Search Documents

By Midori Sakamoto, Nobuaki Sakuma, Tsuyoshi Murashita

Recently, tunnel blasting works near the residential area and existing building are increasing and environmental problems caused by vibration have become serious public concern. In order to solve these problems, blasting works have been conducted with segmented blasting and reduce advance per round. However, with these blasting, work efficiency is not obtained, and regrettably the cost and risk of accident tend to increase. We developed a new controlled tunnel blasting technique with electronic delay detonator. Electronic delay detonator can supply extremely large range of delay period which could not be achieved with conventional pyrotechnical delay detonators. We utilized advantages in initiating hole by hole over entire tunnel face at the same round. Much seismic data obtained from tunnel blasting with conventional detonator was statistically analyzed in order to find average duration time of vibration caused by a single hole initiation. Numerical simulation using sample waves from a single hole initiation was carried out in order to find an optimum delay time which can separate vibration in each hole initiation and without decreasing blast performance. Trial blasting was conducted to examine the correctness of optimum delay time obtained from numerical simulation. This blasting technique was applied to an actual tunnel construction. This tunnel is 2 lane automobile tunnel with a total length of 659 meters and internal cross section of 70 square meters. The purpose of the use of blasting technique on occasion, was the protection of fresh water reservoirs directly above the tunnel, and to keep the effect on local private houses to a minimum. The vibration level against this station was limited under 20 mm/see P.V.V. With this blasting, the tunnel construction was completed without exceeding the limited vibration level, with minimum cost and construction time.

Jan 1, 1998

By Stephen C. Britten

An in-situ amperometric slag sensor for measuring the concentration of easily dissociable oxides in slags at temperatures between 1200-1600°C is being developed. The sensor provides the same information as potentiometric sensors while also providing data on the concentration of the transition metal species and the diffision kinetics within the slag. The electrochemical technique utilized in the sensor is similar to methods utilized in aqueous voltammetry.

Jan 1, 1998

By R. J. Sweigard

Stabilization of slopes on abandoned mine land (AML) invariably involves some channelization to control surface drainage. Typically, these channels are lined with riprap or gabions, depending on gradient and expected flow rate. The conventional treatments pose a problem since they require frequent maintenance and replacement at times. Soil bioengineering presents an alternative to the conventional measures. In soil bioengineering, living woody plant material forms the main structural component in systems designed to prevent shallow mass slope failures, surface erosion, and channel bank erosion. An experimental application of soil bioengineering techniques was designed and implemented at an AML site in eastern Kentucky. The design consisted of live fascines and live stakes using willow branches installed with coir geotextile. Channel gradient, length, and cross-section were considered in the design.

Jan 1, 1998

By Peter Cain

In 1993 an opportunity presented to monitor the effects of undermining an abandoned roadway by a longwall panel in the Sydney. N.S. coal field. Interaction subsidence data was collected by survey leveling to benchmarks in the undermined gateroad as well as by a standpipe system equipped with 15 vibrating wire piezometers measuring changes in elevation in the gateroad relative to an outby header tank. The piezometers were monitored at 30 minute intervals using a datalogger. while the leveling surveys were conducted weekly over the life of the project. The monitoring program resulted in the collection of a very large both of data. relating vertical subsidence to the relative position of the underlying face. The most basic analyses derived a travelling subsidence curve from the leveling data only. which hinted at a relationship between rate of extraction in the panel below and the amount of strain developed in the undermined strata. The complexity of the relationships between the amount of subsidence obtained, the location of' the individual monitoring stations, the rate of face advance below and the potential for "periodic" subsidence due to geological conditions has made analysis difficult. and the amount of data has compounded this problem. Recently. an analytical approach using a commercial neural network analysis package has been applied. which appears to have resulted in the ability to draw sonic meaningful conclusions from the data set. In this paper a short history regarding the collection of the data set is followed by a brief' description of neural networks. This is followed by a description of the several analyses performed. some of the results obtained, and conclusions drawn.

Jan 1, 1998

By Cceliksirt, V Erkan

This computer program has been developed under the field conditions for use in control of surface drilling-blasting operations. This paper outlines the relevance of fragmentation to quarrying, open pit mining or road cutting and key features and operating principles of the software (DelPat for Windows 95).

Jan 1, 1998

By Dirk Bleazard

Barrick Goldstrike Mines is improving the reliability of mining and processing equipment through the use of failure analysis and condition monitoring activities. Program results include an increase in equipment capacity and an overall reduction in operating costs. Identifying equipment failure modes and developing associated capital asset management practices can minimize failure consequences. Successful programs have included alterations to management practices, equipment modifications, and/or the implementation of condition monitoring programs. By controlling or minimizing the effects of incipient equipment failures, corrective actions can be taken earlier in the failure cycle. This results in an associated reduction to repair costs and equipment down time. Mining companies invest in their capital assets to provide the capacity necessary to meet operational needs. Over time, functional failures occur that reduce this productive capacity. Diagnostic technologies now exist that allow the condition of equipment to be monitored. Early response to this information minimizes the effects of functional failures and restores equipment re- liability. Reliability is a performance indicator of overall equipment condition. It is most often expressed in terms of mean time between failures. When the established objectives of a capital asset management program include the maximization of this failure interval, trailing indicators, such as availability and operating cost improve. The probability of equipment failure is influenced by engineering design and operating conditions. The performance level resulting from this operating environment is expressed as "inherent reliability." Without maintenance intervention, equipment will ultimately fail to perform its intended function and become less reliable. Therefore, maintenance must be managed as the supplier of reliable operational capacity. Maintenance can only supply equipment performance that approaches the level of inherent reliability. Actually achieving inherent reliability requires that all maintenance decisions are made at the economically optimal time. Enhancing performance levels beyond inherent reliability can only be achieved by altering operating conditions or practices or through physical equipment modifications. An evolution in maintenance management philosophy has been under way since the beginning of the industrial revolution. As equipment has become more sophisticated, so have maintenance practices. At the beginning of the industrial age, equipment tended to be over designed and slow moving. The first maintenance philosophy was one of reactive maintenance. Maintenance intervals were dictated by the operational status of the equipment. As a result, production interruptions were common and capacity needs were met through an investment in redundant capital assets.

Jan 1, 1998

By D. Neuschiltz, M. Witthaut, R. Cremer

"Metastable (Ti,Al)N coatings with fee structure have been shown to exhibit superior performance as compared to TiN under conditions of wear at elevated temperatures due to their better oxidation resistance and hardness. The oxidation resistance of these coatings increases significantly with increasing Al-content. However, the deposition of (Ti,Al)N films with Ti/ Al ratios below about 30/70 leads to a hexagonal structure which is not suitable for tribological coatings. Only little is known about the location of the cubic to hexagonal phase transition and hence about the optimum composition of (Ti,Al)N hard coatings.To determine the position of this transition, Tii-xAlxN films with different Ti/Al ratios were deposited on high speed steel at substrate temperatures between 100 and 700 °C by means of reactive MSIP. The composition of the films was determined by electron probe microanalysis (EPMA) and X-ray photoelectron spectroscopy (XPS), the crystallographic structure by thin film X-ray diffraction (XRD).It could be shown that in case of deposition temperatures of 300-700 °C a two-phase region exists in the metastable TiN-AlN phase diagram, which expands with increasing temperature, wheras at 100 °C substrate temperature no two-phase region was observed. But in opposition to the phase diagram known from literature, which is based on thermodynamic estimations, the detected two-phase region is narrow for typical PVD temperatures, thus allowing the deposition of cubic single-phase Al-rich (Ti,Al)N hardcoatings for tribological applications. Based on these results, a new Ti1-xAlxN film with x = 0.62 has been developed, which showed an increase of oxidation resistance by a factor of 4."

Jan 1, 1998

By R. L. Lewis

A simple method for estimating the steady-state water quality of a pit lake is presented. The steady-state concentration of a conservative chemical constituent in a pit lake is shown to be a simple function of inflow rate, evaporation rate, and inflow concentration. An analytical method is presented for estimating the equilibrium ground water inflow rate for use in water quality predictions. The time required to reach chemical steady-state is estimated using an iterative mass balance model. Mine operators should find the methodology useful for planning and screening-level regulatory applications where conservative estimates of pit lake water quality are desirable.

Jan 1, 1998

By Courtney W. Shea, Dennis Clark

Reckless blasting can have tragic consequences: The death of an innocent traveler, the financial demise of a coal company, and even criminal prosecution. In June 1993, a Tennessee coal mining company was blasting to loosen overburden at its surface mine. The mine was located immediately adjacent to the right-of-way of the northbound lane of Interstate 75. The approved permit included special precautions to be taken when blasting in the area closest to the interstate, including monitoring traffic so as to blast when the northbound lane was clear.

Jan 1, 1998

By Y. Maeda

Kosaka Smelter is a copper smelter located at the nothern part of Japan? and has been treating. complex sulfide concentrates using flash smelting technology for a long time. The flash smelting technology has an advantage in the point of controllability of matte grade and heat balance in the reaction shaft. But the disadvantage of this process, is that the dust generation ratio is high compared with other smelting process such as injection smelting technology. This reason why is that the flash smelting process is the oxidation process for the fine sulfide concentrates applying flash reaction in the oxygen enriched stream In addition of this disadvantage, the sulfide concentrates contains much volatile impurities is resulted the dust; eneration ratio more. This paper outlines the recent improvement of the flash reaction in the furnace and the behavior of impurities in Kosaka Smelter.

Jan 1, 1998

By Takeshi Ohgai, Hisaaki Fukushima, Tetsuya Akiyama, Joon-Seo Ki

"Recently, an intensive attention has been paid to the electrodeposition of Zn-Cr alloy in the field of the production of super-highly corrosion-resistant alloy plated steel sheets for the next generation. In this study the electrodeposition of Zn-Cr alloys from the sulfate baths was conducted to investigate the codeposition mechanism of Cr with Zn. As a result, Cr was codeposited with Zn at higher current densities in both polyethyleneglycol(PEG)-free and PEG- containing baths. However, PEG made it possible to reduce Cr+ to the metallic state and Cr existed in the form of Cr(III) hydroxide in the deposits obtained from PEG-free bath. The measurements of the partial polarization curve of Zn and the pH in the cathode layer revealed that PEG acted as a polarizer to shift the cathode potential to the reduction potential of the composited hydroxides of Zn and Cr formed due to the pH rise in the cathode layer.1. IntroductionRecently, much attention has been paid to the electrodeposition of Zn-Cr alloys because of its application to the production of super-highly corrosion-resistant alloy plated steel sheets for the next generation1Hl_ Some researches have already tried to commercialize this type of steel sheet. High corrosion-resistance of this steel sheet is brought about by codeposited Cr in the alloys. According to Piontelli's classification5l concerned with metal deposition from aqueous solution, Cr belong; to an inert metal and its deposition is associated with a large amount of hydrogen evolution. Therefore the current efficiency for Cr deposition is extremely poor. It has been also reported that Cr is unable to codeposit in the electrodeposited Zn film in the absence of a certain additive in the solution. 0-compounds group colloids7l, ether group organic compounds8), 9>, peptide based compounds10l, etc., have been found to be effective additives to induce the codeposition of Cr with Zn. However, few studies have been made on the codeposition mechanism of Cr with Zn. In this research, the fundamental electrodeposition behavior of Zn-Cr alloys from sulfate baths was investigated to clarify the codeposition mechanism."

Jan 1, 1998

By Vadim J. Jabotinski

This paper describes several areas of application for electron beam processing of materials. The technology and use of electron beam systems in gas phase synthesis reactions are described. Gas phase reactions may be used to generate ultra- fine metal or ceramic powder that are very pure and crystalline. Among the examples presented are: the generation of nanometer sized metal powders and the gas phase synthesis of silicon carbide for silica and methane. The experimental system is described and future theoretical and experimental objectives are identified.

Jan 1, 1998

By Toivanen R-M, Leinonen O, Pekkarinen H

This paper presents developments in designing an integrated mine control system at Kemi mine. The aim of this paper is to present the general structure of the system and to outline some features of the process control strategies. The results o

Jan 1, 1998

By D. W. Gunkle

Processing of various ores and materials in a reducing atmosphere has been done for many years. However, the typical device currently used is a large, often high maintenance, expensive piece of equipment; the rotary kiln. While it is a very reliable and a proven technology, the rotary kiln also has its limitations. It is limited by its ability to process very fine materials without creating a huge dust loss to the air pollution control equipment. This leads us towards the development of an alternate technology; the Gas Suspension System. Gas suspension preheating of various materials has been in commercial use since the early 1950's, but recently has been expanded to include Gas Suspension Reduction. Laboratory experience has proven successful on several materials; Nickel Laterite Fines, Iron Ore Fines, Fluorspar, and Clays. The gas suspension reduction system has many advantages over the conventional reduction kiln when processing fines. They are; lower cost, more fuel efficient, able to process fines, less real estate required, etc.

Jan 1, 1998

By Patricio Barrios

In February 1996, ATLANTIC, COPPER completed the construction of a Project for Expansion and Environmental Improvements in its Smelter and Electrolytic Refinery located in Huelva. Following the expansion, the new operating concept is based on the simultaneous blowing of two converters, while increasing throughput in the Flash Furnace up to the level required to deliver matte to both converters. While the production level planned with the Project.(270,000 MTPY of copper from concentrates) was reached the following June, work since then has been carried out to optimize the new equipment .and to develop a new operating shedule. This paper describes operational experiences from the start up of the Expansion Project, difficulties encountered and operating improvements introduced, which have allow an increase of production levels up to 300,000 MTPY of copper.

Jan 1, 1998

By Garry Biles, Ken Major, Raj Anand

"Prime Resources Group Inc. (Prime) commenced the Eskay Creek Mine operations in 1994 in northern British Columbia. The ore from the underground mine is crushed and shipped to smelters in Japan and Canada. The nominal production rate is 300 tonnes per day.Before commencing the above operations, preliminary evaluations for the high grade gold mine had indicated that an extremely complex metallurgical and chemical process flowsheet would be required to recover the economic metals. Subsequent to the metallurgical testing program, Prime identified markets for the untreated ore and initiated underground mining and ore transportation operations.Prime recently identified lower grade ore zones, which are less economic or uneconomic to mine and ship directly to the smelters. Test programs were initiated to evaluate processes for upgrading the ore to a marketable product. In 1997, Prime will complete the engineering and construction of a 150 tonne per day flotation plant to concentrate the gold and silver values for the NEX and 109 zones. The mine will then, in addition to the direct shipping of the shippable ore, ship concentrate from the millable ore. This paper discusses the development and design of the flotation plant.IntroductionThe Eskay Creek Mine is located in north-western British Columbia approximately 83 km north-west of Stewart, B.C. as shown in the location map Figure 1. Access to the site is provided by a restricted access gravel road from Bob Quinn Lake junction of highway 37, a distance of about 59 km. The work force at the mine is based on a two-week rotation schedule. Employees are flown from as far away as Vancouver to Smithers by commercial airlines and then from Smithers to the Bob Quinn airstrip by local charter. During poor weather conditions, transportation to site is by vans that take about six hours to travel the 450 km road distance."

Jan 1, 1998

Longwall mining in Australia is approaching maturity. Longwall production from 'state of the art' Australian longwall mines now rivals similar US based longwall operations. Regrettably however, Australian gate road development rates in general fall short of the required development to longwall production ratios that are required to sustain annual longwall production capabilities. By contrast, most US based longwall mines achieve the required development to longwall production ratios to sustain their longwalls. This is despite many having to drive three heading longwall panel gate headings to meet regulatory requirements.

Jan 1, 1998

By David M. Spatz

Team, as defined by Katzenbach and Smith (1993), is a small number of people with complementary skills who are committed to a common purpose, performance goals and approach for which they hold themselves mutually accountable. As the mining industry searches for new ore discoveries increasingly under post-mineral cover, the process of mineral exploration has taken us from prospector to geologist to multidisciplined explorer to multi-disciplinary team. Multidisciplinary exploration techniques have improved in terms of sensitivities and penetration and more than ever before each technique requires specialists with appropriate training and skills to process data and interpret results. To produce a quality product, specialists must collaborate openly and honestly in an atmosphere where the collective result takes into account the knowledge and expertise of each individual and the relationships between all pertinent data sets.

Jan 1, 1998

By Marian W. Otrebski, Julian A. Korneck

Long distance, overland conveyors require significant capital outlay of which up to 70% may be contributed to the cost of belting. Significant savings may be achieved by identifying possible risk areas and applying modern technology methods to reduce or eliminate risk. Recently, Sasol Coal commissioned an overland belt conveyor system comprising three belt conveyors of 7 km, 5 km and 4.5 km in length. These were designed and constructed taking the above into consideration. Contained in the paper are the belt conveyor system requirements, designing assumptions and methods applied in the designing process as well as ways and means to eliminate or at least reduce risks.

Jan 1, 1998

By Jack Eloranta

"This paper compares energy requirements for blasting, crushing and grinding. By tracking electricalconsumption for various powder factors, a general trend has appeared. This study involved over 100million tons of ore and powder factors ranging from .5 lbs/L,T to .8 lb&T. Actual energy usage iscompared to predicted energy based on the Bond equation."

Jan 1, 1998