Search Documents

By S. M. Spottiswoode

The aim of the hybrid location method is to improve seismic event locations by reducing the effects of errors in the wave velocity of ray paths between each event and each recording site. We report on further enhancements made to the hybrid location algorithm, which is based on the double-difference method developed by Spottiswoode and Milev1and Waldhauser and Ellsworth2. The term ?double-difference? refers to the residuals between the observed and theoretical travel-time differences and are obtained using either picked arrival times or various measures of time differences obtained from waveform pairs. These residuals are minimized for pairs of earthquakes at each station while linking together all observed event-station pairs. An important enhancement is that the double-difference term uses the median arrival time residuals to reduce the effect of outliers on the system of equations. In addition, the hybrid locations are further constrained by considering events of known locations, in this case along lines of development blasts. We relocated some 20 000 previously located seismic events in the Driefontein 5E area; 5 800 of these events were considered to have been development blasts and we constrained their locations to lie on the straight lines joining about 2 150 survey pegs from the mine?s database. Relocated events were shown to distribute more closely around advancing faces than had been the case before relocation. Wave velocities from the development blasts show evidence of anisotropy.

Jan 1, 2005

In the leaching and recovery of gold from copper containing gold ores using cyanidation, some copper minerals also dissolve which can have a detrimental effect on the process efficiency and economics. There are also environmental concerns with current operations discharging cyanide and copper cyanide species into tailings dams, and strict regulations prohibit this for greenfield plants. Cyanide destruction however is not an economic option for new plants treating copper-gold ores. This paper evaluates a potential recovery process to overcome the copper cyanide problem. Despite gold dissolution occurring in copper cyanide solutions having no free cyanide, gold recovery from ores is lower compared to free cyanide. Thus, cyanide addition has to be optimised to maximise the gold recovery whilst endeavouring to eliminate free cyanide at the completion of leaching (CN:Cu less than 3:1). Subsequently, copper cyanide can be recovered using activated carbon. The loaded copper cyanide is easily recovered from the carbon with a cyanide soak and distilled water wash such that the eluted CN :Cu ratio is less than 4:1. The copper could be recovered efficiently by electrowinning, by decreasing the pH of the eluant to 5. The remaining cyanide solution, after electrowinning, is then neutralised to form NaCN and recycled.

Jan 1, 2005

By B. Samanta

This paper investigates the performance of the neural network technique in a placer deposit situated at the Nome district in Alaska. Initially a single neural network model was constructed to estimate the gold grade. However, at a later stage, an ensemble model consisting of multiple networks was also constructed via the Adaboost algorithm. The reason behind the use of the ensemble model of the Adaboost algorithm was to examine if the ensemble model provided superior performance to the single neural network. As indicated by other studies, Adaboost did not have a better performance than a single neural network in this specific application. This may be due to the high noise inherent in the gold data used in this project. Consequently R2 values of gold prediction are also poor for both the single and multiple networks.

Jan 1, 2005

By L Wsrell

During recent years the iron ore industry has experienced a continuous consolidation trend following increased merger and acquisition activities. Analysing and evaluating these mergers is important in order to establish potential effects. The purpose of this paper is to analyse the price effects caused by the merger between Rio Tinto and North Ltd in 2000. The merger was cleared by the European Commission, as well as the Australian Competition and Consumer Commission, shortly after its announcement. The analysis will be conducted using a simulation model based on a proportionality calibrated almost ideal demand system, which uses the premerger situation in order to estimate the post-merger outcome. The relevant market is defined using shipments data. This is followed by the simulation model applied to the defined relevant market. The results show that the concentration on the market, given by the HHI, increases approximately 15 per cent, and that the market share of the new companyÆs reaches almost 20 per cent. Compared to the CommissionÆs assessment the results indicate a more concentrated market and thus a higher concern for possible competitive effects. Furthermore, the results suggest that the predicted average market price increase from the merger is 1.6 per cent. However, the merged firm is able to increase their average price by 5.1 per cent.

Jan 1, 2005

By B. van der Moolen, P. J. M. Groot

The introduction of liberalisation in Dutch mineral provision has created a lot of uncertainty on how and where to supply for the need of construction raw materials. Some possible effects of this policy shift are: 1. the extraction of materials from small pits with truck transport, 2. an increasing dependence on foreign suppliers, 3. the usage of marine dredged materials, 4. more input of secondary substitutes. The outcome of this policy and the resulting marketbehaviour have consequences for transport and infrastructure and hence for sustainability issues. Mineral provision, on the other hand, is also influenced by the availability of infrastructure. Insufficient transport capacity could hamper the development of mineral projects that render benefits to society. (Even) in a liberalising market for mineral provision, the central and local governments have an important role to play with regard to infrastructure and the effects of transport. Various trends point towards an increasing internationalisation in mineral provision. What will increasing trade and increasing influence of the market mean for transport infrastructure? How should increasing transport be judged with respect to sustainability? In the sustainability discussion these questions will have to be answered on a national as well as on a European scale.

Jan 1, 2005

By Huayang Luo, Hui Li, Wei Zhou, Gang Chen, Scott Huang

The beach and offshore gold resources demonstrated at Nome, Alaska are some of the richest found in Alaska. They contain potentially significant resources that may be exploited in the future. Several companies have contributed to the exploration and reserve estimation in Nome offshore gold deposits. More than 3,000 holes were drilled and over 10,000 offshore samples were analyzed in the Nome offshore areas of approximately 40 km2. Those 3,000 plus drill hole logs were converted into digital formats comparable with ArcGIS software. Considerable amounts of mineral resources data were processed and visualized using ArcGIS 8.3 and its geostatistic, 3D analysis, and spatial analysis components. In this study, based on the data processing and visualization results of ArcGIS, a user-friendly website for mineral resource management and utilization is developed using ArcIMS 4.0.1. ArcIMS is a GIS solution to build and deliver maps, data, and tools over the Internet. The Nome offshore mineral resources website presents the geostatistic and GIS analysis information. This site allows clients to access the information and perform ArcGIS analysis, such as interactive data query, and map layers display of the gold resource distribution, average grade, gold reserve, and relative mineral resource estimation via remote computers. With linkage to other related mining web sites, this web site allows users to search for related publications and more flexibly manage the information. A few other appropriate customized tools are also being developed to assist interactions between the server and clients for data analysis and management.

Jan 1, 2005

By SH. Shahsavari, H. Akbari, M. Noaparast, M. Oliazadeh

Mejel valley zircon ore in Iran is located in north part of Iran and was sampled to evaluate its concentration. The aim of this project was to define the mineralogy of this zone and separating zircon from other minerals using gravity concentrators and magnetic separators. It is constituted of various valuable minerals, mainly zirconium, niobium-tantalum, titanium, rare earth elements particularly cerium-bearing minerals namely zircon, sphene and rare earth elements oxides. We used statistical method for designing of experiments. Yates method used for analysis of basic experiments results. The grade of zircon in primary sample was 1.1%. Different experiments were designed to optimize all required parameters. The final concentration with 75% zircon was produced and final recovery was 79%. Finally, lab-scale based flow sheet was prepared using experiments results.

Jan 1, 2005

By Martin Banda, Gift C. Chisakuta, Moses Chabinga

KCM made a major modification to the Nchanga Tailings Leach Plant (TLP) changing the circuit from feeding post leach thickeners in parallel with leach discharge for solid ?liquid separation to a Counter Current Decantation (CCD) configuration utilising most of the existing equipment. The new circuit is aimed at improving copper recovery from approximately 70% to 79% through enhanced wash efficiency. The re-introduction of CCD circuit at elevated throughput of 46 000-tpd design was made possible due to the EIMCO E-Duc technology design which is an auto-dilution system that enhances solids settling rate. Commissioning (manual operation) which accommodated on-going operational requirements was phased and completed in January 2004. The circuit stabilised in subsequent months and in March alone an all time record copper recovery of 81.8% was achieved which contributed an extra 779 tonnes copper above the plant?s projected production plans. 100% of the project cost was paid back by end of April 2004 This paper discusses the work involved and the challenges faced during the re-commission

Jan 1, 2005

By Maurice C. Fuerstenau

INTRODUCTION The term, chelate, from the Greek for 'claw,' has its origin in the pincer-like representation of more than one atom of a single ligand bonded to the same metal atom, forming a ring-like structure. Depending on how many attachments exist on the sphere of coordination around the metal ion, ligands are referred to as bidentate, tridentate, tetradentate, pentadentate and hexadentate According to Calvin and Martell (1952) and Somasundaran and Nagaraj (1984), chelating agents must contain suitable functional groups, and their location within the ligand molecule must enable ring formation that is sterically possible. Typical structures that meet these requirements have been given by Fuerstenau and Herrera-Urbina (1988) and are listed in Figure 1. As noted, the functional groups of these reagents contain electron donor atoms such as oxygen, nitrogen and sulfur. Basic groups, such as amino (-NH,), are those that contain an atom with a lone pair of electrons. Acid groups are those, such as carboxylic (-COOH) which lose a hydrogen ion and coordinate with the metal atom. Examples of each of these types chelating reagents are given in Tables 1-4. The specificity of chelating agents for various metal ions has long been known and was utilized early in the search for new flotation collectors. In 1927, Vivian used ammonium nitrosophenylhydroxylamine as a collector for cassiterite. Holman (1929) tested dimethylglyoxime as a collector for nickel oxide. He also suggested taurin as a collector for oxidized lead ores. DeWitt and von Batchelder (1939) suggested the use of oximes as flotation collectors. Gutzeit (1946) conducted an extensive investigation on the use of chelating agents as collectors and as depressants for gangue minerals. The depressants are those reagents that form soluble chelates with metal ions that could function as

Jan 1, 2005

By Richard Brink, Eric M. Klein, Kenneth B. Andromalos

"A portion of the roof for a 129 x 144-inch, nearly 100-year-old sewer outfall in the City of Baltimore had deteriorated to the point that it resulted in the development of a large sinkhole in a residential neighborhood. A subsequent video inspection of the sewer outfall indicated that there was a hole in the sewer outfall, and it would need to be repaired . After initial backfilling of the sinkhole and repairs to the water service lines, a conventional wood shoring system was used to support the excavation and expose the Main Outfall Sewer to inspect and repair it. This excavation was unsuccessful because of loose sandy soils and high groundwater conditions. An innovative use of a steel reinforced jet grout excavation support system was ultimately used to underpin an adjacent 20-inch water main and other nearby utilities, and provide access to the top of the Main Outfall Sewer some 22 feet below the street surface to facilitate inspection and repair of the sewer. This excavation support system was also successfully utilized in the final repair of the sewer roof by serving as a buttress for the new roof system.1.0 IntroductionThe project site is located in a residential neighborhood with brick masonry row houses situated on the south side of Chase Street and a brick masonry church on the north side of the street. Figure 1 illustrates the location of the site. The City right of way is 65 feet wide, and the street is 40 feet curb to curb. The centerline of the Main Outfall Sewer runs parallel to and a few feet south from the centerline of the street. Other utilities running parallel to the street include a cast iron 20-inch water line built about 1910, a 24-inch terra cotta storm drain, a 6-inch terra cotta sanitary sewer, a 4-inch cast iron gas line and a 40-inch electrical duct. Cross utilities included a 4-inch gas line and several smaller water and gas service lines to the church and row houses. One gas line that was not shown in the City's GIS database was exposed during the excavation."

Jan 1, 2005

By A Maurer, N Pereira

Low-density explosives have been developed with trials being conducted for over 20 years and yet have still only gained limited market acceptance despite producing some very promising results. The biggest concern with industry acceptance has been disbelief that a product with lower density than the ANFO benchmark could fragment anything but the weakest of strata. Trials have been carried out with products such as diluted ANFO, low-density ammonium nitrate (AN) and various other mixes, although it has been only recently that low-density explosives have been accepted as a serious alternative to traditional products such as ANFO and heavy ANFO. The recent uptake of low-density products has been the result of several key factors: the current resources boom forcing AN supply issues, the development of new handling techniques, and a far better understanding of the utilisation of such products. This paper highlights the benefits of low-density products available in the market and focuses on the situations where low-density explosives can provide the end user with benefits that would otherwise be achieved through more time consuming methods. Through correct implementation, low-density explosives can provide the blast designer with another option when looking at the optimum method of breaking the rock. This while still controlling the other limiting factors such as cost, environmental impacts (noise, vibration, dust and fumes), coal damage and safety (stable walls).

Jan 1, 2005

By Bruno Bussière, Guosheng Zhan, Michel Aubertin, Vincent Martin, Robert P. Chapuis

The study evaluates the hydrological behaviour of exposed and covered waste rock dumps. The objectives were to determine the major factors influencing unsaturated flow in waste rock dumps and covers, and to improve the in-situ, laboratory and numerical modeling characterization methods. Using material properties obtained from in-situ and laboratory tests, waste rock dumps of different configurations, with and without covers, were modeled. It was found that a properly designed “Store, divert and release” (SDR) cover allows most of the water to be diverted downslope and discharged outside of the waste rock dumps. The SDR cover seems to work efficiently even in extreme storm events. The numerical modeling results show that the unsaturated hydraulic properties (e.g. air entry value and water entry value) of the materials largely control the infiltration of water into waste rock dumps.

Jan 1, 2005

A novel approach to validate size distributions obtained from bubble sizing techniques is introduced. The experimental rationale consists in verifying whether the output features the anticipated bi-modality when two uni-modal populations (ca. 0.5 and 5 mm) are mixed in a bubble column. The degree of deviation is quantified by comparing the calculated and real proportions on a volumetric basis. A sampling-followed-by-imaging technique was used to proof the concept. The results showed the anticipated bi-modality in which the real and calculated proportions corresponded with a deviation of less than 15 per cent, considered good given the severity of the test. However, the deviation was correlated to the superficial gas velocity (Jg) in the column and was consistently against smaller bubbles. Possible sources of bias are suggested.

Jan 1, 2005

By M. D. Seke

The flotation response of a Pb-Zn sulphide ore from the Rosh Pinah Mine (Namibia) was studied in the presence of inorganic depressants such as sodium cyanide and zinc sulphate. Poor flotation selectivity was observed in the rougher concentrate of the galena circuit despite the use of a large amount of sodium cyanide. Batch flotation tests have shown that the use of cyanide alone is not efficient for the depression of sphalerite from the Rosh Pinah ore when milling is carried out according to the current plant particle size distribution. The use of both cyanide and zinc sulphate improved the selectivity between galena and sphalerite much better than cyanide alone. Flotation selectivity is limited by the mineralogical texture of the Rosh Pinah ore sample. Microscopic analysis has shown that the presence of sphalerite in the galena concentrate is also due to poor liberation between galena and sphalerite, especially in the middlings. Hence, selectivity could be improved by regrinding the rougher concentrate prior to the cleaning stage. Keywords: sulphide ores, flotation, flotation depressant, mineralogy.

Jan 1, 2005

By A. Ashrafi

The electrochemical deposition of polypyrrole coating on different pretreated aluminum-alloy 7075 substrates was carried out using cyclic voltammetry, The pretreatment of specimens consisted of mechanical polishing and/or electrochemical etching, In the latter case, an aqueous solution of phosphoric acid and ethanol was used, The electrodeposition solution was 0,25 M pyrrole and 0,1 M oxalic acid in double-distilled water, The cyclic voltammetry scan rate used was 700mv/s, Morphology of the coatings was examined using scanning electron microscope (SEM), Using the Tafel experiment, corrosion resistance of the coated substrates was investigated in 0.1 M NaC1 solutions, Results obtained revealed that electropolymerization of polypyrrole on 7075 aluminum alloy would increase the resistance against corrosion in 0,1M NaC1 solution, Also it was observed that, compared with mechanical polishing, electroetching pretreatment would be more effective.

Jan 1, 2005

Future depth and production limitations of an ore hoisting system are fixed by its initial design criteria. There is little scope to extend these limitations once installation is completed. Depth and production rate upgrades from the initial duty to the hoistÆs practical limitations require capital expenditure in stages, each of which can be defined when assessing the initial system design criteria. A means of presenting and assessing the design criteria, the limiting factors in each option and the relative present and future capital costs is necessary to arrive at a solution that delivers the best value to the mine. Application of this technique to recent friction winder installations and upgrades in the Australian mining industry is of particular interest; however, the analysis methods are also applicable to drum hoists. It is usual to specify a minimum hoisting capacity and depth, based on mine ore handling design and production needs. The final hoist depth and production rate are usually a result of the initial hoist design and hence it is useful from the outset to specify a required production versus depth envelope for the mine. Technical solutions can then be modelled within this envelope at their initial and final duties and a comparative analysis made against the cost of installing and progressively upgrading each solution. Understanding the factors that constrain each solution to a maximum production rate at a given depth is important, as the costs of overcoming limiting parameters such as rope tread pressure and motor power can be significant. The task of understanding and evaluating the options open to the hoisting system designer is simplified using this approach. Communicating the results of a multi-dimensional problem such as hoist specification is also made easier using the graphical methods inherent in the analysis.

Jan 1, 2005

By Naj Aziz

n Australia, the common method of laboratory testing of bolt for load transfer capacity determination is by short encapsulation push testing. Some concerns are raised about the validity of the test methodology, as the method does not reflect on the actual load transfer characteristics of bolt in real field situation. Thus, laboratory testes were carried out to examine the load transfer mechanisms of bolts in both the push and pull conditions. Tests were conducted by shearing a short resin encapsulated bolt out of a cylindrical steel sleeve. Three types of bolts with different surface profile configurations were tested. The study was complemented with numerical simulation of the test methods. Irrespective of bolt type the average shear load and shear stress values were found to be greater in push test, and the displacement at peak shear load was greater in pull test. The average shear stifhess values were greater in push test. The numerical simulation of the bolts provided a clear understanding of the stresses and strains generated by different bolt profiles during both the pull and pull testing process, thus allowing a better appreciation of the load transfer mechanism process.

Jan 1, 2005

By Yundong Ma

In this paper the dynamic process of rock deformation and failure in the roadways of the #9 coal seam, Wuhushan Coal Mine by was simulated using the software "Rock Failure Process Analysis System (REPA)" [I]. Based on the simulation results, this paper analyzes the failure process, characteristics and weighting of the overburden as the longwall retreat mining proceeds. The roadway's behavior including deformation characteristics, failure mechanisms, stress distribution in the surrounding rocks and the effects of various support systems on roadway stability were analyzed and studied. While simulating the rock failure process with REPA, the model stresses can be obtained through two approaches: (1) the stress is reflected by the grayscale of pictures in the model failure process and (2) the model stress can be obtained by muti-element information, which is one of the commands in RFPA system. Data files of stress can automatically be created, and curves of stress and displacement of each element can be displayed in each step of computation. Keywords: Rock Failure Process Analysis System (RFPA); roof control; roof to floor convergence; combined support

Jan 1, 2005

By A B. Christie, F P. Bierlein

Lode gold deposits of the Western and Eastern provinces, South Island, New Zealand , formed as a part of the Cordilleran-style tectonism during Tasman/Tahua and Rangitata orogenesis along the Paleozoic-middle Mesozoic southern Gondwanan margin. These deposits, hosted by lower grade greenschist facies sedimentary rock sequences of the Buller, Takaka, Torlesse, and Caples terranes, universally show geological features that are consistent with the orogenic gold deposit model, and genetic features are generally suggestive of a metamorphic origin, with the possible exception of a magmatic fluid source for the mineralisation at Sams Creek. However, ore fluid chemistry in Mesozoic deposits of the Eastern province, particularly the low concentration of non-aqueous volatiles and the very dilute nature of the fluids, is uncharacteristic of most orogenic gold deposits; this must be explained by either a unique fluid source or fluid type, which we believe unlikely, or an unrecognised significance of relatively rare gas-rich fluid inclusions in the deposits. Absolute age data for gold deposits in both provinces remain equivocal, thus hindering definition of the exact temporal relationship between ore formation and terrane accretion, regional metamorphism, and magmatic arc emplacement. Mercury and antimony occurrences in subgreenschist grade parts of the Haast Schist may target the upper levels of unrecognised orogenic gold deposits. If low-grade, high-tonnage intrusion-related gold systems occur on the South Island, then they are most likely to be discovered in association with the small molybdenite-, scheelite-, or cassiterite-bearing quartz stockworks spatially related to the Karamea and Median batholiths.

Jan 1, 2005

By B. Salopek, D. Rajkovic, D. Rumenjak

In decision making support system, that are used in various fields of environmental protection (environmental impact assessment, environmental management systems, setting environmental standards and regulation, etc.), it is often important to apply various mathematical environmental engineering models. The question of linking environmetal engineering modeling to decision making support system used in environmental protection is not yet methodically solved. The reasons for that could be manifold. Decison making support systems, used in environmental protection, because they are simply taken from bussines decision making, are not often adequate for specific problems raised in environmental protection. On the other hand, there are great number of types of models in environmental engineering, what urges the problem of finding the way of their proper linking with decision making support systems. The application of fuzzy logic in that field is estimated as one of possible solution of the problem.

Jan 1, 2005