in the finer fraction. Selective dispersion flocculation studies on synthetic mixtures clearly indicated that while it was possible to achieve almost perfect separation of hematite from kaolinite using starch and PAMX (modified polyacrylamide containing hydroxamate functional groups) flocculants, no selectivity was observed in iron oxide-alumina system. A schematic flowsheet suggested on the basis of this work for the beneficiation of Indian ore slimes thus consists of classification in a hydrocyclone, followed by selective dispersion of coarse fraction (underflow) and selective flocculation of the overflow fraction. Starting with a feed assaying 46 per cent Fe and 11.6 per cent A1203, a concentrate assaying 60 per cent Fe and 4.7 per cent A1203 could be produced at an overall iron recovery of 60 per cent using conventional Reagents.

Jan 1, 1993

By John J. Moore

This paper discusses the application of a video technique to construct stability diagrams for the combustion synthesis of ceramic-metal composites. Several model exothermic combustion synthesis reactions have been used to investigate the effect of the reaction parameters, eg. stoichiometry, green density, etc, on the stability of the propagating combustion reaction front and subsequent product morphology. The effect of varying the reactants and their stoichiometry to provide a range of reactant and product species ie. solids, liquids and gases, in the synthesis of both dense and expanded (foamed) ceramic and ceramic-metal composites was also investigated with respect to their corresponding combustion front stabilities.

Jan 1, 1993

By D. D. Murphy

The Bureau of Mines has studied the mechanism of shear-flocculation of silica with stearic acid. At pH 6 and 12, shear-flocculation of silica was not observed with up to 10-4M (5 lb/st) stearic acid. However, in the presence of 0.1 M NaCl at pH 6, shear-flocculation was observed at stearic acid concentrations 10-4 M (5 lb/st). Adsorption of stearic acid on silica was studied using stearic acids spin-labelled with a doxyl group. The presence of the spin-labelling group did not greatly affect the shear-flocculation properties of stearic acid. Adsorption of labelled stearic acid on silica was measured as a function of surfactant concentration with electron paramagnetic resonance (EPR) spectroscopy and gas chromatography (GC). The GC results indicate the stearic acid was predominately adsorbed on the surface at concentrations above 10-4 M. From the EPR spectra, the formation of aggregates of stearic acid was apparent at concentrations of approximately 10-414 (5 lb/st). The results are discussed in terms of a possible mechanism for shear-flocculation.

Jan 1, 1993

By D. W. Mitchell

Never increase, reduce, or remove ventilation without unquestionable, compelling reasons. This rule applies every day as well as when fighting fire, attempting to find survivors, or recovering the mine. Right now in some mine a miner is adjusting a regulator in one place to get more air into another. The chances are the desired result will be achieved. Has the miner done a good thing? NO! Solving the immediate problem reinforces the belief he or she can do it again. That "again" might be, to give but one of many examples, the explosion in Greenwich No. 1 Mine. Robbing the proverbial Peter can be the prelude to disaster in a mine. Reducing the airflow is a common practice when fighting a mine fire. In fact, some people have been taught to do that at MSHA's academy. People who believe that to be proper must be people who never experienced a fire. To fight most fires you have to scramble to get enough air. An explosion demands totally different "thinking". If people are soon to go into the mine, DON'T adjust the ventilation. If teams are in the mine, each affected area must be explored or sealed before making any ventilation change.

Jan 1, 1993

By Sheila Luchansky, F M. Babcock, Daniel M. Sanders

A cooperative effort between a blasting vibration consultant, a blasting contractor, and personnel from the City of Las Vegas has dramatically reduced complaints from residential areas near developmental blasting projects. The principal methods used involved the preparation of an informative video recording which presents various aspects of the blasting operations, the design of a distinctive flyer which is attached to residential doors, and pre-blast meetings for information dissemination.

Jan 1, 1993

By Gunter Swoboda, Harald Wagner

Until a few years ago tunnel construction was based exclusively on experience. In recent years, however, numerical models have increasingly become an integrated part of tunnel design [2]. These models permit good evaluation of the tunnel's support behavior even before it is designed. In particular, numerical methods are highly suited for the development of new construction methods. The prerequisite for this is the application of high-performance pre- and postprocessors, permitting the design engineer to come to a quick interpretation of the analysis results. In future, 3D analysis will take on increasing significance, for which reason this paper also deals with this type of models.

Jan 1, 1993

By R. A. Winters

At the operations level, productivity is a principle key to profitability. If you are competing with other mines that are paying roughly the same wage rate and the same prices for capital, materials, and energy, the only way your profit can be greater is by producing more output per unit of input. Mines with higher productivity have higher profit margins. Higher profit margins lead to greater operating cash flow, and cash flow is what distinguishes a dog from a cash cow. The turnaround in U.S. metals during the 1980s was in large part due to incredible improvements in productivity. According to statistics compiled by Kaufmann, 1991, labor productivity, measured as tonnes of primary production/manhour, increased 64% in steel, 94% in copper, 75% in lead, 143% in zinc, 132% in molybdenum, and 75% in gold. These improvements were hard won. However, with most modernization programs now complete, measuring and monitoring productivity becomes even more important as producers strive to maintain the gains they have achieved.

Jan 1, 1993

By J. J. Bartels

The phosphate rock review did not arrive in time for publication in the. June issue. The world phosphate industry continued its slide in 1992 from the already depressed levels in 1991. The industry is locked into a 30-year fertilizer price low due to the worldwide fertilizer glut. Domestic production and imported, marketable phosphate rock decreased 1%, while domestic consumption increased by 1 % last year. The US Bureau of Mines reported a decrease in the domestic phosphate rock value from $25.42/t in 1991 to $23/t in 1992 ($23.06/st to $20.80/st). The diammonion phosphate (DAP) product price also dropped in value from $138/ t in January 1992 to $11 0/t in December ($125/st to $99.70/st). Continued declines in DAP prices is forcing the US fertilizer industry to develop cost-saving programs and reorganizations. Layoffs in 1992 resulted in a 7.6% decrease in the Florida phosphate workforce. Since 1980, the Florida workforce has declined by 35%. Small phosphate companies were forced to close operations or were sold to larger phosphate companies. Federal and state environmental regulations for byproduct waste disposal methods are being studied. The Environmental Protection Agency (EPA) approved phosphogypsum use in agri¬cultural and research applications as long as the radium 226 concentration is lower than 10 pci/g. The EPA is also reviewing regulations concerning air emissions at fertilizer plants. Industry publications reported the possibility of continued company sales and mergers in 1993. Industry expectations are optimistic while waiting for an upturn in the market. The US phosphate industry consolidation into three or four major companies should evolve into a stronger world market force.

Jan 1, 1993

By L. P. James

The Bulagidun copper-gold system occurs in Tertiary andesitic volcanic rocks. It is located (figure 1, from Curless, 1991) ca. two days walk from the coast in an isolated area on the northerly slope of the main range of mountains, in steep terrain dissected by erosion. Detailed and district-scale exploration from 1988 to 1991 by BHP Minerals defined a small, sub-economic resource of gold and copper. One preliminary estimate of the resource in bedrock suggests 14.4 million tons at 0.68 grams / Tonne Au and 0.61% Cu, in multiple small bodies.

Jan 1, 1993

By Charles L. Kimbell

While the statistical summary focuses on 1991 data, this update and outlook section draws on information available to the author as of the date of final preparation in early 1993. For all the press notoriety associated with the shift in the Near East crisis from the defensive posture of Desert Shield to the restoration of Kuwaiti sovereignty through Desert Storm, this was not the dominant event governing global economic thinking in 1991 and the first half and more of 1992. From the global perspective, the momentous political changes in the area that was the U.S.S.R. and in the smaller emerging transitional economy states of Eastern Europe will have even greater current and long-lasting effects on world mineral industry activities than the crisis in the Near East.

Jan 1, 1993

By Plamer D. J, Newman O. M G

The Effluent Treatment System at Pasminco Metals - EZ (PMEZ) was commissioned in December, 1991 and has operated satisfactorily, ensuring that aqueous discharges from PMEZ comply with the Tasmanian Environment Protection Act. The system treats both spills and run-off from the Zinc Plant, and acidic liquor generated in the gas cleaning section of the Sulphuric Acid Plant. The spills and run-off from the Zinc Plant are collected in a large catchment pond. The pond liquor, after partial neutralisation with sodium hydroxide to pH 4, and removal of suspended solids, is preferentially recycled to the Zinc Plant, for example, for washing of residues. Liquor which cannot be recycled, is treated in the Lime Neutralisation Section. The other input to the Lime Neutralisation Section is the acidic liquor from the Sulphuric Acid Plant from which mercury has been removed by contact with aluminium pellets in a fluidised column. In the Lime Neutralisation Section, the liquors are blended and neutralised to pH 10 by the addition of slaked lime. The heavy metals and most of the fluorine are precipitated. The precipitated solids are removed in a thickener with part of the thickener underflow being filtered. Most of the thickener underflow is recycled to generate solids that settle rapidly and filter well. The filter cake is returned to the Zinc Plant for the recovery of contained heavy metals while the thickener overflow is discharged to the Derwent River.

Jan 1, 1993

By M. C. Williams, T. P. Meloy

With the increasing power of computers to simulate and control processes in the mineral industry, predicting the potential use of computers in the minerals field is not a hazardous enterprise, but predicting the timing of their use is. Like the railroad industry, technology invades the mineral industry, rather than being an industry like electronics that creates technology. Because of this invasive nature of computer technology in the minerals field, this paper predicts what will be possible to do effectively and economically with computers in the mineral industry. Moreover, this paper explores the problems of using the emerging computer technology in the mineral industry. For example, if not now, it soon will be possible to control the output of a mineral processing circuit - high grade, high flow or a mixture of it - to meet the daily market conditions and to sell each day that daily "mill" output as "mill" futures on the commodity market. Finally, suggestions are made which may be done to prepare the industry for the computer revolution in the mineral industry.

Jan 1, 1993

By Farrelly C. T

The Wiluna mining operations are centred near the township of Wiluna 750 kilometres north-east of Perth and 600 kilometres east of Geraldton.The Wiluna gold mines produced over two million ounces of gold, predominantly by roasting the refractory sulphide ores, before closing in 1947. In the period 1984 to 1992, 668 000 ounces of gold has been produced from free milling oxide ores and the retreatment of tailing. A plant capable of treating the refractory sulphide ores using the bacterial oxidation, Biox technique was commissioned in March, 1993.The Wiluna lode deposits are hosted by a sequence of very low grade metamorphosed mafic flows at the northern end of the Norseman-Wiluna greenstone belt. A strike slip fault system provided conduits for fluid migration; ore deposition occurred at favourable sites along the faults. Satellite mines at Gourdis and Wiluna South provide laterite and lode style oxide ores.The different styles of deposit and ore types at the Wiluna mining operations require a flexible approach to resource estimation and grade control practices.

Jan 1, 1993