Search Documents

By Kapoor M. L

Emf measurements on SE galvanic cell: SS; Ni-NiO I solid electrolyte/ZrO2 + CaO I [Pb + Bi]liq alloy; (PbO); SS were made in the temperature range 913-1034 K to determine the thermodynamic properties of oxygen dissolution in liquid lead. Bismuth alloys with bismuth in the dilute concentration range of 0 to 3.08 mass per cent and oxygen in the alloy varied by equilibrating the metallic system with a suitable (PbO) slag. Wagner's interaction parameter approach was used to calculate the ternary interaction parameter, eBiO at temperatures of 913, 953 and 993 and 1034 K and to observe the temperature dependence eBiO = 19 200/T - 17.454. Quasichemical fonnulation was employed to yield lnf BiO and reveal the effect of bismuth on oxygen in lead. The results obtained are discussed on the basis of theoretical models and the value of Wagner's energy parameter 'h' estimated to predict the results in a Pb-Bi-O system.

Jan 1, 1995

By Kenneth E. Hay

Researchers from the U.S. Bureau of Mines conducted a field study to assess the safety of remotely controlled mobile roof supports (MRS) in a retreat pillar mining operation, Data were collected to provide the Mine Health and Safety Administration with criteria needed to develop guidelines for MRS use and to determine if precursors could be identified that would alert miners to imminent roof falls. Two test sites at which two different support methods-MRS's and posts were used and were monitored to obtain information on entry stability. Pressure transducers and string pots were installed on all four MRS's to obtain loading and displacement information. and roof bolt load cells. sonic probes, extensometers, and survey targets were installed in the surrounding entries to obtain information on ground behavior. Results showed a larger increase in roof bolt loading and roof movement when MRS's were used, especially in the intersection area. Roof bolt loads in the entries showed decreases in load when the MRS's were set and increases up to 11,1 kN (2,500 lbf) when the MRS's were unloaded. Unloading of one MRS in a pair did not significantly increase load on the other. MRS's I and 2 usually had the higher loads, with these loads increasing as the pillars on each side were being mined. MRS 3 normally had lower loads than I and 2: however, it also experienced some very high loads when in the last position near the pushout. MRS 4 usually had the lowest loads, primarily because it was located near the solid pillar that was not being mined.

Jan 1, 1995

By Joseph A. Whitchurch

The N20 to N25 Tunnel (basic) segment was the second tunnel contract awarded for construction by The PB/MK Team. This project embodied 3.9 km (2.4 miles) of tunnel and was located within the northwest quadrant of the 86.9 km (54 mile) long main collider ring. The contract required the excavation and initial support of a 54.3 m (178 vlf) deep ventilation shaft, a connecting horseshoe shaped Adit and TBM starter tunnel and 3,865 m (12,680 If) long main collider tunnel with a 4.3 m (14 ft) minimum finished diameter. This paper discusses the construction methods, equipment utilized and the production achieved in the construction of the ventilation shaft, connecting adits and the main collider tunnel.

Jan 1, 1995

By Keith Axler

The high reactivity of plutonium metal presents safety concerns related to material containment during fire scenarios. Plutonium metal is liquid at temperatures achieved under selected fire scenarios. The appearance of liquid plutonium challenges the corrosion resistance of the containment materials. However, by the in situ formation of intermetallic compounds, the plutonium metal can be stabilized as solid and the integrity of the containment vessels preserved. Studies have been conducted to demonstrate candidate materials, including lead, which can be introduced to the liquid-plutonium system and bind the corrosive liquid metal through the formation of intermetallic phases. The results of these investigations will be presented along with a discussion of the experimentally determined phase behavior for the plutonium-lead system.

Jan 1, 1995

By Little T. N, Bettess D

For many mining operations the challenge of equalling World Best Practices has become the key motivator for increasing mine productivities and for lowering total costs. In most instances this will only be achieved if mines optimise their total system rather than minimising specific costs within unit operations. In the past, drilling and blasting have been viewed as a cost to be minimised rather than operations which should have their impacts fully leveraged. Once a hardrock orebody is defined the activity which has the most substantial impact in determining the efficiency of a mining operation is the blasting. The output from a blast affects every downstream operation; only by understanding the extent and interactions can the mine be optimised. Substantial improvements to hardrock mining, quarrying and excavation operations are achievable. Instead of seeking the regular one to three per cent improvements based on reduction of consumables, mine operators would be well advised to go for much bigger targets of ten to 30 per cent by fully leveraging the drill and blast operations.

Jan 1, 1995

By Cathy McGinley, John Mullay, Clark Stancavage

The use of crater studies to evaluate explosive performance is a well-established practice in the Blasting Industry. Normally, this work utilizes larger charge sizes (>75mm) in order to minimize the influence of geological factors adjacent to the borehole. This can impose unwanted restrictions in the experimental factors accessible to investigation. Thus, for example, systematic studies of non-ideal performance in a somewhat practical setting is rendered quite difficult.

Jan 1, 1995

By A. B. Cecala

The US Bureau of Mines has designed and evaluated total mill ventilation systems (TMVS) at two mineral-processing operations. Both systems have proven proficient at cost-effectively reducing respirable dust levels throughout the mills. An 11.8-m3/sec (25,000-cfm) system installed at a clay-processing mill provided about 10 air changes per hour(acph). This system reduced respirable dust concentrations by about 40% throughout the mill building. The second evaluation was performed at a silica sand operation. Tests were performed with 23.6 and 47.2 m3/sec(50,000 and 100,000 cfm) of ventilation to the mill building, corresponding to 17 and 34 acph. Average mill-wide respirable dust reductions were 36% and 64%, respectively. This work was done to determine general guidelines and design criteria for operations that may be interested in implementing TMVS. TMVS should be designed to draw clean make-up air in near the base of the mill. This air provides general purging and may clear some dust-laden areas throughout the mill structure. It is discharged at or near the top of the structure. Without the TMVS, dust can exit the building through open doors, windows, etc. and contaminate outside plant workers. This dust can also be recirculated back into the mill building causing additional contamination problems. TMVS is not a stand-alone system. It is a supplemental technique to assist other localized dust control systems (Mody et al.,1987).

Jan 1, 1995

By D. J. MacDonald

This U.S. Bureau of Mines report reviews published information on synthetic berlinite (AlP04) and suggests experimental conditions requisite for its production. Berlinite is a piezoelectric material with potential use as a substitute for quartz in the crystal oscillators, which are components of electronic and electroacoustic equipment. Information gathered here (mostly from published sources) includes historical background, physical properties, end-use applications, criteria of quality, and physio-chemical factors involved in berlinite crystal growth. It is concluded that growing large high-quality berlinite crystal would require high-purity starting materials in an autoclave equipped with a noncorrodible liner and operated with temperature control of ±O.OO5 ac over a range of 250 to 350 ac.

Jan 1, 1995

By A. T. Sapulek, C. S. Özveren, D. W. Dixon

The prediction of underground methane emission from longwall coal faces has been extensively researched for a number of years and numerous prediction methods have been devised. Many coal mines employ sophisticated environmental monitoring equipment which generates large amounts of data including, methane concentration, air velocity and barometric pressure. Presently this information is mainly used only to indicate alarm and danger levels of the monitored data for management purposes, however, the potential uses of this data are enormous[1]. This information could be used to good effect within a production/methane emission strategy as detailed in a previous paper[2]. The paper presents a practical application of artificial neural networks to underground methane prediction. Data on methane concentration and coal production has been obtained from an underground coal mine. The data is used in a neural network architecture and forecasts of methane concentration have been obtained. The forecasts are examined and there is a discussion of the potential use of the predictions from neural networks in the field of mining production control.

Jan 1, 1995

By Feng Dingwu, Chen Jin, Sun Zhongyuan, Peng Shiying

The recent development of rare-earth permanent magnets has impacted the field of magnetic separation. The permanent magnets technology led to the advent of various magnetic separators particularly designed for application in mineral processing. In this paper, a new type of rare-earth PHGMS possessing a higher magnetic field strength in the working zone was developed using finite element analysis techniques. The NdFeB permanent magnets used had properties of 38 MGOe stored energy, and magnetic material flux levels exceed 1.2 T, The combination of scientific and engineering design and suitable matrices can offer an effective separation of industrial minerals, such as kaolin, feldspar, etc. Compared with conventional high intensity electromagnetic separators, the equipment can reduce electrical energy over 80% with lower operation and maintenance costs, and less installation space.

Jan 1, 1995

By R L. Brathwaite

The gold-scheelite-quartz lodes of the Wakamarina valley were the most productive of the mesothermal gold-bearing areas in the Marlborough Schist. Most of the production came from the Empire City and Golden Bar mines which worked the Golden Bar lode. Only 134 m of its 1800 m strike length are accessible, in the No.2 level of the Golden Bar Mine. A fault has downthrown the Golden Bar Mine section by = 47 m and displaced it left-laterally by 18 m. The lode is a typical ribbon-banded mesothermal vein, averaging c. 1.75 m wide, and enclosing narrow horses of schist country rock. It is composed of bands of milky æbuckÆ quartz with thin laminae of schist. Scheelite occurs in short strings of grains within quartz on the footwall side of the lode and also in small quartz-carbonate veinlets in the foot wall and hanging wall schist. The lode quartz contains only localised traces of pyrite and arsenopyrite. They are more abundant in the wall-rock schist.   The Golden Bar lode lies within a steeply dipping normal fault, which, on its footwall side, is adjacent to a 40 m-wide, shallow-dipping mylonite shear zone. Within 1 m of the lode, the shear foliation has been dragged down to nearly parallel the lode footwall. Wall rock alteration is manifested by a marked increase in K and Rb, which correlate with abundant illite/muscovite and K-feldspar within 2 m of the footwall of the lode. Amphibole, stilpnomelane, and pumpellyite show a progressive decrease towards the lode. As and Sb increase close to the lode, but are at background levels within the lode itself. Enhanced Cr (150-430 ppm) in the quartz, relative to the schists (~40 ppm), suggests that the source hydrothermal fluids passed through and leached mafic rocks, such as the metabasites from the hanging wall of the lode (~400 ppm Cr).

Jan 1, 1995

By Jeffrey A. Aldinger

This U.S. Bureau of Mines report presents an analysis of surface coal mining accidents involving mobile equipment for the years 1989 through 1991. Mobile equipment is defined as haulage trucks, front-end loaders, bulldozers, scrapers, and road graders. These five pieces of mining equipment accounted for 20 pct of all surface coal mine accidents and 41 pct of the fatalities. The general discussion of these accidents covers the accident causes, the primary activity of the accident victims, and other contributing factors. A more detailed analysis of accidents associated with each piece of mobile equipment is also provided. This report will provide mine managers and mine safety personnel with a better understanding of the hazards associated with mobile mining equipment. It identifies where improvements in mobile equipment safety can be made and those areas requiring additional safety emphasis, such as safety training, work procedure changes, or engineering changes to the equipment or work environment. The analysis was performed by a team of researchers using accident data and narratives provided by the Mine Safety and Health Administration.

Jan 1, 1995

Rock formation at shallow depths is generally associated with complex geology consisting of many joints, fractures, bedding planes, etc. Fragmentation results from primary blasts in such strata are therefore significantly influenced by structural discontinuities. To evaluate the role of discontinuities, which is of great use in the design of blasts in such conditions, a two-stage investigation program was taken up. In the first stage, model scale tests were conducted with single and double holes with the strike of discontinuities parallel and perpendicular to the face. Later, field studies were conducted in a limestone mine and a coal mine. Blast patterns were modified based on the results obtained from model scale blasts. Secondary blasting was taken as a measure to assess blast performance in the field, whereas mean fragment size, fine and coarse fragmentation indices were considered as fragmentation measures in model scale tests. Model tests indicated confinement of explosive energy by the discontinuities surrounding blasthole. Crater shape and size were significantly influenced by the orientation of joints with respect to the face. Modified blast designs with decreased burden x spacing patterns resulted in improved fragmentation in the field. A reduction of about 12 per cent in explosive consumption was recorded with modified blast designs. Boulder formation was observed to decrease by about 79 per cent as well.

Jan 1, 1995

By René Winand

Due to chemical and electrochemical behavior of the most common additives in copper electrorefining i.e. gelatine, thiourea and chloride ions, it is essential to simulate as far as possible true industrial practice while performing laboratory experiments. The three additives must be studied simultaneously, and added continuously to the electrorefining cell. Ratio electrolyte volume to cathode area; ratio bleed flow to cathode area; hydrodynamic conditions; residence time of electrolyte in the cell; current density; electrolyte and soluble anode must be as near as possible to industrial ones. Experiments performed in the author's laboratory show that under these conditions, reproducible results can be obtained at normal industrial current density and at high current density as well. Problems are however still encountered when developing a sensor for additives monitoring, due to electrolyte redox potential and to substrate influenced thin layer deposition.

Jan 1, 1995

By Hamblyn S

Oakbridge, in combination with its joint venture partner, Nippon Steel of Japan, is expanding its Bulga underground and open cut mines to meet the growing demand for coal in the Asian market. Expansion works underway will see the Bulga underground mine become a world leader in underground productivity, the introduction of a high capacity dragline into the open cut mine (largest capacity dragline in NSW) as well as a major upgrade of the coal preparation plant (CPP) and coal handling facilities (CHF) to process the increased production. This paper describes the planning and implementation of this major expansion program and highlights the rationale behind some key aspects of the program.

Jan 1, 1995

By Ramsay WRH, Morand V

Structural, mineralogical, and textural data from the Tarnagulla Goldfield demonstrate that the area has undergone three significant phases of deformation. The first phase of deformation (Dl) predates the intrusion of the Tarnagulla pluton, which has been dated using K/Ar as 391 ¦ 5MY. We regard this pre-granite deformational event as the major regional deformation. Gold-bearing quartz veins have been deposited in dilational sites on west-dipping reverse faults. These sites demonstrate a geometry related both to faulting associated with Dl and the plunge of the Fl fold axes. This evidence, together with chronology of unmineralised ? D2 and D3 faults, the absence of quartz veining associated with D3 events, and the deformation of carbonate-quartz-biotite-sulphide aggregates within Sl by later S2, lead us to conclude that the bulk of the mineralisation was essentially syn- or late Dl. S'80 values for fluids in equilibrium with vein quartz from Central Victoria have indicated equivocal support for either a magmatic or metamorphic origin. Our evidence supports a pre-magmatic origin for mineralisation at Tarnagulla and hence tends to favour a metamorphic fluid source.

Jan 1, 1995

By Neil A. Brown

The trona deposits near Green River, in southwestern Wyoming are world class in size and quality. They contain more than 25 times the reserves of the next largest trona deposit at Lake Magadi in Kenya. Based on present rates of production, the Green River reserve should last for more than 500 years. Since their discovery in 1938, the Union Pacific Corp. has been instrumental in the promotion, development and production of soda ash in Wyoming. Union Pacific spent several years drilling the deposits and trying to promote them to chemical companies. In 1947, Westvaco and Union Pacific entered into what became the first trona lease agreement. Today, the Green River Basin leads the world in soda ash production, accounting for about 25% of the world's supply. Green River producers process more than 14.5 Mt/a (16 million stpy) of trona to produce more than 8 Mt/a (9 million stpy) of soda ash. The future for Green River soda ash looks good, with more of the world looking towards the cheaper and higher quality source of soda ash coming from the natural deposits. Production from the Green River deposits should continue to grow as trade barriers and tariffs begin to fall in Europe and energy and environmental costs force the synthetic producers to exit the market.

Jan 1, 1995

By Adhikari G. R, Raju N. M

The breaking of rock by explosives occurs so rapidly that the details of the phenomenon cannot he observed by the unaided eye. High resolution cameras and VCRs offer a means of slowing down the blasting action. A high resolution super video camera with digital zoom and a variable shutter speed was imported and used for the first time in India as a tool for blast optimisation studies at Malanjkhand Copper Project. Slow motion play-back revealed that the gases vented out through the fissures. The crest moved prior to the lower portion of the bench when initiated with detonating cord. The delay timing between the rows was not enough to provide sufficient relief and rock movement. This inadequate delay timing resulted in flyrock from the back rows. Stemming ejection was observed from practically all the holes. The muck profile was not satisfactory. A trial was carried out using 450 ms in hole delays and 25 nis surface delays. The front row holes were drilled based on the observations made from the laser profiling survey system. The video of the monitored blast showed that the rock started moving prior to the stemming ejection. It could be clearly seen that the entire block was completely initiated through the surface delays before the onset of the burden movement, thus eliminating any chance of misfires. Viewing blasts in high quality slow motion was useful to arrive at modified design parameters, resulting in uniform fragment size distribution and controlled rock movement.

Jan 1, 1995

By F. Seymour

A modified 3D Lerchs-Grossmann (LG) graph tree algorithm is presented that generates the complete set of nested maximum valued pits in a single run. This modified LG algorithm looks at the relative strength (average value) of the branches (groups of blocks). Pointers are allocated and pruned until there are no members of weaker (lower average value) branches overlying members of stronger (higher aver-age value) branches. The final set of strong branches are listed in order of decreasing strength. The pits they represent form the maximum valued convex hull for a single variable pit limit parameterization. A description of the algorithm is given along with examples of how it has been applied at Newmont.

Jan 1, 1995

By Jensen B, Ofori P, He Y, White E, Stanmore B, Brien M, O&apos

As part of a large AMIRA project, an on-line moisture meter was installed at two mine sites in Central Queensland. This project investigated the factors which control the moisture content of coarse (>0.5 mm) coal from the centrifuges used in conventional coal preparation plants. It was placed immediately after the first centrifuge to isolate the factors pertaining to one machine and its feed.The meter was found to be accurate and precise when compared with manual and mechanical sampling methods. The Grubbs estimator technique indicated that its precision is better than 0.3 per cent at the 95 per cent confidence limit.It has been identified that:1. the variability of the measured moisture contents of coarse coal can be described by normal distributions. Standard deviations of about 0.6 per cent are common; and2. the treatment of the coarse coal on the drain and rinse screens immediately prior to the centrifuge can affect the final moisture content.

Jan 1, 1995