Search Documents

By P Stone, J. M. Cook, P. R. Simpson, C Mcdermott

Paper presented at the conference Economic geology in Europe and beyond II, models for mineral deposits in sedimentary basins, held in Keyworth, UK, 13-14 April 1994. The SW part of the Southern Uplands is a back-arc section of an accretionary thrust system, divided into structural blocks by major NE-SW shear zones and NW-SE faults forming the margins of Permian half-grabens. The highest arsenic levels in stream sediments (over 65 ppm) are associated with those blocks carrying brittle-ductile transition fabrics. Three factors combine to recomend the area as having potential for gold mineralisation: As-rich greywackes as country rock, felsic intrusions and a major shear zone. Selected stream sediments were analysed for gold using lead fire assay with ultra-pure flux and ICP-MS finish. Several localities showed over 15 ppb Au, the three most significant being within the hanging wall of the Orlock Bridge Fault and each having distinct characteristics

Aug 1, 1995

By F. Tailoka

Bi was electrorefined from alloys containing 10-90 wt% Pb, together with Cu and Ag as minor impurities, in a basic cell and in a recessed-channel cell with 27.5:72.5 NaCl-PbCl electrolyte at 450-470 degrees C and 10 000-20 000 A/m2. The voltage in the basic cell was as high as 9 V, with some carryover of Bi to the cathode observed, whereas in the recessed-channel cell it was as low as 285-635 mV. Flow patterns observed in a room-temperature model indicated that the recesses provide both static liquid hold-up and good mixing of the alloy, enhancing cell performance in combination with the reduced anode-cathode distance of 0.90 mm. The purity of the resulting anode product is as high as 99.9%

Aug 1, 1995

"U.S. Bureau of Mines Publications and Articles, 1994 with Subject and Author Index Compiled by Office of Public Information U.S. Bureau of Mines (USBM) Department of the InteriorINTRODUCTIONThe U.S. Bureau of Mines (USBM) was established in 1910 to conduct inquiries and scientific and technological investigations on mining and the preparation, treatment, and use of mineral substances; to promote health and safety in the mineral industries; to conserve material resources; to promote economic development; to increase efficiency in the mining, metallurgical, quarrying, and other mineral industries; and to inquire into the economic conditions affecting those industries. The organic act of the Bureau, as amended by Congress and approved February 25, 1913, made it the province and duty of the Bureau of Mines to ""disseminate information concerning these subjects in such manner as will best carry out the purpose of this Act.""In accordance with this directive, USBM reports the findings of its research and investigations in its own series of publications and also in articles that appear in scientific, technical, and trade journals; in proceedings of conventions and seminars; in reference books; and in other non-USBM publications. This edition describes reports and articles published during calendar year 1994. It supplements the 50-year list of Bureau publications issued from July 1, 1910, to January 1, 1960; 1 the 50-year list of articles by Bureau authors published outside the Bureau from July 1, 1910, to January 1, 1960; 2 andthe 5-year lists of publications and articlesfrom January 1, 1960, to December 31, 1964,3from January 1, 1965, to December 31, 1969,4from January 1,1970, to December 31,1974,5from January 1,1975, to December 31,1979,6from January 1,1980, to December 31,1984/and from January 1, 1985, to December 31,1989.8"

May 1, 1995

By R. Venugopal, T. C. Rao, N. Suresh

Experiments were carried out using the cyclone to treat coal in the size range -2.0+0 mm. The diameters of the cyclone outlets (vortex finder and spigot) were varied to study their effects on cyclone performance. The cyclone products were deslimed over a screen with an aperture of 0.075 mm. The performance of the separator was studied for washing coarse coal (-2.0+0.075 mm) and fines (-0.075 mm). Performance curves were plotted for the separation of -2.0+0.075 mm coal. The concept of a generalised distribution curve was adopted to predict cyclone performance. A mathematical representation was derived from the generalised distribution curve. The specific gravity of separation for individual size fractions showed a decreasing trend with decreasing particle size down to 0.85 mm, beyond which a reverse trend was noted. It was also found that the fine size fraction (-0.075 mm) does not separate on the basis of size or specific gravity but follows the water distribution

Apr 1, 1995

By B. Denby

sintered ores, to be removed by a pneumatic,

Apr 1, 1995

By R. J. Gochin, M. A. Diaz

A modified Hallimond tube is described which allows the determination of the ultimate recovery R and the flotation rate constant k in a single, continuous experiment. The range of fine particles which can be satisfactorily floated with the modified apparatus can be extended by increasing the length of the bottom part of the tube. Findings suggest that pyrite and arsenopyrite can be separated in alkaline suspension using the so-called F series of collectors. Lime was found to act as a depressant. The collectors operate under pH and dosage control and do not require other depressants. Collectors used in the study were thio-amine (a cationic surfactant) and alkyl propionamide (a non-ionic surfactant)

Apr 1, 1995

By ed. comp., S. H. White, A. J. Naldrett, P. R. Simpson

Peter Simpson's introduction, Tony Naldrett's concluding remarks and discussion by Prof. White of D.M.A. Flight's report of the proceedings are presented from the conference held in Keyworth, UK, in April 1992

Apr 1, 1995

By G. J. Hearn

between particles in the classifying region is then

Apr 1, 1995

By A. P. Whittlestone, J. D. Johnson, R. J. Pine, M. E. Rogers

standpoint. The effect on efficiency of collisions

Apr 1, 1995

By M. W. Robotham, H Wang

removal efficiency is analysed from a stochastic

Apr 1, 1995

By S. A. Sayed, M. N. M. Ahmed, M. A. Doheim

The performance of a 12.7 cm hydrocyclone was investigated by considering the effect of design variables (diameters of the vortex finder and apex) and operating variables (pressure drop and solids content of the feed) at a medium feed solids concentration of mixed minerals. Cut-size was found to be the most important parameter in hydrocyclone design and operation. The effect of feed pressure in reducing hydrocyclone cut-size is less pronounced at medium feed solids concentration with a mixed mineral feed. The choice of vortex finder diameter and apex diameter becomes more sensitive at medium feed solids concentrations. The effect of feed solids concentration in increasing the cut-size becomes less marked at higher concentrations. Predictions of an empirical model were found to be in good agreement with experimental data. Comparison of results obtained from the model with those predicted by theoretically derived models showed the latter to be more promising, with the turbulent two-phase model giving closer agreement with the experimental data

Apr 1, 1995

horizontal-type classifier prior to charging into a blastfurnace.

Apr 1, 1995

By F. Tailoka, G. Zhao

Pb is an unwanted impurity in Al for which there is no established method of removal. As it interacts strongly with alkali metals, separation was achieved by adding Na or K to molten Al at 953-1 003 K. Direct Na addition led to considerable evaporative loss but in-situ addition by electrochemical titration from a eutectic NaCl-KCl or KCl-BaCl2 mixture was found far more effective, in some cases reducing Pb content below detection levels within 2 h of titration. K appeared more effective than Na at low Pb concentrations but the use of Na was preferred as it is less toxic and explosive. Na removal from Al-Na and Na-Pb alloys was also carried out electrochemically, the use of these two alloys rather than the eutectic salt as a source of Na avoiding liberation of Cl2 at the anode

Apr 1, 1995

By B. E. Burakov, S. D. Lupal, O. A. R. Thalhammer, B. Saini-Eidukat

Electric-pulse disintegration is a mineral separation technique that liberates all mineral grains from any igneous or metamorphic rock irrespective of its lithology or grain-size distribution. The normal mechanical crushing of whole-rock samples is replaced by the rending effect of an explosion, produced by applying an electric current from a high-voltage power source. A voltage greater than the 100 kV necessary for the electrical breakdown of rock samples is achieved by using capacitors charged in parallel, but discharged in series. The sample sits in a water bath and the rapid distribution of electric pulses leads to an explosion which occurs preferentially along grain boundaries of the sample. Individual, undamaged mineral grains can be recovered in their original shape and form regardless of grain size. Examples are given of the liberation and concentration of important accessory minerals from different rock types. The examples show the recovery of diamond from two types of non-kimberlitic host rock in Popigai and Kumdykol in Kazakhstan and platinum group minerals associated with chromitites from the Konjdor intrusion and sulphides from intrusions in the Kola Peninsula in Russia

Apr 1, 1995

By T. G. Carter, R. I. Miller

First, the influence of variation in the

Apr 1, 1995

By A. C. Apling, N. B. Barrett

Roadstone production requires the generation of non-flaky material, as outlined in British Standard 812 section 105.1; with respect to this criterion, a mathematical model of a cone crusher must be able to predict the flakiness index of a particular size range as determined by the relationship between thickness and nominal size. The Whiten cone crusher model utilises breakage and classification functions to predict a product particle size distribution only, so a shape function has been proposed that is based on a phenomenological approach, taking into account the transfer between flaky and non-flaky material at each stage of breakage. The results of laboratory tests to determine material breakage characteristics and of examination of pilot-scale test products illustrate the method's potential

Apr 1, 1995

By B. M. England, M. V. Swain, N. Bristow, R. D. Dukino

The toughness and fracture mechanisms of ores with significantly different microstructures from Yandi, Koolan and Mount Whaleback were studied with a view to understanding their degradation behaviour. Bulk fracture toughness was determined by the 3-point single-edge notch beam test and the results interpreted using Weibull statistical analysis; indentation fracture mechanics was also used to measure fracture toughness of the different mineral forms and to understand their response to contact fracture

Apr 1, 1995

By Boorder De, B. S. Panov, A. B. Westerhof, V. A. Korcemagin

Paper presented at the conference on Economic geology in Europe and beyond II, models for <mineral deposits> in sedimentary <basins>, held in Keyworth, UK, 13-14 April 1994. The Hg and Sb deposits of the Mediterranean and Circum-Pacific Belts are often found at elevated structural levels, suggesting that their preferential occurrence in young orogenic belts is not a fundamental metallogenic feature but merely reflects their chances of surviving post-orogenic peneplanation. In western Europe their emplacement appears often to be related to late orogenic extensional events accompanied by a notable increase in heat flow. Although Nikitovka and Almaden have quite different settings, both appear to be related to deep-reaching shears. Together with brittle fault zones at higher levels, these provided pathways for fluid phases that originated at least partially within the mantle. The Nikitovka deposits are located in the Donets segment of the 2 000 km Pripyat-Dniepr-Donets palaeorift in the East European Platform. Initiated in the mid-Devonian with a possible Precambrian precursor, its listric boundary faults displace the Moho from a depth of about 50 km north and south of the rift to 35 km along the axes of the Pripyat and Dniepr segments. The steep central anticline of the Donets segment, within which the main Hg-Sb district is located, is interpreted to be associated with a reactivated fault reaching into the upper mantle. The Almaden syncline, formed during the Variscan Orogeny, may be an older pull-apart basin or half-graben associated with the collapse of the Cadomian Orogenic Belt. It is situated on a major ENE-WSW-striking shear zone which may represent a Late Cadomian transfer zone reaching into the mantle

Apr 1, 1995

By I. L. Whyte

apparent density and drag coefficient of porous ores on

Apr 1, 1995

By A. Dean, J. Roberts, I. Stone, J. R. Merefield

Paper presented at the conference: Risk assessment in the extractive industries, held in Exeter, UK, 23-24 March 1994, and first published London: IMM, 1994, preprint volume, 10pp., 11 refs. No completely reliable method for characterising and quantifying airborne dust risk exists. A new monitoring technology has been developed whereby dust collected from four-way directional and high volume samplers is analysed for mineral content and particle size for integrated dust mapping. A dust database was set up for the area surrounding the Ffos Las open cast coal site in South Wales. It included XRD directional traces from 17 gauges over 20 months, XRD traces from window ledges in the nearby communities, the major soil types in the area, dust data from haulage roads and public roads and reference-type mineral samples. The database can be accessed relationally to compare and analyse the data using mineral, direction, time, weather and geographical relationships. The data has been used to assess areas of low, intermediate and high levels of risk from dust fall-out

Apr 1, 1995