Search Documents

By Thais Cristina da Costa Caldas, Carlos Mauricio Fontes Vieira, Alline Sardinha Cordeiro Morais, Sergio Neves Monteiro

"This work has as its objective to evaluate the effect of the incorporation of a glass powder waste obtained from discarded and Hg-cleaned fluorescent lamp into clayey ceramics used to fabricate bricks and roofing tiles. Formulations were prepared with incorporation of the waste in amounts up to 10 wt.% into the clayey body. Rectangular specimens were prepared by uniaxial mold-press at 20 MPa to fire at 850 and 1050°C. The physical and mechanical properties evaluated were: linear shrinkage, water absorption and flexural rupture strength. The microstructure of the fired ceramics was evaluated by optical microscopy. The results showed that the waste incorporation significantly improved the evaluated properties mainly at 1050°C.IntroductionFluorescent lamps use mercury as a main component for its operation. This metal is potentially toxic and can contaminate soils, animals and water bodies. The problem is aggravated if considerations are made with respect to the amount of lamps that are commercialized and discharged in emergent countries like Brazil [ 1].By using appropriate recycling processes applied to discharging fluorescent lamps it is possible to reuse most constituents of these lamps into new productive processes. A study has shown that one million common fluorescent lamps can generate 900,000 tubes of clean glass [2]. Moreover, this Hg-cleaned gloss may be recycled in different products.In fact, to recovery and recycle all materials that constitute the lamp instead of discharging them. This action protects the soil avoiding the formation of environmental passives [3]. It is also relevant to mention that the glass from fluorescent lamps is 100% recyclable while its permanence in the environment would correspond to very long time pollution, since its decomposition time is undetermined [4]."

Jan 1, 2011

By R. Alarcón Sch., R. Abel F.

For many years, copper cathode quality has been a priority for end consumers, since it affects the variety of products that can be obtained from them. From the beginning, physical and chemical quality of the wire bars was controlled, as this product was used to obtain wire rod and other forms of copper by wire drawing. At that time, all the electro refined cathodes were melted and casted as wire bars. Subsequently, in the 80’s, with the introduction of continuous casting furnaces, it was possible to directly produce wire rod from cathodes. From then on, cathodes quality standards were consistently increased, by the introduction of uniform criteria, among which we can identify ASTM and British Standards as well. Also, producers began to use more demanding internal standards than the existing specifications, in order to differentiate their cathodes as high quality products among customers. Today the physical aspect of cathodes, including nodules, cracks, sulfates, or others, is the first element used by end customers to assess their quality. This paper aims to show a brief vision of the evolution of quality specifications for products used to manufacture copper wire. INTRODUCTION From the beginning of refined copper production for industrial purposes, mandatory minimum quality conditions were established. These quality conditions were used as the main element to determine prices and discounts of the respective sales contracts. Reviewing the copper development history, we can appreciate that its quality requirements had been constantly evolved, so that currently refined copper has an extremely high quality standard, that allows its direct use in the production of ultra-thin cables and other products applied in the industry. In each stage, refined copper production has fostered the development of technology used in their treatment. Similarly, cathode processing technology has been evolving to minimize treatment costs in order to generate a wire rod for several uses, ranging from power cables to super conductors. In this sense, to the already known type of fusion processes of the Southwire or Asarco type (capacities over 80 kt / year), wire rod production processes of the Upcast or Rautomead type (capacities between 20-50k t / year) have been added. They immediately deliver oxygen-free wire rods. In both cases, we can conclude that the clients' requirement had evolved from a chemical criteria focus, to considering more subjective aspects, such as visual control as the first stage of inspection.

Jan 1, 2019

By X. Yuan

"The processing behaviours of ores such as their liberation characteristics in comminution and their response in separation processes are affected by their mineralogical characteristics. Key ore characteristics which are relevant to processing, such as mineral proportions, mineral grain size, grain shape and mineral associations are routinely measured at the micro-scale in polished section using optical microscopes and SEM-based automated mineralogy systems. The application of X-ray micro-tomography to mineral processing provides the means to quantify these important micro-textural characteristics in three dimensions, removing the stereological issues encountered when measuring volumetric information in two-dimensional polished sections. In this paper we present several examples of ore textures to illustrate where X-ray micro-tomography can be applied successfully to obtain quantitative measures of ore characteristics which are useful in a variety of process modelling applications.INTRODUCTION X-ray tomography has been used as a tool in medicine for some years and is being applied in a wider range of fields including geology, palaeontology and mineralogy. In this paper we present some applications of X-ray tomography in mineral processing applications being developed at JKMRC. The availability of SEM-based automated mineralogy systems such as MLA and QEMSCAN has seen the increased use of quantitative mineralogical data measured in two dimensions in the design, operation and simulation of mineral processing plants. When the ore is amenable to measurement by X-ray tomography this technique can provide quantitative data for characteristics such as mineral grain size, shape, mineral associations and liberation in three-dimensions. The advantage of measuring these characteristics in three-dimensions is that the stereological issues which bias measurements made on polished sections are removed. X-ray tomography also quantifies the location of mineral grains relative to one another in space - a useful descriptor of ore texture. Like many measurement techniques X-ray tomography has advantages and disadvantages when compared to other techniques. One limitation is that the ability of the X-ray tomography system to discriminate between minerals is a function of the X-ray attenuation of those minerals. While the X-ray attenuation of many common minerals is sufficiently different for X-ray tomography to distinguish between them, there are some where the overlap in X-ray attenuation makes discrimination on the basis of this characteristic alone impossible. An example of this would be chalcopyrite and magnetite. However where the ore mineralogy is suitable to apply X-ray tomography, the technique provides some exciting opportunities to explore the relationship between texture and ore processability."

Jan 1, 2012

By Ronald B. DeDiemar

It is generally held that cone crusher application technology is strictly an art and thus subject to the vagaries of emphirical and/or trial and error judgments. While this is basically true, certain factors have been identified which, when properly defined, can significantly reduce the element of chance. This paper will bring out these factors as well as pointing out other technologies available to predict and/or analyze cone crusher performance.

Jan 1, 1977

Research on the Design and Processing Characteristics of 320 m3 Air-Forced Mechanical Flotation Cell

Sep 13, 2010

By Essie Esterhuizen, Michael M. Murphy, Chris Mark

"The design of underground coal mines requires a clear understanding of the overburden response, the loading of pillars, the loading of the gob, the pillar failure process, and the ultimate load carried by partly or fully yielding pillars. Very few highquality stress measurements of yielding pillars and gob loading have been made in full extraction mining. Well-calibrated numerical models can assist in providing a better understanding of the load and failure processes, provided the coal, the overburden, and the gob are all modeled with sufficient realism. A program of numerical model calibration and validation was carried out using FLAC3D.1 The models were calibrated against observed and measured performance of coal pillars and the overburden in operating mines to provide a basic set of input parameters that can be used to provide a realistic first estimate of expected ground response and pillar loading. Input parameters for modeling coal pillar response were based on data from triaxial testing on coal samples, combined with both matching the depth of failure in the coal ribs to observations as well as matching the peak pillar resistance to an empirical equation. The models were calibrated against strong roof and floor case histories in which the pillar strength is governed by failure and yielding of the coal within the pillar and the surrounding strata only had a limited impact on pillar strength. Input parameters for the overburden were determined from a large database of laboratory tests and model calibration against maximum subsidence and subsidence curvature. Further overburden calibration was carried out by matching stresses in the mining horizon to field measurements. Three examples of the application of the calibrated dataset and modeling methodology to field measurements are presented. The results show that a reasopable estimate of the in-seam stress distribution and overburden response can be obtained for both strong and weak overburden scenarios at various depths of cover.INTRODUCTIONThe planning and design of coal mine excavations requires reliable estimates of the expected strength and loading of the mine structures to achieve global stability. Empirical methods are widely used to estimate the strength and loading of coal pillars and have been incorporated into pillar design procedures, such as Analysis of Longwall Pillar Stability (ALPS) (Mark, 1987) and Analysis of Retreat Mining Pillar Stability (ARMPS) (Mark and Chase, 1997), that are widely used in the United States. ~umerical models are finding increasing application as a tool for underground mine design because of their. versatility and the ever increasing computational power available to mine designers. A prerequisite for the application of numerical models is the calibration of the models against observed rock mass response (Hoek et al., 1990; Skiles and Stricklin, 2009). The calibration process may include comparison of model results to measured stress and deformation and modifying the input parameters in a systematic manner to achieve a satisfactory agreement between the model results and measurements. Once models have been calibrated, they can be applied to evaluating similar mining layouts in similar geological conditions."

Jan 1, 2010

By Susumu Tsubota

Three types of reference gold catalysts, i.e., 3wt%Au/TiO2 (Au-Ti: Type A), and 0.3wt%Au/Fe2O3 on alumina beads (AUS: Type B), and 5wt%Au/Fe2O3 (Au-Fe: Type C), were produced in a test plant scale by Sud-Chemie Catalysts Japan, INC. under the licensing of AIST. To evaluate the validity of the preparation methods and conditions used for the reference samples, elemental analyses by ICP, particle size measurements by TEM, and catalytic activity measurements for the oxidation of CO and H2 over these catalysts were made. Gold catalysts can be prepared in a large scale of ca 400g for the Au-Ti and Au-Fe catalysts, 5 kg for the AUS catalyst with good reproducibility. It was confirmed that they were available for useful as the reference gold catalysts of World Gold Council.

Oct 1, 2003

In longwall mining, premining prediction of methane emission rate depends on a number of geological factors, geographical factors, and operational factors. These same factors also can impact the selection of a specific degasification system. This study proposes a principle component analysis (PCA) and artificial neural network (ANN) approach to predict the ventilation methane emission rates of U.S. longwall mines and the optimum combination of degasification boreholes based on the given characteristics of the mine. Artificial neural networks, more than conventional computer models, are adaptable systems that can solve problems such as non-polynomial or very complex relationships that are difficult to describe mathematically. Data on ventilation emissions and degasification system design were obtained from 63 longwall mines in 10 states and were combined with corresponding geological, geographical, and operational parameters for the period 1985-2005. PCA was used to determine the variables that most influence ventilation emissions and degasification system design. Different combinations of variables in the data set and network structures were used for network training, cross-validation, and testing. The resultant ANN models predicted ventilation methane emissions with a 90-95% accuracy and were superior to multi-linear and second order non-linear models. The ANN-based expert classification system was able to classify the design of the degasification system (no degasification, gob vent borehole, horizontal and gob vent borehole, and horizontal, vertical and gob vent borehole) with more than 80% accuracy. The models can be used as prediction and decision tools for the ventilation emissions and degasification system selection for specific site and mine-design conditions.

Jan 1, 2009

By M. J. Scoble, W. J. P. Leigh

This paper aims to characterise the forms of slope instability incident in surface coal mines in Britain. These are related to observed controlling factors, with particular reference being given to slope geometry and structure. The work is based on specific data collection programmes considering actual stable and unstable mine slopes. Reference is made to field examples.

Jan 1, 1982

By G J. Halstead, R C. Steinhaus

The True Pipe® in-line sampler was developed in an attempt to address the need for a mechanically reliable and correctly designed sampler to suit one-dimensional pressurised slurry pipelines, often found in metallurgical process plants but for which no reliable and representative sampling solution as yet exists.The design, whose operation is based on the principle of symmetry, is described by Dominique François-Bongarçon (2005) with the synchronous opening and closing of relevant valves. It representatively isolates portions of the particulate material stream at predetermined intervals for effective extraction of primary increments for subsequent sample compositing.Theory of Sampling applicable solutions have proven elusive in flowing pressurised particulate material streams, with various attempts to date not having formulated a viable, mechanically reliable and acceptable design.Compliance to sampling theory is critical, and a number of tests were conducted where certain operating parameters were altered to determine their influence and sensitivity on sampling representativeness.The results of the initial series of tests performed on a carefully designed rig are presented, with additional work discussed for necessary investigation in the near future.Getting closer to a robust, economic and correct design for this challenging application in the minerals industry may now not be that far away. Plant management staff will see improved metallurgical mineral balances around their process plants and significantly reduced sampling discrepancies, particularly in tailings applications. Improved quality control is now possible where, due to plant head room constraints, classical cross stream sampling methods cannot be employed.CITATION:Steinhaus, R C and Halstead, G J, 2014. True pipe sampler – a correct design utilising the principle of symmetry in pressurised slurry particulate streams, in Proceedings Sampling 2014 , pp 127–134 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

This paper will first discuss the fundamental requirements for reliable discharge of backfill by gravity alone at high per cent solids. This discussion will include brief mention of the underlying principles of saturated solids flow contrasted to that of stirred tank or dilute discharge systems. Here the need to possess full knowledge of the flow properties of the stored material will be highlighted. In addition proper account must be made of the silo overflow weir and settling capacity to match plant throughput. Here opportunity will be taken to highlight the complexity of this multi-phase flow situation as well as the general yet paramount requirements for reliable solids flow. It will be shown that by proper attention to the multi-phase considerations gravity discharge of slurries as a consolidated bed with minimal water content is possible. Such high solids discharge results in greatly reduced demand for process water. In addition pumping costs are reduced as is the delay time associated with the mine drainage operation. Confirmation of successful applications will be highlighted by reference to several recent case studies. In the concluding phase mention will be made of the key yet very simple and effective operation techniques which enhance reliable discharge. The simplicity and reliability of properly designed gravity discharge backfill tank systems suggests increased application of this technology by the mining industry.

Jan 1, 1998

By Thomas E. Leontis

INTRODUCTION THE importance of magnesium alloys in the manufacture of aircraft engines has been realized for many years. A concentrated effort has been exerted in the laboratories of the Dow Chemical Co. to develop magnesium-base alloys with improved properties at elevated temperatures whereby greater advantage can be taken of the inherent lightness of these materials. In an earlier publication,1 attention was called to the superior tensile properties and resistance to creep of cerium-containing magnesium alloys at temperatures up to 700°F. More recently, additional data on magnesium-cerium alloys have been furnished by Murphy and Payne.2 The present paper deals with the mechanical properties of sand-cast magnesium alloys containing zinc, at temperatures up to 500°F. The study includes binary Mg-Zn† alloys containing up to 10 pct zinc and several ternary and some polynary alloys based on the Mg-1Zn,†Mg-3Zn, Mg-4.4Zn, Mg-6Zn, and Mg-10Zn binaries. The compositional variation in the tensile properties, hardness, and creep at room and elevated temperatures, and in the electrical conductivity at room temperature has been determined. The results of these tests show that many zinc-containing magnesium alloys exhibit resistance to creep at elevated temperatures significantly higher than that of present commercial magnesium alloys, but lower than that of alloys of the magnesium-cerium type. In addition, they have high tensile properties at room and elevated temperatures and high conductivity. This combination of mechanical properties and conductivity indicates that these alloys should be given serious consideration for commercial applications involving exposure to temperatures higher than those to which present commercial magnesium alloys can be taken safely. LITERATURE The properties of sand-cast magnesium alloys containing zinc as a principal alloying element have not been investigated very extensively, especially at elevated temperatures. The following remarks, which are confined to sand-cast alloys, will serve as a summary of the most important references on this phase of magnesium metallurgy. The first recorded determination of the tensile strength of binary Mg-Zn alloys as a function of zinc content was reported by Aitchison.3 Similar studies, including the measurement of elongation and hardness, have been performed by Gann and Winston,4 Dumas and Rockaert,5 Haughton and Prytherch,6 and by Spitaler, the last being reported by Beck.7 A slight superiority in the tensile strength of chillcast Mg + 8 Zn alloy over the sand-cast alloy was noted by Maybrey 8 That alloys of magnesium containing 5 to 12 pct zinc

Jan 1, 1948

By Mohab Sabry

Pile foundations are used extensively around the world to support both inland and offshore structures, including important structures such as nuclear plants and oil drilling platforms. The limit of the pile depth is currently predicted during the pile deriving process, given no chance for the designer to predict accurately the capacity of these piles prior installation. Furthermore, after pile installation, designer may not be able to modify the pile group design by increasing the number of piles and or changing the geometry of the pile group. This paper presents a numerical model for the case of single piles driven in homogenous sand using finite element technique and the theory of cavity expansion. The model is capable of simulating all the construction stages of concrete piles up to the maximum depth, which can be driven in sand and accordingly the capacity, which can be attained by these piles. The program "PLAXIS" is used to perform the proposed analysis. This model simulates the process of pile driving in terms of the changes in the earth pressure and the overconsolidation ratio acting along the pile's shaft. Based on the results of the present investigation, these depths can be predicted based on the pile geometry and the sand properties. Charts are given to provide these depths for given pile/soil conditions.

Jan 1, 2006

By L. E. Krys, K. D. Harrison, C. G. Anderson

Since 1984, nitrogen-species catalyzed pressure leaching has been utilized at Sunshine Mining and Refining Company for the recovery of precious metals from a refractory sulfide concentrate. The process operates without the use of cyanide. The plant is now the only industrial-scale commercial application of this technology. Since the inception of the process, changes have been implemented to improve efficiencies and throughputs. Two of these changes, the replacement of nitric acid by sodium nitrite and a concentrate regrind, have recently been implemented. This paper discusses the development and potential mechanisms involved in these recently patented plant-process changes. A companion publication (Anderson et al., 1996) covers the plant integration and potential applicability of the technology.

Jan 1, 1997

A minimum target of economic growth in Australia has been set at 5% per annum growth in G.N.P. at constant prices (Vernon Committee). 2. The core of the problem of sustaining steady growth at this or a similar rate is to ensure regular flows of investment. This sustains productivity, helps to control balance of payments pressures, and to check inflation. 3. The regular intake of human and physical resources, in conjunction with intensive capital development involving finance, technology and management, is basic to sustaining the growth rate and ensuring rising standards of living.

Jan 1, 1971

A roof rating system has been devel¬oped for upper seam damage prediction during mul¬ti-seam mining based on structural and geologic conditions in the upper seam. Two primary consid¬erations -geologic and spatial - form the basis of the classification system. It includes factors commonly found in geomechanics classification systems as well as factors which are peculiar to multi-seam mining, such as those which define the two adjacent seams and the innerburden. This rating system has been applied to numerous case studies to form empirical relationships for quan-titatively predicting potential upper seam damage based on anticipated subsidence and strain values and vertical movements.

Jan 1, 1988

By Nancy Estrada, Jane Nowell, Cathy Jennings, Debra Yniguez, Carol Lavery, Kristin Harrer

Pilots of the MH-60S helicopter are exposed to continuous whole body vibration (WBV). Pilot fatigue is a growing operational concern due to the increased frequency of extended durations of missions (6-8+hours) in support of Operations Iraqi Freedom and Enduring Freedom. Endurance aspects of the currently used rotary wing seating systems were not optimized for the longer missions and wide range of pilot anthropometric measurements, which is now typical of naval aviation. The current seating systems were designed primarily to meet crashworthiness requirements, not for the wide range of pilot anthropometry or to mitigate WBV. Albeit, an issue, pilot fatigue and reduced mission effectiveness are also critical concerns. Current Hazard Reports indicated that pain in pilots’ legs and backs begin two to four hours into the flight and increase with time. Mission readiness also decreases with an increase in flight duration due to the constant distraction of pilots shifting in their seats while trying to get comfortable. Froom, et al [2] reported a dose-response relationship between the length of military helicopter flights and back discomfort. He also concluded that this pain is typically dull, over the lower back, and its prevalence and intensity are dependent on the total flight hours of exposure. Methods This study evaluated WBV produced in the pilot seating systems onboard the MH-60S. The purpose of the study was to test and compare the effectiveness of two different seat cushions, the current seat cushion versus an anti-vibration seat cushion. Both seat cushions were measured for acceleration levels averaged over five-minute intervals using a triaxial seat pad accelerometer. The recordings were completed for a 3-hour straight and level flight. A frequency analysis from 0-80 hertz (Hz) was conducted on all acceleration measurements to determine the dominant axis and frequency of the pilots’ vibration exposure. The results were then compared to the applicable Threshold Limit Values (TLVs) established by the American Conference of Governmental Industrial Hygienists (ACGIH) [1] and the International Organization for Standardization (ISO) 2631.1 [3] to determine the MH-60S pilots’ permissible exposure time for both seat cushions. Results The results of the study showed that for both seat cushions the vibration levels of the z-axis at 16 Hz had the shortest allowable exposure duration, according to the ACGIH TLVs. In the z-axis at 16 Hz, the MH-60S’s current seat cushion’s acceleration levels indicated an exposure time limit of approximately 6 hours, while the anti-vibration seat cushion’s acceleration levels pierced the 8-hour exposure time limit curve. This is shown in the graph below.

Jan 6, 2006

By M. Soderstrom

In a solvent extraction (SX) plant, stage efficiency calculations are used to determine mixer efficiency. With modern extractants and mixing equipment, it is generally taken for granted that stage efficiencies will be above 95%, but this is not always the case. Dependant on mixer/solution conditions, stage efficiencies can occasionally be low, therefore leading to higher reagent usage. Proper methods to identify when stage efficiency performance is below expectations, and ways to identify if it is an equipment or chemical issue are valuable tools for a plant metallurgist. With these tools and skills an on-site metallurgist can more quickly return their SX plant to proper operation. This paper will discuss methods for analyzing stage efficiency, evaluating factors that may affect stage efficiency, and evaluating the impact of stage efficiency on the overall operation.

Jan 1, 2010

By S. Srinivasan

Traditional pit optimization techniques cannot take account of the requirement to blend ore in order to produce a saleable product, as is the case for iron ore, coal, limestone and other industrial minerals. Various techniques are proposed to overcome the deficiencies, many of which have been tested. The techniques in general involve the combined application of pit optimization and blend optimization techniques.

Jan 1, 1996

By R. H. Jacoby, M. J. Rzasa

Experimental equilibrium vaporization ratios were obtained for nitrogen, methane, carbon dioxide, ethane, and hydrogen sulfide in natural gas-condensate systems. Two different overall mixture compositions were investigated over the pressure range 500 to 4,000 psia at 100°, 150°, and 200 °F. Partial phase diagrams of the mixtures were obtained; one of these showed a critical point at 204°F and 3,875 psia. These and earlier data' were compared with the Kellogg correlation' at! 100°F and 1,000 psia. INTRODUCTION The authors' have presented equilibrium vaporization ratios for nitrogen, methane, carbon dioxide, ethane, and hydrogen sulfide in complex mixtures, such as natural gas-crude oil and natural gas-absorber oil. Since mixtures of the natural gas-condensate type also occur widely in petroleum reservoirs and often contain the non-hydrocarbons mentioned, it would be useful to have appropriate K data for calculating equilibrium vaporization conditions. Roland, Smith, and Kave-ler' obtained K's for methane and the light hydrocarbons in gas-condensate mixtures; and Poettmann and Katz3 obtained K's for carbon dioxide in a gas-condensate system. The data presented in this paper extend this coverage to include K's for nitrogen and hydrogen sulfide and phase diagrams for the experimental mixtures. EXPERIMENTAL WORK The equipment and experimental procedure was essentially as described previously, except for analysis of the vapor samples. The vapor sample bombs were filled at the pressure and temperature of the run. Immediately after sampling, a portion of this sample was flushed from the bomb into a 650 cc glass bulb, filling it to near atmospheric pressure. The sample in the glass bulb was then analyzed by the mass spectrometer. Some checks were made on this analytical procedure to find the accuracy of measurement of the C + content of the vapor samples. The modifications tried were complete fractionation of the vapor sample and the use of several liquids (depropanized condensate and retrograde liquid from several vapor samples) as calibrating materials for the mass spectrometer. The results obtained from these various checks differed by about 10 per cent relative and this is believed to be the order of accuracy of the vapor C+ concentrations.

Jan 1, 1953