Search Documents

By B. Caldwell

"The CompanyCardinal River Coals is jointly owned by Luscar Ltd. and the Consolidated Coal Company of Canada (Consol). The Luscar mine is operated by Luscar Ltd. and is located 40 km south of Hinton near Cadomin, Alberta (Fig. 1). The plant sits on the old townsite of Luscar, Alberta, which was founded in order to develop the coal in 1912 (Fig. 2). Initially, the coal was mined by Luscar Ltd. for heating and steam generation and used quite heavily by the railways for their steam locomotives. In 1955, the mine was decommissioned as the demand for coal for tl1ese purposes had dropped off. In 1969, the mine was re-established by Cardinal River to provide metallurgical coking coal for its customers in Japan. The coal is mined from the 13m thick Jewel Seam by open pit methods at a 10 to 1 stripping ratio. The run-of-mine coal is then cleaned to meet customer demands.The PlantThe clean coal preparation facilities at Cardinal River were extended in 1980 in order to increase the feed rate from 450 t/h to 800 t/h. The extension is a separate plant which can be operated on its own or in parallel with the old plant. In addition, modifications have been made to the fine coal circuit (hydrocyclones added), the coarse refuse circuit, (refuse bucks replaced by a refuse conveyor which backfills a pit), and the fine refuse circuit (solid bowl refuse centrifuges, refuse classifying cyclones, and hydra-rake thickener no longer utilized) since the plant was built in 1969. The plant production of 3 M t per year with a yield of 78% is achieved by first screening and breaking the run-of-mine material to a top size of 1 ½ in. The feed is then slurried, sized, and processed in three different washing circuits. The washed coal is mechanically dewatered, thermally dried, and then stored in a 14 500 t capacity silo or on a 300 000 t stockpile. The fine refuse is thickened and pumped to the same pit to which the coarse refuse is being conveyed"

Jan 1, 2000

By K. Murayama, M. Kawakami, T. Takenaka, S. Yokoyama

"Cokes play an important role of spacer in blast furnace. However, they degenerate during Boudouard reaction. Blast furnace cokes are reacted with pure C02 at I 072 to 1673 K. Reaction rate was obtained by the weight change of spherical specimen. The specimen after reaction was examined by microscopic observation. The reaction rate increased with temperature and was expressed by two Arrhenius type lines. The activation energy was 126 KJ/mol at higher temperature than 13 73 K and 202 KJ/mol at lower temperature range. At the higher temperature range, the reaction proceeded from the surface leaving unreacted core, whereas homogeneously whole inside at lower temperature. The porosity increased from the center to surface at higher temperature, whereas it was almost constant at lower temperature.IntroductionThe cokes have the function of fuel, reductant and spacer to keep gas and liquid flow in the blast furnace. Thus, the reaction mechanism of coke with several gas and the strength after the reaction should be important factor to control the blast furnace operation. The reaction mechanism of coke with C02 has been studied extensively. The rate equations were derived by Gadsby[ I], Ergun[2] and Turkdogan and Vinters[3]. They were compared and discussed by Kobayashi and Omori [ 4]. Effect of crystallization degree on the reaction rate was examined by Kashiwaya and Ishii[5]. Catalytic enhancement effect of ash componets have been clarified by Kashiwaya et. al. [6]. Although degradation of coke in blast furnace has been examined recently[7], however, the degradation of coke after the reaction with C02 has not been well clarified yet. In the present work, the metallurgical coke specimen was heated in N2 and C02 and the reaction mechanism and degradation behavior after the reaction was investigated."

Jan 1, 2000

By W J. Rankin

A study of refined metallic copper and nickel production was carried out using Life Cycle Assessment methodology to estimate the life cycle emissions of greenhouse and acid rain gases for these metals using data derived from the literature. Various processing routes were investigated which included a pyrometallurgical and a hydrometallurgical route for each metal. The effect of a number of process variables, namely ore grade, fuel type for electricity generation and efficiency of generation were also examined in the study. The results of the study, expressed in terms of total (or full cycle) energy consumption, Global Warming Potential (GWP) and Acidification Potential (AP), showed that the hydrometallurgical processes involving solvent extraction and electrowinning had higher energy consumptions and GWPs than the pyrometallurgical processes for both metals. Nickel metal production was shown to be several-fold more energy intensive than copper metal production. The significant effect that falling ore grades have on attempts to meet greenhouse emission targets was also highlighted in the study.

Jan 1, 2000

By J. F. T. Agapito

OCI Wyoming mines two flat-lying trona seams that are 3- to 3.5-m- (10- to 11.5-ft-) thick, about10 m (33 ft) apart and 250-m- (820-ft-) deep at its Big Island Mine in Wyoming. Continuous miners and a yielding-pillar system have contributed to improvements in resource recovery and productivity. The use of yield pillars minimizes the stresses transmitted from the upper to the lower seam. However, yielding must not impact the good, long-term stability needed to prevent subsidence for a large portion of the mine beneath the Green River channel.

Jan 1, 2000

By J. L. González-Chávez, A. Ballester, M. L. Blázquez, F. González

In recent years, the bioleaching of sulfidic raw materials has been of great interest. However, the application of this biotechnology is now very limited for many different complex reasons. The mechanism of the chemical and electrochemical reactions taking part in the process is not well understood. The application of electrochemical techniques is useful in its elucidation. Among the common sulfides, galena has been studied very little with respect to its behavior during bioleaching. Therefore, the electrochemical evolution of massive electrodes of lead sulfide in the presence and absence of' a mixed culture of mesophilic microorganisms was investi¬gated by the application of potentiometry, anodic and ca¬thodic polarization and cyclic voltammetry. The agitation rate, the use of pH control and the composition of the nutrient mediums did not have any significant affects on the oxidation of galena. However, the temperature (25 'to 45 °C), the scan rate (4 to 100 mV/s) and the acid used to adjust the pH were significant variables that influenced sulfide oxidation. There¬fore, the peak (600 to 1,000 mV) corresponding to the oxida¬tion of sulfide ions from the mineral was only detected in the presence of a complexing anion of lead. In the presence of bacteria, the peaks corresponding to galena oxidation de¬creased and, at the same time, new peaks appeared both during the oxidation at -300 mV and during the reduction of the mineral surface at 150 and -300 mV. These signals were more important when the attack time increased. The rest potential of bioleached mineral increased with an increase in leaching time, which was related to the electrochemical transformation of the galena surface.

Jan 1, 2000

By P Murthy, Z Guan, P Townson

In this paper, we introduce a methodology to optimise mining equipment operation in terms of the conflicting concerns of productivity and availability. We also introduce the concept of damage points and equipment dutymeters. These provide the mine management with tools to monitor the success of such optimisation. Since we have quoted the results of an on-going Australian Coal Association Research Program (ACARP) project, the apparent focus of this article is on draglines. However, the concept is equally applicable to other equipment. Mining is the type of business that requires a large investment in capital infrastructure and equipment to produce a product that is sold at a relatively low unit cost. In such a business, the key to competitiveness lies in achieving the full realisation of capital investment ie sustained production at high levels. Some of the concepts outlined in this paper are essential components of this picture.

Jan 1, 2000

By Larry M. Southwick

There is much ongoing work in research and development of new processes for the recovery and recycling of met.a.ls and other materials from various waste and scrap streams. Commercialization of such new technologies requires the bringing together and successful execution of a considerable effort involving a variety of activities. These include process conceptualization, research and development, detailed design and construction, and then plant startup and operation. Processes evolve through all of these steps by engineering due diligence, making objective and critical analyses of results, and troubleshooting processing steps to, hopefully, arrive at a sequence that has the best chance to succeed operationally and economically. After a summary review of the above steps, several processes will be described in more detail that provide mostly successful examples of the above procedures. Finally, some observations will be made on areas that will become critical in the near future to the success of new processes for wastes and residues.

Jan 1, 2000

By Takeo Fujino, Nobuaki Sato, Junichi Hasegawa, Masato Nakazawa, Kohta Yamada

"Tantalum oxide thin films were deposited on quartz substrates by laser ablation of Ta2O5 target using Nd:YAG pulse laser. Deposition-was observed when a laser light energy higher than 200 mJ and its repetition rate higher than 3 Hz. A thin film of 0.1 µm thickness was obtained by the ablation using a laser light of 300 mJ and 6 Hz for 2 sec. The thickness of the film increased with increasing energy, repetition rate and irradiation time of laser. By the SEM observation, it was found that many island-like particles were deposited on quartz substrate forming a thin film. The obtained thin film, which was identified as ? Ta-O by X-ray diffraction, was oxidized to Ta2O5 by the heat treatment in air at I273 K for 3 h.IntroductionTransition metal oxides have a potential to show special characteristics in electrical, magnetic and/or optical properties. When such compounds are fabricated in the form of thin film, the special properties would be improved or new characters would appear in comparison with bulk materials. Tantalum penta-oxide is widely used as a capacitor since Ta2O5 shows high dielectric constants up to high temperatures. The tantalum solid capacitor has been fabricated by the electrical oxidation of sintered Ta metal cylinder followed by MnO2 film coating. However, further improvements, reduction and layered structure formation, are required for compacting the devices. The layered structure of thin films would be applicable for the above requirements. The formation ofTa2O5 film by low pressure CVD1), photo CVD2) and magnetron sputtering3l were reported. The laser ablation -method is one of the most convenient techniques for the deposition of thin films from their compounds, such as oxides. Formation of Ta2O5 film by pulse laser deposition (PLD) method using ArF excimer4), Nd:YAG (533nm)5) and TEA CO2 6 lasers was reported. In these PLD studies, ablation was carried out in relatively high oxygen pressures resulting in formation of Ta2O 5 film. In this paper, the deposition of tantalum oxide thin film by the laser ablation of Ta2O 5 using Nd:YAG pulse laser was examined at a viliety oxygen pressures ranging from 10-8 to 10 Torr. The morphology of the films was also investigated in relation with substrate temperature and oxygen pressure."

Jan 1, 2000

By Daniel Hodouin, Antoine Berton

Mineral processing plants are monitored and controlled using measurements that are usually processed by on-line material balance calculation techniques. However, gross errors, due to sensor biases or failures, may corrupt all the process variable estimates. On-line gross error detection methods are required to ensure efficient mass balance evaluation. In the proposed approach, material imbalances and raw measurement corrections are tested by statistical techniques designed to detect and isolate sensor problems.

Jan 1, 2000

By V S. Svinin, V V. Rybin, V A. Maltsev

In large-scale mining, large-sized intermediate pillars, or block-pillars, are generated on the horizon or between closely located mines. These pillars are mined under high rock pressure that results from the stress concentration zones superposition from closely located working excavations. This problem becomes much more complicated if high tectonic stresses occur in the rock mass inducing a rock-burst risk situation. Mining experience gained in mining seven block-pillars at three Khibiny mines in Russia under the geomechanical situation like that described aboveÆ is discussed in detail. It has been shown how safe mine of block-pillars depends on their width, location relative to significant geological failures and uncaved rocks of the hanging wall, the order of pillar recovery, and application of special measures for rock mass stress relieving. Basing on the analysis of the mining experience and special scientific researches, the basic principles are worked-out for safe block-pillar mining under rock-burst prone conditions.

Jan 1, 2000

By Jerry Demchuk, Allan Flemming, Stephan Day

Luscar Ltd. is currently developing open pit mining plans for the Telkwa Coal Project. Most waste rock is predicted to be non-acid generating but a proportion (less than 20%) is potentially acid generating. The waste management plan includes in-pit and ex-pit disposal of blended and till-capped waste rock, segregation and in-pit encapsulation of strongly potentially acid generating materials, and in-pit underwater disposal of coarse and fine tailings. The paper will present the steps used to design the waste management plan including the development of geochemical design criteria using various tests and theoretical and practical knowledge of waste behaviour.

Jan 1, 2000

By V. B. Achanti, A. W. Khair

This paper deals with the effects of various bit geometric parameters on the failure characteristics of rock material. Improving the rock-cutting efficiency of continuous mining machines has proven to be an interesting research topic during the last few decades. In the current study, an automated rotary rock-cutting simulator, duplicating a continuous miner, was used to study these parameters in the laboratory. The improvement of bit performance in terms of its life, cutting efficiency, dust production and energy consumption has drawn widespread attention. Research has demonstrated that optimizing bit parameters can result in efficient fragmentation of rock. Indiana limestone rock material was used in this study. The bit tip angle, bit tip size, bit spacing, depth of cut and cutting velocity of the rotary drum were varied to investigate the failure characteristics. The cutting pressure, penetrating pressure and the depth of cut were monitored on the simulator during the cutting process. Airborne dust and settled dust were measured for each experiment. Then, the specific airborne dust and specific energy were determined for each type of bit. Triaxial tests were carried out to correlate the failure angle of the rock in the static case to the dynamic cutting process failure. The physical and mechanical properties of the rock were also determined to assess their influence on the wear characteristics of each bit.

Jan 1, 2000

Environmental conflict management approaches and procedures have been used to successfully address and resolve a variety of issues, problems, and conflicts related to the extraction of natural resources. Companies in the mining industry have been involved in a range of controversies over planning, siting, permitting, environmental, and enforcement issues. Through the use of conflict resolution case studies, this paper will present approaches and procedures that can help companies and other involved parties to successfully manage and resolve differences in a mutually acceptable manner.

Jan 1, 2000

By Osvaldo Bascur, Laurent Garrigues, Nouna Kettaneh, Svante Wold

The chemical, oil, semiconductor, mining, and paper and pulp industries, as well as most other modern industries, are rapidly expanding the range of measurements used to characterize raw materials, process steps, intermediates, and final products. In addition, process variables such as temperature, pressure, and flow become more and more numerous, providing extra information on the state of the process. However, no matter how many sensors are added, the underlying sources of variations that drive the process behavior remain constant. On the other hand, the measuring frequency of these data has increased from once a day or once an hour to once, ten, or even hundred times a minute. This gives masses of data that are swelling in both directions (more variables and more observations). These data need to be properly stored, managed, and analyzed to provide diagnostics about the state of the process as well as an understanding of the relationships between different parts of the process and the product properties. Projection methods such as PCA (principal components analysis) and PLS (projection to latent structures) compress process data to informative summaries of the original variables. These can be shown on line, providing an efficient, graphically oriented suite of diagnostics regarding the "health" and performance of the process. The power of these methods is illustrated by two examples of industrial data in the mining industry.

Jan 1, 2000

A novel pressure leaching process for platinum group metal (PGM) feedstocks is described. The process is particularly well suited for treatment of ores or concentrates that are too low grade for economic processing by the conventional smelting/leaching process. Operating conditions have been identified under which gold, the PGM's and the base metals dissolve simultaneously in a pressure leaching autoclave. The product of this leaching process can then be treated by one of several flowsheets, of which the preferred will likely involve solid/liquid separation, followed by precipitation (or adsorption on activated carbon) of gold and the PGM's, followed by copper solvent extraction/electrowinning. Depending on the concentrations of nickel and cobalt, the copper raffinate would either be partially recycled to the autoclave to allow NilCo concentrations to build up, or it would proceed directly to a Ni/Co refinery. This paper deals with the pressure leaching process and the recovery of gold and the PGM's from the pressure leach product.

Jan 1, 2000

By D. H. Diering

The paper takes the reader into the depths of a modern ultra-deep South African gold mine and gives a perspective on the vertical and horizontal extent of the tunnel networks in such a mine. Depending on the mine design layout employed, tunnels once excavated are subjected to various levels of stress change over their life time, and the support requirements are explained. It is suggested that shotcreting is the only viable ultra-deep level support medium, and after looking at the latest developments, the logistical problems are put forward. In an effort to overcome most of these problems, the South African ultra-deep mining industry embarked on a collaborative research programme in 1998. The importance of tunnelling and in particular tunnel support as a critical technology for future successful ultra-deep level mining is stressed. While not yet fully ?on top of? these problems and challenges, our industry is now fully addressing them and we expect to make significant progress during the next 4 to 5 years.

Jan 1, 2000

By P. N. Calder, D. B. Apel, S. D. Butt

Mine-wide (MW) microseismic systems use widely spaced transducers to determine the source location and parameters of stronger microseismic events, while high frequency (HF) systems use fewer transducers to monitor local areas for the weaker events that can precede stronger events. Previous monitoring at the Creighton Mine indicated that an HF transducer located 120 m away from an active stope recorded two types of activity in response to production blasting: the first occurring at the same time as the production blasts and associated with the passage of the direct seismic waves from the blast through the local area, and the second occurring several hours later and associated with the arrival of a slower moving stress change through the rock mass (which was identified by the mine’s MW system). Interpretations of locally increased stress levels, based on analysis of the recorded HF events, correlated with the nearby occurrence of two strong seismic events. These results were applied to a similar monitoring trail at the Kidd Creek Mine where the transient stress changes induced by several development blasts were monitored. It was observed that increases in HF activity corresponded with the occurrence of MW events near the transducer location, and that fewer HF events were recorded the longer this occurred after the blast. Local geological features appeared to influence the number and occurrence of both HF and MW events.

Jan 1, 2000

By G. A. Irons, G. S. Hanumanth

A three-dimensional mathematical model for the electric furnace of Cominco's Kivcet process was developed to compute the electric field intensity, power dissipation, temperature and velocity distributions in the furnace. A number of simulations of the electric furnace operation were carried out for various electrode immersion depths and electrode currents. The results showed that the current penetrated the bullion layer, generating high current densities in a layer approximately 0.3 m thick located in the slag/bullion interface region. An increase in the electrode immersion depth increased the furnace power as well as slag temperatures, and generated more vigorous bubble stirring and thermal homogeneity in the slag. For a given applied current, the computed power was in reasonable accord with the measured power input. The calculated temperatures were in rough agreement with the tapping temperatures of slag and bullion.

Jan 1, 2000

By N. Parra, M. N. Herrera, T. Vargas, B. Escobar, C. Gonzalez

originally published May 1998, Vol. 15, No. 2, pp. 15-1 9 Discussion by G. Rossi, University of Cagliari Reply by T. Vargas, University of Chili

Jan 1, 2000

This chapter explores leadership behavior in a life-threatening situation-fire in a coal mine. Previous chapters have discussed the database of interviews with miners who escaped from underground fires. Researchers raised questions such as: (1) Who led the miners out of the mine? (2) Did leadership make a difference in the escapes? (3) Was the escape leader the hierarchal leader? (4) What, if any, characteristics did the escape leaders possess? Subsequently, researchers analyzed the mine fire database from a group interaction perspective to address the leadership questions posed. Leadership has been one of the most researched topics of human behavior in the twentieth century. Studies have ranged from individual characteristics of leaders, to situational leadership, to interaction of leader and follower, suggesting different leadership techniques for different followers. The question that emerges here is: Are there different types of leadership that "fit" different kinds of situations? In a crisis situation like that examined in the present study, such information about leadership may significantly improve the chances of escape. To address these issues, the study team looked at the formal authority structure before each fire, considered leadership behavior or lack of leadership during the escapes, and examined those conditions associated with the emergence of leadership. According to Bardo [ 1978], "Emergent behaviors are those forms of action, and the norms, values and beliefs governing those actions, that rise out of the disaster situation." This chapter discusses previous studies in the area of crisis leadership and examines the emergent behaviors of leaders under duress during the mine fire escapes. Previous Studies The research on leadership during emergency situations has consisted mainly of simulation and field studies, with the principal concern being escape from building fires. During the 1980s, Hayashi [1988] created a computer simulation model to evaluate leader behavior in a fire. Although his purpose was to aid in planning for disaster prevention, his findings are relevant because they address the issue of situational leadership in crisis-where a leader changes his or her behavior to fit the situation. Essentially, his simulation model was designed to judge the actions and thinking of leaders. The simulation was tried by 101 subject/leaders 4 times each. The simulation consisted of amaze containing the leader, an informal leader, and 50 evacuees. Interestingly, the results indicated that the leader's actions were not dictated by circumstances. Any differences in behavior were attributed to the individual characteristics of each leader. The study also showed that the worse the situation became, the less individual

Jan 1, 2000