Search Documents

By T. Federighi, S. Ceresara, C. Panseri

The results of an exploratory investigation by means of resistivity measurements at -195ºC, on the aging characteristics of a set of Al-Mg alloys with a maximum content of 7 pct Mg, are reported. Whereas for dilute alloys (Mg < 1.5 pct) only a decrease in resistivity is observed at about 100°C (due to the elimination of quenched-in vacancies), for more concentrated alloys such a decrease is preceded by an increase in resistivity in the range between -60ºand +40°C. Following some previous suggestions, this increase is considered as good evidence for clustering of solute atoms @reprecipi-tation process). From the analysis of the results it appears that, although the process is substantially similar to that observed in other Al-rich alloys, it is characterized by a strong interaction between vacancies and zones. THE process of formation of Guinier-Preston zones, i.e., preprecipitation,1&apos;2 which occurs during the aging at about room temperature in many supersaturated aluminum-rich alloys, has been extensively investigated in the past few years by several workers.2,3 owever, a very interesting question arises when the case of Al-Mg alloys is considered: although it is very easy to supersaturate Al-Mg alloys, just in the same way as for many other aluminum alloys showing preprecipitation, only very little experimental evidence was available until a short time ago in the literature supporting the existence of "natural" aging in supersaturated Al-Mg alloys (see, for example, Refs. 4 to 6). On the other hand, as is well known, the X-ray method is not useful in this case because the X-ray scattering factors of magnesium and aluminum atoms are about the same. Recently, however, Cordier and Detert7 have stressed that during the aging at about room temperature of a supersaturated Al-Mg 10 pct alloy it is possible to detect an increase in resistivity; since, as is well known, such an increase is observed also in most alloys showing preprecipitation, the above authors have interpreted their results as evidence for the formation of magnesium-rich clusters (or Guinier-Preston zones) during the aging. In the course of or ientative investigations on preprecipitation in several aluminum-rich alloys, we also could detect a similar phenomenon in more dilute Al-Mg alloys, see Instituto Sperimentale Metalli Leggeri, Annual Report, 1959, and also Ref. 8. Since the details of our observations, although of a preliminary nature, differ from those of Cordier and Detert and allow one to draw a more advanced picture of the preprecipitation process in Al-Mg alloys, we have thought it useful to report our results in this paper and to comment on them briefly.

Jan 1, 1963

By Robert H. Merrill, David W. Wisecarver, Raymond M. Stateham

The US. Bureau of Mines, in cooperation with US. Borax and Chemical Corp. and Kennecott Copper Corp., has investigated the use of the microseismic method to evaluate the stability of large, open-pit slope walls. The method is based on the phenomenon that stressed rock normally emits subaudible rock noises, and the number of rock noises per unit time (noise rate) and the magnitude of the rock noises (amplitude) increase as the stresses in the rock approach the failure stress of the rock. Therefore, the detection and recording of those rock noises serve as a semiquantitative method of predicting the incipient failure of rock. This report briefly describes the three different types of micro-seismic apparatus, the procedures, and the results of microseismic investigations in the slope walls of the Boron mine near Boron, CaL, and the Kimbley, Liberty, and Tripp-Veteran open-pit mines near Ely, Nev. Microseismic monitoring within a frequency band of SO to 5000 Hz indicates noise rates in stable, inactive mining areas are between 0 and 10 noises per hour; the rates in stable, active mining areas are between 10 and 50 noises per hour; and the rate in unstable areas is as high as 2500 noises per hour. High microseismic noise rates in the Liberty pit correlate with the time of nearby earthquakes, indicating that the earthquakes affected the slope wall. The results provide evidence that the microseismic technique is applicable to large pit walls, and that the wide-band, wide-range microseismic equipment appears to be suitable for open-pit investigations. The microseismic method is based on the phenomenon that stressed rock normally emits subaudible rock noises, and the number of rock noises per unit time (noise rate) and the magnitude of the rock noises (amplitude) increase as the stresses in the rock approach the failure stress of the rock. Therefore, the detection and recording of those rock noises serve as a semiquantitative method of predicting the incipient failure of rock. The method has been used for many years to detect incipient failure in roofs or pillars in underground mines. In 1963 the U.S. Bureau of Mines (USBM) started an investigation of the microseismic method in large, open-pit slope walls. The purpose of this investigation was to evaluate the method in open-pit slopes where the rock may be fractured and broken and where the size of the rock mass under investigation is much larger than normally encountered underground. In addition, both the stresses in the rock and the strength of rock near pits are lower than usually found underground. Consequently, there was some doubt concerning the feasibility of the method for open pits, and the economics of such an investigation may have been prohibitive especially if large walls had to be monitored with closely spaced geophones. The successful application of the microseismic method to underground operations has improved safety at little, or no sacrifice, to production or extraction ratios. The anticipated reward in open-pit mining would be the improvement of safety with a minimum sacrifice to mining operations. There is also a possibility that the method could be used to optimize the unloading (stripping) of potential failure areas by the removal of intact rock from the slope wall rather than the cleanup of a slide from the bottom of the pit. This report contains a brief description of three types of microseismic apparatus used in four different pit walls, each of which is different in height, slope, rock types, or has different planes of weaknesses, such as faults, fractures, or joints. Because the geologic features of the pit walls are varied and complex, for brevity, this report dwells mostly on the microseismic apparatus, techniques, the rock noise rates, and the slope movements measured at the various sites. PROGRESS AND DEVELOPMENT The microseismic method was developed over 20 years ago; and the method and examples of investigations in underground mines are summarized by Obert and Duvall. 1 In more recent years, the method has been applied in several underground mines, and an in-situ test under controlled stress conditions is described by Morgan and Merrill. 2 Experience has shown that, on occasions, the microseismic noise rate and amplitude reach a peak value and then start to decrease before a failure occurs in an underground mine; on other occasions, the noise rate steadily increases to a maximum at failure. The method has been applied to slopes by Goodman and Blake,3 and by Paulsen. 4 Goodman and Blake found that the noises corresponded with failures in the slope

Jan 1, 1970

By Jeffrey Johnson

To measure the loading behavior of friction bolts, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) installed strain gauges on the interior of friction bolts and developed a battery-powered miniature data acquisition system (MIDAS) that fits inside the hollow portion of the friction bolt. The advantages of this system are that it is protected from face blasts and eliminates the need for external wiring. Laboratory pull-out tests showed that friction bolts installed in a concrete block with resin were loaded to about 1.8 tons/ft of bolt length; bolts installed without resin were loaded to 1.3 tons/ft. Three strain-gauged friction bolts were installed at Hecla Mining Company&apos;s Gold Hunter Mine, Mullan, ID, in the wall or rib of a mechanized cut-and-fill stope. The object of these tests was to establish an installation procedure for the bolt-and¬MIDAS combination and to evaluate performance. The stope was advanced in three 15-ft increments and strains induced in the rock bolts by stress changes in the rock were recorded every 30 minutes. The MIDAS proved to be rugged enough to withstand the shock and vibration from nearby (5 ft) face blasting. Data from MIDAS showed that the friction bolt installed with resin was the most sensitive to each face advance. It showed a steady increase in loading to a maximum value of 1000 microstrain. The friction bolt installed without resin showed stick-slip behavior with loads to a maximum of 400 microstrain before the stope was completed.

Jan 1, 2003

By Thomas R. Smith

This paper covers oil shale resources in those countries that border the Pacific Rim. The major known resources around the Pacific Rim occur in the Western United States, Australia, the People&apos;s Republic of China, (PRC) and the Thailand/Burma region. The location of these deposits is shown in Figure 1. In 1965, the U.S. Geological Survey estimated world oil shale deposits of over 4 quadrillion tons having a potential oil yield of over 2 quadrillion barrels. If all this were extracted, it could meet the world&apos;s entire energy needs far into the future. However, the Survey also estimated the spent shale waste could cover all of the surface of the world to a depth of about 10 feet. Thus, for this and many other technical and economic reasons, it does not appear to be feasible to develop a large portion of the world&apos;s oil shale resources in this century; nor will shale in itself solve our energy problems. Nevertheless, shale oil and other &apos; synthetic fuels are expected to play an important role in new energy supplies in the longer term. WHAT IS OIL SHALE OR SHALE OIL? The term "oil shale" is sometimes a misnomer, in that the rock is often more of a limestone or siltstone than a shale. The common link between resources termed “oil shale" is that they all contain an insoluble substance cal led kerogen (which is from the Greek words for waxmaking). Kerogen is a form of organic carbon derived from a variety of plants ranging from algae to higher plants. When heated sufficiently, the kerogen generates hydrocarbons called shale oil, a form of synthetic crude oil that in most cases is lower in hydrogen content than conventional crude oil. The amount of oil in oil shale is relatively small --roughly 10 percent (by weight) in the richer shales. To upgrade this synthetic oil to usable products, additional processing is necessary. This brief sketch gives an idea of what this different, but significant, form of hydrocarbon is like. ENVIRONMENTS OF DEPOSITION Most oil shale deposits fall into three environments of sediment deposition: 1ake (called lacustrine), sea (marine) and river (fluvial-deltaic). In each case, the deposition of oil shales took place in quiet water environments where plant life, particularly algal plants, could flourish and, after dying, be deposited in unoxygenated water where the kerogen precursors would be safe from destruction by oxidation. The oil shales that were deposited in large lake basins (lacustrine) have attracted the most attention for development over the years. They often have multiple seams, deposited in a cyclic nature with extensive areal distribution and rapid vertical changes in kerogen content. Grades are moderate to high, ranging from 80 to 200 liters per tonne. Rundle in Australia and the Piceance Creek Basin in Colorado are examples of this type. Both deposits represent large volumes of oil shale in small areas which could provide the large volume of feedstock needed for future commercial operations. The stratigraphic sections of these two deposits feature thick oil shale seams with average grades of 80 - 125 liters/tonne conducive to both open pit, and underground operations. However, the rock strength of the Rundle shale is not sufficient to - support underground mining. On the other hand, the Colorado deposits, being more carbonate in nature, are sufficiently strong to support either type of mining depending on the overburden to ore ratio. These latter types of deposits will likely provide the first target for development of a commercial industry. The marine type is characterized by extensive areal distribution with relatively thin seams. The grades are generally low to moderate, ranging from 50 to 120 liters per tonne. The marine oil shales are common worldwide, and their attractiveness for mining is dependent on the overburden to ore ratio. Because of their widespread areal distribution, their in situ resources can be quite large. The Toolebuc Formation in Central , Queensland, Australia is a good example of this type of deposit being 7-10 meters thick over an extensive area. The Julia Creek deposit with its favorable overburden-to-ore ratio is being studied for possible development. In a fluvial-deltaic environment, there are many small lakes or bogs associated with rivers in which a very pure type of oil shale called torbanite could form. Torbanites are very high grade containing up to 75 percent hydrocarbons. The known occurrences are generally small lenticular deposits associated with coal seams. Even with the high grades, it is not likely that any of the known deposits would warrant commercial development because of their small size. The torbanite deposits in New South Wales, Australia were processed prior to World War I1 near the town of Glen Davis. However, today&apos;s known resources of this type are not large enough to warrant a commercial plant.

Jan 1, 1982

By J. B. Shannon, J. D. Grenia

The Buick Mine is a joint venture of American Metals Climax, Inc. and Homestake Mining Company located 120 miles by road southwest of St. Louis, near the village of Boss, in the `New Missouri Lead Belt&apos;. Since start-up in 1969, over four million tons of lead-zinc ore have been mined and milled at Buick. Situated 1100 ft below the surface at an elevation 270 ft above sea level, the flat lying sinuous orebodies are up to 250 ft wide, 85 ft high and several thousand feet long. Mineralization is galena, sphalerite and chalcopyrite in dolomite.

Jan 7, 1973

By N Setoudeh, A Nosrati, N J. Welham

The current surge of interest in lithium (Li) is due to the anticipated demand for electric vehicles and small scale power storage. Brine deposits contain most of the global Li resource, however hard rock deposits can be more readily and rapidly developed and comprise the majority of proposed projects. These projects plan to use the conventional processing routes of dense medium separation and / or flotation to produce a spodumene concentrate for sale. The standard route for subsequent processing of spodumene concentrate is thermal decrepitation, acid leaching, solution purification and precipitation of lithium carbonate. This is typically followed by further purification. A number of projects have ores which contain other lithium minerals, principally micas, lepidolite and zinnwaldite, necessitating an alternative treatment route. Several different routes for spodumene processing are under development to reduce costs to compete with brine projects. This paper will give an overview of the strengths and weaknesses of the current and alternative processes.CITATION:Welham, N J, Nosrati, A and Setoudeh, N, 2017. Lithium ore processing – an overview of the current and new processes, in Proceedings MetPlant 2017, pp 185–194 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By Hunter W. H, Wilson I. P, Craig R. W

In September 1988 the Imperial Smelting zinc - lead blast furnace at Avonmouth England, was uprated from its then 52 week annual rated capacity of 90 000 tonnes/year of furnace zinc to 110 000 tonnes. In order to provide sufficient extra feed the sinter plant was likewise uprated in April 1989 by increasing the blowing rate of the sinter/acid plants from 100 000 to 120 000 Nm3/h, effectively a 20 per cent increase. In the 12 months after the uprate zinc production was only 85 000 tonnes. Two years after the uprate zinc production had increased to 100 000 tonnes, but it was not until January 1992 that a rolling 12-month zinc production of 110 000 tonnes was consistently achieved. This paper describes the problems encountered with the uprate and how they have been or are being overcome. It deals chronologically with events starting with the restart of the ISF at the end of 1988 and covers the following issues and their resolution: 1. Initial shortages of sinter due to an offset in uprate timing. 2. Greater difficulties in operating the larger furnace particularly on start-up, the greater tendency for iron production and serious slagging problems. 3. Coincidental timing of deleterious trends in slag chemistry. 4. Refractory problems in the furnace shaft and condenser. 5. Shortages of sinter due to commissioning problems with the wet gas and sinter tip end fans, and difficulties in obtaining sufficient sinter hardness. 6. Unrealised full benefits of the sinter-acid uprate due to a late change in design to dispense with sinter gas recirculation, but offset by successful use of oxygen. In a planned maintenance stop in September 1992 further improvements to the furnace design were carried out to resolve the refractory problems, and with improvements to the sinter plant the furnace zinc output capacity is planned to rise to a rate of 120 000 tonnes/year within two years.

Jan 1, 1993

DR FRANK DAWSON ADAMS Montreal, Canada HENRY STURGIS DRINKER Bethlehem, Pa PROF HATON DE LA GOUPILLIERE Paris, France SIR ROBERT A. HADFEILD London, England HERBERT C. HOOVER Leoben, Austria ROBERT W. HUNT Chicago, ILL JAMES FURMAN KEMP New York, N.Y. PROF HENRI LOUIS LE CHATELIER Paris France EZEQUIEL ORDONEZ Mexico City, Mexico ALEXANDRE, POURCEL Paris, France RICHARD H, RICHARDS Boston Mass. JOHN E. STEAD Middlesborugh, England PROF DIMITRY CONSTANTIN TSCHERNOFF St Petersburg, Russia CHARLES D WALCOT Washington D.C.

Jan 1, 1923

By Richard J. Mainiero

The Bureau of Mines has developed a prototype nonincendive explosive rock-breaker charge that can be fired unconfined in underground bituminous coal mines without the danger of igniting a flammable atmosphere that might be present. At present, unconfined shooting in underground coal mines is prohibited, but there are situations where the use of such shots would yield an overall improvement in safety. The charge consists of l-1/2 lb of permissible water gel explosive in the form of a short cylinder 7 inches in diameter and 7/8 inches high, surrounded by a l/2-inch-thick layer of damp salt, and encased in latex rubber reinforced with cheese cloth. The latex rubber housing provides a charge package that is strong enough to resist rough handling yet is pliable enough to conform to an irregular stone surface. A charge of this shape was found to be more effective at breaking rock than charges with lined or unlined cavities. Incendivity tests in a gallery have shown that the prototype charge will not ignite a flammable methane-air atmosphere when fired. Rock- breaking tests made with limestone boulders indicate that the charge will satisfactorily break stone slabs weighing 1 to 2 tons, and that two or more charges might be effective for slabs weighing up to 10 tons. In cooperation with the Mine Safety and Health Administration (MSHA), a test protocol for the certification of these charges as "permissible" for use in flammable atmospheres is being developed.

Apr 1, 1982

By Lee Nichols

The Oil Sand Industry in northern Alberta, Canada, disposes of the by-products of bitumen extraction into tailings ponds. The mix of tailings sand and mature fines, with gypsum added as a flocculent, constitute a waste stream called Consolidated Tailings or Composite Tails (CT). The two main challenges of the tailings disposal process are a chronic shortage of economical containment and the potential mobility of CT deposits in the event of breaching by, for example, long term erosion, which makes abandonment of tailings ponds more complicated. Thick deposits of CT do not consolidate in adequate time to provide reassurance for abandonment of the CT containment facilities and that is why the containment must be adequately robust or the properties of CT improved for long term stability. This paper addresses potential solutions to these problems by applying the gravity drainage of CT and quasi-homogeneous construction for containment facilities. Gravity drainage is suggested as a mechanism to facilitate the consolidation of CT in critical areas of the ponds by inserting internal sand layers within the body of the deposit. Critical CT areas are defined as areas around the perimeter of containment. The advantages of this solution are long-term stability of the disposal area by creation of stiff deposits around its perimeter and facilitation of reclamation efforts on its surface. The present solution for containment of CT deposits is not favourable from a materials balance point of view. In general, sand has become a valuable resource as it both forms the primary component of the CT matrix and becomes the containment building material. If sand is required for CT, less is available for dyke construction. This puts additional pressure on the industry as a whole to maximize the use of overburden and interburden for construction of tailings containment structures. Typically, only 50 percent of dry mine waste (overburden + interburden) is incorporated into dyke construction. The remainder of dry waste is stored either in waste dumps or in tailings ponds, consuming valuable in-pond space originally allocated to CT material. Quasi-homogeneous dykes are proposed to contain CT deposits rather than traditional minimum cross-section dykes built of overburden and/or cell sand. The quasi-homogeneous dyke may change the unfavourable material balance and lessen the construction constraints that are presently imposed on the mine/waste disposal process.

May 1, 2004

Jan 1, 1928

By Mark William Withey

"Blasting safety in surface mining is a necessary industrial goal. Proper techniques and disciplinesexercised during the blasting process enhance the probability of achieving that goal.The blasting process is generally a series of repetitive steps performed by all blasting technicians.Because habits formed during this process influence safety, production and cost, proper habitsbecome compulsory."

Jan 1, 1995

By Horst Konig

This paper illustrates that, with the application of new processes, smaller steel plants using local raw materials can be economical and advisable. It also introduces the problems connected with the direct reduction processes, which use non-coking coal or gas as reducing agents, and which are employed in connection with conventional reduction to produce excellent results. Electric smelting is also discussed, and some practical examples of operating plants are given.

Jan 1, 1970

By Alberto S. Nieto

The general role of geology in the location of different types of large underground chambers is discussed. Aspects of structure, rock type and state of stress are discussed at some length. Some practical implications on stability of observations about the attitude, spacing and persistence of structural features are made. Characteristics and likely problems inherent to rock types (igneous, metamorphic, and sedimentary) are discussed. Observations regarding the uniformity of stress conditions within a physiographic province are presented. The influence of stresses parallel to the chamber axis on wedge movements is briefly discussed.

Jan 1, 1983

By Nicholas J. Grant, Noboru Komatsu

Electron-micrographic studies and hardness tests were made of an internally oxidized dispersion-strengthened Cu-12 vol pct SiO2 alloy follozuing longtime annealing at elevated temperatures. The rate of coarsening of SiO2 particles and the relationship between hardness and interpavticle spacing were Dispersion -strengthened alloys exhibit a remarkable stability of structure and properties at elevated temperatures compared with conventional alloys; nevertheless, when they are exposed to high measured. The rate of coarsening of SiO2 particles is controlled by the decomposition of SiO, rather than by the diffusion rates of silicon or oxygen through the copper matrix. The mechanism of coarsening was also studied by using a diffusion-couple technique. temperatures, weakening takes place as a result of coarsening of the dispersed phase. The theoretical treatment of the coarsening of dispersed phases has been treated by Greenwood,1 wagner,, and others3 by considering the interfacial energy of dispersions and the diffusion of solute atoms. Recently, experimental work on the coarsening of relatively insoluble, finely dispersed cobalt particles in copper was reported by Livingston,4 and on aluminum oxide in nickel by Dromsky, Lenel, and Ansell;5 according to these investigations, the rate

Jan 1, 1964

By E. P. Klier, Taylor Lyman

THE structures formed when austenite is quenched to subcritical temperatures and allowed to transform isothermally have been the subject of intensive study since the work of Davenport and Bain.1 Isothermal transformation diagrams summarizing the results of many of these studies have become widely familiar to metallurgists. Of particular interest to metallographers are the dark-etching, acicular products of transformation formed by isothermal reaction below the temperature of maximum velocity of the austenite to pearlite reaction. These products, the bainite structures, can be formed in a wide variety of steels. However, the constitution of bainite is not well understood and divergent views have been expressed as to its mode of formation. In this investigation a combination of dilatometric, microscopic and X-ray methods has been brought to bear upon the problem in the hope of some elucidation of the bainite reaction as it occurs in hypoeutectoid steels. MECHANISM OF BAINITE FORMATION Davenport and Bain1 considered the mechanism of bainite formation to consist of two steps-an allotropic transformation followed by precipitation of carbide. The separation in time of the two processes was considered to be very slight in the upper temperature range and very marked at temperatures just above the martensite range. This concept has been restated by Vilella, Guellich and Bain2 in the form of a definition of the acicular mode of transformation as: The successive, abrupt formation of flat plates of supersaturated ferrite along certain crystallographic planes of the austenite grains; this supersaturated ferrite begins at once to reject carbide particles, (not lamellae), at a rate depending upon temperature. In effect, this is the acicular mode of transformation, even though the temperature be such as to limit the actual life of the quasi-martensite to millionths of a second. The investigation of isothermal decomposition of austenite in certain alloy steels (notably those containing chromium or molybdenum) has revealed that there may be a range of temperatures between the pearlite and bainite reactions in which the austenite decomposes at a relatively low rate.3-6 Further, it is characteristic that in the second region of fast reaction the decomposition of the austenite is incomplete by one reaction but goes to completion by a second reaction. These observations led Wever7 to a description of the bainite reaction as follows: I. The reaction takes place by initial precipitation of a martensitic intermediate structure. 2. In the upper temperature range this structure readily decomposes into ferrite and cementite. In the lower range carbon separates in an unknown form. 3. In the upper temperature range the precipitated carbide nucleates the precipitation

Jan 1, 1944

By B. M. Stewart

Researchers at the U.S. Bureau of Mines conducted a long-term groundwater monitoring and site characterization program at an abandoned 10-ha, acid-producing, copper-gold tailings impoundment in north-central Washington State. The purpose was to investigate contaminant release and transport, and attenuation mechanisms in the tailings, sediments below the tailings, and gravels downgradient of the impoundment. This report summarizes the monitoring results and physical properties of the tailings, the sediments below the tailings, and the groundwater system associated with the tailings. Water samples from the vadose and saturated zones of the impoundment were analyzed for 15 constituents. Concentrations of the same constituents were determined in water samples up to 3 m beneath the impoundment and in the shallow colluvium and deep bedrock at 76, 335, and 550 m downgradient and 168 m upgradient. Constituent concentrations within the tailings are quite variable and are influenced by pH, depth of oxidation, grain-size differential (surface area), hydraulic gradient, groundwater mixing, and the presence of hardpan layers, carbonaceous material, and organic matter. Most of the metal constituents decreased to background or near-background concentrations in the farthest downgradient well.

Jan 1, 2010

By H. Fujihara, K. Uesugi, H. Toda, A. Takeuchi, K. Shimizu

"Hydrogen is trapped at a variety of microstructures, for example grain boundaries, dislocations and particles. It is thought that hydrogen trapped at trapping sites is redistributed to the other sites under loading and then brittle fracture occurs with hydrogen accumulation. In order to understand hydrogen embrittlement behavior, it is necessary to investigate the time evolution behavior of hydrogen accumulation at each trap site. In the present study, changes in hydrogen distribution are observed under stress using Kelvin force microscopy (KFM) that can visualize hydrogen concentration distribution on material surface at high resolution. Spot-like hydrogen enriched regions are observed on the surface of a material. In addition, hydrogen depleted regions are observed around those enriched regions, and the appearance of hydrogen trap due to particles existing near the material surface is revealed. On the other hand, hydrogen trapped at grain boundary can be visualized. From in this result, it was suggested that crystallographic factors influence hydrogen accumulation. The relationship between initiation and propagation of intergranular crack and hydrogen accumulation under stress will be discussed.INTRODUCTIONHydrogen present in a metal sometimes has significant effects on various properties. Hydrogen in a metal is trapped at a variety of microstructure, for example dislocations and grain boundaries. Grain boundaries, dislocations and micro pores are the major trap sites in aluminum alloys. Some researchers considered that hydrogen redistribution and accumulation between these trap sites in a material with loading plays an important role in the brittle fracture behavior. In general, in intergranular fracture and quasi-cleavage fracture, the hydrogen trapped at grain boundaries and dislocations contributes to fracture behavior, respectively. Recently some researchers have shown that the ductile fracture in aluminum alloys is resulted from growth and coalescence of hydrogen micro pores. Analysis using first principles calculation indicates that intergranular fracture occurs when hydrogen concentration reaches 20 atom H/nm2ongrain boundary. From this report, it is considered that hydrogen redistributed during deformation accumulates locally in order to cause hydrogen brittle fracture. In order to understand hydrogen embrittlement, it is necessary to investigate the time evolution behavior of hydrogen accumulation at each trap site. In the present study, we evaluate the relationship between hydrogen accumulation behavior and fracture behavior in Al-Zn-Mg based alloys. In-situ observation was made by combining the tensile test with Kelvin force microscope (KFM) that can visualize the hydrogen concentration distribution on the material surface with high resolution. We also investigate the relationship between hydrogen distribution behavior and crystal orientation."

Jan 1, 2018

By D. S. Richards

Computers have revolutionized the collection of data on modern mines. Never before has it been possible to collect data from all aspects of the mining value chain at rates now common. With this has come a new challenge. Deriving information from these copious amounts of data and disseminating it. This problem is being exacerbated by technical software systems, which use proprietary and binary data formats that severely inhibit the flow of data and information both across departments and the larger organization. Generally this had led to data duplication and data redundancy. The Gemcom Enterprise Mining System (GEMS) makes use of industry standard, secure and open databases for all its data objects. It manages multiple users accessing the same bits and bytes in the database, preventing data duplication and redundancy. Developed in the Microsoft BackOffice ® environment, GEMS is also able to leverage the enormous amount of tools available in this environment, whether it’s for e-mail notification, reporting or data capture. Microsoft’s® Active Server Pages are one of these tools. These are standards used to create dynamic and interactive web pages with links into databases and many other objects. The real example outlined in the text, demonstrates how a user anywhere in the world is able to login to a web page and run a query that returns a report with vector plots of performance for the user-selected time frame. As integration is tightened between the various components of the mining value chain, the importance and reliance on ASP pages will grow as the need for management information tools develops. Keywords: mines, computers, ASP, GEMS, integration, Microsoft, Management Information.

Jan 1, 2003