Search Documents

By David Siskind, Mark Stagg

Vibrations from Dade County (Miami area) quarry blasting and structure responses were measured at 11 locations between February and April, 2000, and 10 homes were inspected to analyze the characteristics of their cracking and other damages. These results were combined with information collected by the County and other studies done in south Florida for a blasting impact assessment specific to this area. In addition over 40 quarry blasts in the nine-week monitoring period, about 800 measurements were available from previous monitoring in Dade and neighboring Broward counties. An overall worst-case analyses based on the highest individual amplitudes suggested that vibrations in some areas could have been as high as 0.35 in/s. While amplitudes in the study period were below this value, they were found to be relatively high for the distances and charge sizes. Attenuation with distance is less in Dade County than found elsewhere with quarries having to use scaled distances several times higher than similar sites in the north. Consequently, the vibrations are perceptible at very large distances.

Jan 1, 2001

"The McArthur River uranium deposit is the single richest uranium ore body developed in the world to date. The ore body’s average grade is 15% U3O8. Proven reserves are in excess of 450 million pounds. The grinding circuit is located underground. The ground ore is pumped to a surface facility where the slurry is thickened and loaded into containers for shipping to the Key Lake mill 78 kilometers to the south.The paper will briefly describe the mining method employed. The underground ore handling and grinding circuit, and surface facilities including slurry load out, wastewater treatment and the freeze plant will be described in detail. The paper will emphasize radiation and safety procedures that are followed to minimize operator exposure to radiation risks.LOCATIONThe McArthur River mine is located 78 kilometres north of the Key Lake mill. It is located at latitude 57’ N in northern Saskatchewan, within the southern boundary of the Athabasca formation. The nearest town is Pinehouse, located 320 kilometres to the south. Access to the mine is by an all weather road and by a private airstrip.HISTORYThe McArthur River Operation is jointly owned by Cameco Corporation (69.805%) and Cogema Resources Inc. (30.195%). Exploration for uranium in the McArthur River area started in 1980 by the Saskatchewan Mining Development Corporation, a predecessor company of Cameco.In 1984, a 12-kilometre long basement conductor was identified at a depth exceeding 500 metres. Systematic exploration drilling of this conductor resulted in the discovery of the P2 North deposit. Subsequent surface drilling programs from 1989 to 1992 delineated a narrow ore zone over a strike length of 1700 meters at a depth of 500 to 600 metres. At this time, geological reserves for the deposit were estimated to be 2.4 million tonnes at a grade of 5.0% U3O8 for a uranium content of 260 million pounds U308"

Jan 1, 2001

By Philomene Verlaan

Analysis of the relationship between environmental parameters and the content of Mn, Ni, Co, Cu, Fe and Zn in ferromanganese crusts permits improved identification of locations to prospect for crusts with commercially valuable concentrations of these metals. In this study we asked whether a statistically significant relationship exists between primary productivity of the overlying surface waters, the concentration of O2 in and depth of the O2 minimum layer on the metal content of non-hydrothermal ferromanganese crusts in the Pacific Ocean between 130o W and 175o E and 0o to 30o S (the study area). To further develop the interpretation of the results of the statistical analysis and to assess in detail the geographical expression of these parameters in terms of metal content in crusts, a geostatistical technique (kriging) was used to generate contoured values for metal content, primary productivity and O2 concentration in and depth of the O2 minimum layer in the study area.

Jan 1, 2001

By E. J. Peuraniemi

Primary copper production using suspension smelting techniques like Outokumpu Flash Smelting always causes some dust formation. Flue dust particles are formed when sulphide feed material reacts violently with oxygen inducing particle disintegration and total desulphurisation of fragments. In the process, flue dust follows the off-gases to the heat recovery boiler (HRB) where its sulphation takes place because of prevailing conditions. Sulphation releases heat and causes also a drop in particle melting temperature and, further, particle sticking to the walls and heat exchange tube banks. Sulphation of synthetic CU20 particles were examined using a laboratory scale fluid-bed reactor. This study aims to a better understanding of flue dust behaviour in a HRB and, thus, to a better operational practise and design of a HRB. The effect of PSO/PO2 -ratio and temperature on the sulphation kinetics were tested. Standard chemical analysis, light optical and scanning electron microscopy with energy dispersive spectroscopy were used to examine the samples.

Jan 1, 2001

By K. Prajapati, P. Hes

Transmission of vibration to the operator from percussive vibrating tools is increasingly of concern in industrial and mining applications. Prolonged exposure to high levels of vibration transmitted via the hand causes disorders known as hand-arm vibration syndrome (HAVS). The vascular component of HAVS is called vibration white finger (VWF) and has a debilitating effect on the hand. Vibration at frequencies below 1250 Hz, a tight hand-grip force and cold environments are reported to increase the likelihood of developing VWF. A vibration damping handle design with patents pending that addresses some of the causes of VWF has been developed and retrofits onto jackleg pneumatic rock drills. The handle is decoupled from the drill while maintaining jackleg twist-grip controls on the hand-grip using a combination of sealed self adjusting hydraulic pistons and compliant materials in series, and a new air control valve. The ergonomics of the hand-grip was also modified by the addition of a polyurethane sleeve with a diameter of 50 mm. The new hand-grip reduces direct cold metal contact and minimizes grip force. Measurement of vibration as the quantity acceleration was made in accordance with international standard ISO 5349. Overall vibration damping in all axes of 50% to 63% was attained at frequencies below 1250 Hz. The dimensions of the damping handle are comparable and its weight is only 100 g heavier than a standard handle.

Jan 1, 2001

By A. Swanson

The Australian coal industry has been subdued in recent years and only a few new plants have been constructed, but the drive for greater efficiency has seen continued technological developments. The paper lists the new plants and major upgrades, plus summarizes technical developments in the areas of dense medium processing, fine coal treatment, froth flotation, dewatering and on-line analysers.

Jan 1, 2001

By Seung-Kyu Son

Environmental properties of the northeast Equatorial Pacific along 131.5 degrees west, between 5 degrees and 13 degrees north latitude, were investigated in association with changes in water column structures during the summer seasons of 1998 and 1999. Climatic disturbances such as El Nino and La Nina, should have affected this area during the study period. In 1998, a thermocline where temperatures rapidly decrease with depth, was formed at 90~110 m water depth. However, in 1999, a very fluctuating thermocline was observed with latitudes. As a result of changes in the water column structures, biological and chemical environment also showed fluctuation parallel to the changes in other physical parameters. Inorganic nutrient depleting areas, especially for nitrate+nitrite and phosphate, or oligotrophic regions were extended down to approximately 100 m depth, which coincided with the surface mixed layer depth. In the euphotic zone, depth integrated nitrogen (N) and phosphorus (P) values were 34 g-N/m2 (grams of Nitrogen per square meter of sea floor), 7 g-P/m2 in 1998 and 130 g-N/m2, 18 g-P/m2 in 1999, respectively. The results indicated that nitrogen (96 g-N/m2) and phosphorus (11 g-P/m2) are supported by up-welling and down-welling phenomena with convergence and divergence in the study area. Biological parameters in the water columns were largely determined by the physico-chemical environmental parameters. Subsurface chlorophyll maximum layers were coincided with the formation of seasonal thermocline. Copepods were the dominant group of zooplankton community at three sampling stations (N5, N6, N10) terms of abundance, which was the same results of previous surveys for the past 3 years. Among copepod populations, Oncaea sp., Oithona sp. Clausocalanus sp., Acarocalanus sp. and juvenile copepodites were dominant Appendicularians, foraminiferans and radiolarians were also dominant. To investigate diel vertical migration pattern of zooplankton, repeated samplings from the water depth of 0~50m and 50~200m were conducted at KODOS (Korea Deep Ocean Study) area before and after sunrise. Zooplankton abundance was slightly higher after sunrise than before sunrise in the surface layer. Chlorophyll-a concentrations were relatively low as the concentration of sediment increased in most experiments possibly due to a decrease of grazing pressure of microzooplantkon such as ciliates, which is the efficient grazer on small-sized phytoplankton. Because copepod predation on microzooplankton may be prevented by the high concentration of sediment, resulting in lower grazing pressure on small-sized phytoplankton. The results obtained during the baseline study as a part of KODOS project since 1998.

Jan 1, 2001

By V. K. Paruchuri, J. D. Miller, J. Nalaskowski

The phenomenon of surfactant adsorption at mineral surfaces is of significant importance in many particulate processes ranging from mineral flotation and enhanced oil recovery to pharmaceutics, paint technology and the casting of high quality ceramics. Stability of the dispersions is related not only to the amount of adsorbed surfactant but also to the structure of the adsorbed surfactant molecules at the interface. This structure greatly depends on the type of surfactant and the hydrophobicity or hydrophilicity of the surface. On hydrophobic surfaces surfactants adsorb regardless of surface charge by van der Waals/hydrophobic inter-actions with hydrocarbon chains accommodated at the surface. On the other hand, on hydrophilic surfaces the surfactants adsorb through electrostatic interactions with their polar moiety fixed at the surface. In the latter case, the electric charge of the surface and surfactant plays a crucial role in the surfactant adsorption process. The recently developed soft-contact Atomic Force Microscopy technique has revealed images of adsorbed surfactant structures at various interfaces. The adsorbed structures of a cationic surfactant (CTAB) and an anionic surfactant (SDS) are presented in this work for different concentrations at hydrophobic graphite and hydrophilic mica surfaces. Different types of micellar arrangements have been observed at these surfaces for surfactant concentrations around the critical micelle concentration. The structures are more ordered and well defined at the graphite surface than at the mica surface. These results have been correlated with the hydrophobicity of the surfaces as revealed by contact angle measurements.

Jan 1, 2001

By W. G. Davenport

Inco flash smelting blows industrial oxygen, dried Cu"Fe-S concentrate, Si02 flux and recycle materials horizontally into a hot (-1500 K) furnace. Once in the furnace, the oxygen reacts with the concentrate by Reactions 1.1, 1.2 and 1.3 to give: (a) liquid matte, 55 to 60 mass%Cu (b) liquid slag, 1 to 2 mass% Cu (c) off gas, 60 to 75 volume % S02. The matte is tapped into ladles and sent to converting, Fig. 1.3. The slag is tapped into ladles, and sent to a stockpile; with or without a Cu-from-slagremoval step. The off gas is water-quenched, cleaned of dust and sent to a sulfudc acid plant. The [nco flash furnace is also used to recover Cu from molten recycle converter slag. The slag is poured' into the furnace via a steel chute and water-cooled door, Fig. 3.1. In 2000 there are five Inco flash furnaces in operation: at Almalyk, Uzbekistan (Ushakov, et at. 1975); Hayden, Arizona (Marczeski and Aldrich 1986); Hudey. New Mexico (Belew and Partelpoeg, 1993); and Sudbury, Ontario (two furnaces, Carr etal, 1997, Humphris et ai, 1997; Molino et ai, 1997). The Almalyk, Hayden and Hurley furnaces smelt Cu-Fe-S concentrates. The Sudbury furnaces smelt Ni-Cu-Co~Fe-S concentrates'to produce -45% Ni+Cu+Co matte and -1% Ni+Cu+Co slag.

Jan 1, 2001

By Jay Smerekanicz, Florin: Pedersen Gheorghiu, Alan Cameron

In order to expand the capacity of Modern Landtill, a groundwater extraction system consisting of a linear system of pumping wells over 2,700 feet long had to be replaced. The new system would be covered by landtill cells to a depth of approximately 400 feet, and therefore would have to be maintenance free. In addition, the new system had to be proven to be more effective than the previous system, groundwater extraction had to be maintained during construction and construction could not disturb either the landfill operation or nearby residential neighbors.

Jan 1, 2001

By Bradshaw, Y. S. Cho

The size of bubbles plays an important role in flotation. Equations used to calculate the size of bubbles all show the effect of liquid/gas surface tension. However, the surface tension does not change much with frother concentration and experiments conducted using single capillaries (or single-hole spargers) do not reveal any clear effect of the frother concentration on bubble size. The size of bubbles does, however, strongly depend on frother concentration when multi-hole spargers are utilized (or when measured in a flotation cell); at low frother concentrations the bubble size is much larger indicating coalescence as a main mechanism determining the size. Coalescence can be prevented at frother concentrations exceeding the critical coalescence concentration (CCC), which in turn was found to be interrelated with the dynamic foamibility index (DFI).

Jan 1, 2001

By Zhijing Zhang

A thermodynamic structure model for alkali borate melts is developed to describe the distribution of structural groups in the alkali borate melts as a function of compositions. Fractions of threefold coordinated boron atoms and fourfold coordinated boron atoms in the potassium borate melt are calculated for the entire composition range and compared with results reported in the literature. The model has been used for structural interpretation for the borate anomaly in viscosity, which regards the borate anomaly as a manifestation of the various antithetical effects caused by the introduction of alkali oxide into boric oxide. It has been found that the viscosities of alkali borate melts increase or decrease according to the changes in rigidity and spatial connectivity of the glass network structure, which is a function of temperature and composition.

Jan 1, 2001

By J. B. Hadaway

The current limit to power transmission for grinding mills through one mill pinion is approximately 7,500kW. Above this power rating either twin pinion arrangements or Gearless drives are required. The SMTP concept was developed to overcome this limitation by using two pinions with a single large drive motor. The SMTP mill drive offers major advantages in capital cost and greatly simplifies plant layouts, while using an innovative adaptation of industry-proven single helical gearing. Through the use of a single motor, provision of variable speed drive is greatly simplified. The SMTP can also be used for significant power upgrades on existing mills.

Jan 1, 2001

By S. Moussa

The formation of boron-doped nickel aluminides Ni3AI, (76 at. % Ni) from elemental powders by reaction synthesis using reactive sintering was studied. The process involves the mixing of elemental powders of nickel and aluminium with various wt % of boron up to 1 wt % boron. Nickel and Aluminium powders were mixed in the correct proportion to form the intended boron-doped nickel aluminide intermetallic. XRD, SEMI EDS, Image analysis and Archimedes principle; were used to study the effect of Boron addition on the final microstructure, bulk density, average grain size of as reactively-sintered nickel aluminides (boron-doped), compared with no boron addition. The results showed that at greater boron content than 0.3 wt %, a two-phase non-equilibrium microstructure of consisting of NiAI phase in NiJAI matrix was formed that have been primarily retained even after heat treatment for 5 hours at 1000 °C. Boron was present in solid-solution within both the NiAI and the Ni3AI (in greater amounts) phases.

Jan 1, 2001

By Rundqvist

The best method to minimise disturbances from traffic to the neighbourhood and in Urban is probably to go underground. For obvious reasons this will cause vibrations, noise and other environmental effects which need very strict regulations and quality assurance in order to complete the work successfully. One project is “Southern Link”, a part of a ring road system. The system of tunnels includes 16 kilometres of tunnels right beneath the south part of the city of Stockholm. At least 20.000 people will be or could be affected by different kinds of disturbances and pollution such as vibrations, noise, gas and groundwater. Another project is the “Arlanda Link”. A new railway with three stations has been built under the existing and running to Arlanda airport with its terminals. Authorities have carefully judged these projects, which cause complaints from neighbours due to disturbances. The blasting operations are professionally managed by the contractors and controlled by consultants to keep the regulations according to the Swedish standards, which are well described in the tender documents by risk analysis and technical descriptions. In spite of that, one conclusion is that it is not always possible to go underground without exceeding stipulated regulations with existing technique. Some of the regulations also double the cost of excavation

Jan 1, 2001

By Robert E. Blackett

To help local governments plan for long-term supplies of sand and gravel for buildings and infrastructure, the Utah Geological Survey is assessing natural aggregate resources (mainly sand and gravel) in the St. George, Utah area. Whereas much of the aggregate in the study area is adequate for road-base construction, high-quality aggregate for Port- land cement concrete is limited due to geology, and also due to land administration and environmental issues. Virgin River alluvial gravels southwest of St. George are generally poor sources of aggregate because they contain clasts of soft sediments and soluble minerals derived from Mesozoic rocks. Elsewhere, widespread secondary calcium carbonate (caliche), as rinds and matrix in gravel, lower the quality of material. Young river-terrace deposits in Fort Pearce Wash, and along the Virgin River above St. George are the primary sources of sand and gravel for the area. Alluvial fans on the east side of the Beaver Dam Mountains, and on the west side of the Hurricane Cliffs are also sources of aggregate. Stream-channel deposits associated with "inverted valleys" north of the towns of St. George and Hurricane, Utah, and older pediment gravels on the west flank of the Beaver Dam Mountains may be future sources of high-quality aggregate. Accelerated urban development during the 1980s and early 1990s has caused St. George and other communities in Washington County to encroach upon sand and gravel pits originally located in rural, undeveloped areas. Urban residents often view nearby sand and gravel operations as undesirable neighbors and pressure elected officials to close the pits. Pit closures effectively eliminate the remaining reserve from the sand and gravel resource base of the area. More- over, resources may also be lost as new homes are built upon undeveloped sand and gravel deposits. The St. George area is particularly susceptible to loss of aggregate resources because high-quality natural aggregate for construction is already in short supply. Moreover, most of the land in the study area is administered by the U.S. Bureau of Land Management and subject to various land-use restrictions. Much of this public land cannot be developed for mineral materials, such as sand and gravel, because of federal regulations protecting rare plants and animals, archaeological sites, and important watershed areas. Of particular concern to resource development are areas designated as Areas of Critical Environmental Concern, Wilderness Areas, and Wilderness Study Areas. Protection for Endangered Species is a critical element in all planning efforts. Those species present in the St. George area or in areas near- by include: the desert tortoise, southwestern willow flycatcher, Virgin River chub, and dwarf bearclaw poppy. As the St. George area is depleted and/or deprived of sand and gravel resources through extraction and urbanization respectively, construction costs will rise unless conservation measures are instituted. To avoid the loss of aggregate resources, the UGS is pursuing a program of data gathering and field surveying of surficial deposits to determine tonnage and quality of the remaining sand and gravel resources. The resource information from this program will help land planners, developers, and government officials make informed decisions concerning urban development throughout the region.

Jan 1, 2001

By Y. Wang, E. Forssberg, A. Johansson, B. Chan

A super-conducting high gradient magnetic separator with matrix vibration in dry separation mode is a powder purification device, which has been used to remove weakly magnetic impure particles from fine calcite powders below 53 µm in this study. A fundamental question concerned is the evolution of the matrix clogging under gas-solids loads. This paper presents the improvement of the separation selectivity using a method of mechanically based vibration on the matrix in the separator. The functions of the matrix vibration are discussed. The results indicated that the mechanically based vibration on the matrix within a high intensity magnetic field while a feed was introduced in an air stream, was found to be effective for the dry purification of fine powder materials.

Jan 1, 2001

By N. Wang, A. I. A. Salama

"An index to evaluate the amenability for processing of different coals is implemented. The index is based on the well-known Mayer-curve or M-curve. The index is superior to other existing indices and is implemented using Microsoft-Excel™. Several coals are used to demonstrate the implementation of the index proposed.IntroductionIn 1950, Mayer introduced a curve that carries the information embedded in the fir s t three curves or ash curves of the conventional washability tables and curves (Peng et al., 1979; Osborne, 1988). The curve was labeled the Mcurve (abbreviation for Mittlewertkurve in German or the Mayer- curve). The main idea behind the curve is to use the ordinate for the cumulative mass and the abscissa for the ash (attribute) mass. Specific slopes on the resulting curve represent the cumulative float, cumulative sink, and elementary ash (attribute) contents (Mayer, 1950, 1953, 1957; Venkatesan, 1975; Osborne, 1988; Salama, 1989). Beyond the ash values, the curve carries graphical information that can be used in evaluating coal processing characteristics. Consequently, it becomes possible to present several raw coals on a single diagram, thus making it easier to compare their processing characteristics. This is particularly useful in comparing various size ranges of raw coal or the same size range from different seams. Therefore, the M-curve is adopted as a vehicle for developing the “processing (washing) characteristics index” implemented in this paper."

Jan 1, 2001

By Deming Wang, R. A. Overfelt

"The oscillating cup viscometer has become a dominant technique to measure the viscosities of high temperature molten metals. Unfortunately, the viscosity estimation model from the observed logarithmic decrement and period of the oscillation is very complicated. There are still large discrepancies of viscosity estimation values between using different measurement facilities and using different viscosity estimation models for a same molten metal. The purpose of the paper is to evaluate the accuracy of an oscillating cup viscometer in Auburn University. Two well known viscosity estimation models, Roscoe's and Torklep's equations, are compared and discussed. The theoretical literature for the fluid flow inside an oscillating cup is reviewed and a more accurate working equation for the Auburn oscillating cup viscometer is developed. Some design parameters of the oscillating cup viscometer, which directly affect the accuracy of viscosity estimation by using the working equation, are discussed. In addition, applications and experimental measuring data are presented in the paper for several different commercial alloys, such as aluminum alloys: A319, A356 and A201, nickel-base super alloys: In713 and In718, and casting irons, C40 Gray Iron and Ductile Iron.1 IntroductionThe oscillating cup viscometer is the most important and has been most frequently used in viscosity measurement for high temperature liquids [1-4]. The principal advantages of this technique over others are its mechanical simplicity and the ability to measure the time period and amplitude decay with great precision. In the viscometer, a high temperature liquid (such as a molten metal) is contained within a crucible suspended by a wire to form a torsional pendulum, which induces torsional oscillation motion. This motion is damped primarily by viscous dissipation within the viscous liquid inside the cup. The viscosity of the liquid can be calculated by an analytical or numerical solution ofthe equations of motion of the oscillating cup system."

Jan 1, 2001

By Julian Malnic

Various natural, commercial, engineering and operational factors govern the evolution of approaches taken in the exploration for Seafloor Massive Sulphides (SMS) and in delineating the resource. These stages are prerequisites to the proposed mining of SMS deposits. This paper presents and analyses these factors from the view of an SMS exploration company that is pioneering the exploration of this rich alternative source of zinc, copper and gold. Current exploration practices developed by Marine Scientific Research (MSR) workers for SMS deposits are expected to give way to industry-generated methods as the SMS exploration industry gathers momentum. The exploration process falls into three phases that are described below: Prospecting (locating targets), Indicating Resources, and Measuring Mineral Resources Considerable streamlining of the SMS exploration process will accelerate the rate of discovery. The economics of SMS mining are projected to be superior to comparable terrestrial mining operations in both operating cash cost and capital terms.

Jan 1, 2001