Search Documents

By M. A. Hammer

In this study by the Federal Bureau of Mines Pennsylvania anthracite from the Eastern Middle field was oxidized by concentrated nitric acid at steam-bath temperature for 24 to 1,000 hours. The quantitative data obtained include yields of nitric-acid soluble and insoluble products and the distribution of carbon and ash in each. The acid-insoluble residues were examined for solubility in aqueous sodium hydroxide. With a sodium hydroxide concentration of at least 1 normal, a portion of the residue could be extracted in the form of a true solution. With lower alkali concentrations, peptization occurred. Alkali solubility of the residue increased with length of oxidation. However, when expressed in percentages of original coal weight, the alkali solubility remained essentially constant after 192 hours of oxidation. This suggests that the alkali-soluble products are converted to acid-soluble products at the same rate as the original coal substance is converted to alkali-soluble material. Microscopic observations of the peptization of the acid-insoluble residues revealed a gross micellar physical structure. The action of nitric acid is apparently not restricted to the surface of a coal particle. The acid penetrates the particle through the pore structure, dissolving some of the ash and altering the bonds between the coal micelles. The bond alteration, as indicated by ultimate analyses, involves the physical and chemical adsorption of the components of nitric acid. Some of the altered bonds are not thermally stable; this instability is shown by the complete loss of peptizing ability when the acid-insoluble products are heated above 200° C. This loss is accompanied by the evolution of water, oxides of nitrogen, and hydrocyanic acid.

Jan 1, 1961

By Gunhild Hennum, Tewodros Tefera, Gisle Håland, Annette Jahr

"Abstract The Gudrun field is located west of Stavanger in the North Sea at water depth of 109 m. A jacket substructure was selected to support the topside and was installed in 2011. The jacket shall be able to support 16 of 0.762 m (30 in) diameter conductors and is equipped with a drilling deck to allow for pre-drilling by a jack-up rig through the jacket. In general the soil conditions below mudline comprise of a thin top layer of very loose to dense sand overlaying several layers of sandy clay, ranging in stiffness from firm to hard. Below some 30 m depth the soil consists of layers of medium dense to dense silty sand overlaying very hard sandy clay containing thick beds of sand to 100 m depth or more below mudline. The jacket is secured to the seabed by twelve 2.438 m (96 in) diameter steel pipe piles, three at each pile cluster located at the four legs of the jacket at sea floor. Different design methods were used to determine the pile penetration depth. Pile drivability was evaluated using best estimate and upper bound soil parameters. The pile driving and blow count record show that the target penetration was reached as predicted. This paper discusses the different methods used to determine the pile capacity, target penetration depth and the drivability analyses made for the Gudrun jacket piles. The soil resistance during pile driving is back-calculated from the pile installation data and compared with the prediction made.IntroductionThe Gudrun platform is located west of Stavanger in the North Sea at water depth of 109 m. A jacket substructure was selected for the Gudrun platform. The general Gudrun platform jacket configuration is to a large extent dictated by the topside layout, the requirements for support points enclosing the well slots and access for the jack-up rig. The Gudrun platform jacket is a traditional 4 legged structure with a vertical side towards the jack-up rig. At the seabed the jacket is quadratic with a base dimension of 40 by 40 metres. Figure 1 shows the Gudrun jacket during load-out from the fabrication yard to the transport barge. At the site the jacket was lifted off the barge, upended and placed on the seabed by the installation vessel. The jacket is secured to the seabed by twelve 96"" (2.438 m) diameter steel pipe piles, three at each pile cluster located at the four legs of the jacket at sea floor. The target penetration of the piles is 47 m."

Jan 1, 2014

The HYC mineral deposit at McArthur River is about 1.5 kilometres long by 1.0 kilometres wide and 55 metres thick, and contains 227 000 000 tonnes of ore of average grade 9.2% Zn, 4.1% Pb and 41 g/t Ag. Major studies have been carried out continuously since 1955 over the deposit and in the general region. This work is continuing. A small underground mine was developed by driving a decline tunnel to intersect the mineralization 80m below the surface. This provided a fully representative sample of the total deposit unaffected by weathering or oxidation, and was available for the major test program carried out in a pilot plant built to determine the full metallurgical charac- teristics of the ore. The pilot plant operations followed investigations by research institutions, both in Australia and overseas, into the problems of this ultra-fine grained ore. The ultra-fine grained nature of the ore required grinding to an average size of 95% passing 37 micro metres or 400 Tyler mesh. A major feasibility and environmental report was submitted to the government covering all aspects of a development program. The geological, engineering, metal- lurgical, economic, cultural and environmental submissions contained in this report were studied by external consult- ants employed by the government, who agreed with the conclusions that the McArthur HYC deposit is at present Uneconomic.

Jan 1, 1984

By James A. Finch, Stéphanie Somot

"The self-heating facility developed at the Noranda Technology Centre [Rosenblum and coworkers, 2001; 1995] has now been established in the Department of Mining, Metals and Materials Engineering at McGill University. A research program into mechanisms has been initiated (with support now from four industrial partners under Camiro). The first investigation is into the role of pyrrhotite (Po), the most commonly suspected mineral to trigger self-heating. Following a standard experimental protocol, self-heating was assessed on samples of Po mixed with sand as an inert material. With increasing Po content, self heating progressively increased but, interestingly, the samples visually appeared less and less oxidized. A high Po content, it was hypothesized, may give a more reducing environment favouring formation of H2S. The presence of this gas could be significant as it has a high exothermic heat of reaction with oxygen. The system was modified to test the hypothesis by including copper pieces and copper sulphate to react with (and therefore reveal) the gas as copper sulphide. Evidence is presented in support of H2S production, which to our knowledge has not been shown before and introduces a potentially important avenue of investigation into self-heating mechanisms.INTRODUCTIONSelf-heating of sulphide minerals poses potential environmental and safety hazards in mining of ores, and storage and transport of concentrates. While some conditions are known to be critical, the reactions remain poorly understood making self-heating difficult to predict and control.A major advance in measurement was introduced by Rosenblum and co-workers [Rosenblum et al., 2001; Rosenblum and Spira 1995]. A self-heating assessment method was developed and applied to various sulphide-bearing materials The method is based upon automated calorimetric cells with data acquisition, now available to McGill researchers and which have been used for the study reported here."

Jan 1, 2006

By R. F. Pearce

The paper in based on laboratory and pilot plant investigations which led to the development of a series of processes for production of high purity metals from nickel-copper-cobalt mattes of a wide range of composition. The selection of ammonia pressure leaching or acid pressure leaching for various mattes is discussed. This is followed by discussion of various methods for leach solution purification and metal separation. The metals of high purity are produced by reduction with hydrogen from purified solutions. Examples are given of complete flowsheets for a number of mattes. Drawing upon those examples, general principles for the selection of the most suitable treatment process for particular material are outlined. Under certain circumstances, those processes may replace part of the pyrometallurgical treatment and all of the electrolytic refining steps which are customary in the treatment of nickel-copper-cobalt mattes.

Jan 1, 1959

By J. L. Page, A. C. Marlowe

The Research and Development Services of South Africa has begun underground trials with a Robbins 52RE blindhole borer using a cutterhead fitted with high pressure water jets to assist mechanical cutting. The objectives of the work are to reduce cutter costs by increasing cutter life and to increase overall penetration rates. The paper reviews blindhole boring in South Africa and laboratory experiments in rock cutting assisted with high pressure water jets. The borer and its ancillary equipment are described. Initial results of underground boring experiments are presented. The paper concludes with the test programme for the future.

Jan 1, 1985

The extremely cold weather and heavy snowstorms of January and February in northeastern Pennsylvania--with frozen mining equipment, diminished preparation and lack of railroad cars--severely hampered the production and distribution of anthracite. As a result, the previous estimates for the 2 months have been revised. On March 1, 1977, at the Porter Tunnel of the Kocher Coal Company at Tower City, Pa., an underground flash flood, which apparently broke through the wall of an adjoining abandoned shaft, swept through the mine. As of March 9, 1977, four miners were reported killed, three injured, and five trapped in the wreckage. The Kocher Coal Company began operations at the Porter Tunnel in 1968 and has had no fatalities until this current tragedy. The mine employs 20 persons on the surface and 115 miners underground, producing 750 tons of coal per day. Of the 109 underground mining operations in the anthracite region, this is the one remaining large mine that employs over 100 men.

Jan 1, 1977

PRESIDENT GEORGE OTIS SMITH, District 4 WASHINGTON, D. C. PAST PRESIDENTS SAMUEL A. TAYLOR, District 3 PITTSBURGH, PA. E. DEGOLYER District 0 NEW YORK, N. Y. FIRST VICE-PRESIDENT W. H. BASSETT District 1 WATERBURY, CONN. TREASURER KARL FILERS NEW YORK, N. Y.¬ SECRETARY H. FOSTER BAIN NEW YORK, N. Y.

Jan 1, 1923

By Andreas Eberhorn

The evaluation criteria for cost comparison of the Gearless Drive, also called Ringmotor or wrap-around motor, as variable-speed drive with a Twin Drive System using synchronous motors are reviewed. Both mechanical and electrical components of the drive system are considered. The evaluation criteria are described and for the cost comparison the applicable method is demonstrated. The cost comparison is based on a medium and large sized mill system. Each drive package will display cost details with regard to capital cost, maintenance, power losses, overall efficiency, overhead and loss of production. As conclusion the benefits and disadvantages of the two drive/mill packages will be presented together with a payback diagram.

Jan 1, 1996

By V. P. Keran, K. Leung

Two 32 foot x 14% foot, 6.4 MW autogenous mills have been installed in the Mount Isa Mines Copper Concentrator to replace the fine crushing plant, fine ore bin, rod mills and primary ball mills. This paper describes the reasons for the change, the rationale for the new circuit design and configuration, the design and scale-up processes used to size the mills, considerations for the installation of large mills inside an operating concentrator and some early operating data.

Jan 1, 1992

By Richard P. Stahura

During the next five years, there will be a trend toward performing belt cleaner maintenance while the conveyor is in operation. Most mines and industrial sites that use belt conveyors have an in-house safety rule that the belt must be stopped before maintenance work can be performed on any belt-cleaning device. This is a good rule. Most cleaning devices are positioned against the belt with hardware that requires the service technician to reach or climb into the chute to change the cleaning blades. But this simple rule becomes more complicated as production demands require higher conveyor availability and provide fewer conveyor outages. In many cases, today’s conveyors are expected to be available 98% to100% of the time.

Jan 1, 1996

By Kokubu H, Moro-Oka A

Gaseous desulphurization from hot metal- lurgical slags containing sulphur mainly as sulphide and(or) sulphate was measured under `low at four different oxygen pressures. The total gas rate was from 1.7 to 2,8 litre/min. Crushed slag samples weighing 2 to 12 g were used for the experiments. The amount of SO2 gas evolved from samples kept at 15500 was rieasured over tires ranging from 20 to 300 min. The gaseous desulphurization rate of sul- phide sulphur becomes high as the oxygen part- ial pressure is increased, while that of sul- phate sulphur is high under low oxygen pressure. The effect of basicity on the desulphurization rate of sulphide sulphur in oxygen atmospheres is not obvious in the range of basicity from one to three. Changes in the ratio of sulphide to sulphate sulphur during the run in oxygen axe analysed. Desulphurization reactions and the rate controlling steps are discussed. De- sulphurization phenomena can be explained by inte.-¦ucia.l chemical reaction rate control.

Jan 1, 1980

By K. G. (Ken) Thomas

"This paper gives an insight into the various processes available to treat gold ores. A brief overview is given of the various types of refractory gold ores. Particular emphasis is given /0 comparing the costs of oxide vs refractory gold ore processes, inclusive of grinding through to dore bar.HistoryThro ugh time gold has been recovered from the earth's crust by various mean s. Five major historical steps can be identified for metallurgical processing as shown in Table I .Gravity concent ration started with, for example, river bed panning and developed to more sophisticated processes such as the Johnson concentrator, belt concentrator and jigs. The South African gold fields were a major developer of gravity concentration processes during the first half of the twentieth century.As coarse free gold became depleted, stamp milling, in conjunction with amalgamat ion , was developed. Basically, rock was crushed under large mechanical hammers an d the gold collected in mercury . The mercury was then evaporated in a retort to leave sponge gold for further fire refining.As deposits became deeper and gold finer, the gold became more difficult to recover ; fine grinding was required to liberate the gold. In the 18905, MacArthur and the Forrest Brothers of Glasgow, Scotland, introduced the cyanide pro cess for dissolution of gold and its subsequent precipitaiton by means of zinc. This process, in vogue until the early 1970s, was commonly referred to as the Merrill-Crowe process for recovering fine gold .Activated charcoal was used as a means of recovering gold from solution in the 1880s, especially in chlorination plants in Australia( l). Two factors probably retarded the development of carbon instead of zinc-based processes during those year s. First , there was no satisfactory procedure for the elution of carbon to allow its recycling and, second, the development of the Merrill-Crewe process for gold recovery by zinc cementation probably discouraged any further work on the use of carbon"

Jan 1, 1991

By Jenq-Gong Duh, Jyh-Wei Lee

"Hard chromizing process is a method for developing a surface modified coating providing wear, corrosion resistance and high temperature surface protection. Two carbon steels with 0.45 wt% and 0.95 wt% carbon contents, respectively, were chromized with pack cementation process at 950'C for 4 and 9 hours, respectively. The phase transformation and microstructure phenomena of chromized coating layer and matrix of two steels were studied with X-ray diffractometer and electron probe microanalyzer. (Cr,Fe)23C6 and (Cr,Fe)7C3 carbides and (Cr,Fe)2N1-x nitride phases were observed on the chromized surfaces. The thickness of chromized layers obeyed the parabolic rate law. The mechanism and diffusional kinetics of the chromizing process were proposed. The diffusivity of chromium in the (Cr,Fe)7C3 carbide phase was calculated using the moving boundary method.IntroductionChromizing process is one of the surface treatment technologies that can produce a chromium contained surface layer with sufficient corrosion and wear resistance on the steel matrix [1-7]. The relatively low cost and no ""line-of-sight"" restrictions are main advantages of chromizing. Adequate bonding strength of these coatings to the substrate was reported [7]. Chromizing process can be classified into soft chromizing and hard chromizing [2]. Soft chromizing is applied to steels containing less than 0.1wt% carbon through which chromium will be diffused. High temperature oxidation resistance improvement is the main purpose of soft chromizing process. On the contrary, the hard chromizing can be applied to steel containing more than 0.3wt% carbon, and very hard chromium nitride and carbide layers will be formed on the surface, which are very resistant to wear, corrosion and temperature [5-7]. In the previous studies on the Fe-Mn-Al-Cr alloy [5,7] and carbon steels [6], the thickness (X) of chromizing layers was analyzed and found the parabolic rate Jaw prevailed:"

Jan 1, 2004

By R. S. Dean

The careful work of Gross and Zimmerleyl has established the fact that the energy actually used in grinding is proportional to the new surface produced. This confirmation of Rittinger's law was made by crushing quartz in a frictionless drop-weight machine and determining the surface of the quartz by its rate of solution in hydrofluoric acid. The details of this procedure have been described adequately elsewhere and need not be repeated here. The resultant data furnish the only available basis for comparing accurately the efficiency of grinding machines. This method is so cumbersome experimentally that it has been little used. As an alternative all sorts of approximations have been proposed. The best of these is complete size analysis by sieving and elutria-tion. Such procedure is very lengthy and difficult to carry out accurately. Furthermore, any sizing method becomes very inaccurate for determining surface with very fine sizes where the ratio of surface to volume becomes very large. To avoid the lengthy and difficult technique of elutriation it has been proposed to estimate the size distribution below 200 mesh from various probability formulas. Such a procedure is at best an engineering approximation; at worst it is a mere guess. Some time ago Dr. V. H. Gottschalk2 found that the coercive forces of magnetite powders were directly proportional to the surface area, regardless of size distribution. It was at once apparent that this furnished a method for determining grinding efficiency quickly and accurately. The only requirement was a single determination of the relation between the work input of the Gross-Zimmerley drop-weight machine and the coercive force of the resultant crushed magnetite. For this purpose Ural Mountain magnetite in definite octahedra was

Jan 1, 1939

By J Player, K Braddon

High productivity mining is the key to the financial success and stability of modern mines. This can be achieved through the use of new technologies, the development of innovative work practices andoptimisation of the mining method to suit the mining environment.Big Bell Mine is a 1.7 Mtpa longitudinal sublevel caving operation at a head grade of 3.14 g/t. Annual production is 170 000 ounces of gold. The selection and implementation of bulk emulsion explosives was seen as the logical progression from blow loaded ANFO for the high tonnage rate required from the longitudinal sublevel cave.Prior to the implementation of bulk emulsions an investigation wasrequired to examine the technical and financial benefits available with the introduction of bulk emulsion. This paper examines the review process and the successful implementation of bulk emulsion explosives at Big Bell.

Jan 1, 1999

By In-Kuk Bae, Kwang-suk You, Joobeom Seo, Kwanghyun Bea, Hyung-Seok Kim

Arsenic in base metal sulfide ores is highly penalized owing to high costs for its control in metallurgical processing. The arsenic element in the lead-zinc ore, which is target ore in this study, has been shown to be in the form of arsenopyrite. Experimental work in this study is about arsenic rejection flotation, using depressant suitable for the removal of arsenopyrite from the Pb concentrate. The arsenic rejection flotation also included the oxidation treatment of Pb concentrate with H2O2. In this study, the Pb concentrates containing 80.7% Pb and 0.25% as was obtained with the additions of aluminosulfate as arsenic depressant. And through IR measurement, it was also known that the addition of aluminosulfate during arsenic rejection flotation formed calcium aluminosulfate hydrates on the surface of arsenopyrite particle, resulting in rendering arsenopyrite hydrophilic.

Jan 1, 2014

By Frederic Benard

RECOVERY of selenium and tellurium at Copper Cliff by the Ontario Refining Co. has been previously described by the writer.1 During 1935 a new building was erected to house this operation and description of the new plant and process form the subject of this paper. The building, of modern steel and tile construction, covers an area of 5900 sq. ft. with a volume of approximately 165,000 cu. ft. The large monitored center bay is flanked by two smaller outside bays, one of which is devoted to the tellurium section. All equipment, ceilings and upper walls, are treated with aluminum paint, giving good illumination and facilitating good housekeeping, essential from a health standpoint in handling material of this nature.

Jan 1, 1938

By George D. Lessner

I'm sure that everyone at this meeting is aware of the current problems facing the U.S. metals mining industry. Prices are depressed and expected to remain depressed for quite some time. On the other hand, industrial minerals, including talc, are doing quite well. The profitability of industrial minerals has sparked considerable interest on the part of many companies in expanding into industrial minerals. Our company is one of those actively seeking to expand its position in industrial minerals. It is appropriate that the A.I.M.E. asked me to speak to you regarding entry into the talc business. So how do you get into the talc business? Earlier speakers have explained how to locate, mine, process, and market talc, so you have the "how ton.

Jan 1, 1984

By J-F. Turgeon, Y. Pépin, G. Hudon

The high temperature hydrochloric acid leaching of titanium slag in the QIT upgraded slag process (UGS) creates a harsh environment for materials of construction. Because of their excellent chemical and heat resistance, furan mortars are a key component in the lining system of the UGS pressure leach reactors. Similar products coming from different manufacturers have however shown unequal performances in service. In some cases, cracking of the brick lining has occurred during curing of the mortar. This study was initiated to investigate the impact of the curing conditions on the properties of carbon filled furan mortars. Laboratory tests were conducted to assess the effects of temperature and exposure to water and HCl solutions on mortar shrinkage and mechanical properties (tensile, compressive and bond strength). Three commercial furan mortars that have been used in the UGS leach reactors were thus characterized. Mortar properties were found to vary significantly among the products tested. Moreover, the curing conditions were shown to have a significant impact on mortar shrinkage and mechanical strength. The experimental findings provide explanations for the unequal performances of the mortars in service and for the problems of brick lining cracking that occurred in the UGS leach reactors. This study demonstrates that excessive mortar shrinkage compromises the integrity of a brick lining system.

Jan 1, 2004