Search Documents

By Zia Zafir

Design of the deep foundations for the loads imposed by lateral spread include the estimate of the pressure applied by the liquefied material as well as amount of anticipated displacement. In the absence of a non-liquefiable cover over a liquefiable layer, it is possible to design the foundation system just for the additional pressure applied by the flow slides. On the other hand, if a non-liquefiable layer exists above the liquefied zone, the foundation should be designed for anticipated movements. To completely account for liquefaction and/or lateral spread and their interaction with the deep foundation system, a coupled soil-structure interaction (SSI) analysis should be performed. However, a complete SSI analysis may not be feasible for most of the projects. This paper will present recent advances in analysis techniques and simplified methods to design deep foundations for liquefaction and lateral spreading. In addition, a case history of the Rancho California Bridge in southern California located within 1 km of the active Elsinore fault will be presented. One of the bridge abutments is underlain by potentially liquefiable layers. The pressure applied by the liquefiable layer was estimated to be greater than the shear capacity of the 36-inch CIDH piles designed for the abutment. However, with limited ground improvement and more careful analyses incorporating structural effects of CIDH piles, resulting design and construction resulted in a factor of safety greater than 1 against slope failure. The recommended approach was generally consistent with the recently published, and AASHTO sponsored, NCHRP 12-49 project regarding seismic design guidelines for new bridges and the effects of seismic displacements against bridge foundations.

Jan 1, 2006

By G. Danko, R. Tiwari, J. Knowles

Many excavation and loading tasks require equipment operators to simultaneously coordinate the motion of multiple machine links, in order to achieve complex tool trajectories. Efficiency, ore selectivity, and machine wear, are all affected by the skill level and attentiveness of the operator. A software-based kinematics reconfiguration system designed to assist operators with various tasks has been implemented on a small experimental excavator using our new differential control architecture. Kinematics transformation and feedback control algorithms are being developed and tested using computer simulation, and the results implemented on the experimental excavator. Several task-specific kinematics transformations, including a virtual revolute-to-Cartesian machine reconfiguration and computer-assisted bucket steering and stabilization have been successfully tested. Progress, challenges, results, expected benefits, and planned work are described.

Jan 1, 2006

By Alain E. Holeyman

After scoping out the objectives of this general report, the report reviews the three assigned main themes addressed by the papers submitted to the session: pile monitoring, testing, and data processing. It focuses on later developments and on issues requiring clarification, thereby identifying topics for potential discussion. Pile Monitoring does not bring much novelty, except for the integration of IT on construction sites. As far as testing, new developments focus on internal pile loading procedures while more confidence is being gained with dynamic and kinematic load tests. Significant advances are noted in the interpretation of data, where variability of results are coped with, loading rate effects are being better addressed, and more routine use of Finite element analyses are observed. Several many older problems remain while new issues emerge from more recent technologies and approaches.

Jan 1, 2006

By S. M. Flaherty, R. E. Scheffel, A. Guzman

Geochemical conditions within a leaching operation are heterogeneous. This variability arises mainly from hydrological controls imparted by physical characteristics of the ore and by heterogeneous metallurgical properties at the rock-fragment and industrial heap scale. The resulting chemical conditions are responsible for stratified mineral recovery, non-uniform extraction and prolonged leach cycles. This paper presents field data from a sulfide-leaching operation which clearly demonstrate the impact of chemical heterogeneity on metal recovery and the potential use of modern measuring techniques to facilitate operational monitoring and decision making for optimization of leaching operations.

Jan 1, 2006

By H. Vendette, N. R. Dando, A. Moras

The thorough analysis of results obtained from different testing campaigns performed on an alumina dry-scrubber pilot installation treating aluminum potline offgases, suggests a clear relationship between the emissions of gaseous fluoride and the fluoride saturation level of the alumina. The integration of this relationship into the development of a new generation of alumina dry scrubber represents an intriguing challenge regarding the design of more efficient air pollution control equipment. An innovative scheme challenging conventional industry practices was proposed. From theoretical simulations, the reduction in fluoride emissions can potentially be reduced by as much as 50% in the summer season. To validate this innovative approach, Solios in partnership with Alcoa Primary Metals, modified one of the Aluminerie de Deschambault's systems by adding new temporary equipment on the operating units and subjecting it to several test campaigns. This article presents the first results obtained in testing this new and innovative approach on alumina dry scrubbers used to capture fluoride emissions coming from aluminum electrolysis potlines.

Jan 1, 2006

By G. K. Mann

Fragmentation analysis of blast or crushed rock material is a time-consuming and costly process. During the last two decades, the mining industry has been investigating image-based analysis systems as an alternative to generate fragmentation results. Many image-based techniques and commercial products have emerged during the last few years, and the mining industry has recently begun using these tools for real-time estimation of size distributions. Some existing systems require manual image editing to add or delete edges (or net) before executing the fragmentation analysis routine. This manual procedure may take hours of time for each image analyzed. Reliable and robust image segmentation should be able to handle a wide range of rock textures and sizes under a variety of lighting conditions. This paper describes a novel software application, which has the capability to autonomously capture images and analyze them to generate the particle size distribution. The system can also process a batch of images captured during a fixed duration of time and produce the overall particle size distribution. The new method has different layers of segmentation modules, which allows the system to operate under a wide range of rock textures and lighting conditions. A new grey-level slicing technique is developed which can perform under a range of illuminating conditions. The Canny-based edge detection technique is used to segment rocks appearing in dark regions.

Jan 1, 2006

By Theo. A. M. Salet

The historic centre of one of the most beautiful cities in Northern Europe -Amsterdam - is being excavated to accommodate the new North/South metro line. This new line is due for completion in 2012, and will link the Buikslotermeerplein district north of the harbour, underneath the Central Station and the old city with its gables and picturesque canals, to the commercial centre in Amsterdam Zuid/WTC. Three underground stations are being construction in the old city at Rokin, Vijzelgracht and Ceintuurbaan. The logistics of working in the middle of an historic city are demanding -maintaining tram, vehicular traffic and pedestrian access along narrow streets, providing suitable protection for the public alongside the working areas, arranging adequate delivery routes, as well as monitoring the old and mostly historical buildings for potential settlement. Safety of both the public and adjacent properties is paramount. Diaphragm walling - 1.2m & 1.5m thick and up to 48m deep - was chosen as the support system for the three deep metro stations. Challenging engineering as well as state-of-the-art equipment to construct the diaphragm walls was needed in order to meet the tight working specifications, in the narrowest locations imaginable. Extreme conditions call for innovative solutions.

Jan 1, 2006

In the present work, the effect of pH, non-ionic polyacrylamide flocculant and anionic polyphosphate on rheology and settling behaviour of colloidal TiO2 suspensions (15 ? 50 wt% solid) is investigated. Maximum particle aggregation, reflecting in the highest suspension settling rate and maximum shear yield stress was achieved at pH 7.2, the isoelectric point (iep), consistent with DLVO expectation. However, the maximum aggregation condition at the iep also resulted in the poorest suspension consolidation behaviour. Significantly enhanced consolidation was achieved for a more dispersed suspension at pH values away from the iep but at reduced settling rate. Thus, when pH alone is used to control conditions which facilitate strong interparticle attraction, a high settling behaviour which is not conducive to compact consolidation results. Improved suspension consolidation may be achieved at the iep via anionic polyphosphate addition which leads to attenuation of the strongly attractive van der Waals forces and emergence of "soft" repulsion due to weak inter-particle electro-steric forces. The weak repulsion act to lubricate particles involved in the hydrodynamic interactions which controls the compressibility of the sediment bed, allowing a compact consolidation of solids to be obtained. Alternatively, non-ionic polyacrylamide homo-polymer (Magnafloc 333) was fairly effective in flocculating titanium dioxide suspensions leading to high settling rate and acceptable pulp consolidation at the iep.

Jan 1, 2006

By Yoshio Waseda

A laser flash method has been applied to obtain the thermal diffusivity values of Zr55Al10Ni5Cu30 alloy in the liquid, glassy, crystallized and supercooled liquid states. The electrical resistivity of this particular alloy was measured in the glassy, and crystallized states by a direct current four probe technique. A specific heat of Zr55Al10Ni5Cu30 alloy was also determined by a differential scanning calorimeter in the glassy state. On the other hand, thermal diffusivity values for two alloys of Zr60Al15Ni25 and Zr65Al7.5Cu27.5 were measured in the crystallized and liquid states. The thermal diffusivity values of three Zr-based alloys in the liquid state are summarized in the linear equations with positive temperature dependency and it is noted that the lower the thermal diffusivity values of Zr-based alloys at liquidus temperature, the lower the critical cooling rate to obtain metallic glass phase becomes. The thermal diffusivity values of Zr-based alloys were compared with those of Pd-based alloy case. These results suggest that thermal diffusivity of alloy liquids might be an indicator of the glass-forming ability of Zr-based and Pd-based alloys.

Jan 1, 2006

By M. Lahtinen

Traditionally, there have been three main methods for iron removal in the hydrometallurgical production of zinc. These methods are atmospheric precipitation of jarosite or goethite and pressurised precipitation of hematite. Jarosite precipitation is without doubt the leading and the most commonly used technology for iron removal. However, jarosite precipitation has some drawbacks, such as a low iron content (and, thus, high residue volume), high moisture content after filtration and often a high zinc content. These features make any environmentally acceptable way of using or disposing of jarosite more expensive, as compared to hematite and goethite. The importance of environmental regulations has grown in the zinc industry during the last decade, which will have an increasing effect on new investments. Hematite has several advantages over jarosite, such as a high iron content, low moisture and low zinc content. An important advantage of hematite is that it is suited for further use in the cement industry. However, until now the need for autoclave equipment has limited the spread and implementation of hematite precipitation in the zinc industry. Outokumpu Technology Oy has recently developed an alternative method for iron removal, which is the atmospheric precipitation of hematite. A patented method for precipitating hematite at atmospheric pressure is presented and compared with conventional methods for iron removal. The process conditions, the quality of the hematite precipitate and the environmental aspects are also discussed.

Jan 1, 2006

By Damien Wagner

To reduce the emission of greenhouse gases by the steel industry, particularly for ironmaking, the production of DRI (Direct Reduced Iron) using hydrogen as the reducing gas instead of carbon monoxide is being considered. In this context, the reduction of pure hematite by hydrogen was studied at the laboratory scale, varying the experimental conditions and observing the rate and the course of the reaction. All the reduction experiments were performed in a thermobalance and supplementary characterization methods were used like scanning and transmission electron microscopy, X-ray diffraction, and Mössbauer spectrometry. The influence of rising temperature in the range 550-900°C is to accelerate the reaction; no slowing down was observed, contrary to some literature conclusions. A series of experiments consisted in interrupting the runs before complete conversion, thus enabling the characterization of partially reduced samples. Interpretation confirms the occurrence of three successive and rather separate reduction steps, through magnetite and wustite to iron, and illustrates a clear structural evolution of the samples. Finally, the influence of the sample type was revealed comparing a regular powder, a nanopowder and a sintered sample. The regular powder proved to be the most reactive despite its larger grain size, due to a more porous final structure.

Jan 1, 2006

By A. Kaczmarek

As the mining industry is enjoying a much needed and long awaited increase in demand for natural resources, consolidations in both the mining and mining service industries and a generational departure of experienced industry professionals is challenging today’s mining companies, not only in maintaining their existing operations, but also in securing qualified resources for developing new projects. These challenges are compounded for junior mining companies, oftentimes lacking in operating properties to draw from for experienced professionals and having to compete with the majors’ “mega-projects” for experienced project personnel from the reduced ranks of engineering companies. This paper discusses some strategies developed by Anatolia Minerals Development Limited in developing its Çöpler Gold Project in central Turkey.

Jan 1, 2006

By G. B. Dukes

Scaling of rockpasses was problematic at Tau Lekoa Mine prior to production commencing in 1991. High horizontal stress levels relative to the host rock mass strength have been instrumental in causing the observed scaling. Scaling has been more pronounced in the deeper rockpasses and these are monitored regularly. Rehabilitation of one of the reef passes and one of the waste passes was required in the period 1999 to 2001. This paper describes the extent of the problems experienced to date as well as the rehabilitation completed.

Jan 1, 2006

By Peter (Yunqing) Zhang

Longwall recovery under weak roof conditions could have considerable delay if the immediate roof is weak and deteriorates during screening. A pre-driven longwall recovery room is a feasible solution to minimize the impact of longwall move on production. In this longwall recovery project, a 16-ft recovery room was pre-driven to cover screening, and the shearer cut another 16 ft outby to reach the final recovery line. The pre-driven recovery room was carefully monitored as the face was approaching it. The longwall face operated very well as it cut into the recovery room. The recovery process took about 13 days, and considerable time was saved compared with the previous panel. The support in pre-driven recovery room was designed to handle both front abutment pressure and weak immediate roof conditions. Pumpable standing support was used to support the cantilevered roof as the fender pillar narrowed and collapsed when the face cut into the recovery room. To ensure the stability of the recovery room, 3-D computer modeling was used to evaluate the support system. Abutment pressure, critical fender pillar width, bolting system, pumpable cribs and shield support were considered in the model. The recovery room was carefully monitored during longwall recovery. Roof-to-floor convergence and crib convergence were recorded every shift as the longwall face was approaching the recovery room. Roof, floor and pillar activities and crib performance were also observed as the face cut into the recovery room. This paper presents the support design for the recovery room, evaluation of the support system through computer modeling, and details of the monitoring results.

Jan 1, 2006

By V. Angelatou

In the present study, the possibilities of use of natural zeolitic tuffs from the Skaloma area, Rhodope prefecture, Greece, for the removal of Pb and Zn ions from aqueous solutions has been studied. The equilibrium data were examined for different grain sizes, pH?s and initial concentrations. An apparent kinetic study was also carried out for different time intervals at constant temperature and pulp density. For the chemical equilibrium study the Freundlich isotherm was used. The experimental results verified the favored behavior of zeolite on lead ions and the quick kinetic of the process whilst the efficiency of the ion exchange on zinc is rather limited. The grain size of the material did not greatly affect the performance of the process. The removal of metal ions worked better at lower pH. The Freundlich isotherms are in good agreement with the experimental data.

Jan 1, 2006

By A. R. Barnes, A. F. Newall

Keywords: Pyrometallurgy, furnace, smelting, spinel, PGM, phase diagrams As Merensky reef ores are replaced by UG2 ores, chromium levels in PGM smelting furnace feeds have steadily increased. Increased chromium levels lead to operating problems. Attempts to increase the chromium solubility in the slag by a variety of techniques create other difficulties. The authors have developed a technique for removal of the chromium spinel interface along with the matte for subsequent separation outside the smelting furnace by utilising differential solidification in the ladle. The process has been patented internationally with support from the Innovation Fund.

Jan 1, 2006

By Mahin Rameshni

WorleyParsons innovative SO2 reduction process efficiently recovers sulfur from SO2 streams. Effluent gases from ore roasters and smelters and coal-fired power plants can be treated to reduce sulfur emissions. This exciting new process is an innovative combination of well-established processes of reaction of CH4 and sulfur vapor to produce CS2, followed by catalytic hydrolysis of CS2 to H2S, and Claus reaction of H2S and SO2 to sulfur. Key advantages are lower fuel consumption, reduced emissions, better product sulfur quality and better operational stability. The Production of elemental sulfur from SO2 is being called Rameshni SO2 Reduction (RSR) and it is patent pending.

Jan 1, 2006

By H. Tutu

The legacy of gold mining operations continues to affect water quality in the Witwatersrand Basin in South Africa. The acid mine drainage (AMD) emanating from the tailings dumps liberates heavy metals from the ore minerals. The objective of this study was to characterise the geochemical processes that are important in understanding chemical evolution of polluted water in the study area. Analytical results for water samples collected in the catchment of the study area generally showed elevated concentrations of heavy metals in the vicinity of tailings dumps and mining operations and a decrease in the distal. Dams and wetlands, despite their proximity to the tailings dumps, recorded low concentrations of heavy metals and other pollutants. The characterisation of AMD was summarised in a conceptual model in which plots of redox potential versus pH and electrical conductivity versus pH were identified as the most important sub-models that captured the gross physical-chemical characteristics of polluted water and its interaction with the environment.

Jan 1, 2006

By R. Carrier

"There has been a continuous evolution with the use of pre-cast concrete elements in the construction of aluminum smelters. In 1990, Phase I of Alouette was built using cast-in-place concrete exclusively. Whereas, other AP 30 technology plants such as Hillside 2 in the mid-1990s used pre-cast concrete beams with cast-in-place floors. Mozal 2, in 2002, used pre-cast concrete beams with pre-cast partial-slab operating floors. Alouette Phase II went further. Not only were the potroom building beams and floors pre-cast, but the entire pot support system, insulating walls and basement jersey walls were pre-cast. Once the techniques for bending and welding the reinforcement bars and the design for attaching electrical insulating plates to the concrete was perfected, the challenge for the project remained only in the logistics of transporting the pieces to site and simple erection. The overall impact on the project was dramatic. Using prefabricated concrete not only allowed advancement of the schedule, but totally eliminated formwork, re-bar installation, and form removal activities along with the handling of all the materials involved with these activities. With the elimination of these labour and material-intensive portions of the job, exposure to work injuries was dramatically reduced. The most prevalent activity for lost time accidents is during the rough work associated with concrete formwork, placing concrete and form removal. Another area where prefabricated elements were successfully used on Alouette Phase II was for the insulating walls enclosing the pot area, known as the ""claustra walls"". Usually these walls are constructed in-situ using mortar and breeze block. Success was also achieved with prefabrication of the perimetric walls that are installed at the lower floor of the potroom. A big advantage of using prefabricated concrete in the electrolysis area is in assuring electrical isolation for the operating floors. Poured concrete requires a meticulous clean-up effort before commissioning to establish the electrically ""floating"" characteristics of the operating floors. Poured concrete results in ""wash"", stray wood,"

Jan 1, 2006

By Francis Vanbellen

Umicore Precious Metals Refining operates an integrated precious metals smelting and refining plant in Hoboken, Belgium. Once a smelter and refiner of complex concentrates, the plant today?s feed consists exclusively of industrial and consumer recycled products, making it the world?s largest recycling facility for precious metals. Unlike the fairy tale of the Frog Prince, it took much more than a princess? kiss to successfully realize this makeover. A completely renewed plant has been built over the past decade. The most visible technological innovation was the commissioning of the Pb-Cu smelter. Its flexibility towards very different types of feed makes it perfectly suited as main entry to the Hoboken flow sheet. A new Cu-leaching & electro winning plant and precious metals refinery make up the Precious Metals Operations (PMO) whose targets are fast throughput and maximized yields for gold, silver and the platinum group metals. The Base Metals Operations (BMO), flexibly process the by-products from the PMO, valorizing ?impurities? like indium, tellurium, selenium and others. Off gas and waste water treatments ensure compliance with strict environmental standards. Precious metals recycling is an art that goes beyond mastering a unique flow sheet. Umicore Precious Metals Refining offers a complete recycling service, taking care of sampling and assaying, metals management and logistics. The quality of this integral service is recognized through the attribution of ISO certifications for our operational activities, sampling and the environmental care. And it?s an art that follows Michelangelo?s experience: ?Art is 5% of inspiration and 95% of transpiration.?

Jan 1, 2006