Search Documents

By P J. Harris, C T. OÆConnor

Collectors are used to impart hydrophobicity on particles thus increasing their chances of reporting to the froth phase. Also, the extent to which naturally hydrophobic gangue particles, such as talcaceous minerals, report to the froth can be reduced by the use of depressants. Thus the use of collectors and depressants will directly influence the extent to which hydrophobic particles report to the froth. However these hydrophobic particles will also have a direct effect on the characteristics of the froth phase, more strongly hydrophobic particles causing a reduction in the stability of the froth with the expected concomitant effects on grade and recovery. This study included microflotation (ie frothless flotation) and batch flotation of various ores using a number of different collectors and depressants and a newly developed froth imaging device (SmartfrothTM). Flotation performance was characterised by mass and water recovery, and recoveries and grades of the valuables. This paper shows how the various reagents influenced the behaviour of the pulp and froth phases. The critical importance of managing the type and dosage of reagents used in flotation with a view to optimising their influence on the froth phase is discussed.

Jan 1, 2005

By A. Wilkinson

An investigation into the performance of support systems that are currently used in South African coal mines was conducted. Five most critical components of a support system have been identified. These components are resin, bolt, hole, machinery/equipment and the rock type. All five of these components are equally important as failure in any of these components will result in an inadequate support system. The performance of resin used in South Africa was investigated through in situ short encapsulated pull tests. The results indicated that in the majority of pull tests, failure took place at the rock-resin interface, indicating that the rock failed before the resin shear strength had been reached. It is therefore concluded that the strength of resin currently used in South Africa is adequate. It is found that although the maximum bond strengths achieved form both resin suppliers were similar, there was a considerable difference in the stiffhess of the resins. Roof bolt diameters and rib heights of bolts from three major manufacturers were evaluated (approximately 80 roof bolts from each manufacturer). The results showed there is a significant variation in bolt diameters and rib heights in the same batch in roof bolts supplied by certain manufacturers. The results also showed that on average there are insignificant differences between the parameters that determine the bolt profile (rib angle, spacing between the ribs and rib thickness). The influence of these parameters on bolt performance was very small and could not be established in situ. Roof bolts from four major suppliers were also evaluated through in situ short encapsulated pull tests. The results showed that the reinforcing system using roof bolts from all four manufacturers performed almost identically in sandstone, but somewhat differently in other rock types. The effect of bit types was evaluated. Both the stresses and the maximum loads obtained from the two-prong bits were greater than those obtained from a spade bit. Borehole annulus was found to be another important parameter that determined the support performance, and was investigated. The results from these tests showed that an annulus between 2.8 mm 4.5 mm resulted in the highest bond strengths. The results also showed that as the annulus drops below 2 mm, it appears to have a negative effect on the bond strength. The effect of wet and dry drilling on support performance was investigated. The results showed that wet drilling can-provide relatively greater system stiffnesses and slightly greater bond strengths. Short encapsulated pull test results showed very distinct differences between bolt system performance in different rock types and that sandstone produces significantly better results than shale and coal. From the results it is concluded that rock type is probably the primary factor influencing support system performance. A detailed investigation into the specifications of roofbolters that are currently being used indicated that the quality of installation of a support system is directly related to the performance of the equipment that is used to install the bolts. The important parameters, torque, thrust and speed of bolting equipment were investigated. The results showed that there are significant variations in these parameters in South African roofbolters.

Jan 1, 2005

By P. C. Patnaik

Performance of industrial gas turbine engines in terms of power output, reduced cooling and efficiency have been continuously increasing in parallel with aero gas turbines due to the advances made in the development of new materials, protective thermal barrier coatings (TBCs) and the advanced diagnostics to monitor service induced problems such as hot corrosion, thermal and thermo-mechanical fatigue and other operational issues, Environmental attack (hot corrosion or high temperature oxidation) is a common degradation mode in the hot section of the gas turbine, Hot corrosion occurs when Na or K bearing compounds in the environment or in the fuel combine with other contaminants such as S and Pb or V to form corrosive sulphates or vanadates thus attacking the protective oxide on the turbine airfoil, These problems pose far more threat to new turbine engine materials such as directional solidified, single crystals and ceramic matrix composites (CMCs). The CMCs due to their increased temperature capability, when used in the combustion chamber, are likely to reduce the peak temperatures attained during combustion and therefore provide the benefits of reduced emissions of oxides of C and N, These issues will be reviewed critically and their impact will be assessed on gas turbine lives. With respect to alternate fuels, past experience has shown that utilization of residual oils and coal derived fuels in gas turbines have resulted in complex deposition and corrosion processes, In recent years biomass derived alternate fuels have been used either through a gasification cycle or through direct firing of the biomass derived liquid fuel with a view to reduce Green House Gases (GHGs) and improve the climatic conditions. In both cases, the resulting high temperature corrosion processes (in the presence of alkaloids in the fuel) are also very complex, leading to premature removal of hot section components, Technology solutions mitigating these fundamental problems will be reviewed and solutions presented.

Jan 1, 2005

By I. M. Morsi, S. Z. El-Tawil, O. A. Fouad, K. A. El-Barawy, M. B. Morsi, M. M. Nasr

Upgrading of a low-grade titanium slag (~55% TiO2) with high silica, calcia, magnesia and iron contents has been studied using sulphation roasting technique using SO2/air gas mixture followed by hydrochloric acid leaching. XRD analysis of the sulphated slag reveals the presence of kennedyite (Fe2O3. MgO. 3TiO2), rutile (TiO2), calcium sulphate (CaSO4) and calcium silicate (3CaO.SiO2) phases. The residue after leaching contains mainly kennedyite, rutile phases and free silica with traces of calcium silicate phase. Synthetic rutile that has about 83% TiO2 can be produced at the optimum conditions. Thermodynamic calculations give rational explanations of the obtained results.

Jan 1, 2005

By Elif Çevik

This study deals with the mineralogical-geochemical characteristics and the industrial usage of the olivine from the dunites that crop out on the west of the Topuk village (Orhaneli). Mineralogical compositions of non-altered dunite samples are averagely as: Olivine (>90%), serpentine (1-4 %), opaque minerals especially chromite, magnetite, pyrite (1-3 %), and secondary minerals as magnesite, chlorite (1-2 %). X-Ray Diffractograms of the dunite samples indicate that olivines are in forsterite (93 on an average) composition, and chlinochrysotile and lizardite accompany to the forsterite. Chemical analyses of the dunites show that MgO, SiO2, Fe-,03 and LOI contents vary from 40,99 to 50,2 %, 34,67 to 40,6 %, 6,8 tol3,7 %, 0,11 to 11,27 %, respectively. SE-TAT Mining Company states that the study area has 400.000.000 tonnes proved, 800.000.000 tonnes probable and totally 1.200.000.000 tonnes olivine reserve. Consequently, all studies indicate that Orhaneli Olivin has convenient mineralogical and chemical properties and the grain size (0.04-40 mm) for industrial usages such as abrasive, olivine sand products, steel slag conditioner, balast and covering material in industry: Orhaneli olivines are demanded especially from the firms related to refractory industry, iron-steel factories, naval forces and shipyards. SE-TAT Mining Company also exports these olivines to different countries such as Macedonian and Spain.

Jan 1, 2005

By Alan Bye

Sandsloot open pit is situated on the northern limb of the Bushveld Complex, 250 km north east of Johannesburg, South Africa. Sandsloot is currently the largest open pit platinum mine in the world and is one of six potential open pits in the area. The geotechnical strength properties of the Platreef have posed significant mining and processing challenges to the PPRust operation since inception in 1992. In order to optimise the whole business as opposed to isolated cost centres a mine to mill initiative was embarked upon in 1997. Initial work focussed on ore characterisation and an entire suite of data was collected for each rock type. This included mineralogy, geochemistry, geotechnical, blastability indices as well as metallurgical strength data. The second phase involved the clear definition of customer requirements, namely the optimum performance criteria for the plant and mining departments. This involved extensive field trials and data capture to measure the interaction and influence of the mine to mill value chain. Once the design targets were defined a 3D geotechnical model was constructed to ensure that the targets were consistently achieved. The model is very similar to an ore reserve model however it is populated with geotechnical, metallurgical and blast index data. Through software queries the appropriate blast powder factor for each mining block can be obtained thereby ensuring the correct fragmentation is blasted for the plant and mining operation. The initiative has delivered significant results showing improvements across the mine to mill value chain. These include increased loading rates, reduced electricity and crushing consumables as well as higher plant throughput. Additionally, the initiative has benefited both Brownfield and Greenfield projects on the PPRust operation.

Jan 1, 2005

By R W. Wilson, A R. Branch

For hot mines, the use of mechanical refrigeration machines has become an essential feature of ventilation and cooling systems. Over the last 30 years, considerable effort has been made in developing refrigeration strategies and equipment to provide cooling that is cost-effective, reliable and energy efficient. In addition to these general design requirements it is necessary to take into account project specific factors such as long term mine cooling needs, operating strategy and installation time. This paper examines a number of actual mine cooling installations which illustrate how these features have influenced the design and installations. For many mines, it is known how the cooling requirements will increase as the mine develops, based on the life of mine plan. The design of the cooling installation must cater for both short- and long-term needs. The initial installation (to meet short-term requirements) must form an integral part of the ultimate cooling installation and as additional equipment and refrigeration machines are installed, it is necessary to ensure that the system remains cost-effective, reliable and energy efficient at all stages. For many mines, refrigeration machines are installed on surface and either operated near-continuously, or for the summer months only. Different maintenance strategies and policies with regard to standby equipment are highlighted for three mine installations. In spite of developments in cooling strategy, the cost of providing refrigeration remains expensive and many mines delay the introduction of refrigeration, as long as possible. When it is finally accepted that refrigeration is absolutely necessary, it is frequently necessary to æfast trackÆ the installation. To minimise site erection time and meet installation deadlines, factory pre-assembly and standardised modular equipment are widely used.

Jan 1, 2005

By A. J. Benham, H. Kessler

In the UK a high proportion of land-won sand and gravel is extracted from sub-alluvial gravels and river terrace gravels located within river valleys. However, extraction from deposits of this type is increasingly proving to be less acceptable. Quarries within river valleys often have a high visual impact and the cumulative impact of these operations in close proximity to each other can be high (figure 1). River valley operations are almost always restored to open water. Whilst these may be attractive for nature conservation and provide leisure activities, they can also have a serious impact on the natural hydrology of the flood plain. Wet restoration of quarries located close to airports or airfields can also lead to concerns regarding increased risk of bird strike on aircraft. The Civil Aviation Authority recently suggested that an exclusion zone of 13 km be applied around all airports and airfields to reduce the potential for bird strikes on aircraft. This action is likely to have a serious impact on the availability of potential sand and gravel extraction sites in river valleys.

Jan 1, 2005

By C. Hu

A MOS capacitor hydrogen sensor array is reported for hydrogen gas distribution mapping. Si(100) was used as substrate for film deposition. After silicon oxide growing on the silicon surface with dry thermal oxidation, palladium film was sputtered on silicon oxide as hydrogen-sensitive gate material in MOS structure. The 3x3 sensor array was patterned on silicon substrate and packaged in one chip. Sensors' response was test with impedance analyzer. The sensors in array were calibrated in the hydrogen concentration range from 10ppm to 10000ppm. The 2D hydrogen concentration distribution was obtained with the calibrated sensor array.

Jan 1, 2005

By J Manuel, R Muddle

The demand for iron ore has increased significantly in recent years, with new iron ore sources being mined to meet this demand. As the composition of sinter blends changes with the availability and cost of iron ore, so too does interest in the impact of new ore types on granulation and ultimately productivity. This paper describes a study into granulating characteristics of seven iron ore types, including various hematite and goethite ores. The effect of ore type on feed moisture requirements, green bed permeability, green bed strength and granule size distribution was examined for single ore blends containing coke, flux and returns. The ore size distribution was varied in these blends and its effect on granulating characteristics examined. It was found that the optimum moisture requirement of the ore was more dependent on ore type than ore size distribution, but ore size distribution (and specifically intermediate particle loading) had a greater effect on green bed permeability. The saturation moisture value for an ore was found useful in predicting both optimum granulation moisture and green bed permeability.

Jan 1, 2005

By B J. Fallon

This study used structural equation modelling (SEM) to develop a series of models to explain the impact of work-life balance on employeesÆ perceptions of job performance, job satisfaction, turnover intentions and absenteeism. The sample comprised 257 participants (108 males and 149 females) from a range of occupations and levels of seniority. In sum, the results clearly demonstrated that successful work-life balance is associated with higher levels of job performance and worker satisfaction and with decreased levels of absenteeism and turnover intentions. The data also lent support to the impact of employeesÆ coping styles, schedule flexibility and supervisor support on employeesÆ abilities to balance work and life. It is concluded that tangible benefits to an employerÆs bottom-line can be anticipated from organisational initiatives to assist employees to better balance their work and personal lives.

Jan 1, 2005

By Jewel A. Gomes

Keywords: Electrocoagulation, arsenic removal, fuel cell, windmill, energy simulation, combined Fe-Al electrode assembly Arsenic contamination of well-water in different countries has caused signs and symptoms of arsenic poisoning. Although several physicochemical treatments are presently used for the removal of arsenic compounds from drinking water, an electrochemical treatment, electrocoagulation, is a promising processing technology and currently is the most efficient (above 99% removal) and environmentally friendly technique, particularly if combined with alternative energy sources. Wind and fuel cell technologies can be considered the most promising developmental clean power sources. We will discuss new insights into the materials processing mechanisms and show the coupling of electrocoagulation with fuel cells and simulated wind energy sources. Different electrocoagulation plate materials were considered, along varied currents from the fuel cell to produce maximum arsenic removal. Coupling these technologies will remove carcinogenic arsenic from water sources, and will exhibit efficient usage of these energy sources by producing pure water for human and agricultural consumption.

Jan 1, 2005

By J. M. Ortiz, J. P. Bertini

"In mineral resource and ore reserve estimation, several sources of information are generally available, such as diamond drillholes, reversed-circulation drillholes, and blastholes, and originate from one or more sampling campaigns and are analyzed by one or more laboratories. In such a situation, the grade measurements may not have the same precision and one should distinguish between hard and imprecise data.This work aims at studying the impact of data imprecision in resource/reserve evaluation through two case studies on simulated deposits: a porphyry copper deposit conditioned to real exploration and production data, and a gold deposit simulated without any conditioning data. Several geostatistical techniques are used to estimate the grades of selective mining units from exploration samples, including kriging, cokriging, lognormal and indicator kriging. Two types of imprecision are examined— measurements with multiplicative errors and measurements defined as intervals. The results are compared to the simulated grades of the selective mining units from a statistical and economic viewpoint.The study concludes that imprecise measurements should never be discarded because they help to improve the estimates, and that simple methods such as kriging are as efficient as more sophisticated ones for resource/reserve assessment. Finally, a few indications on how to diagnose and model the data imprecision are given."

Jan 1, 2005

By M Darby, B Burdett, F Lovell

The results of the process control improvement project aimed at improving the quality of Australian Bulk MineralsÆ (ABM) iron ore pellets produced by four vertical shaft furnaces are very positive. These results are achieved through process stabilisation and optimisation, improvement in process monitoring and taking early corrective actions when operating variables were outside the target ranges. A number of benefits are obtained from this project. These benefits include: More consistent and improved pellet quality. The average cold compression strength (CCS) value of pellets produced during the eight-month trial is 260 kg/pellet, which is 16 kg/pellet higher than that produced during the 12 months prior to the trial (244 kg/pellet). Reduction in the heat input by eight per cent, from 727 MJ/tonne to 668 MJ/tonne. Reduction in bentonite rate by six per cent, from 7.1 kg/tonne to 6.7 kg/tonne. Increase in the furnace throughput rate by four per cent and additional production of 10 000 tonnes per annum through process stabilisation. Better understanding of the process behaviour. This knowledge is valuable not only for setting the target operating conditions but also for developing the ABM expert system to control the process.

Jan 1, 2005

By R Dunne, D Yan

In flotation where a bulk flotation concentrate is produced or a gangue sulfide such as pyrite contaminates a concentrate, residual collector has to be removed from the sulfide surfaces to allow selective separation in a subsequent flotation step. Depending on the sulfide mineral, the main species that needs to be removed when using a xanthate collector is either a metal xanthate or dixanthogen. For the identification of surface species, specific solvents may be used to remove each species û metal xanthates are known to be soluble in acetone whilst dixanthogens are known to be soluble in non-polar solvents such as diethyl ether. Xanthates break down with time, temperature and pH into various decomposition products. The major decomposition product is dixanthogen which can aid flotation but other products such as perxanthate and carbon disulfide can have an adverse effect on flotation. Various analytical techniques can be employed to monitor the formation of decomposition products on the surface of the mineral and in solution. The best of these is ultraviolet spectroscopy as it has diagnostic peaks for decomposition product determination. In this work two approaches were taken to understand the relationship between the flotation of a chalcopyrite and pyrite from an ore containing these two minerals. One approach was to remove the xanthate species with an organic solvent and then use ultraviolet spectroscopy to determine the concentration of dissolved species. The second method involved measuring xanthate decomposition in solution by measuring the residual xanthate concentration using ultraviolet spectroscopy. These experiments confirmed the species adsorb at the surface of the mineral and how these species affect the recovery and grade of the valuable mineral. In both cases pH and temperature were varied and two xanthate collectors (SEX and PAX) were used to study these relationships. These relationships could be applied to industrial flotation systems and allow for more accurate determination of optimal xanthate dosage and hence save on reagent costs.

Jan 1, 2005

By David S. Yantek, Paul Jurovcik, Eric R. Bauer

Workers in coal preparation plants, where vibrating screens are significant noise sources, are often exposed to sound levels exceeding 90 dB(A). The National Institute for Occupational Safety and Health, a major coal company, and a vibrating screen manufacturer conducted a cooperative study of vibrating screen noise. Rubber isolators reduced sound levels by 1 dB. Urethane screen panels did not reduce sound levels in this case. Drive noise was determined to be the dominant noise source on the screen. Damped side plates reduced vibration levels on the screen sides by 1 to 7 dB(A). Detailed results of the study are presented.

Jan 1, 2005

By J. Lu, J. B. Wiskel, D. G. Ivey, E. Niemi, H. Henein

Simulated TMCP using a Gleeble was undertaken to evaluate the effect of the austenite to ferrite cooling rate, coiling temperatures of either 400°C or 500°C and the magnitude of plastic deformation at the coiling temperature on the hardness of a Grade 483 (X70) steel. For comparable apparent cooling rates and deformation conditions, the hardness of the samples were independent of coiling temperature The application of a minimum compressive deformation > 8% was required to increase hardness at both simulated coiling temperatures of 400°C and 500°C. An increase in hardness was also observed with increased cooling times between 800°C and 500°C (i.e., slower cooling rates).

Jan 1, 2005

By R J. Goldfarb

Reduced intrusion-related gold deposits have become a new, low-grade, large-tonnage exploration target during the last decade. The best recognized examples of such deposits are recognized throughout the Tintina Gold Province of the northern North American Cordillera. Because such examples may have many features in common with orogenic gold deposits, such as anomalous Bi, W and Te, low salinity and CO2-rich ore fluids, and a spatial/temporal association with igneous rocks, confusion and controversy have now become commonplace in classification of many gold deposits formed along convergent margins. The best discriminators of IRGS are likely to be their: +        regional location in deformed shelf sequences on the inboard side of a series of accreted terranes and within terranes that also contain important tin and (or) tungsten deposits; +        local spatial association of gold ores with cupolas and contact aureoles of relatively reduced, alkaline-leaning, and volatile-rich plutons; +        post-deformational timing of gold deposition; +        extremely low sulfide content (commonly <1 vol %) of ores within igneous bodies and the outward zoning, through proximal skarns and to distal base metal-rich veins, from the causative pluton; and +        low grades (<1 g/t Au) of auriferous sheeted vein systems in pluton cupolas.

Jan 1, 2005

By K Hortin

Kidd Creek mine in north western Ontario is developing phase 1 of the deep mine project for mining between 2100 m and 3100 m below surface. Heat problems were experienced during the 2003 summer in working places about 2300 m below surface. At the time the mine had a æcold stopeÆ for cooling the air supplied to the mine below 1500 m from surface. The æcold stopeÆ is where during winter, ice is created in both the open pit and its connecting airways to the mine and used to cool air in summer. The operation and limitations of the existing cold stope were evaluated and led to the requirement for additional mechanical cooling to be available for the summer of 2004. The first stage of a surface refrigeration plant providing 7.5 MWR of cooling was approved, the compressor set was ordered in early January 2004 and the plant commissioned six months later in early July 2004. Based on the current modifications to the mining plan, further plant expansions are required in 2006 and 2009 leading to a total of 19 MWR of mechanical refrigeration and 8.5 MWR equivalent from the extended cold stope. The refrigeration system is described with emphasis on the specific adaptations necessary to suit Canadian conditions. Additional investigations were; using the refrigeration compressors in winter for heating and, extending the performance of either cold stopes or alternative ice storage systems. The winter use of refrigeration involve removing heat from the mine exhaust air to provide a cooling load and to use the hot water in the condensing circuit to heat the intake air and reduce reliance on mine air heating with natural gas. This paper follows on from an earlier one presented at the Seventh International Mine Ventilation Congress where the background and planning of the mine ventilation and cooling requirements were described for extending the mine at depth to 3100 m.

Jan 1, 2005

By Klaus Rieker

Over the last 30 years Wayss & Freytag Ingenieurbau AG has gained a lot of experience in mechanized tunnelling on various major projects. During this period most important developments concerning the machine technology for EPB- and Slurry-Shields have taken place. Since the first application of a hydro shield for the Wilhelmsburg Collector project in Hamburg in the early seventies, several stages of development have led to the current state-of-the-art in mechanized tunnelling. The continuous improvement of TBM techniques allows the execution of high quality tunnelling, particularly with regard to maximum safety and efficiency. The practical experience of the construction companies is of essential importance in order to continue further development and improvement.

Jan 1, 2005