Search Documents

By I. Iwasaki

The interaction of starch and calcium ions in soap flotation of activated silica from iron ores was investigated using the response surface method. The results were correlated with adsorption studies and into pilot plant tests. It was reported previously1,2 that in soap flotation of activated silica from iron ores there existed an optimum combination of the amounts of starch and calcium chloride addition, and that corn starch as a depressant for iron oxides became effective when a critical amount of starch was added, beyond which excess starch appeared in measurable quantities in the aqueous phase. Further, adsorption studies2,3 with various starch products on hematite or quartz showed that the adsorption of starch at a given pH was markedly enhanced by the presence of calcium ion in solution. From these observations it becomes of interest to investigate the interaction of starch and calcium added to the ore pulp, and their influence on the selectivity of flotation separations. This paper describes an empirical relation between such dependent variables as the grade and recovery of iron in the concentrate and the residual concentrations of starch and calcium ion in solution as a function of two independent variables, namely the amounts of starch and calcium chloride addition, as determined by using the general technique of response surface methodology. The results thus obtained are correlated with the adsorption studies on hematite and quartz, and with a typical pilot plant operation. MATERIALS AND METHODS The ore sample used in the batch flotation studies was the fine fraction of a Mesabi gravity concentrate produced by pilot plant grinding and classification. The sample analyzed 55.21% iron and 14.70% insol, and consisted of 85.81% minus 325 mesh (corresponding to Ore C). 2

Jan 1, 1965

By M. J. Coolbaugh

There is a need for concepts and techniques developed specifically for blasting in areas where the rock is loose or highly fractured. Common practice has been to use techniques developed in hard homogeneous rock and reduce the amount and strength of explosive. However, this rule cannot cope with all of the special characteristics of highly fractured rock and has not adequately taken care of the problems of overbreak, gouging, and wall damage. The main problems encountered when blasting in highly fractured rock are controlling the amount of rock broken, minimizing the damage done to the remaining wall material, and adapting blasting methods to rapidly fluctuating ground conditions. In addition, because it frequently needs timber support right into the blasting area, there is also the problem of how not to shoot out the timber when heavy loading is needed in order to offset a loss of impact caused by deflection of the detonation wave off the numerous rock interfaces, and by the absorption of the wave by resilient clay particles. Another consideration is the fact that less attention needs to be directed toward producing satisfactory fragmentation of the broken rock. Those blasting methods designed for breaking hard rock into manageable segments are, as a rule, not needed in highly fractured rock which will usually break along its own numerous fracture lines.

Jan 8, 1965

By T J. Howard

At BHP Billiton Iron Ore operations, run of mine ore from the several Newman Joint Venture (NJV) mines is railed in 12 kt rakes to Port Hedland. Rakes are processed sequentially, with the lump and fines components from each rake sampled after crushing and screening. The grade of ore from the individual mines varies around consistently different means. Although a discrete sample is attributed to each rake, the sample contains some material from the following and/or the preceding rakes due to dilution by ore from the neighbouring rakes during the dumping, screening and crushing processes. Individual rake grades at the port are therefore biased according to the mine sources of adjacently processed rakes. Dilution does not affect the grade of the overall NJV product or the accuracy of port stockpile grades; however, it does limit the ability to use port rake grades to review the quality performance of individual mines and provide meaningful lump-fines algorithms and port to mine biases for individual mines, information that is useful when scheduling ore for mining. A non-linear regression model has been used to estimate the average dilution from the preceding and following rakes. It has been shown that the lump and fines samples for 12 kt rakes are each diluted within the Port process with about 8.3 per cent of the sample coming from the preceding rake and about 3.6 per cent from the following rake. This can bias the reported rake grade by up to one per cent iron. The results of this analysis have been incorporated into the daily grade scheduling system to provide more accurate individual mine grade data and consequently better decision making.

Jan 1, 2007

By W. A. Hockings, G. W. Lower, K. A. Smith

The kinetics of dissolution of metallic copper in aqueous cupric ammonium carbonate solutions were investigated. The major variables studied were temperature, agitation, and the cupric, cuprous, ammonia and carbonate concentrations. The rates of copper dissolution from rotating discs were determined by measuring the weight loss. The dissolution rate increased with the square root of the disc rpm and doubled when the temperature was increased from 20°c to 40°C.

Jan 1, 1973

For the benefit of those of our members who are considerable holders of securities, but owing to their isolated situations are not in close touch with the metropolitan market and current quotations, we are publishing PRICE TREND OF NEW YORK BOND MARKET This graph shows the average prices often railroad, ten industrial and five public utility bonds on the first business day of each month from January, 1915, to December, 1918, and the weekly fluctuations since January 1, 1919. two very interesting graphs, showing the course of the bond and stock markets in New York over a long period. These graphs are furnished through the courtesy of the financial department of the New York Tribune.

Jan 4, 1919

At its meeting on February 21, 1933, the Board of Directors the following resolution defining and expressing the policy of the Institute with respect to official participation or action in controversial matters: WHEREAS, the Board of Directors at its last meting passed the following resolution: "The Board of Directors, having been appealed to by several Local Sections for advice concerning the attitude and policy of the Institute relating to the endorsement of candidates for public office, the following statement of policy is formulated:

Jan 1, 1939

Exploring for deep shallow dipping orebodies can be very expensive and very difficult. Surface exploration is often not an option and obtaining the best location for underground drilling can cause production delays if drilling is carried out from development headings. The Otter/Juan mine has been in production for approximately 34 years. All of the production is now sourced from more than 1000 metres below the surface from an area known as the Edwards Lode. The orebody is shallow dipping and open at depth. Exploration drilling has been performed from decline stockpiles and from hangingwall drill drives. Drilling from footwall positions (eg decline stockpiles) into shallow dipping orebodies can often produce intersections which are unusually thick thus leading to optimistic resource figures. The decision to develop a dedicated hangingwall drilling position can vastly improve the quality of the data used to generate an orebody model. In 1997 a new extension to the Edwards Lode was discovered and named the æFÆ surface. In 1999 a resource calculation was performed using data obtained from drilling that was carried out from decline stockpiles. In 2002 a dedicated drill drive was developed into the hangingwall of the æFÆ surface to obtain better data to verify the previous resource calculation. For this case study obtaining more representative data reduced the resource estimate by 66 per cent. This information was obtained early enough to allow for alteration to the mine plan and without loss of capital.

Jan 1, 2003

By Andrew J. Fergus

A study of the flotation characteristics of columbium-tantalum minerals was made by contact-angle and microflotation methods, and the findings were confirmed by flotation of two natural ores. In the contact-angle study conditions for collection of columbite, pyrochlore, and tantalite were determined for (1) sodium oleate with a sulfonate; (2) sodium isooctyl phosphate; (3) a short-chain primary amine; (4) a long-chain primary amine; and (5) a quaternary amine. These conditions were confirmed in microflotation tests. Information about collector action on common gangue minerals was also obtained by these two methods. In batch flotation tests on a pyrochlore ore and a columbite ore, it was demonstrated that collectors selected on the basis of contact-angle and micro-flotation studies would float columbium minerals from a complex natural ore. However, multiple cleaner and scavenger flotation steps will be necessary to produce commercial concentrates. From a pyrochlore ore containing 0.54 percent Cb2O5, a 44.4 percent Cb2O5 concentrate was made containing 36.4 percent of the total Cb2O5. For a columbite are the corresponding values were: 4.35, 54.6, and 67.1 percent. During the batch flotation study, wetting agents were found to aid in the gangue-ore mineral separations.

Jan 1, 1968

By A. C. Fieldner, F. H. Gibson, W. A. Selvig

A foRmer paper1 described in detail various methods of calculating coal analyses to obtain the composition and calorific value of the pure coal substance—that is, of the coal free from its mineral matter. The paper included a table showing calorific values of pure coal, as calculated from float-and-sink portions, by means of the Parr formula for "unit coal" and by the customary moisture-free and ash-free formula. A modification of the Parr formula was proposed, based on the assumption that one-half the sulfur present in Coal occurs as pyritic sulfur and one-half as organic sulfur. In the published discussion of the paper Cady gave a table of results on a large number of Illinois coals as obtained by the Parr formula and the proposed modification thereof. The results obtained by Cady indicate that the Parr formula applies better to Illinois coals than does the modified formula proposed by Fieldner and Selvig. The present paper gives results obtained by applying the modified Parr formula to the analyses of the float-and-sink portions of the coals shown in the former paper, and results obtained by applying the Parr formula, the modified Parr formula, and the simple moisture-free and ash-free formula to various coals of the United States ranging in sulfur content from less than 1 per cent to more than 4 per cent sulfur. A graphic method of estimating the calorific value of pure coal and determining the relation of the coal ash to the mineral matter of coal, as proposed by Stansfield and Sutherland,2 was applied to a number of coals, and the results are given herein. Testing Formulas with Float-and-sink Separations The former paper by Fieldner and Selvig gave heat values of pure coal of the float-and-sink portions of 21 coals, as calculated by the Parr formula

Jan 1, 1932

By W. Biermann

All industrial processes are economically driven, resulting in the ever increasing need for process optimization in order to stay competitive and profitable. Numerous models has been published depicting the optimization of the raw material usage in an arc furnace, as well as the thermal and electrical efficiency; however, to obtain a holistic view of the cost-effectiveness of the process one needs to expand the model to include the cost of all the operational variables. This project therefore aimed to not only include the raw material feeds and power consumption as input variables, but also the labour, maintenance, and environmental costs to generate an all-inclusive financial balance. In the end, the model was able to mathematically optimize the ferrochrome (FeCr) production process through evaluating the effect of a specified combination of input parameters. It could therefore be used as a tool to aid in managerial decision-making; to appraise and correspondingly adjust certain operational variables in order to achieve a maximum return on investment. This paper fully describes the reasoning behind the choice of the essential model components, the assumptions made during the models development, the calculation approach, as well as the advantages, limitations, possible applications, and areas for expansion of the final model. Through running simulations with plant data, it was found that the accuracy of final model remained fairly constant when applied to stable furnace conditions, but was met with a number of limitations when applied to more complex situations. These limitations could, however, be overcome through further development and expansion of the existing model to include a larger number of process variables.

Jan 1, 2012

Environmental and amenity factors have introduced a new dimension to the technical problems of the mining industry in finding, extracting and processing the mineral and energy products on which we all depend. Intervention by outside regulatory bodies is restricting the production of minerals and denying the industry access to large areas in which the orebodies of the future may occur. The solution lies to a large extent within the industry itself and appropriate management techniques are necessary to ensure that exploration and mining are seen as an acceptable as well as a necessary land use. Close liaison between operators and the responsible authority is necessary to achieve these objectives and to make the best use of our land resources.

Jan 1, 1979

By Shaoxian Song, Ling Xia, Hongqiang Li, Yubiao Li, Yunliang Zhao, Shaobing Xie

Since human daily demands for fresh water have been increased significantly, the supply of fresh water for the mining industry, especially froth flotation, should be considerably reduced. In addition, stricter environmental standards have been implemented in many countries to reduce the risks due to the disposal of wastewater, many flotation operators have to seek more efficient ways to utilize the limited fresh water sources. Recycling water with high concentrations of impurities is a normal strategy for most of the mineral processing plants; however, water quality should be carefully considered to guarantee a smooth flotation process. Recently, the application of seawater in flotation has attracted much attention due to its availability and abundance rather than fresh water. However, the influencing mechanisms due to the application of seawater in flotation have not been fully understood especially the reactions between mineral particles and bubbles in the presence of high concentrations of cations and anions. This would impede the application of alternatives to fresh water in the flotation. Therefore, this paper reviews the current water sources and the technologies for water recycling in the flotation process. Specifically, the life cycle of water in flotation was proposed. In addition, the strategies including high pulp density flotation as well as the most promising alternatives to fresh water have been discussed in details, with the related mechanisms being demonstrated.

By Margaret E. Egan

Reliable fire detection is essential for both safe evacuation and containment or extinguishment. In order to increase reliability by reducing the number of nuisance fire alarms in underground mines that use diesel-powered equipment, the U.S. Bureau of Mines has developed a diesel-discriminating fire detector (DDD). It was designed to discriminate between smoke produced by a fire and the smoke-laden exhaust of a diesel engine. Experiments were conducted by the Bureau to compare the smoke detection capabilities of the DDD with those of conventional fire detectors in response to smoldering coal and conveyor belting. A comparison was made among the alarm times of a carbon monoxide (CO) detector with an alarm threshold of 5 ppm, a smoke detector with an optical density alarm threshold of 0.044 of', and the DDD with an alarm threshold of 0.025 V. The results show that the DDD will reliably detect developing coal and conveyor belt fires. The average time delay separating the DDD alarm from the first detector to alarm was 76 s for smoldering conveyor belt and 65 s for smoldering coal. The longest time delay between the response of the DDD and the first detector to alarm was approximately 120 s.

Jan 1, 1993

By A Valero, G M. Mudd

There is active debate and research around the most suitable indicators to assess the sustainability of mining. The most common approach is to report a range of data for a given mine site (or less preferably, a company total), such as inputs, outputs, benefits and potential costs. The most popular protocol in use (and growing rapidly) is the Global Reporting Initiative (GRI). However, these measures are numerous and still do not allow a single over-arching indicator to be developed. Other measures, such as known mineral resources over time, do not account for critical challenges such as declining ore grades, increasing wastes and poorer quality ores or more difficult mineralogy. By adopting a thermodynamic approach to sustainability, through the concept of æexergyÆ, it is possible to incorporate into a single measure the effective quality of mineral resources. Exergy involves the assessment of the minimum energy costs involved in producing a mineral resource with a specific chemical composition and concentration from common materials in the environment. The exergy of a mineral resource is evaluated from mineralogic composition, concentration (or ore grade) and, of course, quantity, by multiplying the unit exergies with the tonnes of the resource produced (or consumed). Since exergy is a thermodynamic quantity (ie energy or joules), it is additive across different minerals, such as iron ore to gold to copper or even oil and gas or coal û making it an ideal indicator to assess mineral resource sustainability at the industry scale rather than the individual mine scale. This paper briefly outlines the theoretical basis for exergy, and then presents a range of commodity case studies showing the application of exergy to the Australian mining industry. Overall, the usefulness of exergy is clearly demonstrated for use as a broad indicator of the sustainability of mineral resources at the national or even global scale.

Jan 1, 2009

By L. R. C. Cairncross

In this study, the general case of semi-batch precipitation of nickel hydroxide, Ni(OH)2, is modelled. In practical terms, this precipitation may occur at high ionic strengths, and therefore the model for solution chemistry requires a thermodynamic model that is applicable for these non-ideal systems. The activity coefficient model used is the ELEC-NRTL. The simulation of the solution chemistry is performed using AspenPlusTM, which is a steady-state process simulation program. This allows for rigorous evaluation of the solution speciation, and hence the degree of supersaturation which dictates the precipitation kinetics. The solution chemistry provides the basis for predicting the formation of solids. The model consists of a solution chemistry part and a solids formation part. The inputs to the model include the initial concentrations of the streams entering the reactor, kinetic parameters for the precipitation processes, and a particle size distribution obtained from experiments. The solids formation part of the model employs the method of moments for the evaluation of the population balance. The population balance accounts for total particle number, and the formation and increase in size of particles across the entire particle size range. This balance requires kinetic parameters for the processes of nucleation, growth and agglomeration. Using optimization routines inherent in AspenPlusTM, parameters for the rate of nucleation, growth and agglomeration may be extracted from experimental particle size distributions. These are then used in the model to extrapolate to other conditions. Once an understanding of the kinetics of the precipitation processes is gained, the model provides a predictive tool for optimization of these kinetics, in order to increase the overall particle size and therefore improve solid-liquid separation. The work is deemed to be significant as it sheds some light on solids formation processes involved in precipitation?including nucleation, growth and aggregation?and develops a predictive modelling tool applicable to solutions of high ionic strength. We argue that this dewatering of suspensions is affected significantly by particle size distribution and surface properties of the solids formed by precipitation. This modelling tool should facilitate the design of solids formation processes where downstream dewatering is enhanced.

Jan 1, 1997

By R. S. Shepard

The closing remarks of a paper which I presented at the annual AIME meeting at Dallas, Texas during February of 1963; contained a forecast of increased activity in trackless underground ore mining which finalized that presentation. At that time, HAD I been peering through my brightest rose colored glasses, I could not have foreseen the unprecedented rapidity of acceleration of underground ore mining methods which has since ensued. From Death Valley, California diagonally to St. Johns, New Foundland; from Australia to Africa to Sweden to France and Germany; from South America to Southern Mexico to Northern Saskatchewan and Northern Manitoba the expansion of trackless underground ore mining methods has probably progressed at a faster rate than any other revolutionary' change in the history of underground ore mining.

Jan 1, 1967

At many locations in Australia the decommissioning of mining operations will require the disposal of excess water. If the water is contaminated its disposal may be restricted by government guidelines. The timing of water disposal may be critical to the schedule of close-out. The uncertainty of the annual rainfall input to the water storage and disposal system may determine the success or failure of close-out. The uncertainty associated with any outcome can be used to determine the reliability of the system, or inversely its risk. The technique of Monte Carlo simulation, using the uncertainty in annual rainfall, is applied to quantify the risks associated with water disposal as part of the requirements for close-out in two case studies. In both case studies it is assumed that water disposal is via evaporation only. The first case study is the Nabarlek operation, located about 270 km east of Darwin. This project is required to complete the engineering work associated with its close-out by December 1995. The second study investigates the situation of close-out for the Ranger Uranium Mine, about 250 km east of Darwin. It should be noted that the Ranger mine was examined as part of the annual update of its contingency rehabilitation plan and the probability of implementing the plan is extremely small. The probability of success for the Nabarlek case varied from less than ten per cent to greater than 95 per cent depending on the management strategy. Four possible strategies were investigated for the Ranger mine with the chance of success varying between 20 and 95 per cent. The estimation of the evaporation rate and the area allocated to evaporation was critical in both cases. By applying seasonally based evaporation pan coefficients determined on site, rather than an average monthly value of 0.75, the chance of success was improved by up to 35 per cent for Ranger. Simulation modelling is able to provide information on the likely response of mine water management systems and the level of risk. This information is required to efficiently plan and manage the disposal of water for close-out.

Jan 1, 1994

By D. J. Robertson

"THE copper smelting operation of the Hudson Bay Mining and Smelting Company, Limited, at Flin Flon, Manitoba, generates a gas flow of 350,000 c.f.m. at n.t.p. This gas stream passes to atmosphere through a 20-foot diameter by 250-foot brick stack, carrying with it an appreciable dust burden in the form of metallic oxide fumes. The flow constituents during the period 1952 and 1953 and •before gas filtration was included in the treatment scheme are shown in Table I. This paper describes the gas filtration treatment which was installed in 1957, using glass cloth media to recover this dust burden, and discusses the associated problem as its treatment for recovery of zinc and cadmium.The metallurgical details associated with the problem are illustrated by a description of the material flow sequence of the Company's hydrometallurgical zinc plant and copper smelter. In this ore processing complex, the zinc plant and copper smelter form an integrated unit within which intermediate zincrich products of each operation enter the treatment circuit of the other."

Jan 1, 1960

By D. I. Verrelli

Within the flotation community a belief has developed that some particle shapes are more ?floatable? than others. This is usually attributed to an influence of particle shape or roughness on the induction period required to achieve attachment between the particles and the air bubbles in the pulp. Up to now, such measurements have not been able to readily isolate the effect on individual flotation subprocesses. In contrast, our experimental apparatus, the CSIRO Milli-Timer, enables us to directly observe the process of particle?bubble interaction and attachment by means of a high-speed video recording, thus providing a direct measure of the induction period for attachment. To assess the influence of particle shape on induction time we used two varieties of methylated borosilicate glass particles ? spheres and angular ?frit? ? in a range of tightly-sized fractions. In doing this, we take care to account for the influence of other factors that could affect the induction time, such as the polar angle of sliding commencement, and approach velocity. These parameters are recorded as variables for each interaction, and corrected for using multiple nonlinear regression. Our results illustrate the importance of particle shape on induction period, with angular particles exhibiting induction periods that were an order of magnitude lower than those of spheres. Furthermore, the induction period was seen to decrease with increasing particle velocity, or kinetic energy on approach, but increased as the trajectory approached the limit of just grazing the bubble. Particle shape in mineral processing is a consequence chiefly of the mineral type and the type of grinding employed. The results presented herein indicate that attention should be paid to the shape of particles obtained from the grinding operation, besides particle size. Keywords: attachment, bubbles, flotation, induction period, particles, shape effects, surface roughness

Sep 1, 2012

By Fred D. Wright

This paper describes research at the Bureau of Mines experimental oil-shale mine at Rifle, Colo., to improve blasting techniques and reduce breaking costs. Many of the conclusions are applicable to any mining operation. Experiments Were conducted on many phases of blasting. The effectiveness of various grades of explosives was compared, and several different drill-hole patterns were tried in heading rounds. An experiment was conducted to determine the maximum effective burden for various diameter blast holes. High-speed motion-picture studies were made of blasts, and the time for initial movement of rock after detonation of the explosive was measured. Experiments with millisecond-delay detonators in heading rounds proved that, when used properly, these detonators result in improved fragmentation, economical use of explosive, and compact, easily loaded muck piles.

Jan 1, 1953