Search Documents

By K. N. Han

The dissolution kinetics of cobalt in iodine/ iodide solutions were investigated using a rotating-disc technique. Variables studied included temperature, rotating speed, concentration of lixiviants and the pH of the solution. The overall dissolution reaction appeared to be limited by the mass transfer of tri-iodide through the diffusion boundary layer with an Arrhenius activation energy of <16.2 kJ/mol (4 kcal/mol) over the temperature range of 2 to 42ºC. The pH of the solution had little effect, as long as the pH of the solution was <8. However, when the pH of the solution became >8, the dissolution rate decreased dramatically, due to passivation. The rate of dissolution was in good agreement with the dissolution model developed by the authors earlier.

Jan 1, 1995

By Silvia H. M. Grimaldi, Afonso H. Martins

The scope of this experimental work was to study the yttrium extraction and stripping behaviour in a solvent extraction system with mono(2-ethylhexyl)2-ethylhexylphosphonic acid (IONQUEST 801) in a chloride system The study was performed for only one contact between organic and aqueous phases The experiments were carried out according to a factorial design. Due to the statistical analysis and its experimental proof, the optimum conditions for maximum yttrium loading into the organic phase of the extraction stage were 16 minutes for time of contact between phases, 980 rpm of stirring intensity and pH=2.3 for the aqueous phase of the sovent extraction system. The optimized experimental conditions by the statistical approach for the stripping stage were: time of contact between phases equal to 20 minutes, 1050 rpm of stirring intensity and 1.75 M HCI into the stripping aqueous solution.

Jan 1, 1995

By William D. Riley

The U. S. Bureau of Mines has developed technology to recover by-product materials from aluminum scrap using engineered scavenger compounds (ESC). ESCs are structural oxides with a channel or tunnel structure that allows them to hold ions of a specitksizes and charges. The scavenging reaction is easily reversible allowing the ESC to be recharged for continued use and the ion is recovered as an electro deposit. Key features of this novel technology are; a) ESC ,systems are designed to have a high degree of selectivity for a desired ionic species. b) The recovered mater.ial requires little or no additional reprocessing prior to reuse. Two current uses for the ESC technology that are described in this paper are the removal and recycle oflithium (Li) from lithium aluminum (Li-AL) alloys; and, using ESCs as a replacement for the conventional demaging (magnesium removal) technology used by the secondary casting industry. Research indicates that the ESC technology proposed for both these applications has either &apos;distinct economic and/or environmental advantages over previously employed methods of recovering. metal values from aluminum scrap.

Jan 1, 1995

By F. Gray

Diamond tool fabricators expect strong growth in most applications for 1995 and 1996. Overall growth projects range from 8% to 10%. Diamond grinding is forecast to grow between 5% and 8%, while cubic boron nitride grinding should grow between 10% and 12%. A strong automotive industry is a major factor in this projected growth, as is continuing demand for other durables

Jan 1, 1995

By Shelley M. Burg, Dennis K. Poulton, Robert B. Gordon

This project includes the excavation and concrete lining of approximately 18 900 m (62 000 ft) of 5.5 m (18 ft) finished diameter subway tunnel for the Los Angeles MTA. The project required that four soft ground headings be excavated from a single shaft located near the mid point of the tunnels. The tunnels were classified "gassy" during the excavation phase. Because of the contract schedule requirements and the limited urban work site available, many logistical problems had to be overcome during the project while excavation was accomplished at a record setting pace. Some unique project features include the muck handling system and an access shaft using a high strength tieback support system. In order to accomplish the work, an extensive effort to plan and construct the main work site was required.

Jan 1, 1995

By A. C. Hitchins, C. N. Orssich

The Eagle zone is a gold-bearing, sheeted, quartz vein porphyry deposit hosted by the Cretaceous Dublin Gulch biotite granodiorite stock, located in central Yukon, 50 km north of Mayo. The deposit occurs at the western end of the stock and has been drill tested over a 1000 m by 500 m area, to a depth of 150m. Mineralization consists of 1 cm to 2 Cm wide, parallel, grey and white quartz veins with accessory gold, arsenopyrite, pyrite, pyrrhotite, chalcopyrite, native bismuth, bismuthinite, and scheelite. Vein densities range from two to fifteen veins per metre and average approximately five per metre. The majority of the veins have potassic and or phyllic alteration envelopes. Alteration of the granodiorite becomes pervasive as vein densities increase. Mineralization outside of the Eagle zone, but spatially related to the Dublin Gulch stock, includes: (i) scheelite bearing sheeted quartz vein zones within the east-central portion of the stock; (ii) a swarm of gold-bearing quartz-sulphide veins up to a metre wide in a zone along the northern contact of the stock and extending 7 km further west; (iii) the Mar scheelite skarn located on the south side of the stock; and (iv) cassiterite-bearing breccias located 2 km north of the stock. A geological potential resource of 64.5 Mt tonnes at a grade of 1.03 g/t Au has been estimated for the Eagle zone from widely spaced core and reverse circulation drill holes. Mineralization is open at depth, on strike to the west and beneath the hornfels to the north.

Jan 1, 1995

By S. Kmet, A. Nguyen-Van, H. J. Schulze

The P/B collision and attachment interactions in fine particle flotation have been quantitatively analyzed. New models for attachment probability and kinetics of ‘true flotation’ have been developed. The results are given for both a single bubble and a bubble swarm. The mechanism of the attachment event is also examined. It is shown that (i) impact collision mechanism and rolling mechanism can be ignored in actual fine particle flotation and sliding mechanism is of importance for attachment of particle onto the bubble surface (ii) the attachment probability of fine particles is independent of bubble size and determined by the kinetic measure induction time of hydrophobicity. The theoretical predictions are also compared with the experimental data.

Jan 1, 1995

By G J. Corbett

Magmatic-related low sulfidation hydrothermal ore systems at plate margins exhibit distinct spatial and temporal zonations which can be used to aid mineral exploration and development. Low sulphidation systems at all crustal levels exhibit the same paragenetic sequence of events: early breccia formation, followed by quartz - secondary feldspar sericite/illite veining, then mineralisation, and final argillic overprint. This sequence of events is interpreted to reflect the initial emplacement of melts at high crustal levels, and the progressive cooling of that melt and release of magmatic constituents into a circulating hydrothermal system. &nbsp; Low sulphidation systems in the south-west Pacific region exhibit a vertical zonation in deposit types: from porphyry copper-gold at deep levels, quartz-sulfide-gold at mesothermal to deep epithermal levels, carbonate-base metal gold at mainly epithermal levels, and epithermal quartz silver-gold at shallow levels. It is interpreted that the characteristics of each of these styles of deposits is produced by mixing with circulating waters of different physio-chemical compositions.

Jan 1, 1995

By Ching Wu, David A. Sutter, Peter Frobenius

The MUNI Metro Turnback (MMT) Project includes a 256 m (840 ft) twin tunnel section, which connects to the Embarcadero Station, and runs under Market Street in San Francisco. The tunnels go through a mixed face condition of fill at top and Bay Mud at bottom, and a significant number of buried timber piles. This paper presents the selection of tunneling equipment, excavation methods, excavation support and chemical grouting; specification of timber pile cutting methods; and steel lining analysis and design. This paper also reports on the initial phase of the tunnel construction.

Jan 1, 1995

By Brent A. D, Olsen a. H, Mayfield P. L J, Grazier P. E

Concentrates produced from MnO2 and Fe203 ore fines have been targeted as potential feedstocks for direct metallurgical processing. Prereduction of pyrolusite-rich Mn02 sands to MnO has been investigated in batch and continuous experimental bubbling fluidised beds using CO-H2 reducing gas mixtures. This process has been found to produce a high grade feedstock suitable for smelting to ferroalloys or acid digestion for chemicals production. Similarly, production of highly metallised direct reduced iron (DRI) from hematite ore fines has also been investigated in batch bubbling bed reactors. Programs to characterise the reduction kinetics, fluidisation behaviour and defluidisation phenomena for both feedstocks are currently in progress to enable optimum process conditions to be determined.

Jan 1, 1995

By G. D. Hood, B. E. Davis

A fundamental study of the mechanisms involved in the conditioning of coarse Florida phosphate has led to some interesting discoveries. Studies by the US Bureau of Mines have shown that conditioning time and mixing intensity greatly affect the grades and recoveries of the phosphate minerals and quartz in the rougher concentrate. In particular, as the conditioning time or mixing intensity increased, the phosphate recovery remained constant while the amount of quartz floated decreased. This phenomenon is contrary to conventional wisdom and could lead to a more efficient coarse flotation circuit.

Jan 1, 1995

By Bhattacharyya A. K

In this paper, the current methods for predicting surface subsidence due to underground coal mining are evaluated first. A single index, called a strata parameter (P), is then proposed to describe the overall character of the undermined strata in the context of surface subsidence. Based on the strata parameter, a method for predicting the maximum surface subsidence for various panel width (w)/depth (h) ratios is presented, which has been tested against specific empirical curves or data from several coalfields in different countries. From the data relating to several coalfields, a linear relationship between the reported average angle of draw and the strata parameter has been established. It has also been found that the strata parameter can be used for studying the locations of the inflection points and the shapes of transverse subsidence profiles.

Jan 1, 1995

By Hainsworth D, Winstanley G, Gurgenci H, Corke P

Past experience has shown that the automation of the dragline swing motion requires real time monitoring of the bucket position. A current project at the Centre for Mining Technology and Equipment (CMTE) is aiming to achieve this using machine vision. The hardware platform is a Datacube MaxVideo 200 system. The images are obtained by a fixed camera installed on the dragline boom. The field of view is large enough to include the bucket in all possible configurations. Standard chain coding and run-length coding algorithms are used to process the video image. The three-dimensional bucket position is calculated by combining the output of the machine vision system with the rope length data obtained from transducers installed on drag and hoist drums. This information is then fed into a control computer which takes corrective action to suppress bucket oscillations before they reach dangerous levels.

Jan 1, 1995

Numerical simulation of the fluid flow and heat transfer has been carried out for a waste-heat boiler in an Outokumpu type copper flash smelter. In this boiler, SO2-containing off-gas flows into the waste-heat boiler radiation section at about 1350°C. A fraction of cooler off-gas from the electrostatic precipitator at about 200°C was recirculated into the radiation section, and a small amount of ambient air was leaked into the boiler from the bottom. The computational results show that the flow is strongly recirculating and distinctly three dimensional in most of the boiler, particularly in the radiation section. The hot off-gas cooled down rapidly after entering the radiation section due to radiation. The predicted flow pattern and temperature distribution were in a good agreement with laboratory models and industrial measurements.

Jan 1, 1995

By N. Piret, B. Shoukry, S. Buntenbach

Traditional or artisanal goldmining, also known as small scale goldmining, has a strong and probably a negative environmental impact. The processing methods applied are very frequently a source of severe pollution due to the emissions of mercury by the extraction of gold by means of amalgamation as well as the emissions of cyanide through cyanide leaching of gold bearing ores. The emissions find their way into the environment and contaminate soils, sediments, water and atmosphere. Abnormal concentrations of mercury and cyanides in waterways are known to occur year after year destroying irreplaceable regions of the world. Mercury and cyanide compounds are highly toxic and may directly create permanent damage to the whole ecosystem. Existing methods for recycling of mercury and for decontamination of mercury and cyanide contaminated tailings are not customary applied in small scale mining and are ineffective as well. Based on investigations of traditional and small size goldmining, this paper presents: -processing methods of gold and discarded tailings under consideration of environmental protection; -figures on actual situation; -recommendations for equipment; -some decontamination methods for mercury and residual cyanide. Mineral Processing methods in traditional gold mining Gold is usually existing in its ores as the metal alloyed with metallic silver and perhaps copper. The element may occur in the form of: -native gold -inclusions also of microns or submicroscopic size metal sulfides (auriferous) such as pyrite, pyrrhotite, stibnite, arsenopyrite and galena -combined as telluride or sulphotelluride. The separation process selected depends on whether the gold can be freed from its unfavorable associations (e.g. gangue) at a sufficiently coarse grain-size, or whether it is carried in a heavy sulfide which can be freed similarly. The usual practice is to concentrate the goldbearing mineral at a relatively coarse grain-size and to regrind the ore if necessary. The gold content is concentrated by secondary or tertiary gravital methods or is extracted by chemical methods (amalgamation, cyanidation etc.) Gold, even when of fine grain-size, settle readily due to its high specific gravity from pulps in which the main gangue mineral is quartz or silicates. Amalgamation is the process of separating gold and silver from their associated minerals by binding (entrapping) them into a mixture with mercury. The cyanide process is applied to separate gold or gold-bearing compounds by dissolution from the finely ground ore (CIP, CIL, RIP), or as heap leaching. The dissolved gold is separated from the solids and the metal-rich or pregnant solution is then treated to recover its gold. Gold is also recovered by flotation methods. This process is widely used in treating base metal ores and in separating various sulfide components of ores, as well as in removing the barren gangue. The gold usually associates with a specific product in a sequence of flotation operations and is recovered subsequently in the smelting of the sulfide concentrates and refining of the metallic products, or by cyanidation of the roasted concentrates. Froth-flotation can be applied to separate gold and sulfide minerals from a finely ground pulp. The Amalgamation Process Amalgamation is the main method for the recovery of gold in traditional mining and is applied for the extraction of gold from placers as well as primary ores. The mineral technology used depends on the nature of ore deposits. In winning gold from solid ore, the matrix of minerals and rocks must be crushed and ground to sufficient fineness to liberate the gold. The liberated gold could be treated similar as free gold from placers. Gold is mainly separated from the valueless gangue (barren rock) by utilizing the difference between the density of the impure native metal (density about 16-19) and the gangue (density about 2.5). In simple operations the material is carried by a stream of water down a sluice generally equipped with small transverse barriers (riffles) against which the gold collects. The riffled sluice is the principal device used by artisanal gold miners. Nowadays, spirals as well as centrifuges, such as Knelson separator or Falcon separator, are occasionally applied for gold recovery. Gold may also be recovered from the pulp, by passing it over corduroycovered tables that catch the heavier particles - a method maybe as ancient as gold mining itself. In history, sheep skins were used to catch gold particles in this manner. Furtheron, gravity separation of gold is practiced on jigs, hydraulic traps, shaking tables and

Jan 1, 1995

By Brian O'Hearn, Doug Hanson

"The most commonly used tendon supports in the Sudbury area include rock bolts, rebars, friction anchors and cable bolts. Due to the fact that these tendons are physically different and employ different anchoring systems they offer varying degrees of stiffness, yield ability, load capacity, anchor dependability and energy absorption. These differences coupled with variable rock mass and changing stress conditions have made it challenging to engineer the design of an effective support system. By tapping into the knowledge and experience gained by ground control practitioners, an empirically based rating system has been assembled that offers a guide to designers of support systems when choosing the most effective tendon support over a range of rock mass and stress conditions.A methodology referred to as support planning can be used to design support systems whose rehabilitation costs will be minimized. The use of multiple tendon types in anyone support layout is advocated, particularly when the stress state of the rock mass to be supported is expected to undergo a change."

Jan 1, 1995

By Daniel Hodouin, Claude Bazin, Sami Makni

A method is proposed to perform on-line data adjustment and inference of unmeasured variables, using measured flowrates and on-stream assays in mineral processing plants. The algorithm minimizes a weighted sum of squared residuals of the measured variables and squared species imbalances around the flowsheet nodes. The method is based on a trade-off between the material transient accumulation, evaluated by the imbalances, and the data inaccuracies, evaluated by the residuals (i.e. the adjustments brought to the measured values). A recursive algorithm is developed for on-line implementation of the method. It is a real-time extension of the hierarchical method for balancing steady-state data for bilinear mass conservation constraints. An illustration for a simulated flotation circuit is provided.

Jan 1, 1995

By Robert W. Baker

"Brunswick Mining and Smelting commenced production at the No. 12orebody, a lead/zinc/copper/silver deposit, situated some seventeen miles southwest of Bathurst, New Brunswick, in 1964 at 4100 tonnes per day. Today it operates at 10500 tonnes per day.Brunswick has utilized underground incentives since commencement of operations. Early incentive systems were “off the wall"" based on those in effect at other properties then manipulated to fit, often hack calculated from actual performances to tm1ve at the desired result. If subsequent payouts were considered too high the rates were simply reduced, often retroactively. A large amount of this was&apos; subjective and depended to a large extent on whoever was handling the bonus, in conjunction with senior mine department staff.In 1971, it was&apos; decided that a more scientific approach was needed, particularly with the introduction of the new cut-and-fill mining. After some research, a system based on Work Study was selected. Another major mining company employing such a system loaned one of their experienced employees to train some Brunswick personnel in the art of Work Study and conversion of data to incentive rates, and in 1972, the first such developed incentive rate was-introduced.Along the way, borrowing from others where necessary, a set of Brunswick principles and parameters were developed. While refined to some extent, these remain basically the same today.Improvements in methods and equipment have resulted in improved performance and reduced costs. The use of underground incentives has played an important role in this. A/though individual bonus earnings have steadily increased, bonus cost per tonne has remained nearly constant - in real dollars, it has regularly decreased. These are two of the main parameters of a successful system."

Jan 1, 1995

By K. N. Han

The adsorption of gold onto activated carbon in iodide solutions was studied. The adsorption rates were determined as a function of temperature, salt concentration and pH, as well as activated carbon concentration. A kinetic model was developed for the adsorption. The adsorption rate was believed to be controlled by a combined mechanism of film diffusion and pore diffusion with the film diffusion having the most significant effect. Experimental findings were in good agreement with the model developed. The apparent activation energy was found to be 14.9 kJ/mol.

Jan 1, 1995

The Pacific Rim countries ofAustralia, New Zealand, Papua New Guinea, Indonesia, Fiji, Philippines and Solomon Islands will be reviewed from an equity investors perspective. &nbsp; The following areas will be covered: Country risks Exploration spending and activity Project development Taxation Relative cost of doing business Environmental considerations Political/bureaucratic situations Capital raising Equity markets as a source of funds Developing market funds The aim of the paper will be to outline the most attractive areas for investment by equity and private funds plus documenting the changes needed in the less favourable countries if they are to attract investors.

Jan 1, 1995