Search Documents

The Lennard Shelf Operations owned by Western Metals Ltd evolved from the Cadjebut Zinc Lead Mine (BHP) in August 1994. Original production of 0.5 mtpa will rise to 2.0 mtpa at the end of 1998. Employees work a multiple of fly-in/fly-out (FIFO) rosters from the Kimberley region and the WA Capital. The three underground mines, treatment and services departments will employ approximately 300 people by the end of 1998. The expansion of the Lennard Shelf Operations as a remote mining location was based on a fresh look at management systems and employee rosters which were generated from many years of mining experience. This paper will endeavour to summarise these experiences and analyse some of their outcomes. Dealing with several mining methods, engineering difficulties, logistical problems and climate extremes, the Lennard Shelf Operations has managed social/employee issues with excellent results. Much time has been spent to get this correct for the Lennard ShelfÆs own set of circumstances. Employees and associated companies must expect continuing changes and improvement as Western Metals strives to continually improve its management systems and employee rosters.

Jan 1, 1998

By Tracy Brettmann

The use of rock-socketed Augered Cast-In-Place (ACIP) piles is new to the Austin and central Texas region. This case history describes the design methodology, load test results, quality control procedures and the rate of production pile installation for the first large commercial project where ACIP piles were used in Austin. The piles were 24 inches in diameter and extended through about 45 ft of alluvial materials to be socketed 6 ft into limestone. A full-scale instrumented load test was performed on a test pile that was loaded to 452 tons and held for 24 hours. Telltales were installed in the middle and the tip of the test pile. As part of the overall quality control procedures, singlehole sonic integrity logging was performed on the production piles to verify structural integrity during pile installation. During pile production, an average of 14 piles per day were installed, which is approximately seven times faster than the original design that consisted of drilled shaft foundations.

Jan 1, 1998

In-seam drilling is conducted mainly to drain coal of gas and/or water prior to development or extraction. The requirements of inseam drilling for gas drainage have mainly surpassed the technical limits of rotary drilling and are mainly being addressed by guided down hole motor drilling, albeit at a higher cost. There is an increasing application of in-seam drilling to detect geological structures or other hazards or their absence in advance of mining to reduce the risks of underground mining. Close collaboration between miners, drillers, geologists, researchers and suppliers over the last four years has seen many advances made to improve the accuracy and reliability of inseam drilling. With such developments will come closer control over the ventilation and safety of future mining under deep gassy conditions, but not without costs. The paper summarises the current applications of inseam drilling, recent technological advances and the next generation survey and geophysical sensing tools which are currently being developed

Jan 1, 1998

By Alastair Grogon

Proper coupling of a geophone to a monitoring surface is probably the single most important step in accurately recording and measuring ground vibrations from a blast. Over the years, a number of monitoring methodologies have been published. Some of these were published as a "standard", by organizations such as the International Standards Organization, others as suggested methods by various authors in papers or text books, or in the users manuals supplied by seismograph manufacturers. These monitoring standards differ, and are sometimes apparently contradictory. The purpose of this paper is to summarize the coupling methodologies from a number of these "standards", point out similarities and differences, and discuss the technical basis behind some of the different methods.

Jan 1, 1998

By L. A. Henry

The island of Jamaica consists predominantly of Carbonate rocks which vary in chemical & physical characteristics. Currently these rocks are used for construction and road aggregate, landfill and as a raw material in the manufacture of cement. Over the past fifteen years the Geological Survey of Jamaica with assistance from a number of international aid agencies and the private sector have identified deposits of high calcium/high brightness limestones which have the potential to be utilized as a high quality filler and a number of other commercial applications. Geologically, these limestones are formed within the Eocene Swanswick Formation, the Oligocene Walderston-Browns Town Formation and to a lesser extent the Miocene Montpelier and Newport Formations.

Jan 1, 1998

By M. A. S. Martins, J. C. Guillaneau

Steady-state simulation has been proving its usefulness and efficiency in process design and optimization for many years. Steady-state simulation is a very effective approach for plant design since it enables a great number of hypotheses to be considered regarding flowsheet, equipment etc., the processing equipment and material handling equipment to be sized, and the configuration of almost optimal industrial plant to be attained in a very short time. This paper will present the basic principles of mineral process simulation methodology and some real case applications of their capabilities in several complex ores in Brazil.

Jan 1, 1998

By R. Scott

This article describes and evaluates the establishment of Kuyasa Mining including the search for a suitable deposit, the ongoing lack of finance, and market constraints. Despite the dramatic initial growth and success of their Ikhwezi Colliery near Delmas, Mpumalanga, Kuyasa?s experiences offer some sobering arguments for significant changes to mineral rights ownership, the attitude of financial institutions and government policy if South Africa is to have a dynamic and successful junior and small-scale mining sector.

Jan 1, 1998

By C R. Fountain, W R. Cannings

The zinc-lead-silver mineral resource at Lady Loretta ranks amongst the worldÆs richest when measured in terms of in situ metal grades. However, the project remains undeveloped 28 years after its discovery in 1969. The primary obstacle to development has been the fine and complex grain structure of its ores, which make flotation concentration inefficient even with fine grinding. The size and remote location of the deposit have also hindered exploitation. BUKA planned to directly fume the volatile target metals from the ore when it acquired the project. Intensive, post-acquisition modeling showed the innovative processing route to be uneconomic, notwithstanding high metals recovery and low waste content in fume product. Progressive modifications and supplements to the underlying fuming process enhanced economics and resulted in a new mine-to-metal processing route for zinc-lead-silver ores. The proprietary, three-stage BUKA Zinc Process offers technical, economic and environmental advantages. It is expected to find widespread application in the treatment of ores and residues. However, neither continued R&D nor application to Lady LorettaÆs currently delineated resource can be justified under prevailing market conditions. The objectives and results of each step in the process development sequence are outlined with reference to their impact on the commercial viability of the Lady Loretta project.

Jan 1, 1998

By Andre L. De Vegt

Hydrogen sulfide is an expensive chemical used in nickel, zinc and copper mining and metallurgical operations for selective recovery and concentration of metals, from leach water streams, acid plant blow down streams, refinery electrolyte bleeds and precious metal, plant bleeds. Hydrogen sulfide is either produced on site by catalytic reduction of elemental sulfur or transported to the site as liquefied hydrogen sulfide (H2S) or as a sodium sulfide solution (NaHS) Biologically produced hydrogen sulfide has economically very interesting, application possibilities in the mining and metallurgical industry. Converting sulfates from waste streams into usable hydrogen sulfide by biological reduction results in operational cost savings in existing lime treatment systems. H2S can be produced biologically for less-than $500/ton S. For the past ten years Paques has been engaged in the development and installation of treatment systems based on biotechnological processes to remove sulfur compounds from water, air and gaseous streams. Paques has designed and installed a groundwater treatment system for the Budelco zinc refinery in the Netherlands to remove sulfate and heavy metals. The hydrogen sulfide produced is used for recovery of metals,, mainly zinc, from the ground water stream. The system has been operating since May 1992 treating a flow of 5000 m3/d. At Kennecott's Bingham Canyon Utah copper mine, a pilot plant started operation in November 1995 to develop the process for selective recovery of copper from leach water using biologically produced hydrogen sulfide from sulfate containing groundwater. Other pilot plants are operated at DOE's Pittsburgh Research Center and at Cominco Research focusing on selective recovery of metals.

Jan 1, 1998

By M. Carvalho, R. Bicallho, M. Queiroz, R. Gomide, V. Silva, R. Toubes

Since it is becoming increasingly important, from an environmental viewpoint, to minimize blast vibrations induced in urban dwellings and improve rock fragmentation in order to reduce costs with loading, transportation crushing and grinding, a cooperative research project was established between Companhia Vale do Rio Doce - CVRD and the Blasting Research Group in the Department of Mining Engineering at Escola de Minas - UFOP to investigate which elements interfere on ground vibration, air blast, flyrock and rock fragmentation related to rock blasting activities at Conceição Mine, located in Itabira city, state of Minas Gerais, Brazil. This research also involved development of a new explosives formulation in order to minimize the total blasting cost. This paper presents the general scheme of the research running from May 1995 to May 1997 and a summary of the results obtained in the field tests that were carried out in this mine.

Jan 1, 1998

By K. H. McDaniel, K. G. Wallace

This paper describes the development of a Windows-based interactive mine ventilation simulation software program at the Waste Isolation Pilot Plant (WIPP). To enhance the operation of the underground ventilation system, Westinghouse Electric Corp. developed a program called WIPPVENT. While WIPPVENT includes most of the functions of the commercially available simulation program VNETPC from Mine Ven- tilation Services Inc. and uses the same subroutine to calculate airflow distributions, the user interface was completely rewritten as a Windows application with screen grap-hics. WIPPVENT is designed to interact with WIPP ventilation-monitoring systems through the sitewide central monitoring system. Data (e.g., air quantity and differential pressure) can be continuously collected from the underground ventilation remote-monitoring and control system and from the mine's weather stations (psychrometric data). Furthermore, WIPPVENT incorporates regulator characteristic curves specific to the site. The program utilizes this data to create and continuously update a real-time ventilation model. This paper discusses the design, the key features and the interactive capabilities of WIPPVENT.

Jan 1, 1998

The Boliden Aitik concentrator in Sweden processes 2,000 tph of low grade copper ore. The plant consists of five grinding lines feeding four bulk flotation banks with a scavenger concentrate regrind mill, and a column cleaner circuit with a regrind mill. The authors installed a model-based expert, optimizing control system to maximize copper recovery in the bulk flotation circuit while maintaining an appropriate copper grade in the cleaner feed. The optimizing control system uses on-line assays and calculates and implements set points for cell pulp levels, air rates and reagent addition rates. It combines the power of a dynamic population balance model which estimates mineral liberation in each stream, an optimizer which computes appropriate set points and a rule-based module which implements the strategy. The benefits have been evaluated over three months. The model-based expert, optimizing control system generates a measurable increase in copper recovery, around 0.5 per cent and an optimized bulk concentrate grade. The need to maintain the optimizing control system and other practical aspects are discussed.

Jan 1, 1998

Interactive data exploration is essential for visualising grade distribution and geological controls on orbodies. Quick and appropriate computer techniques for making daily 'value adding' decisions include routine imaging of numerical data suc

Jan 1, 1998

Goldfields (Tasmania) Limited operates a small, high-grade underground gold mine on the West Coast of Tasmania, 30 kilometres north of Queenstown. The main orebody, Zone 96, was discovered in 1989, with major development work commencing in 1993. The mine was officially opened in July, 1996. Initial production came from a shallow orebody known as the Sill Zone, some 50 - 150 m below surface, which was accessed by a 1 in 8 decline. Zone 96 lies between 350 m and 550 m below the surface and is accessed by a 402 m deep, 3.2 m diameter internal shaft from the collar level located 100 m below surface. The main ore extraction system in Zone 96 is mechanised cut and fill, using high density paste fill. Run of mine ore and waste are hoisted in a single 5.5 tonne overturning skip, then trucked from the underground collar to the gold plant ROM pad or waste dump, respectively. Ground conditions in the mine vary with orientation and proximity to major faults. The gold is contained in a sequence of strongly altered volcanic rocks adjacent to the Henty Fault. Most of the gold is contained in massive quartz, ranging in width from 0.5 m to 7 m, which has been subjected to substantial faulting. Average mineable grade is about 27 grams gold per tonne. Ore reserves in 1996 proved an initial mine life of approximately 4.5 years at 90 000 ounces gold per annum, with significant potential for additional resources from extensions to Zone 96 and adjacent zones. The lease is located in an environmentally sensitive area and a very high standard of environmental management is an essential part of the operation. This paper describes the relevant aspects of mining at Henty including grade control, ground support, backfill placement and environmental management.

Jan 1, 1998

By Mike Higgins

"Data management is emerging as a major concern for miners. Engineers today are faced with anextensive array of data from varying sources, and are required to consolidate and analyse thisinformation to produce an effective and efficient mine plan. The viability of a mining operation canbe dependent on the outcomes of this process. With so much at stake, it is no surprise that mostengineers prefer a standard approach to blasting which is designed to minimise risk rather thanoptimise performance."

Jan 1, 1998

By David A. Jack

The Mission Valley Viaduct is located in San Diego, California. This structure is the intersection of Interstate 8 and 805. The project consists of the main viaduct, 8 connecting ramps, and one highway overpass. This job was originally built back in the 70's. After the Loma Prieta Earthquake in 1989, Caltrans began an aggressive program to seismic retrofit all of its bridges throughout the state. Most retrofit designs required major upgrades to the existing footings. These footing upgrades consisted of either driven or drilled shaft piling. The existing footings of the Mission Valley interchange were supported on driven H pile. The soils throughout the site were dense sands and gravels, cobbles, occasional boulders with a dense sandstone bearing strata, which varied through out the site. It was this sandstone strata that the engineers designed their pile tips around. High ground water in sandy soils created a high probability of liquefaction in all of the upper stratas.

Jan 1, 1998

By Patrick R. Taylor

Titanium nitride has been synthesized in a thermal plasma reactor from ilmenite ore concentrate using methane and ammonia as the reactive gases. The product has been characterized by x-ray diffraction and SEM. Results show that a high concentration of methane favors the formation of iron, titanium nitride and titanium carbonitride. The formation of titanium carbonitride can be minimized by controlling the concentration of methane. The formation of TiN proceeds by the progressive reduction of the oxides of titanium to titanium, which is converted to titanium nitride.

Jan 1, 1998

By M Cooper

Since its enactment in 1991, the Resource Management Act (RMA) has generated both praise and criticism. The major criticism is in relation to the costs the Act poses to industry and the time it takes to work through the process. In response to such criticisms the Minister for the Environment has initiated a review of the implementation of the RMA. The Minister's proposals for reform have not yet been released and the discussion that follows is based upon the report by the Minister's Review Group which was released in September.

Jan 1, 1998

By S. Liu

A general account of nitrogen-generating systems, including the surface fixed, surface-mobile and underground-mobile types is presented. These systems have recently been adopted in coal mines in China to prevent and extinguish fires. The paper stresses nitrogen -injection technology and relevant systems of monitoring and stopping air leakage.

Jan 1, 1998

By K J. Kidd

There is general understanding of hoisting systems throughout the mining industry. However, the relative importance of the various parameters influencing hoist selection and utilization is not completely understood. In order to determine if these parameters can be identified and prioritized, data covering 613 hoist installations were compiled. The 613 installations represent hoisting systems in 30 countries on six continents. This study compares data to historical trends, correlates design parameters in an attempt to identify underlying selection criteria, and comments on the apparent trends in recent developments in hoist design.

Jan 1, 1998