Search Documents

By Ruschitzka C

The productivity and economic success of a German hard coal mine is attributed to the high productivity of a small number of operation points; however high rates of production are associated with increased gas emission at the working sites. Therefore modem high technology is required in order to reach the planned production rate, since high methane concentrations often cause unplanned breakdowns in operation. The optimised simulation of gas emission is a fundamental planning tool for mine design as well as for determining the potential of a coal deposit and has increased in significance over the last years. Methane-INFO enables the three-dimensional, graphical simulation of a working site taking account of different aspects such as the mine design, ventilation, production rate, geology, seam quality, gas exhaustion, etc. The following paper gives a short overview over the benefits of the discussed system.

Jan 1, 1995

By Bradley V. Nelson

A number of improvements in the ventilation system at the Henderson Mine have been made during the past several years. A key to these improvements was the installation of a computerized monitoring and control system. Employees can determine the status of any of hundreds of devices in seconds through the use of this monitoring system. Mine dewatering pumps, the water treatment system, the ore haulage system, electric power usage as well as other devices are controlled and/or monitored. Ventilation parameters which are monitored include air flow volumes and carbon monoxide as well as the status of main surface fans, mine doors, and ventilation raise doors. Main underground fans are also constantly monitored and can be controlled remotely. These underground fans can be programmed to automatically start and stop to follow work schedules, optimizing air quality while reducing power cost. Mine air heating costs have been reduced by replacing an electrical resistance heating system with a direct fired natural gas heating system at the portal of the ore haulage tunnel.

Jan 1, 1995

By W. K. Tolley

The U.S. Bureau of Mines (USBM) is currently investigating improved technology for mineral flotation. A variable often neglected in flotation control is redox potential. The use of redox control is illustrated by the separation of molybdenite from chalcopyrite. Laboratory testing showed that redox potential had a greater effect on product quality than collector addition. A significant need in froth flotation is greater reliability of the sensors used in measuring and controlling redox potential in mineral slurries. The USBM has developed an automated method for removing scale and reconditioning gold redox-sensing electrodes. Fouled electrodes are anodically polarized to 1.2 V versus the AglAgCI reference potential to remove scale. The electrodes then are conditioned by a brief potentiodynamic treatment to re-establish electrochemical equilibrium. In laboratory tests, this technique removed calcarious deposits from gold electrodes and reconditioned them for useful service in approximately 10 min. In plant practice, this technique would obviate the need for plant operators to manually polish electrodes, and also should result in greater reliability in redox measurements. Inexpensive, automated equipment to condition electrodes in a plant setting is described.

Jan 1, 1995

By Mauk JL, Arehart GB, Mathews SJ

The banded nature of the quartz veins which form the Empire lode at the Golden Cross mine, is perhaps their most striking feature. Petrographic studies show that significant differences occur between the bands in terms of textures, quartz grain size, calcite, adularia and kaolinite content, and the form, concentration and mineralogy of sulfide phases. The 818Oqu i values of individual bands within the vein material range from 7.3-10.9%x. Calculations show that the 818Oqäa,u values can be adequately explained by temporal variations in the system temperature, boiling and/or variations in the systems fluid/rock ratios.

Jan 1, 1995

By Sandvik

Fine grinding in an air-swept ball mill working in closed circuit with a forced vortex air classifier has been investigated first in continuous laboratory and then in industrial scale. Results from the laboratory circuit have shown significant influence of mill load (powder filling) on the capacity of the circuit. In laboratory scale the mill load was measured and controlled by a weighing platform placed under the complete mill set-up. The mill load of the industrial air-swept ball mill has till now been controlled by measuring the power consumption of the mill motor. Thus, it was necessary to operate far from the range of optimal mill filling. To improve the circuit performance, alternative ways of mill load measurement were investigated. An important factor was investment cost, as many fine grinding mills operate in relatively small circuits that do not wan-ant large investment. In this case the task was accomplished by using a piezoelectric strain transducer, which detected strain changes in the mill shell. It was installed in the midpoint of the shell, where the highest deformation was obtained. As the transducer was on the top position, it indicated compression, and on the bottom position it measured tension. By taking the difference between the readings, it was possible to calculate total strain variations, directly proportional to the mill load. The signal from the transducer was sent to a control room via a cordless infrared communication system, employing a microprocessor control card, which could further regulate other operating parameters of the circuit according to the software model. The installation required very low investment cost and provided simplicity of application as well as stability and reliability of characteristics under severe industrial condition. The measurement system made it possible to optimise the mill load and thus increase the production from 3.2 to 3.7 dh (15 per cent), and stabilise the circuit operation.

Jan 1, 1995

By Heath E, van Calsteren P, Turner S, McDermott F

U-Th isotope studies of recent volcanic rocks may be used to evaluate the depths and rates of melt generation beneath mid- ocean ridges and ocean islands. Island arc rocks exhibit a similar range in Th isotopes to that seen in both MORB and OIB, but while those with high (230Th/232Th) tend to have excess 238U, many of those with low (230Th/232Th) are in isotope equilibrium. The excess 238U is attributed to the preferential mobilisation of U in hydrous fluids from the subducted slab within the last 100,000 years, whereas the low Th isotope ratios in the higher-K arcs are primarily due to the introduction of subducted sediment. Preliminary results from mineral separates from lavas on Soufriere on the island of St. Vincent indicate that some of the minerals crystallised up to 50,000 years prior to eruption.

Jan 1, 1995

By Lynn L. Rethi

This U.S. Bureau of Mines report summarizes common obstacles found when attempting to implement health and safety strategies in small mines and small businesses in general industry. Recently, the U.S. Mine Safety and Health Administration focused much of its attention on addressing health and safety issues at small mines. Some of the more innovative interventions practiced by small businesses in general industry are discussed for consideration of their applicability to the mining industry. The most effective intervention strategy that was developed for small businesses is the Occupational Safety and Health Administration Consultative Program. The details of this program and other intervention strategies used by small mines and small businesses are presented.

Jan 1, 1995

By Michael L. Sorokin

The behaviour of cobalt during processing of nickel raw material is analysed within the Ni-Co-Fe-S-O-SiO2 system using the computer model. For this purpose the thermodynamic parameters for "three-suffix" Margules's equations in Co-Fe-S and Co-Fe¬Ni-O-S1O2 systems were computed! Phase and iso-activity diagrams for Co-Fe-S system, and phase diagrams for the systems Co-O, Co-Fe-O, Co-Ni-O, C-oO=SiO2 and Co-Fe-O¬SiO2 are calculated using the developed computer programs and identified parameters. The diagrams are used to analyze cobalt behaviour at smelting and converting.

Jan 1, 1995

By Michael S. Robinson, Serge Moalli

Construction of the CSO Retention - Treatment Tunnel, Segment 1 in Dearborn, Michigan includes excavation for an overflow Structure with a minimum inside diameter of 15.24 m (finished). The excavation extends downward through overburden soil including a 15.2 m thick zone of potentially weak clay. This paper presents the subsurface data for the clay and a geotechnical analysis thereof, together with predictions of the behavior of the planned 15.54 m inside diameter open end caisson as it is sunk through this potentially weak zone. In a companion paper, the writers will compare the behavior observed with that predicted.

Jan 1, 1995

By T. J. White

Each year, thousands of tons of toxic concentrates are produced as the unwanted byproducts of industrial operations and smelting activities. The fate of these materials remains open, as in general their consumption is limited and potential markets contracting. Xtaltite (pronounced crystal-tight) is a Synthetic Mineral Immobilization Technology (SMITE) optimized for the concentration, detoxification and consolidation of toxic metal wastes. In this approach, we seek to mimic nature to produce durable synthetic minerals that survive for aeons in well characterized geological settings. This approach has high public acceptability because the concept is easily understood by the layperson and the long term stability of the waste form may be predicted with confidence. In addition, where Xtaltite is used for mine backfill, a system of ecologically sustainable mining development is established. This paper details the design and fabrication of Xtaltite under oxidizing and reducing conditions. To illustrate and contrast these stabilization regimes, specific reference will be made to the treatment of thallium, chrom~um and arsenic wastes. Waste form performance under TCLP, dynamic boiling water tests and in other leaching media will be compared and discussed with respect to their relevance to different disposal options.

Jan 1, 1995

By Jianmin Qin, Raja V. Ramani

In this paper, the results of a research study on airborne dust transport in a full scale simulated longwall face are presented. The simulated longwall face was set up in the Lake Lynn Laboratory mine of the U.S. Bureau of Mines to conduct experiments under controlled conditions. The controlled parameters in the experiments were the dust dispersion rate, dust size distribution, density of the dust, air velocity, and the rate of travel of the dust generating source. The analyses of the experimental results on mass concentrations, particle size distributions, and real-time respirable dust concentrations are discussed. There are definite spatio-temporal trends between the location of the shearer, the concentration at any location in the face, and the dust generation rates. The size-consist and density characteristics of the source dust, the air velocity in the face, and the air leakage into the gobs all affect the concentration.

Jan 1, 1995

By R. D. Peterson

Autocad has become the standard graphics package for the mining industry as well as the general engineering profession. This paper discusses the evolution that mine planning has undergone and the trend toward compatibility with Autocad. It discusses the common use of Autocad in mine planning and systems modeling using a program called ICAMPS developed by Ohio Automation. As an example of its usefulness the use of the interactive ventilation network modeling capabilities are discussed specifically and are applied to mine planning at an operating trona mine. The ventilation analysis feature of the ICAMPS software works from Autocad drawing of the as-mined map and the projected mine layout. Using on-screen displays of these maps and the snap-on feature of Autocad, the planner designates nodes in the ventilation network, connects them into branches and selects branch characteristics from a side bar menu. The color coded ventilation network appears with the branch parameters alongside each branch. The software calculates the length of airways, computes the branch resistances where needed, converts the input into the required format and passes this information as input data along to the PENNVEN simulation program written by the Pennsylvania state University. Output is available in graphical as well as report format. The color coded graphs include pressures at the nodes and flow quantities on the branches. Since the networks come from the mine maps, the ventilation schematic displays are to scale and can be plotted separately or superimposed on the mine maps.

Jan 1, 1995

Interaction between rock and fluid plays a critical role in rock engineering ventures such as stimulation of oil and gas wells, geothermal energy recovery and nuclear waste isolation. Robust and reliable design of the related services and underground facilities is based on understanding of the mechanics and chemistry of the coupled hydromechanical- thermochemical processes. This paper explores the application of the theory of such processes in minerals engineering, with particular reference to rockburst mitigation, in situ solution mining and cavity completion of coal-bed methane production wells.

Jan 1, 1995

By Meyer T

Sunburst PCF (Penetrating Cone Fracture) technology has recently undergone extensive underground field trials at Leinster Nickel Operations, Western Australia. Trials with the Sunburst machine started in September 1994 and continued through to December 1994 during which approximately 130 metres of tunnel were developed. The Sunburst technology was used to excavate sub-levels through ultramafic nickel ore for future sub-level caving operations at the Perseverance nickel mine. The Sunburst machine demonstrated reasonable instantaneous advance rates, however, there are still a number of future developments/design changes which need to be addressed prior to the PCF technology being trialed again in a production environment. This paper benchmarks conventional drill and blast at Leinster against the Sunburst Excavator machine performance within similar tunnel dimensions and rock conditions. In addition to productivity and cost information; environmental considerations, support and labour requirements are also discussed. Problems with the current machine design are highlighted and possible future design changes are suggested. The Sunburst machine could be a suitable technology for advancing development through weak to moderate rock conditions and may also reduce overall support costs. With the potential for automation and the ability to reduce rock damage into the development tunnel walls, it is proposed that the Sunburst machine warrants further consideration.

Jan 1, 1995

By Attie J. Goosen, William L. Spiteri

Although the physical characteristics of ANFO made from porous prilled ammonium nitrate (PPAN) have been altered by the addition of crystal modifiers, the optimisation of prilling processes and the admixture of waterproofing agents, the sensitivity of this explosive has not been modified on a commercial scale in the 40 years since its accidental discovery.

Jan 1, 1995

By d&apos, L. F. G. Assumpcao

Kaolin samples from Rio Capim resources were treated in conventional and superconducting magnetic separators to study the main variables that influence the color removal process. Coating clays and delaminated clay were tested. Retention time (or pulp injection velocity), magnetic field intensity and matrix type were the' variables studied. The feed brightness ranged from 84.7 to 87.6 % ISO for the coating clays and from 80.7 to 85.4 % ISO for the delaminated clay. The results showed unleached brightness values higher than 88 % ISO for coating products and higher than 87 % ISO for the delaminated product, using a conventional magnetic separator with an applied field of 1.5 to 2.0 Tesla. With a maximum field intensity in the superconducting machine of 5.0 Tesla, unleached brightness values higher than 88.5 % ISO for both coating and delaminated clays were attained.

Jan 1, 1995

Renison Goldfields is one of Australia's largest mining companies with annual sales revenue over $600 million. It has ten operating mines and processing plants, with operations in most States of Australia and in Papua New Guinea, Indonesia and the United States. The exploration division is active in,other parts of the world, including Europe and South America. RGC produces gold, copper, tin, coal and mineral sands. RGC is typical of companies in the mining industry in that by contrast to the typical pattern in other industries, it is necessary to have systems to handle a variety of different types of operations, a range of size of operations, and operations in remote locations.

Jan 1, 1995

By John W. Kopp, David E. Siskind

Over 4 billion pounds of commercial explosives are used by the U.S. mining industry every year with an excellent and improving safety record. However, accidents involving explosives are seldom minor. They produce a disproportionate amount of fatalities compared to other mining activities, as reflected in the relatively high severity rates. The U.S. Bureau of Mines (USBM) has been analyzing blasting accident data obtained from the Mine Safety and Health Administration (MSHA) to determine the most frequent causes of mine blasting accidents, examining trends in these accidents, and identifying areas of needed research. This paper is an update of three previous blasting accident studies conducted on 4-year intervals by the USBM and published in 1983, 1987, and 1991, and is based on a total of 869 blasting accidents.

Jan 1, 1995

Within the research project "Mine Development" funded by the "Austrian Fonds zur Forderung der wissenschaftlichen Forschung (FWF) " (funds for scientific research) between 1991 and 1993 150 underground hardrock mines in Europe, Northern America, Australia and Japan have been visited to analyze their general design and layout. The main aim of the project was to develop strategies for accessing new underground hardrock mines and to establish a mine planning database. The investigation included mines in high developed countries only, with a comparable labor cost situation. This paper presents the results of one part of the project, which deals with investigations into the influence of different parameters on the design of the primary access for a mine.

Jan 1, 1995

This paper describes experience in designing and implementing casting blasts over the past fifteen years. Important design parameters such as powder factor, burden and spacing, blast pattern geometry, front row burden and toe distance, pit width versus height, blast length, explosive selection, millisecond delay timing and tie-in types are discussed.

Jan 1, 1995