Search Documents

By A. A. El-Midany, R. M. Farag, A. M. Salem, S. E. El-Mofty

Bentonite represents one of the main players in the stability of the drilling mud. Its particle size and particle size distribution affect the physical properties of the drilling mud especially the rheological properties. Therefore, a specific particle size distribution was recommended by American Petroleum Institute (API) for use in drilling mud. To clarify the effect of individual size and size distribution, in this study, the bentonite sample was classified into different size fractions. Each size fraction was tested separately in terms of controlling properties such as filtration loss, plastic viscosity, gel strength, cake thickness, and packing density. The effect of each size fraction on the rheological properties of the suspension was correlated to the behavior of the whole particle size distribution in the bentonite sample. The results indicate that the coarser the particles, the higher the rheological properties; in this case, the API mixture is the highest. The filtration loss and cake thickness for the API mixture are lower than that of the individual size fractions due to its wider size distribution due to the filling of voids between larger particles with smaller ones, which lead to bed compaction and consequently lower fluid loss and cake thickness.

By J. E. Dutrizac

Fracture-exposed surfaces of sphalerite samples having five different solid solution iron contents ranging from 0.0 wt% to 14.8 wt% Fe were leached for 15 to 120 s at 100°C in 0.3 M Fe(S04)1.5 -0.3 M H2S04 media. The reacted samples were examined using X-ray photoelectron spectroscopy (XPS) which provides chemical state information on the first few nanometers of the solid surface. Surface compositions show that the leaching rate increases with increasing solid solution iron content of the sphalerite. Detailed evaluation of high resolution S2p spectra show that the leaching progresses via the formation of polysulphide species. Disulphide species were not detected in any of the experiments. Examination of the Zn2p and Fe2p spectra indicate little change in the chemical states of these elements over the duration of the experiments. Longer leaching times resulted in the generation of elemental sulphur. The ratios of elemental sulphur to dissolved ferrous ions and zinc suggest that less than 5% of the sulphide is oxidized to sulphate. Morphological studies showed that the elemental sulphur commonly formed at a few isolated sites, such as the grain boundaries. Furthermore, euhedral sulphur crystals were often identified. These observations suggest that at least part of the elemental sulphur forms via dissolved sulphide species which are oxidized in solution by ferric sulphate.

Jan 1, 2003

By D. Diering

Having agreed to perform this task, I naturally started to wonder what on earth I was going to talk about, and on reviewing the literature I was surprised at how little I knew and how much I?d forgotten about the origins of this industry. For example: ?I?d forgotten that the Chinese invented black powder at least 1 000 years ago, back in the 10th century (although some say this invention occurred 2 000years ago). ?I didn?t know that Roger Bacon was the first person in the Western World to give exact directions for the making of gunpowder in 1242 and to understand its potential. Pepper?s Playbook of Metals quotes:?...above all, he is named as the discoverer of gun-powder, a material which has brought more wonderful changes in the great family of man than the most potent elixir that could have been devised to prolong life?.

Jan 1, 2000

The income of the Institute is derived from dues, subscriptions to Mining and Metallurgy and sale of publications. These sources are fortunately supplemented by the interest from invested funds now amounting to over $500,000, a considerable portion constituting endowments for especial purposes. Aside from the medal funds the principal endowments are the James Douglas Fund for support of the Library, the Rocky Mountain Fund and the Seeley W. Mudd Memorial Fund. The income from the two last named is available for the support of research and a variety of other purposes, It is allocated by the Board of Directors upon recommendation of standing committees in each case. An active effort is being made to increase the endowments of the Institute, it being felt that unusual opportunities exist for research and public and professional service through the organization and at a minimum of expense. J. V. W. Reynders is chairman of the Endowment Committee. Seeley W. Mudd Memorial Fund THE Seeley W. Mudd Memorial Fund, consisting of $100,000, was given the Institute in 1929 by the family of Colonel Mudd who had served the Institute as Director, Vice-president and on many important committees. His long career of distinguished professional and public service is fittingly commemorated by this fund. The income is available for support of research and other special purposes. In view of Colonel Mudd's life work with the nonferrous metals and his keen interest in the younger men of the profession it is purposed to apply the fund particularly to the benefit of these two. Control of income is exercised by the Board of Directors on recommendation of a Committee consisting of the President and Secretary, ex officiis, together with three others selected by the Board. The Committee consists at present of the following members: W. H. Bassett, President; H. Foster Bain, Secretary; Harvey S. Mudd serving until October, 1931; Edgar Rickard serving till October, 1932; George Otis Smith serving until October, 1933. On recommendation of this Committee the Board has authorized as a first project the preparation of a series of small books designed especially to be helpful to the Junior Members. These are now being written and it is hoped will be available for distribution in 1931. The list includes: A Brief History of American Mining, by T. A. Rickard; Mining Costs, Why and What, by Arthur Notman; Introduction to Mineral Economics, by H. Foster Bain and T. T. Read; Choice of Methods—A Record of Experience in Making Decisions, with chapters by W. H. Bassett, F. W. Bradley, E. DeGolyer, Howard N. Eavenson, A. B. Parsons, J. V. W. Reynders, L. D. Ricketts, Robert E. Tally, Pope Yeatman and others. One other book is projected but final selection has not been made. The purpose of these books is to afford the younger men who now come into a highly specialized profession some substitute for the broad

Jan 1, 1930

By Russell J. Foster

In this Bureau of Mines report a selection process has identified 14 nonstockpiled materials (cesium, gallium, hafnium, indium, osmium, rhenium, rhodium, rubidium, ruthenium, scandium, selenium, tellurium, thallium, and zirconium) that are linked to the continuing evolution of high-technology fields such as electronics, catalysis, and energy, and that have limiting factors associated with domestic availability. A qualitative assessment of the "potential criticality" of these materials was made through a consideration of end uses, demand trends and forecasts, production, mineral reserves, byproduct status, alternative supply sources, substitution and conservation options, and recyclability.

Jan 1, 1988

By Rosa G. de Pena

From the MAP3S Precipitation Chemistry Network data bank five years of data from January 1, 1977 to December 31, 1981 have been analyzed. No definite trend has been observed in the concentrations and the total depositions in the analyzed period. Comparison between the weekly and event samples show that the weekly samples could underestimate the total deposition. Preliminary results show that there is a reasonably good correlation between the precipitation composition and the emissions feeding the air in which the precipitation is formed.

Jan 1, 1983

By Fred Hodges

This paper describing the concentrator practice of the Hurley Plant of the Nevada Consolidated Copper Co. at Hurley, N. Mex., is one of a series of papers on milling methods and costs being prepared by the United States Bureau of Mines. The Hurley concentrator has a normal daily capacity of 13,500 tons of ore, and for the first four months of 1930 the heads of the concentrator averaged 1.32 per cent of copper and 3.14 per cent of iron. The recovery for this period was 83.98 per cent and the concentrates produced averaged 27.54 per cent of copper.

Jan 1, 1931

By D. C. Hilty, W. Crafts

A qualitative pseudoternary solidification diagram for the Fe-S-O system modified by manganese is proposed and supported by experimental derivation of an isothermal section at 1475°C and substantially 1 pct Mn in the solid-metal phase. The solubility of oxygen in liquid iron containing 1 pct Mn and sulphur contents up to 0.9 pct has been measured at 1600°C and found to increase as the sulphur content exceeds 0.15 pct. AS has been pointed out previously,' all oxide and sulphide inclusions in steel, excluding mechanically entrained matter, result from modifications of the basic Fe-S-O system. Therefore, one method of attack on the problem of the mechanism of deoxida-tion and inclusion formation is to examine the influence of deoxidizers on the Fe-S-O liquidus diagram. This approach has been adopted in work on the subject being carried out at the Metals Research Laboratories of the Electro Metallurgical Co. and has resulted in the postulation of types of solidification diagrams for the Fe-S-O system modified with common deoxidizers. This method has been of considerable assistance in interpretation of the factors affecting the formation of inclusions.' For the most part, however, these diagrams have been highly speculative. They were constructed primarily by inference from the pertinent binary and ternary systems and from the appearance of inclusions produced by specific deoxidizers. Moreover, since the systems contain four or more components, simplifying assumptions and qualifications were necessary in order to permit their representation as modifications of the Fe-S-O diagram. Consequently, experimental confirmation of the type of construction employed for these diagrams is desirable, and the present paper is concerned with such evidence. The addition of manganese to the Fe-S-O system was selected for initial investigation. Manganese is an important component of practically all steel and is, therefore, of fundamental interest. Because of its great affinity for sulphur, manganese has a more profound effect on the sulphide side of the Fe-S-O diagram than any of the other common deoxidizing eletments. In addition, more quantitative information pertaining to the contiguous binary and ternary systems involving iron, manganese, sulphur, and oxygen is available than for the other deoxidizers. Fe(Mn)-S-O Solidification Diagram Many of the side diagrams of interest in connection with this system are known. The Fe-Mn binary has been well established by several investigators;% the Fe-O system has been clarified by Darken and Gurry;' and FeO-MnO diagrams have been published by Herty,5 Andrew, Maddocks, and Howat,6 and by Hay, Howat, and White.7 The Mn-O diagram does not appear to have been derived experimentally, but the portion of 'it that is of interest can be visualized easily from a consideration of the melting points of Mn and MnO and the fact that a broad miscibility gap must exist between them. The ternary Fe-Mn-O diagram has been discussed by Benedicks and Löfquist,8 Wentrup,9 and by Körber and Oelsen.10 Experimental study of the Fe-Mn-O system has been carried out by Körber and Oelsen and to a lesser degree by Chipman, Gero, and Winkler,11 Hilty and Crafts," and others. On the basis of published information, then, an outline of the Fe-Mn-O liquidus diagram can be constructed as illustrated by Fig. 1. In this, as in all succeeding diagrams, transformations such as the ?-? reaction in iron have been ignored for purposes of simplification. The arrows denote falling temperature. The distinguishing feature of this diagram is the broad region of liquid immiscibility extending

Jan 1, 1955

By J Lane, D J. Barker, B Pei

Queensland Alumina Limited (QAL) is the worldÆs largest producer of smelter grade alumina, located in Gladstone, Queensland, Australia. The plant employs evaporative cooling towers for waste heat rejection. Process water requirements include red mud residue disposal, steam venting to the atmosphere and Calcination feed moisture. Raw (untreated) water consumption in 2001 was 37 700 m3/d or 3.8 m3 per tonne of production. The Gladstone region experienced a water shortage in the period 2001 to 2003, resulting in progressive water restrictions. Industry operated under a ten per cent restriction from April 2002 and in November 2002 a 25 per cent restriction came in force. The maximum restriction level of 50 per cent was anticipated for the middle of 2003. Water restrictions of these magnitudes have the potential to result in significant production limitations, which would have major economic consequences for QALÆs owners, customers, suppliers and employees. Therefore it was imperative that measures be found to mitigate the impact of these restrictions. Furthermore, as one of the largest water users in the Gladstone region, QAL had an obligation to the community to minimise water usage as much as possible. A thorough analysis of water usage on site was conducted, focussing on all water streams leaving the plant. The philosophy used was that by minimising water outputs, the inputs would follow suit. Where possible, preference was given to solutions that provided lasting water savings. This occurs when the value of the water saving justifies the project cost, irrespective of water restrictions. By June 2002 an average water saving of 19 per cent was achieved, almost double the required saving. By end November 2002 further projects had increased the total water saving to 29 per cent, mainly through the re-use of GladstoneÆs municipal treated effluent as wash water. Further measures to reach the target of 50 per cent reduction were investigated. The evaporative cooling system was to be replaced with seawater cooling, using cooling towers to minimise the seawater pumping cost. Another benefit of this concept was the ability to dispose of the cooling tower bleed stream with the existing system for neutralised red mud disposal. This would avoid the need for an additional environmental outfall from the plant. In February 2003 the Gladstone region received over 500 mm of rain, which boosted water reserves to five years supply at forecast usage rates. This led to the lifting of all water restriction. As most of the implemented water savings measures are economically viable in the absence of water restrictions, raw water usage at QAL is still less than 75 per cent of pre-2002 levels.

Jan 1, 2003

Purpose of TSUG Continuous Improvement in Mining Share Best Practises Exchange Ideas Network for Frontline Supervisors and Middle Management Meetings ? Two per Year -Spring and Fall ? Thirty Five to Forty Attendees ? Rotate Between Host Properties ? Host Mine Provides ? Meeting Room for One Day Tour of Mine and Maintenance facilities on Second Day

May 1, 2010

By M. Semchyshen, G. A. Timmons

The predominant orientation in both straight-rolled and cross-rolled molybdenum is the {100} [110] texture. Upon complete recrystallization, this same texture predominates, but there is less spread about the ideal orientation. A secondary orientation about the [111] direction as the axis develops in cross-rolled sheet. Compression-rolled sheet exhibits random orientation in the plane of the sheet. Some mechanical properties were measured at varying angles to the rolling direction to determine the effect of preferred orientation on anisotropy in molybdenum sheet which had been straight, cross, or compression rolled. THE development of the arc-cast process has made available large ingots of molybdenum from which it is possible to roll sheet of considerable size. It is anticipated that such sheet will be further fabricated by spinning, drawing, stamping, or forming. Anisotropy of physical properties caused by the preferred orientation developed in the sheet during rolling may be expected to affect the behavior of the metal when subjected to these fabricating operations. To produce a sheet which will be most amenable to the fabrication of a given shape by a particular operation, consideration should be given to the directions and magnitudes of plastic deformations produced in the operation. When possible, the rolling schedule should be controlled to develop a texture which favors the required deformation. The existence of preferred orientations in rolled molybdenum sheet has been reported by Jeffries,' Konobejewsky,' Fujiwara," Goss,' and Ransley and Rooksby." None of these investigators obtained sufficient X-ray data to permit the construction of pole figures; instead, they based their conclusions upon Debye-Scherrer patterns of a limited number of positions. Ransley and Rooksby devoted some attention to transcrystalline cleavage at 45" to the rolling direction, indicating that it is appreciable in polycrystalline material only when the crystals are in the ideally preferred condition, and that this condition is only approached if the metal has been rolled successively in two perpendicular directions. In a recent paper, Custers and Riemersmao introduced the first pole figures to describe the textures of straight-rolled and cross-rolled molybdenum sheet. To increase the knowledge concerning the generation and effects of preferred orientations in molybdenum sheet, an investigation was undertaken to determine the effects of variations in rolling schedule and annealing treatments on preferred orientation, and to correlate preferred orientations with some mechanical properties. The orientations of straight-rolled, cross-rolled, and compression-rolled sheet have been determined by X-ray analysis, both as-rolled and after recrystallization. Pole figures have been constructed to describe the textures produced by these various rolling procedures. Texture of Cast Molybdenum Ingots In the arc-cast process, molybdenum powder is pressed into a vertical column which is sintered to increase its strength as it proceeds downward into a water-cooled mold, where the metal is melted in an alternating-current arc established between the end of the formed powder electrode and the metal bath at the top of the growing ingot. Since the solid-liquid interface moves continuously upward in the mold, the crystal axes are not normal to the cold surface of the mold but have the curvature shown in Fig. la. X-ray analysis reveals that the cube axis is the fiber axis and that it is normal to the cold surface of the mold; that is, the [loo] direction is parallel to the longitudinal axis of the ingot. This substantiates recent work by

Jan 1, 1953

By Irving Hartmann

As part of the continuing effort by the Bureau of Mines to promote mine safety, research work is being conducted at the Experimental coal mine, Bruceton, Pa., on the prevention of coal-mine explosions and on other mine-safety problems. The principal subjects studied during the past 2 years are briefly described in this paper. Although at present these problems are relevant particularly to the mine layout and to high-speed mining practices in numerous American coal mines, it is hoped that the findings will prove interesting and useful also to our European research colleagues. Some of the investigations treated here will be presented in greater detail in forthcoming Bureau of Mines reports. 1. UNDERGROUND STORAGE OF COAL CUTTINGS The seams in mist American bituminous-coal mines are undercut, shear-cut, or top-cut before blasting. The cuttings arc generally loaded out with the balance of the coal. However, in some mines it is not economical to load and remove cuttings from the mine. This applies especially if the cut section of the seam is of appreciably lower grade than the rest of the coal, or if the cut is made partly into an adjacent stratum that is high in incombustible content. In such mines the cuttings are sometimes stored in random heaps in rooms or other areas, along the ribs of mine entries, or in layers on the floor of rooms or entries.

Jan 1, 1956

By Jan Klein

"The last decade of the 20th century saw the development of one of the last missing geophysical tools for mineral exploration: the Airborne Gravity Gradiometer. It is possible that Airborne Induced Polarization, one of the stillelusive systems, will make its debut in the next few years. In this sense, the paper point out are the most recent and important improvements in geophysical technologies for mineral exploration. Airborne techniques are followed by the systems used on the ground and in boreholes. New equipment and data processing and modeling software are referred to. Brief remarks are made about developments that can be expected in the years to come, these will be mainly focussing on deep search in rugged and conductive terrains. "

Apr 24, 2001

By Mark E. Smith

To allow recovery of gold values from ore which cannot be economically processed by the mill, Pinson Mining Company has developed a run-of-mine heap leaching facility. In order to estimate production scale recovery rates, reagent consumption and percolation problems, a series of pilot scale tests were performed. These tests typically consisted of 3,630 metric tons (mt) (4,000 tons) leach ore at a grade of .94 to 1.56 grams per metric ton (g/mt) (.03 to .05 oz.) Au/Ton. Test heaps were loader stacked to approximately 4.3 meters (14 feet) high. Information from these pilot scale tests was employed in the design and construction of the production scale facility. Parameters such as spray rate, leach cycle, sprinkler placement, and barren solution chemistry were determined by the pilot tests.

Jan 1, 1983

By J. W. Galpin, V. L. Minear, F. C. Sturges, B. H. Mott, R. H. Allen, W. W. Weigel, Wm. D. Owsley, R. E. Moeller

By definition the word "grout" means a thin mortar, or a kind of plaster or ce¬ment, and "grouting" means to fill up or finish with grout. The words "cement," "plaster" and "mortar" mean a substance that is used in a soft state which subsequently hardens. Thus, grouting is the filling of void space with a substance that hardens. Construction cements are the most common substances used, either by themselves or in mixtures, but the term grouting is applied quite correctly when other substances such as plastics and certain chemicals are used. Also, the use of the term grouting to cover the filling of voids with materials that do not actually become hard, such as the-flotation tailings used in grouting in the southeast Missouri lead district, should be considered correct, as some stiffening does take place and, anyway, it is a better descriptive term than any substitute. Engineers are interested in grouting because some of the materials with which they must work contain voids, and certain conditions can be improved if these voids can be filled with something solid and permanent. Grouting is done to accomplish several purposes: I. To stop the passage of fluids and gases, 2. To cement materials together to make them stronger, and 3. To prevent consolidation of materials by filling void space with something solid as a replacement for the air and water that could be forced out under load. The construction industry uses grouting extensively for all three purposes. Grouting is used to stop water percolation under and around dams. It is used to control water flow in tunnel driving and in shaft sinking. It is used to improve foundation conditions under civil engineering structures by permanently filling void space and thereby reducing settlement, or by cementing broken rock together and increasing its supporting strength. The oil and gas industry does a lot of grouting, primarily to stop the passage of gases and fluids. The search for oil at increasingly greater depths has meant greater investment per well, and the oil industry has spent large sums on development of improved drilling methods. This

Jan 1, 1948

By B. M. Larsen, T. E. Brower

An increasing amount of attention is being paid to the possible influence of oxygen, in its several modes of occurrence in steel, upon some of the properties of the metal; but clearly investigations along this line are unlikely to yield significant results until reliable analytical methods for the determination of oxygen have been established. This paper presents some results of a study of an improved Ledebur method which aims to determine a definite portion of the oxygen; namely, that which presumably is present in diffusible form in the solid steel. These more or less preliminary results lead us to believe that the oxygen so determined has some significance; their presentation at this time will, we hope, stimulate discussion of, and focus attention upon, certain rather neglected aspects of the problem. Considerable work has been done recently on methods of estimating inclusions and on the vacuum-fusion method for oxygen; with results which, however, are of somewhat questionable significance. It is commonly presumed that the oxygen in a bath of molten steel in a furnace is present partly as a separate phase consisting of suspended particles of oxides or silicates, partly in solution, the latter being probably the more important. Upon addition of a deoxidizer, it reacts with some portion of the dissolved oxygen and precipitates it as additional suspended particles; the oxygen not eliminated in this way, which remains in solution in the liquid steel, may be regarded indifferently either as dissolved oxygen or as dissolved FeO. When the steel is poured, some of the suspended particles rise towards the surface, others remain trapped in the finished steel, appearing as nonmetallic inclusions in amounts corresponding usually to about 0.01 to 0.03 per cent Oz in the steel. The dissolved oxygen may be partly eliminated as CO during freezing of the ingot, but some remains either in solution or in part precipitated as FeO. Finished steels may thus contain oxygen in several forms: (1) In non-metallic inclusions which are probably quite insoluble in the solid metal at all temperatures; (2) in solid solution which at lower temperatures may be supersaturated; (3) in FeO particles produced by relief of this

Jan 1, 1932

By H. M. Conger

I'm really very pleased to be talking with you today about the environmental impacts of gold ore processing as part of this symposium on emerging process technologies for a cleaner environment. But before I talk about some of the newer developments that are coming, I would like to set the stage by reviewing some of the recent past. Over the last decade or so the U.S. gold mining industry has experienced remarkable growth, primarily in heap leaching operations, and not surprisingly there has been parallel growth of environmental regulations. At Homestake, we have had the excitement of bringing on-line a new mine embodying state-of-the-art technology and environmental planning, and during the same period the flagship of our company, the Homestake mine, has been brought into modern day compliance through the application of innovative environmental technology. This has been a learning process; in both cases we found that we had to develop new ways to meet our objectives. At our McLaughlin mine in California a major achievement was pioneering the use of pressure oxidation, or autoclaves, for refractory gold ores, and at the Homestake it was the development of a unique bio-treatment plant for wastewater. These projects were developed balancing operational goals, environmental concerns and costs, and I would submit that being cost-effective is our greatest challenge in the development of new, environmentally sound, process technology. In meeting that challenge, our job has not been made any easier by the myriad environmental laws and regulations that directly affect the design and operation of our facilities. Most of these constraints have evolved through the political process more or less independently, but in their application there often are over-lapping provisions. Adding to this complexity is the fact that action takes place in both state and federal arenas. As a result, state and federal roles sometimes become intertwined, and a good case in point is provided by various cyanide issues faced by gold producers. The vast majority of U.S. gold mining takes place in the so-called "mineral States," the western States that come under the Mining Law of 1872 as amended. This is the basic statute that provides for access and tenure to develop mineral resources on federal lands in those states. There is gold mining outside the defined mineral States, and there is also gold mining in the mineral States on private lands. Our own Homestake mine in South Dakota is one of the best examples of the latter category: located entirely on private land, it is nevertheless subject to at least 13 federal environmental statutes and some 29 federal regulatory requirements. There are also nine significant state statutory and regulatory requirements that apply. On federal lands in the mineral States there are numerous federal statutes and regulations which affect mining, over and above the current Mining Law. These, which are in addition to the laws applying to private land, include the National Environmental Protection Act and the Federal Land Policy and Management Act, among others. Still, those who advocate radical changes in the basic Mining Law would have us believe that sweeping environmental protection and reclamation provisions, not to mention new land use restrictions, are needed. Such changes could effectively prohibit mining on the federal public lands. Strict enforcement of our current Mining Law would have presented most of the abuses cited by the critics but if the Law is to be changed at all, I believe that, at a minimum, the principles of self-initiation and security of tenure embodied in the present statute should be maintained. These are critically important concepts, but there are other statutory and regulatory issues constantly before us as gold miners. Let me cite a few examples: Reauthorization of RCRA There are several bills being considered by Congress to amend the Resource Conservation and Recovery Act (RCRA) that have as their theme

Jan 1, 1992

By W. P. Roux

With depletion of higher grade iron ore reserves, and the need to process finer, lower grade material; there is a need to better understand the recovery efficiency of jigging process. The use of Positron Emission Particle Tracking (PEPT) was examined as a technique, to study the motion of particles inside a laboratory batch jig. PEPT is a noninvasive method that can provide three dimensional kinetic data of a particle during jigging. Particles with different densities and sizes were traced under the same jigging parameters, to obtain a data set that can be used for the development and verification of jigging models. From the results, detailed information on the stratification rate of a particle was obtained, with adequate resolution to see particle movement through an individual pulse. Detailed data of this nature is critical for the validation of CFD and DEM models. Keywords: positron emission particle tracking, jigging, jig models

Sep 1, 2012

By Ranford LC

Modern, research-based approaches to mineral exploration are essential to the future maintenance of the mineral industry. These need to fully utilise the rapidly expanding growth of understanding of the evolution of the earth's crust, and be properly integrated with advances in understanding of chemical and physical processes involved in ore formation. BMR has a major role to play in supporting the growth and utilisation of this research base, as well as maintaining the national geological and geophysical bases which are essential both to tactical and strategic interests of Australia and of its mineral industry. The objective development of data-process modelling is one target of such strategic research based on a more integrated approach to research by BMR, mineral companies, CSIRO and the universities with emphasis given to promoting positive feedback during research activities. Examples of the success of strategic research in Australia and overseas are noted in the Text.

Jan 1, 1986

By Michael W. Hinds

X-ray Fluorescence Spectrometry (XRF) is used at various stages of gold refining. Initially, incoming impure gold is analysed for deleterious elements such as As, Cd, Hg, Se, and Te. Based on the levels of these impurities the material can be returned to the client or accepted for refining. XRF is also used to determine the metal concentrations after the impure gold has been melted and sampled. This information is used to assist the final Fire Assay determination of gold and silver. An energy dispersive XRF is used to determine the end point of chlorination refining step.

Jan 1, 2011