Search Documents

By Tom Denton

The bolt design criteria, since it was first published by Dr. John Stankus (Stankus, 1997), has been recognized as an important tool in ground control design. This concept is based on the Optimum Beam Building Effect (OBE), which is defined as the roof beam that has no separation above or within the bolted range and having the shortest bolt possible. This paper will present an application of this concept at the American Coal Company. Galatia mine. This mine previously used a 6' and 7' length bolt. However, since seam thickness has gotten smaller in the Southern area of the nine, a two-piece bolt is required. A two-piece bolt increases ground control costs and delays production. Therefore, a one-piece, shorter bolt, if feasible, can reduce costs and expedite development. In this analysis, Computer modeling is first conducted to determine bolt length and installed load. Second, a special bolt is developed, that can achieve the proper installed load as determined by the computer modeling. Third, underground bolt pull and load cell tests were conducted to evaluate bolt performance. Finally, an underground "bench" test was conducted. The test results have shown that entry convergence in the short bolt (5) test area is less than the 6' bolt area. Overall roof condition in the test area was as good as the 6' bolt area. Based on this analysis, the mine has converted to a shorter bolt in the low seam area and it is working well.

Jan 1, 2000

By K Nesbitt

Draw control at Premier Mine is considered important to avoid conditions of isolated draw, which results in early waste ingress, compaction of the kimberlite ore and loss of ore reserves. The Premier Mine kimberlite pipe is unique in that the pipe is cut at a depth of 400 metres below surface by a 75 metre thick gabbro sill. All cave mining at Premier is below the sill and failure to exercise good draw control could cause early ingress of gabbro waste. Gabbro causes problems in the diamond recovery plant and the amount of gabbro sent to the plant needs to be closely monitored. Fortunately coarse gabbro fragments are easy to recognise in drawpoints. It was anticipated that only 85 per cent of available ore would be drawn from the blocks immediately overlain by the gabbro sill before excessive gabbro waste forced the closure of drawpoints. Data on tons drawn per drawpoint and loaded per LHD as well as the tons tipped per pass is gathered by the vehicle monitoring and control (VMAC) system and information recorded by the load-haul-dump (LHD) drivers. Draw control staff monitor drawpoints on a shift basis and record the occurrence, type and height of hang-ups. Information pertaining to the status of the drawpoint in terms of support, waste and availability is also recorded. A database has been compiled that has been used to analyse the overall pattern of draw control, the frequency of occurrence of different types of hang-ups, secondary blasting efficiencies and drawpoint and LHD productivity. The gabbro sill has provided a unique marker horizon that has allowed the arrival of rock from a level 100 metres above the production level to be recognised. Data shows that ore migrates extensively towards groups of drawpoints that are heavily drawn with many drawpoints more than 100 per cent drawn before gabbro waste was recognised. This indicates that an accurate mixing algorithm is essential for good draw control. Data on tons drawn, drawpoint availability, productivity and the occurrence of various types of hang-ups has allowed better control of the mining operation and provided data for planning future caves. In the BA5 mining block a drawpoint spacing of 22 metres, horizontally across the major apex, has still allowed drawpoints to be pulled to waste with no loss of ore. In the BB1E mining block the drawpoint spacing has been increased to 23 metres and no problems have been experienced to-date. Future initiatives centre on improving the data gathering integrity of the vehicle monitoring and control system and a linear programme that will optimise draw control and productivity.

Jan 1, 2000

By Steve Collinsworth

Sometimes, for those of us in the right place at the right time with the right product, necessity creates opportunity. Such is my case at a West Virginia coal mine where a mine manager was desperately seeking a way to eliminate coal damage on cast shots while maintaining cast percentage without the expensive process of secondary drilling. This paper will focus on how bottom hole air decking is solving the problem.

Jan 1, 2000

By E. Gervais

Modern life in inconceivable without zinc. Zinc provides the most cost-effective and environmentally efficient method of protecting steel from corrosion. Zinc is also used to power electric vehicles and computers, to make brass, automotive equipment, household appliances, fittings, tools and toys, and to support the building and construction industries. It is also used in pharmaceuticals and cosmetics, in rubber, in fertilisers and in animal feeds. The links between properties, applications and performance, as well as zinc demand and market dynamics, will be reviewed along with market development opportunities and successes. The presentation will also include a progress report on the five-year plan of the International Zinc Association to increase the global market for zinc, over and above the natural growth, by 500,000 tonnes/year by 2002.

Jan 1, 2000

By Mituo Tougo, Mitsuo Tokunoh, Takayasu Kisaragi, Fuminori Chiba

We have about 200,000 tons/year of dross residue produced after the collection of aluminum from the dross generated during the aluminum remelting process. 130,000 tons of the dross residue is used as a steel deoxidant or a cement material, and the remaining 70,000 tons is abolished and buried in the ground at authorized places. The dross residue is increasing along with the increase in the aluminum production. This situation will grow more serious with a large amount of aluminum window sashes which have been mass-produced since 60's and will return before long as scraps. Our effort is being directed to the development of technologies which enable the dross residue to be recycled and reused for some purposes such as road aggregates, refractories and others, in such a way as to comply with the social requirement which gives prfority to the recycling industry, as well as to the environmental preservation.

Jan 1, 2000

By T. P. Weldum, B. J. Mahoski, R. S. Rasmussen

A case study of a systematic approach to grinding circuit steady-state optimization is presented. After an overall review of the flow-sheet, two operating circuits were prepared for detailed testing. Functional performance analysis was chosen as the primary modeling system, and, on this basis, a quality-assurance program for data gathering was implemented. A number of circuit-design and operating variables were investigated. Statistical analysis of plant-test results revealed relationships previously unquantifiable by any other modeling technique. Improvements in the classification system and in mill grinding efficiencies were demonstrated. As a result, there was significant energy cost savings.

Jan 1, 2000

By C. Mattich, A. L. Beyzavi

The Waelz Plant at Taiwan Steel Union Co. Ltd. (TSU) was erected within nine months from September 1, 1998 to May 15, 1999. The nominal capacity of the plant is 50,000 tonnes per year of electric are furnace dust (EAFD). The plant, consisting of material handling, a waelz kiln, a waste gas cleaning system, waelz oxide leaching and waste water treatment, was commissioned within three months from July 1, 1999 until October 12, 1999. The specific problem of the plant is the high chlorine content in the EAFD pellets which is up to 6 %. Lurgi Metallurgie GmbH, Frankfurt, Germany was responsible for the engineering erection and commissioning of the plant.

Jan 1, 2000

By Denis Legault, Ghyslain Dube, Ronald Morin, Jacques Bonneau, Daniel Guay, Keith Annett, Raymond Breault

"·The total recycling of all the constituents present in aluminum dross is now an industrial reality for Akan. This is made possible by the combination of two patented processes: the Alcan plasma dross treatment process, operating since 1990 at its Guillaume-Tremblay Works, and the calcium aluminate fabrication process, operating at AlumiCa's new plant in Thetford Mines. The latter process uses the total non-metallic content of the dross, thus rendering possible the complete recycling of aluminum dross.After describing the plasma dross treatment process, this paper will present the calcium aluminate fabrication process and how both processes contribute to close the recycling loop. The characteristics of Nova!™ by-product will also be described, as well as how they contribute to make a calcium aluminate with chemical and physical properties that are highly sought after. This calcium aluminate, produced by AlumiCa, is marketed under the trade name Kwikflux®. AlumiCa's total production is presently sold to a number of steel plants worldwide."

Jan 1, 2000

By Raymond A. Binns

Drilling into an active hydrothermal system linked to convergent-margin felsic magmatism is a listed priority of the Ocean Drilling Program that addresses several fundamental geoscience issues. Solid and fluid products of felsic rock-water interaction, and the consequences for global chemical fluxes and for ore deposition, should differ from those in basaltic mid-ocean ridge environments already successfully tested by Legs 106, 139, 158 and 169. So, too, will fracturing controls on fluid pathways, and sources for metals and ligands. Researching the subsurface volcanic, structural/hydrologic, and mineralisation/alteration architecture of a drilled felsic-hosted system also has economic implications, especially for land¬based mineral exploration. A first-order hypothesis to be tested states that fluids derived from volatile-rich magmas are more important than recirculated seawater in convergent-margin hydrothermal systems - economic geologists increasingly appeal to this for creating "world-class" massive sulfide orebodies. Another hypothesis proposes "subhalative" massive sulfide deposition within hydraulically expanded volcanic products as a factor in generating large orebodies. Many second-order hypotheses such as leaching fractionated volcanics to cause gold enrichment in back¬arc systems also need testing. The thoroughly surveyed, active, PACMANUS hydrothermal field in the Eastern Manus back-arc basin of Papua New Guinea will be the site for ODP Leg 193 commencing in November 2000. It lies near the crest (1655-1750 m) of high-standing Pual Ridge, a 40 km-long edifice of dacite/rhyodacite with basal andesite all having geochemical and isotopic affinities with modern arc volcanoes of nearby New Britain. PACMANUS includes at least three focussed, high-temperature "smoker" sites with Cu+Au-rich massive sulfide deposits, and a field of diffuse, lower temperature venting through intensely altered dacite where modelling indicates significant subsurface mineralisation. Isotopic characteristics of deposits and vent fluids suggest magmatic contributions to the mineralising fluids.

Jan 1, 2000

By D Mukendi-Ngalula, G Hearn

Beach sand minerals from the volcanic rock structures of the Drakensberg, Kwazulu-Natal, (South Africa) have been processed. Screening, flotation, spiral concentration and magnetic separation methods were used either separately or successively in an attempt to concentrate monazite minerals. Products thereof and those from a long time (up to 72 hours) microwaves treatment of the finally produced ilmenite-bearing minerals have been studied using the M÷ssbauer effect spectroscopy. The 57Fe M÷ssbauer effect spectroscopy has demonstrated its versatility and power in monitoring the ilmenite internal reduction mechanism and products and, in characterising the iron-bearing phases contained in different products from the beach sand minerals processing. Microwaves heating of ilmenite for up to 38 hours reduced internally the Fe3+ from the ilmeniteÆs structure. A more prolonged microwaves heating (up to 72 hours) re-oxidised the mineral. 61 per cent natural ilmenite recovery was obtained in the floating products of a spiral concentrated -212+106 ¦m screened and beach sand minerals fraction. A preferential concentration of hematite with a 62 per cent recovery was found in the sinking products while the combination of screening-spiral separation-magnetic separation and flotation yielded a floating product with the highest ilmenite and the highest hematite abundanceÆs (71 per cent, 19 per cent respectively). A natural ilmenite containing 87 per cent ilmenite and 13 per cent hematite could be produced and extracted from the sinking products of the flotation process collected subsequently to the spiral concentration and the initial screening.

Jan 1, 2000

By G. Ansong, P. K. Achireko

The authors present a new mineral price model, compare it with time series and naive models, and analyze the effects of the forecasting models on mineral project evaluation. Mineral commodity prices are volatile, which means that the results of evaluation tools that do not treat the stochasticity of metal prices rigorously may be misleading. But, in mine valuation, commodity price forecasts are required to assess the economic viability of a project. In this study, a new mineral forecasting method, called the MNDRVG-MFNN-RM model, which incorporates randomness, neural networks and regression models, is introduced. The MNDRVG-MFNN-RM model, a naive method and time series model were used to forecast gold prices for two successive years for the evaluation of a proposed open-pit mine. The MNDRVG-MFNN-RM model yielded the best results among the three methods. It produced the true optimum pit limits and an optimum pit value slightly less than the true optimum value. The main novelty of the methodology is the simulation and rigorous analysis of the randomness property associated with mineral prices to reduce the estimation and forecast errors, an important contribution to mineral venture evaluation, mine planning and design.

Jan 1, 2000

By Caroline B. Chapleau, Mélanie Proulx, Claude Bazin, Gaétan Lavoie

"Quebec Cartier Mining operates a pelletizing plant in Port-Cartier, QC. Grinding, agglomeration and pellets induration are the three main steps in the preparation of iron oxide pellets. In 1998, following different recommendations, the company increased the speed of one of its ball mill in order to increase the grinding efficiency of the machine. As expected, the increased speed lead to an increase of the power draught, which did not produce the expected increase of fineness of grind, neither its allows to increase the mill throughput. The change of behaviour of the mill could hardly be understood by comparison of discharge size distribution at initial and modified mill rotation speed. On the other hand, the use of the selection function from a population balance model provides an insight of the changes that occurred in the mill. This paper reviews the various steps required for the estimation of a grinding mill selection function. Results of the calibration to Quebec Cartier grinding mills show that the increase in the mill speed leads to higher rate of breakage of coarse particles, at the expenses of less efficient breakage of medium and fine size particles. In the case of the studied mill, breakage of coarse particles was probably not the critical step of the mill operation. INTRODUCTIONOre size reduction is the major energy consumption step in any mineral processing operations (Austin et al., 1984). Size reduction is required to either liberate valuable minerals from the gangue minerals in which they are imbedded, or to increase the specific surface of the ground material. Plant engineers continuously face the challenge to find grinding machines, operating conditions or grinding circuit flowsheet configurations that could improve the size reduction process at lower energy or m6dia consumption."

Jan 1, 2000

New Zealand depends on foreign investment for economic development. This also applies to the development of New Zealand's mineral resources. For this foreign investment to happen there must be some incentives to attract the investment. While prospectivity is the dominant parameter considered by investors it is not a variable that can be changed, only the perception of New Zealand's prospectivity. Other parameters likely to be considered are sovereign risk, red tape, green tape, land access, civil unrest, land claims, social risk, labour relations, infrastructure and natural disasters. Regulators and political will can vary some of these parameters. Where New Zealand fits internationally can be measured by investors' perceptions of these parameters. Following on from these perceptions New Zealand can be seen to have advantages in some areas and be disadvantaged in others. How to deal with the disadvantages to give investors confidence is not easy in the New Zealand environment where the development of mineral resources plays a small part in an economy dominated by agriculture. Added to this is the current global state of the minerals industry which offers even more of a challenge to attract foreign investment to develop New Zealand's mineral resources.

Jan 1, 2000

By A. Rohkohl, R. Piillenberg

The QSL plant at "BERZELIUS" Stolberg GmbH in Stolberg, Germany was commissioned in 1990, introducing a new era of lead smelting in the more than 150-year-old history of the lead smelter. The lead smelter in Stolberg has changed its appearance several times during its existence. Therefore, at many locations on the site, old and obsolete buildings and equipment parts can still be seen. They are often located side by side with new modern constructions like the QSL-plant and the mercury removal plant, and reflect the specific contrast between tradition and modern technology. After a brief description of the development of the smelter and its decision to implement the current novel plant, the most recent operating results are reported. Following some modifications to the process and equipment, which had become necessary along with the implementation of the new technology, the plant is in operation today at approximately 30% above its design capacity. These achieved production levels are not restricted by the QSL-reactor but by precedent and subsequent available equipment. The QSL-plant entirely complies with the demands of modern, energy-saving, ecologically compatible lead production technology. Stringent environmental standards are maintained on a continuing basis. The demonstrated viability and flexibility of the overall process permits the operation to adapt quickly to the prevailing economical situation worldwide.

Jan 1, 2000

It is proposed to consider a new access, mining and hoisting system for underground deposits, as an alternative to the commonly used decline or vertical shaft access. The proposed system offers fundamental improvements in gathering of exploration data, reduction of capital expenditure and significant savings in mine operating costs. The cost reductions are achieved through:superior orebody definition by Supersucker winzing on ore prior to the commencement of capital development; considerable reduction of capital development in waste; full capitalisation on all benefits of a raisebored excavation; introduction of rubber tyred skip and rubber tyred Mine Rapid Response Vehicle; introduction of simplified ore handling system and reduction of underground mobile diesel fleet; and introduction of minimum maintenance shaft concept. The system is applicable to deposits ranging from shallow, low dip angle, narrow vein, high-grade to bigger, massive type vertical mineralisations accessed from the surface, preferably from the bottom of an open pit; it is also suitable as a down dip extension of an existing underground mine. The system is highly conducive to mine automation and emerging trend aimed to increase the ratio of mined metal/mineral to mined waste. It offers substantial reduction in diesel exhaust gas emissions to the mine atmosphere.

Jan 1, 2000

By S Grano, J Ralston

Selective oxidation of minerals was used in this study to separate by flotation the copper sulphide minerals of chalcocite, covellite and chalcopyrite from the arsenic copper sulphide minerals of enargite and tennantite. It was found that a satisfactory separation of these minerals was only possible after selective oxidation of their surfaces in slightly acidic pH conditions, or after oxidation and selective dissolution of the surface oxidation products with a complexant in basic pH conditions.

Jan 1, 2000

By B. R. Baldock, R. W. Matusewicz

The recycling of used computer boards is a key industry activity for the recovery of precious metals. The safe and effective separation of metallic from non-metallic materials and subsequent processing of these secondary materials to provide high recoveries of values and excellent environmental performance are critical process requirements. Ausmelt Technology has been used commercially in four plants for the recovery of precious metals and has also been used very successfully at pilot plant scale to process computer boards. This work and its application to commercial operations with particular reference to processing conditions and environmental performance are reviewed.

Jan 1, 2000

Geophysics is playing an increasingly important role in the exploration industry. In the soft rock scene the application of seismic techniques is basically mandatory prior to any drilling program. Simply, this is because, in a majority of situations, the seismic method is ideally suited to mapping accurately relatively flat lying strata and displaying structures that may host oil or gas. It is worth stressing that seismic methods do not delineate oil or gas but they map well in two or three dimensions. In the base metal arena, geophysical methods used are generally focussed on direct detection methods with the mapping application not often used except in potential fields (magnetics and gravity). The success rate in the last decade has not been good but this does not only apply to the application of geophysics; it really applies across the board of exploration techniques. Both geological and geochemical exploration have not had a success rate commensurate with the funds injected. Basically in the last ten years we have failed as explorers! As explorers we have been negligent in mapping. As geoscientists we have let the basic mapping and observation skills diminish û the old adage æboots on the groundÆ is still applicable but are we doing enough of it? The answer is clearly no. As explorers the huge burden of bureaucracy, eg Government Acts û local, state and federal, safety compliance, environmental compliance, etc has reduced the ægeologicalÆ time dramatically. This has culminated in an over-reliance on quick fix solutions, eg spot the bump geophysics or geochemistry. This obviously simplistic scenario is arguable but there is no doubt in the geoscientific areas we have failed in the last decade to provide adequate geoscientific maps to assist in exploration. This failure could partially be responsible for the current demise of the industry resulting in a reduction in exploration dollars and, hence, people. This trend is seen acutely in the geophysical area where the head count in comparison with the geological fraternity is low. Other trends during this downturn are inevitable as explorers maximise the use of the dollar in exploration and diminish spending on advances in geophysics. Improvements are being seen however in geophysical equipment, although it is considered that the main improvement will be in the interpretation of data. Specifically, the trend will be towards integrating geophysical data into geological, geochemical and spatial data sets producing quality interpretation and providing low risk drill targets. Examples of the current trends in hardware and future directions are discussed below. In interpretive schemes there are very few examples of integrated interpretation but the possible trends will be discussed with limited examples.

Jan 1, 2000

By Hamid Maleki

Results of geologic investigations, in-mine instrumentation, and numerical modeling are presented for two longwall mines in which pillars with large width-to-height ratios (8 to 9) are used. These investigations revealed that wide pillars unload when subjected to sufficient stress and that pillar unloading is influenced by geologic conditions. Field measurements in mine 1 clearly indicated load transfer from the longwall area toward the gate roads, resulting in pillar failure near the margin of a fluvial channel. Loads were shown to transfer to a harrier pillar (width height ratio equal to 9), contributing to progressive failure of this pillar. Unloading of the barrier pillar was associated with significant load transfer to the two-seam submains to the north of the harrier, contributing to roof falls, floor heave, and rib spalling within the submains. Stress analysis results addressed pillar peak strength and unloading behavior that was in agreement with the measurements and underground observations. Underground observations and stress analyses were completed before and after longwall mining near a six-entry submain in mine 2. This submain was intended to he used as a temporary bleeder and tailgate for a small longwall block consisting of one to two panels, depending on the development schedule in other areas of the trine and observed ground conditions. Numerical modeling using both elastic and inelastic pillar behavior for submain pillars with a width-to-height ratio of 8 was completed before mining began. Results indicated that pillar unloading was likely. During retreat of the first longwall panel, pillars unloaded. as evidenced by progressive rib spalling along the cleats, This behavior was mostly confined to the immediate face area, an observation that was in agreement with the modeling results,

Jan 1, 2000

By Shigehisa Endoh, Hitoshi Ohya, Atsushi Inaba, Shigeki Koyanaka

"Recycling should be promoted to keep the global environment. However, it is difficult to detennine the quantitative impact. A life cycle assessment is one of the most reliable methods to estimate the global environment impact.Exergy is useful like entropy when considering the sustainable development. All of our activities have been obtained exergy resources and/or energy itself and throw away waste and/or waste heat. We are trying to use exergy to estimate the quantity of energy and matter for resource accounting. For recycling plastic, plastic has two aspects; material and energy source.The environmental assessment of plastic recycling suggests that the exergy reduction of the entire system is estimated by the yield of matter and the process efficiency. The material recycling is better than the thennal recycling when the process efficiency is high. However, the thennal recycling is much better for the low efficiency. The transition point is able to be decided by the efficiency of the manufacturing and the electric power generation.IntroductionRecently, many of the global environmental problems have become conspicuous like global wanning, ozone layer depletion and acid rain. Some of the methods like life cycle assessment for solving these problems have been presented. Anxiety concerning the proble1ns of energy and resources has led to a rapid increase in the interest in describing and understanding the conversion processes of energy and other resources in today's society. All human activity is supported by obtaining power and products of high exergy from the environment and throwing away the waste material and the waste heat of low exergy back the environment. However, the total exergy in the whole system becomes absolutely smaller than before.The rate of obtaining high exergy products and energy itself by human activity and the speed, by which waste and waste heat having low exergy are thrown away are too fast to attribute to environmental problems [1-3].A material's use by recycling was often common in a circulating society mainly. A significant amount of energy is consumed during circulation. An environmental impact assessment method for the process or the system has not been devised when both of them are taken into consideration. Even if the life cycle assessment evaluation, which has been correctly used up to now, is applied, it is not sufficient for an overall evaluation concerning matter and energy.The real sustainable development is that the exergy reduction value by all human activities on the earth is kept within the range of the exergy reduction in order to consider the earth as closed stationary system. It is important to evaluate the process or the system by using the exergy, and design them so that the exergy loss may decrease as much as possible. We have to consider what process improvement is the most effective."

Jan 1, 2000