Search Documents

By Brian W. Mackenzie

The mineral exploration environment has observable economic characteristics, the assessment of which provides guidelines for exploration planning in the mining company. The long-term survival of the mining company is directly dependent on successful exploration. Exploration planning contributes to successful exploration through the development of exploration strategies. The objective of exploration planning is to select exploration environments which will enable the mining company to realize best possible profit and corporate risk conditions. Thus, the formulation of exploration strategies is based on profit and corporate risk criteria. Strategic considerations include the selection of commodities as exploration targets, geographic concentration of exploration effort, the realization of acceptable survival conditions, and the structuring of an exploration programme to optimize the economic benefits of the exploration investment process.

Jan 1, 2014

By David F. Gearhart

A cooperative study was conducted between Signal Peak Energy and the National Institute for Occupational Safety and Health (NIOSH) to evaluate the behavior of a pre-driven recovery room under less than 200 ft of cover. The design of the support systems for a pre-driven recovery room must provide control of the roof and ribs during the changing stress environment experienced throughout the final advance of the longwall into the recovery room. It must also provide a stable area where mine personnel are not exposed to undue hazards during shield recovery operations. This recovery room was constructed in two phases; each phase mined a 21-ft-wide room that was heavily supported, and subsequently fully backfilled with 800-psi, cellular concrete. Instrumentation to monitor the recovery room performance included borehole pressure cells (BPCs) placed in the head gate and tailgate pillars, at four locations across the longwall panel, in the fill material, and in the first row of outby pillars near the center of the panel. Four roof-to-floor convergence sensors were installed in the back fill material and a vertical, multipoint borehole extensometer (MPBX) measured the displacement of the strata above the recovery room. Surface surveys were conducted to measure MPBX collar movement. The data show that the front abutment load was transferred onto the recovery room backfill and the out by pillars as the longwall panel was extracted. As the longwall approached the recovery area, the fender and shields yielded, but the backfill provided enough support to keep the room stable as the longwall advanced to its final position. The system worked as planned and the face was recovered in record time.

Jan 1, 2014

By Joshua Calnan, Braden Lusk, Kyle Perry

This paper presents detailed information and data regarding the load transfer characteristics of Blast Resistant Glazing Systems utilizing two different thicknesses of polycarbonate. A series of triaxial load cells, along with surrogates of identical stiffness characteristics, were placed around the glazing perimeter to directly measure the load transferred to the support system from explosions of varying degrees. The blast loads were developed using an explosive driven shock tube administered by the University of Kentucky Explosives Research Team (UKERT) in Georgetown, KY. Results presented include distribution of loading, maximum load transferred to connections, blast pressure-time data, glazing system deflection-time data, and final performance results of each system. The two glazing systems respond differently to the applied blast loading. Differences and similarities in the load transfer characteristics are discussed. The experimental results are then compared to a commonly used blast resistant glazing system analysis software tool utilizing a Single Degree of Freedom (SDOF) method of analysis for each system. Preliminary results show that currently used models do not correspond well with experimental data.

Jan 1, 2014

By Xianzhong Hu, Qingbo Yu, Qin Qin

"Oxy-fuel combustion is one promising option among different CO2 capture technologies. The object of this work is to show the effect of CO2 dilution on the laminar flame speed, flame structure and reaction pathway for methane oxidation at O2/CO2 atmosphere. In this paper, kinetic simulations were made using CHEMKIN with GRI-Mech 3.0 mechanism, which was validated by experimental data of laminar flame speeds. The reaction pathway of CH4/O2/CO2 mixture was derived from reaction flow analysis. Results showed that CO2 decreased the flame speeds, lowed concentration of major intermediates and increased flame thickness. The major chemical pathways of CH4 to CO2 have not changed at O2/CO2 atmosphere comparing with O2/N2 atmosphere, but contributions to major intermediates formation from each related elementary reaction have changed a lot. In addition, the secondary chemical pathways of CH3 oxidation became different at O2/CO2 atmosphere.IntroductionNowadays, as the global economy is developing fast and the pollutant levels (especially global warming gases) are increasing, a lot of researches are focusing on new technologies which can cut greenhouse gas emissions [1]. New technologies have been developed, such as high Mild combustion, flameless combustion and Integrated Gasification Combined Cycle (IGCC) technology. Oxy-fuel combustion using carbon dioxide as dilution of oxygen is considered as a promising approach for reducing CO2 emission. The properties of CO2 in flue gas are different from N2 in air. On one side, the transport, thermal and radiative properties of CO2 are different from N2 in air. On the other side, CO2 is not inert but directly participates in chemical reactions and recent researches [2-5] also present the chemical effects of CO2 on oxy-combustion. For these differences above, the characteristics of oxy-combustion are not alike with traditional combustion. It is necessary to develop the investigation of oxy-combustion.In all combustion processes, laminar flame speed is an important parameter, which links to combustion behavior. Analysis of this parameter can provide a better understanding of the effect of CO2 dilution in the process of oxy-combustion. Several investigations of laminar flame speeds of oxy-fuel flame have been improved, including experimental measurements and numerical computations. A.A.Konnov et al. measured the flame speeds of oxy-methane and oxy-ethane mixture using the heat flux method with a flat burner [6-8]. V. Ratna Kishore et al. used heat flux method to measure the adiabatic laminar flame speeds of hydrogen [9] and H2/CO mixture [10]. Adiabatic laminar flame speeds of hydrogen in O2/CO2 atmosphere are much smaller than in O2/N2 or in O2/Ar. The burning velocity of H2/CO mixture decreased with increase in CO2 content in mixture. Jeongseog Oh et al. [11] used Bunsen flame to measure the laminar flame speeds of premixed oxy-methane mixture with angle methods in atmospheric condition (300k, 1atm). The results were SL=29.1cm/s and SL=29.5cm/s respectively derived from oxy-methane from CH* images and Schlieren photos."

Jan 1, 2014

By G. T. Lapidus, O. J. Solis-Marcial

Currently, ores with high-grades of copper oxides and secondary sulfides have become increasingly scarce, which has encouraged industry to look for alternative raw materials to obtain copper. The problem is that primary sulfides are difficult to dissolve at near ambient conditions. Proposed hydrometallurgical processes have not been implemented beyond a pilot or demonstration scale. One of the principal disadvantages is that the majority of these processes are not viable with ores that contain less than 4% copper. One of the more recently proposed techniques involves the use of organic solvents in the dissolution of copper concentrates with a chalcopyrite content of between 20 and 30%, which has shown high efficiency. The present research explores the ability of this process to leach copper from low grade chalcopyritic ores (<4% Cu) at different temperatures ranging from 20 to 50°C. It was found that depending on the temperature, high percentages of copper were extracted in 40 to 100 minutes, using different oxidants. Additionally, distinct leaching behavior was observed with each oxidizing agent. In some cases, the extraction kinetics adjusted to the diffusion controlled shrinking core model.

Jan 1, 2014

By Sergey Gudkov, Yuri Yemelianov, Stanislav Balikov, Andrey Boldyrev, Andrey Bogorodsky

"The results of POX of refractory gold-bearing concentrates using halide-ion as a lixiviant for precious metals and activated carbon as an adsorbent are given. It was found that gold did not recover to the solution when halide was added during POX. Silver partially dissolved in the solution. When halide-based reagents and activated carbon were added during POX, gold dissolved and loaded onto the activated carbon. The degree of sulfides oxidation was 99.3-99.6%. The recovery of gold onto granulated carbon was 94.7-94.8% when using chlorine-bearing lixiviants: NaCL, CaCL and carnalite and 98-99% when using KJ and KBr. This treatment process of refractory gold-bearing concentrates combines sulfide oxidation, dissolution and adsorption of precious metals. The results of the metals recovery achieved using this process can be compared with the recovery during POX-cyanidation. In this case, sodium cyanide was not used. This allows the reduction of capital and operational costs due to the absence of cyanidation, CIL and detoxification of leaching tailings circuits."

Jan 1, 2014

By Komar Kawatra, Joseph Halt

"Bentonite clay has been the traditional binder for iron ore pellets. However, bentonite increases pellets’ silica contents and is expensive. Researchers have proposed lowering bentonite doses by mixing it with other common binders. These mixtures may only be successful if the fundamental bonding mechanisms are understood. For example, what happens when bentonite (physical bonding) is mixed with fly-ash (chemical bonding)? What happens when bentonite is mixed with cornstarch (physical bonding)? In this paper, experiments are described where bentonite was mixed with various ratios of cornstarch and fly-ash, and pellets were agglomerated using 0.66 % w/w binder. Ca(OH)2 and CaCl2 were added as activator and accelerator, respectively, to the bentonite-fly ash mixture. Curves of pellet dry strength vs. bentonite-starch ratio were linear, suggesting the physical-physical bonding mechanisms were compatible - acceptable strengths (> 22 N) were produced at all bentonite-to-starch ratios. This was contrary to bentonite-fly ash mixtures, which displayed dry strength curves with a noticeable minimum due to competing binding mechanisms. Bentonite alone and fly ash alone produced acceptable strengths (> 22 N), but their mixtures resulted in weak pellets. Due to the positive results using cornstarch (CS) binders, the effects of CS solubility in water were investigated using two CS with high and low solubility (60 and 7.5 %). CS was premixed with bentonite at various ratios (0, 20, 40, 60, 80, 100 %). Pellets were agglomerated using 0.66 % w/w binder. The dry strength of pellets ranged from 50-300 N using the high solubility CS mixtures, and from 50-85 N using the low solubility CS mixtures. Fired strengths exceeded 2200 N/pellet at all bentonite-cornstarch ratios. This research showed that cornstarch solubility is an important factor in determining its effectiveness as a binder for iron ore concentrates, but significant work is still necessary before it can be used as a bentonite replacement."

Jan 1, 2014

By Paivi Suikkanen, Kari Hietala, Kaarlo Haavanlammi

"Processing of high-magnesia concentrates, the recoveries of nickel and copper, as well as those of platinum group metals (PGM’s) and cobalt are key issues of the Nickel Smelting technologies. PGMs are typically found in association with each other, but also importantly with nickel and copper. A challenge of producing saleable concentrates at acceptable recovery degrees, an increasing focus on the sustainable use of metals and recent decreases in the value of nickel has increased the interest to find a reliable route from Cu-Ni-PGM bulk concentrates to product. According to studies, most efficient process for Ni-Cu-PGM concentrates is flash smelting using DON process20 years ago, in 1995, Outokumpu commenced at Harjavalta a new Nickel Flash Smelting technology based on the Direct Outotec Nickel (DON) Smelting Process. The DON process enables production of high-grade nickel matte with low Fe-content directly in the Flash Smelting Furnace (FSF) without subsequent converting. Metal values from the smelting slag are recovered in the Electric Furnace (EF) as iron containing Ni-matte. Matte refining is based on atmospheric pre-leaching and total pressure leaching. Nickel, cobalt and iron are leached leaving a leach residue containing small amount of gangue minerals and PGM’s. Iron is removed from the leach solution in and nickel will be recovered with standard methods. Overall > 95% metal recovery can be expected with low energy consumption and low environmental impact."

Jan 1, 2014

By C. Y. Wang

Anodic reaction mechanism of complicated antimony-lead concentrate in Slurry Electrolysis has been investigated by the anodic polarization curves determined under various conditions. The main reactions on the anode are the oxidation of FeCln (2-n), though the oxidation of jamesonite particle on the anode can occur during the whole process, it is less. With the help of mineralogy study and relevant tests, the leaching reaction mechanism of jamesonite and gudmundite during Slurry Electroly-sis has been ascertained also. Because of the oxidation reaction of FeCl3 produced by antimony-lead concentrate itself, the non-oxidation complex acid dissolution of jamesonite, the oxidation complex acid dissolution of gudmundite, and the oxidation of air carried by stirring, the leaching ratio of antimony reaches to about 35% when using HCl-NH4Cl solution to leach antimony-lead concentrate directly. So given the theoretical electric quantity, which to oxide antimony in Slurry Electrolysis, all of antimony, lead and iron, which contained in antimony-lead concentrate, are leached.

Jan 1, 2014

By G. K. Nimal Subasinghe

The performance of Knelson Concentrators (KC) used in gravity gold circuits often rely on manufacturers recommendations for selecting operating parameters such as, fluidising water flow rate and cycle time. These parameters are not only dependent on the machine parameters but also on the feed characteristics such as, size distribution of the gold and gangue particles and the composition of its constituent minerals. Particles entering a KC experience a centrifugal acceleration due to the high bowl rotational speeds. The required centripetal force to maintain a circular orbit is provided by the fluid drag force created by inwardly moving fluidising water and the Bagnold?s force arising from the particle/particle collisions. When the fluidising water flow rate is low particles move towards the outer rim of the bowl forming a packed bed within the grooves. On the other hand, if the fluidizing water flowrate is high the bed expands and some particles would move towards the centre of the bowl and gets carried to the tailings stream, thereby reducing the amount of material retained within the grooves of the bowl. Based on a force balance on a particle captured within the KC, a criterion which can be used to predict the amount of material recovered in the bowl has been derived and validated by experimental data. It has been shown that this criterion may be used to demarcate the transition of the bed from a packed-bed state to a fluidised state depending on the fluidizing water flowrate. By identifying the conditions for the optimal expansion of the bed comprising different constituent mineral particles, it is possible to estimate the optimal fluidising water flow rate that would maximise gold recovery while minimising gangue recovery. It was also observed that the accumulation of valuable mineral in the bowl takes place by the displacement of the gangue particles in the bed by the incoming heavy mineral particles. The kinetics of this segregation process was also studied using synthetic mineral mixtures. The experimental data suggests that this process follows first order kinetics and that the build up of heavy mineral reaches a maximum which could be used to identify the optimal cycle time. In this work, the suitability of the above model in optimizing the performance of a KC have been reviewed. Also the necessity and merits of testing an unaltered feed samples in a larger KC as op-posed to the commonly adopted GRG test has been discussed.

Jan 1, 2014

By M. Steyn

The coordination compound tetrakis(1,3-diphenyl-1,3-propanediona to)zirconium(IV), [Zr(DBM)4], (DBM = dibenzoyl methane/1,3- diphenyl-1,3-propanedionol) was synthesized and characterized by single-crystal X-ray diffraction. [Zr(DBM)4] crystallizes in the monoclinic space group P21/c (a = 24.769(4) Å, b = 10.216(5) Å, c = 19.314(4) Å, and = 101.541(5)°). The coordination geometry around the zirconium atom, formed by the eight O-donating atoms of the four -diketonates, is found to be a near-perfect square antiprism. Crystal packing is stabilized by C?H... interactions throughout the crystal lattice. This structure is a noteworthy example of the application of ambient condition synthesis of zirconium compounds in N,N&apos;-dimethylformamide (DMF) as reaction and crystallization solvent, highlighting the possibilities of aerobic condition metal purification through chelation.

Jan 1, 2014

By G. Cockburn

Nkomati Nickel JV exploits the ores of the Uitkomst Complex near Machadodorp in the Waterval Boven district in South Africa?s Mpumalanga Province. Due to factors such as the remote location, stellar growth in production, opencast mining methods, and ore characteristics, a number of innovative processing options were selected. Nkomati has undertaken numerous initiatives over the last few years to improve plant running times, metallurgical performance, and operational profitability. Great emphasis has been placed on effectiveness of management control systems. A number of initiatives such as short interval control and time?in-state metrics have been implemented. A focus on improvement on availability and asset utilization of key items of equipment has been particularly effective. While the ores are remarkably similar to the Merensky and UG2 reefs, the relatively high base metal sulphide content and mineralogical characteristics make metallurgical treatment somewhat different to the ores of the Bushveld Complex. The low head grades and flotation kinetics distinguish Nkomati from other base metal operations. Numerous milling and flotation optimization initiatives have resulted in dramatic improvements in throughput, recoveries, and concentrate grades. This paper discusses the metallurgical, operational, and management challenges and the outcomes obtained.

Jan 1, 2014

By H. Asgari, A. G. Odeshi, J. A. Szpunar

In the current research, the role of grain size on the texture formation and mechanical behavior of rolled AZ31B Mg alloy is investigated under shock loading conditions. The grain size of the original asrolled sample was 8 µm and different grain sizes, e.g. 25 and 46 µm, were produced by heat treatments at temperatures in the range of 400-500 °C. In order to evaluate the effect of grain size on the anisotropy of mechanical behavior, the samples were cut along the rolling direction (RD), transverse direction (TD) and normal direction (ND) and tested at strain rates of 900 and 1200 s-1 using Split Hopkinson Pressure Bar. Texture measurements showed that initial texture of the samples cut from the as-rolled sheet is a weak rtype texture. However, a stronger texture was observed for samples with large grains. After shock loading, a (00.2) basal texture developed in all samples and the intensity of the basal poles was higher in samples with coarser grains. This observation is corroborated by high twinning activity and possible activation of pyramidal <c+a> slip in coarse grained samples. Besides, the strength of basal texture increased with increase in the strain rate. Furthermore, the samples with larger grain size showed lower strength and higher ductility, and this was observed for all investigated strain rates.

Jan 1, 2014

By O. Alonso-Gonzalez, F. Nava-Alonso, A. Uribe-Salas, R. Pérez-Garibay, C. Jimenez-Velasco

A current problem in gold production is the presence of copper minerals which dissolve during conventional cyanidation practice. The dissolved copper causes several problems in the different stages of the process. This issue is the base for copper elimination/recovery methods such as the Sulphidization, Acidification, Recycling, and Thickening (SART) process, which is currently used in gold production plants around the world. Even though the process is well established, new challenges appear as the composition of the solution varies from ore to ore, in some circumstances affecting the performance of the SART process. This work presents a thermodynamic study and experimental tests performed to understand the role of the initial copper concentration and sulfur addition, on the efficiency of the copper removal. For a constant cyanide concentration, an increase in the initial copper concentration causes a decrease in copper removal; high sulfur/copper molar ratios favor copper removal. We demonstrated that the cuprous sulfide formed from solutions with high ionic strength, presents better sedimentation rates than solutions with less ionic strength. For solutions with low sedimentation rates, the use of some pretreatment is necessary to facilitate the sedimentation such as addition of flocculants, particle recirculation and the used ultrasonic pretreatment.

Jan 1, 2014

By G. B. Harris

It has long been appreciated that chloride chemistry has a number of advantages over the more traditional sulphate route for both extracting and separating metals. Modern materials of construction, coupled with the development of a more cost-effective and efficient hydrochloric acid regeneration technology mean that chloride-based processes are now more competitive and attractive. Such processing routes are able to recover more of the contained metal values in a feed, including iron in a benign and/or marketable form, and particularly the so-called rare and rare-earth elements which are increasing in demand in our electronic age. These factors, therefore, add appreciably both to the overall economics of a project, but also offer a much more sustainable approach to our dwindling natural resources. Additionally, chloride-based flowsheets can be much more environmentally-friendly, offering practical alternatives to two of the biggest headaches faced by the industry, namely cyanide usage and the generation of red muds. This paper presents a brief theoretical background, focusing on the latest developments of ferrous iron oxidation and the low-temperature, selective hydrochloric acid regeneration process, which is the key unit operation for any chloride flowsheet, and discusses in general the advantages of the chloride approach. Several recently-developed flowsheets, which have been tested at the miniplant level, are presented for gold, base metals, titaniferous magnetites and lead-silver ores wherein the advantages of considering a chloride approach are highlighted.

Jan 1, 2014

By T. Badrujaman

In September 2005, after 30 years experiencing in operating an ESF using a falling water film shell cooling system, Antam entered the new era in operating an ESF, after completely modernized its ESF No. 2 from a falling water film shell cooling system to a copper cooling system. Further, in the beginning of 2007, Ferronickel plant No. 3, where its ESF also uses copper coolers, was successfully commissioned. By operating an ESF using a copper cooling technology, Antam has to face some challenges to establish the operation stability. Besides that, the chances to maximize the furnace efficiency are greatly opened. The shielded-arc mode of electrode tip is selected to operate an ESF under relatively high furnace power to produce metal having tap temperature below 1500? and slag having tap temperature below 1600?. It leads to electric current unbalance. Further, operating an ESF using a copper cooler system under high voltage as consequence of the furnace power raise increases metal and slag tap temperature. This condition damages furnace integrity fast. Besides that, relatively high metal temperature increases its pressure during metal tapping. It leads to failure in closing the metal tap hole. The main different ways in operating an ESF using a falling water film shell cooling system and a copper cooling system lie in the electrode tip mode, the water specification used for cooler, metal tap block maintenance and allowed metal & slag level in furnace. Since a copper cooler system allows an ESF to be operated by consuming nickel ore having ratio Fe / Ni up to eight and producing slag having relatively high Fe content in slag, an undesirable silicon reversion phenomenon becomes an obstacle in reaching the operation stability. A copper cooler technology lets Antam to take a chance to increase its capacity. Modernizing the ESF No.2 had increased its furnace power from 17 MWh to 25 MWh. Meanwhile the ESF No. 3 can be operated up to 42 MWh. This technology allows an ESF to be operated under relatively high furnace power above 25 MWh safely as well as prolong the campaign life of ESF brick. Further, lowering ESF power consumption, extending the limitation of ratio S/M in nickel ore consumed and adjusting Ni grade in ferronickel product can be gained by applying this technology.

Jan 1, 2014

By X. W. Zhang

Mica plate is broadly used in electric industry, production of man-made mica paper plate is in-creasing. The problem coming with is that large quantities of leftover materials unable to be re-cycled are produced during cutting and molding of mica plate productions. The leftover materials are always abandoned as crabs, which not only pollute the environment but also waste our resources. The study intends to find a new measure to decompose and to reuse the mica plate leftover materials so as to create a new production process of mica plate, which is clean and does not produce crabs.

Jan 1, 2014

By C. Knobbs

Contrary to the way it is often portrayed, the average organization or company is far from being a cold, calculating machine. It is actually a highly emotive place where interaction with people is a fundamental part of its ability to perform satisfactorily. The company, through its employers, expects employees, including new graduates, to have the ability to cope adequately with this emotive environment. The graduate is frequently unable to meet this expectation because he/she has not been developed to do so. Technical knowledge is his only asset. This deficiency manifests itself in leadership shortcomings, both intrapersonal and interpersonal. Further analysis reveals a deficiency in three elements of leadership ? self-awareness, oral communication, and an ability to work cooperatively in teams. To address these three elements of leadership, Sasol Coal, a subsidiary of the big petrochemical company in South Africa, sponsored a leadership programme at the University of Pretoria for their final-year bursary students in the faculty of Engineering. This programme, the Sasol Engineering and Leadership Academy (SELA), consisted of a number of interventions designed to address the three areas of self-awareness, oral communication, and cooperative behaviour in teams. These interventions varied from an intrapersonal nature to interpersonal aspects. Psychometric assessments were followed by experiential modules dealing with the three constructs. SELA was evaluated at the end of the year. The results showed a positive shift in the main constructs of self-awareness, communications, and cooperation. This was measured quantitatively and qualitatively. Conclusions were drawn and recommendations for improving the programme were proposed.

Jan 1, 2014

By Jianhong Xu, Hailong Hou, Yu Jing, Yundong Wang

Microcapsules containing extractants have been applied to the extraction of metal ions, organic acid, pesticide, and herbicide. The difficulties of conventional liquid-liquid extraction in phase mixing and phase separation (e.g. high energy consumption, emulsification phenomenon, and large equipment requiring housing) could be overcome in a liquid-solid system by using microcapsules. Even some extractants with high viscosity and poison can be encapsulated conveniently into microcapsules. In the work described in this paper, polysulfone microcapsules containing 2-ethylhexylphosphonic acid mono-2-ethylhexyl ester (P507) were successfully prepared. Then, the extraction rate of lanthanum, samarium, and erbium in dilute solution into the microcapsules containing P507 was studied. An extraction kinetic model is proposed based on the interfacial reaction model accompanied by intraparticle diffusion expressed by Fick’s law. The extraction efficiency was obtained by using the kinetic model with the separately determined complex formation rate constant and the intraparticle diffusion coefficient. From the results, it was confirmed that the kinetic model could predict the experiment in a microcapsule system over a wide concentration range of lanthanide solution. In the future, the model could provide good guidance for the design and application in extraction of lanthanides.

Jan 1, 2014

By Y. L. Tian

Low-grade bauxite with A/S of 4.4 from Henan province was used as raw material and the selec-tive grinding of bauxite, grinding efficiency, particle size and Al2O3 and SiO2distributions of ground products were investigated using ball and vibration mills. The results show that the selective grinding can be used to realize the separation of aluminum from silicon within a certain particle size. The optimal grinding conditions of the ball mill with bauxite are as follows: grinding material to charge ratio, 1.2, charge volume ratio, 40%, pulp con-centration, 70wt%, medium size distribution, F30mm:F20mm:F15mm=20%:50%:30%. Under the conditions, the weight rate of ground product with A/S over 7.5 is 27% and the recovery of Al 2O3is 30%. The optimal grinding condition of the vibration mill with bauxite are as follows: grinding material to charge ratio, 0.9; charge volume ratio, 70%; concentration, 70%; medium size distribution, F40mm:F30mm:F20mm=20%:30%:50%. Under the conditions, the weight ratio of ground product with A/S over 7.5 is 25% and the recovery of Al 2O3is 27%. The research is significant for the rational and economical utilization of the low-grade bauxite.

Jan 1, 2014