Search Documents

By T Higuchi, T Yamamoto, K Takehara

Iron ore fines are used as raw materials for sintered ore for blast furnaces in the world. Since the production and quality of sintered ore have a great influence on the stable operation of a blast furnace, many technologies were developed for controlling the heat profile in the sintering machine, which largely affect the sintered ore properties. In particular, the influence of oxygen in the suction gas, which plays an important role in combustion, was investigated over the years. It is known that increasing the oxygen ratio by about 30 per cent not only significantly improves the combustion rate, but it also increases the strength and yield of sintered ore. However, the details of the mechanism for improving these qualities are unknown. In this study, we investigated the influence of oxygen enrichment at higher ratios (O2: 21–40 per cent) and tried to understand the sintering behaviour enhanced by oxygen. The effect of oxygen enrichment on sintered ore quality and the heat profile were evaluated by sintering tests using a quartz glass pot. From the results, sintered ore yield had a maximum value for O2 = 30 per cent, but strength was increased for O2 = 40 per cent. From heat pattern analysis, it is clear that the high temperature holding time also reached a maximum at O2 = 30 per cent. Furthermore, we found that with increased oxygen ratio, the combustion speed (flame front speed) was increased, but the area of combustion was enlarged. It is considered that there could be a maximum oxygen ratio value for the yield from the balance of these positive and negative effects on high temperature holding time. To clarify the reason for strength improvement, thermodynamic calculations were performed and it was found that melting behaviour could be improved by changing the oxygen ratio.

Sep 18, 2023

By J Holdsworth, L Sutton, A Lavrinec, D Ilic

Air quality is a big topic of discussion in regional mining communities as well as urban environments situated close to port terminals handling bulk solids. Community perception of poor air quality can significantly affect the reputation of the mining operation and handling facilities. Dust monitoring for regulatory compliance relies on using a handful of accurate but very expensive sensors, usually situated at the boundary, relatively far from the activities that generate the airborne dust. These reference monitors measure dust leaving the site but dust mitigation and management on-site largely relies on operator judgement. At a fraction of the cost, small wireless solar powered units can be used to supplement reference monitors in real-time. Due to their compact nature, portability and low price, these units can be implemented on a mass scale to increase spatial resolution of dust measurements and, more importantly, in much closer proximity to both the dust generating activity and the sources of dust. This can provide valuable insights into the origins and timing of dust generation thus producing datadriven decision-making while minimising subjectivity. Similarly, light detection and ranging (LiDAR) is another supplemental technology that can be used to increase the spatial resolution of dust measurements in near real-time, however, the cost of commercial systems even exceeds that of regulatory monitors. LiDAR also presents difficulties in quantifying dust plume concentrations. This study presents learnings of implementing both technologies for dust emissions management. Several low-cost sensor units and a fast-scanning custom-built 3D LiDAR system operating at a range of 1.5 km with a resolution of 1.5 m were deployed on a surface mine to monitor dust emissions from different activities. The project explores the use of real-time sensor data to quantify LiDAR measurements in parallel with integration into mine planning. The approach can assist in prioritising dust mitigation activities thereby reducing instances of emissions exceedance and minimising water use through databased and targeted application. Demonstrated is an opportunity for a step-change in industry best practice as well as commercialisation and operationalisation of the method across different industries, including future mineral extraction.

Sep 18, 2023

By G P. S Resende, D E. G Oliveira, E A. S Baeta, T F. Bravin

There is currently in the mining industry, as well as in other industries, a movement seeking to increase investments in decarbonisation processes to help combat global warming. Among some initiatives taken is replacing diesel-powered mobile equipment in the mines with electricity-powered equipment, such as electric off-highway trucks or even belt conveyors in the mining operation. Samarco is a Brazilian mining company that since its conception has used a conveyor belt mining system in its mining operation, using only a small number of trucks to complement the mining process. This mining process that combines conveyor belts and trucks has brought environmental gains for the company since the environmental impact of conventional truck-only mining is greater than that of the combined system. To measure these gains, a medium-term mining plan was developed in which two fleet scenarios were detailed. One scenario contemplated a high level of detail of belt mining seeking its maximisation, while the other considered the operation performed 100 per cent by trucks, eliminating the use of conveyor belts. Through the comparison of these two scenarios, it was possible to make an inventory of atmospheric emissions and greenhouse gases for each one of them considering data such as types of equipment, diesel consumption, total distance travelled and energy consumption. The results showed that the fleet scenario with conveyor belts results in periods with up to 15 per cent less greenhouse gas emissions and 37 per cent less total particulates compared with the truck-only scenario. Therefore, the results confirm the environmental benefits of the method and the need to look for ways to even expand it in future operations through a study to identify the potential areas in the long-term mining plan.

Sep 18, 2023

By C R. Ure

To substantially reduce, if not eliminate, carbon dioxide (CO₂) emissions from ironmaking it is necessary to convert from blast furnace (BF) ironmaking using coking coal as the reductant to direct reduction (DR) ironmaking using hydrogen (H₂) and green electricity. Currently, almost all natural gas (NG) based direct reduced iron (DRI) production utilises iron oxide pellets in shaft furnaces, as opposed to fines in fluidised beds. Also, these pellets are ordinarily produced from high-grade magnetite concentrate, rather than hematite and goethite with typically higher gangue contents. The use of high-grade magnetite concentrate is driven by the preference to melt DRI in conventional electric arc furnaces (EAFs), thereby avoiding the basic oxygen furnace (BOF) for making crude steel (CS). However, in replacing BF with DR ironmaking it is not economically feasible to source enough high-grade magnetite to replace the lower grade hematite and goethite currently consumed. That is not to say that hematite and goethite, or even low-grade magnetite, cannot be used in DR ironmaking. However, their higher gangue content, resulting in higher slag production, requires that the EAF producing CS be replaced with a submerged arc furnace (SAF) that will produce pig iron (PI) for the BOF as does the BF. Here, critical issues to be addressed are, what are the technicalities in replacing high-grade magnetite concentrate with hematite and goethite and NG with H₂ in DRI pellet production and melting? This paper summarises certain relevant published information on DRI pellet research, test work and production together with relevant information on Pilbara ores. It attempts to illustrate the inter- relationship of composition and processing conditions on DRI pellet properties. It is intended to serve as a rudimentary guide to understanding the complexities of formulation, testing, evaluation, production and goethite and offer insight into this challenge.

Sep 18, 2023

By O A. Aladejebi, S Mitra, T Singh, D O’Dea, S, T Honey

Granulation of the iron ore blend and the additives is the foremost step in the agglomeration of iron ore fines to achieve a permeable bed during sintering, which is crucial for sinter productivity. This study investigated the granulation of four types of blends to determine the impact of granulation on bed permeability. The blends were granulated in a rotating drum at various moisture contents and their JPU permeability was measured at each moisture content in a permeability pot (diameter 95 mm and height 500 mm) at various flow rates. Several independent experiments were carried out to investigate the changes in permeability when mixtures of different particle size range (-1 mm and +1 mm) were introduced into a packed bed with a larger particle size range (-6.3 mm to +4.0 mm). The results revealed that the addition of particles in the -1 mm size range had a more pronounced negative impact on permeability compared to particles in the +1 mm size range. This can be attributed to the relatively higher energy losses (mainly inertial) associated with the presence of -1 mm particles in the mixture. The findings were used to quantify the granulation process based on the -1 mm particle size fraction in the granulated mix and their utilisation (denoted by UI-1 mm). For achieving optimal permeability in a specific blend, it was found that a UI-1 mm (utility index of -1 mm particle size) ranging from 0.82 to 0.92 was required. However, exceeding a UI-1 mm value of 0.95 resulted in weaker granules prone to deformation and led to decreased bed permeability. The study also showed that the UI-1 mm was highly dependent on the water addition per kg of -1 mm in dry feed and suggested adding ~80 to 110 mL of water per kg of -1 mm in dry feed to attain the best possible permeability. Additionally, the research proposed a mechanism involving the melting of granules at high temperatures and highlighted the influence of -1 mm particles on bed permeability during the sintering process.

Sep 18, 2023

By M I. Pownceby, M A. Rhamdhani, W J. Rankin, G Brooks, I R. Ignacio

Steelmaking has a significant contribution in producing greenhouse gases and there is a worldwide push towards decarbonising the process. One of the approaches to reduce CO2 emissions is to use hydrogen in the blast furnace (BF) as the reductant gas. However, hydrogen reduction is an endothermic reaction, bringing changes to the temperature distribution in the BF. Understanding iron ore sinter mineralogy and reducibility under a hydrogen atmosphere is essential to optimise the process. In this study, sinter analogues in the Fe3O4-CaO-SiO2 (FCS) ternary system together with industrial sinters were reduced in H2-rich and CO atmospheres and the resulting reducibility and associated mineralogical changes were observed. Results show that magnetite-lime-silica (MLS) sinter analogues had similar reduction rates under H2 and CO, and also higher reducibility than most of the industrial sinters, suggesting that magnetite sinters could be used efficiently in a conventional or hydrogen blast furnace.

Sep 18, 2023

By S Hapugoda, Y Tang, L Lu

The steel industry is one of the global leading CO2 emitters, accounting for approximately 7 per cent of global anthropogenic CO2 emissions. In 2022, the world produced 1878.5 Mt of crude steel. About 70.8 per cent of the world’s crude steel was produced by integrated steel mills through the blast furnace and basic oxygen furnace (BF-BOF) process, while the remainder was produced largely by mini mills using electrical arc furnaces (EAF). Compared with gas-based DRI and scrap-based EAF processes, the direct CO2 emissions from the BF-BOF process and the coal based DRI and EAF process are significantly more, as both the processes rely heavily on fossil fuels, such as coke and pulverised coal, to provide energy and reduce iron oxides. Hydrogen is very reactive and reduces iron oxides to metallic iron without generating CO2. Therefore, substitution of hydrogen for fossil fuels in these processes presents a good opportunity to significantly decarbonise the steel industry. This paper will first discuss the thermodynamic and kinetic characteristics of hydrogen and carbothermic reductions of iron oxides and then examine the behaviours of different ore types present in Australia iron ores during hydrogen reduction.

Sep 18, 2023

By N Maistry, A Singh

It is estimated that in less than a decade, high-grade iron ore reserves in South Africa will be depleted, leaving only low-grade ores with a dominant lithology of banded iron formation (BIF) hematite. BIF is a complex ore reserve as it is typically liberated below 1 mm, resulting in high energy costs. However, due to its abundance, its beneficiation potential should be evaluated to maximise recovery at an acceptable product grade. To develop a beneficiation program for BIF hematite, the first step is to determine the effect of two laboratory crushing techniques on mineralogical characteristics, specifically liberation and shape. For this study, the cone crusher and high pressure grinding rolls (HPGR) were used. The Electron MicroProbe Analysis (EMPA) and Mineral Liberation Analyser (MLA) were used to compare the mineralogical characteristics. The liberation characteristics for hematite are similar for both crushing techniques; however, HPGR preferentially liberates quartz. HPGR achieved 8– 12 per cent additional quartz liberation in the greater than 80 per cent and 100 per cent liberation classes respectively and specifically in +75 μm size range. Improved quartz liberation is associated with lower energy requirements for downstream milling and improved separation efficiencies for beneficiation units that operate in this size range. Both samples displayed similar shape characteristics; most particles were elongated smooth and the rest were elongated angular. Good hematite liberation is expected at grinds of 212 μm to 150 μm. Further consideration should be given to throughputs, energy efficiency and downstream equipment selection prior to selecting a crushing technique.

Sep 18, 2023

By J Carter, B J. Armstrong

Best practice for the submission of samples to an internal or commercial laboratory requires quality control materials to be included for the purpose of independently and comprehensively assessing laboratory performance. These quality controls include the use of certified reference materials (CRMs) and may be blind to the laboratory. Iron ore companies purchase these materials from reputable manufacturers from stock of run-of-mine materials at the appropriate grades. The international standard, ISO 17034 (ISO, 2016), specifies the competency requirements for organisations manufacturing reference materials, and includes rigorous requirements for the assessment of homogeneity, stability and establishment of property values and their uncertainties. Homogeneity is one of the most important measures of suitability for all certified reference materials and refers to the degree to which the composition and properties of a sample are uniform throughout the batch, relative to the analytical precision of the method. More specifically, homogeneity studies of candidate reference materials should be assessed for both within sample variance and between sample variance with appropriate statistical controls. The design and application of homogeneity studies are discussed as they apply to both crushed and pulverised reference materials. Crushed certified reference materials have been utilised by the iron ore industry for a number of years and provide the user with a critical assessment of variances in sample preparation in addition to analysis. Crushed reference materials are similar in presentation to an RC sample and are generally used as discrete parcels of material submitted to the laboratory from the field. Pulverise certified reference materials miss the sample preparation step and are subsampled from th delivered sachet at the point of analysis. This paper compares the relative homogeneity performance of crushed and pulverised certified reference materials by grade across key iron ore chemical constituents. Outcomes are benchmarked to the international standard ISO 9516 (ISO, 2003) for the determination of various elements in iron ores by lithium borate fusion and X-ray fluorescence. Practical implications are discussed with reference to a case study from an iron ore laboratory in the Pilbara.

Sep 18, 2023

By M Pomery

BHP’s Western Australian Iron Ore Operations (WAIO) move approximately 250 million tons of ore per annum. The magnitude of the constant changes to the terrain models along with the diverse output and presentation requirements of numerous stakeholders presents significant challenges for the geospatial team. This paper describes how the WAIO Survey team use a combination of technology and optimised workflows to capture, ingest, publish and access large data sets for diverse stakeholder requirements. Machine learning for processing of data and the use of web based systems to track and prioritise task allocation of resources will be discussed in detail, in addition to the changes to the traditional roles of surveyors from the use of automation and mobile technology.

Sep 18, 2023

By S Mitra, D O’Dea, N Barrett, S, T Honey, M M. Hoque

The steel industry is currently exploring hydrogen-enriched blast furnace operations as a means to reduce the greenhouse gas emissions. However, there is a need to investigate the gas permeability behaviour of mixed burdens comprising of lump and sinter as the current knowledge regarding their behaviour is limited, particularly with regards to hydrogen enrichment. In the present study, a series of interrupted softening and melting (S&M) under load tests were carried out in a hydrogen rich gas environment (~15 per cent) in the temperature range from 1000 to 1300°C by placing different types of ferrous ore layer including Newman Blend Lump (NBLL), sinter and sinter-NBLL mixed burden in between two coke layers. X-ray computed tomography (CT) was then used to scan the interrupted test samples. Scanned images were first analysed using an image processing workflow implemented in ImageJ and the material simulator GeoDict (v2022) to segment different phases such as coke, ferrous and void based on their grey scale values. A quantitative analysis was then performed on the segmented images to estimate the phase volume fraction as well as bed permeability. Bed void fraction thus obtained agreed well with the bed contraction data obtained from the S&M test. It was further noted that both ferrous layer void fraction and bed permeability decreased linearly with increasing temperature for all ore samples. The mixed burden voidage changed in a similar fashion to the sinter, demonstrating a high temperature interaction between the two materials

Sep 18, 2023

By A Tolley

Bauxite residue or ‘red mud’ is a by-product of the Bayer Process, the primary process of alumina refining. Due to its high alkalinity and variable composition, its storage and disposal poses high environmental risks to water sources, surrounding ecosystems and human health. The high alkalinity (pH 12–13) is a significant factor in its classification as hazardous waste; to mitigate this, Australian refineries have integrated neutralisation processes into bauxite refining. Both sea water and carbon dioxide neutralisation processes are applicable. Multiple studies have demonstrated pH reduction from 12–13 to 7–10, depending on the method. The key advantages of CO2 neutralisation are that it allows for carbon sequestration and is more effective when utilised as a pre-treatment for recovery of metals, while sea water neutralisation is more established and has been integrated into two Australian refineries. This paper proposes the application of the bacteria Exiguobacterium oxidotolerans for bioleaching of iron from hematite in bauxite residue. The genus Exiguobacterium is characterised by its high levels of adaptability, halotolerance and alkaliphilic nature. E. oxidotolerans is successful at eluting Fe2+ from hematite via reductive dissolution, which complexes with oxalic acid produced during metabolism. This aquatic bacterium presents a novel process pathway for iron elution due to direct interaction of E. oxidotolerans with hematite via the cell membrane and operates within the pH range of neutralised red mud. The proposed mechanism is extracellular electron transfer, a microbial metabolic process where electron transfer is facilitated between bacterial cells and extracellular material. Currently this is being investigated for promotion of seaweed growth in coastal environments as soluble iron aids and fortifies colonies. This has potential downstream applications for cleaner iron and steel production. While theoretical, this paper explores the neutralisation, bioleaching and application of the Fe(II)- and Fe(III)-oxalate complexes formed.

Sep 18, 2023

By M I. Pownceby, A Guiraud, S Purohit

Sticking and breakage of iron ore pellets during high temperature reduction can result in several operational challenges during shaft furnace ironmaking. With the shift to H2-based DRI processes and decreasing iron ore quality, this issue becomes more prominent. It is therefore important to understand how the iron ore chemistry and mineralogy affects the sticking and breakage of pellets inside the shaft furnace. This study provides a review of the mechanisms that lead to sticking and breakage of pellets inside the shaft furnace. The sticking index of pellets is related to the rate of metallic iron production as well as the precipitation morphology of product iron. Sticking of pellets is also enhanced by the formation of low-melting slag phases. The breakage of pellets inside the shaft furnace is often associated with the mechanical load of burden and pellet swelling, which is caused due to iron whisker or protruded iron formation. This paper investigates how the composition of iron ore, particularly the presence of different impurity oxides such as SiO2, Al2O3, MgO, CaO and alkali oxides in the pellets, influences the sticking and swelling indices. The effect of ore mineralogy on these adverse behaviours is also discussed.

Sep 18, 2023

By X Yu, Y Shen

The iron ore products should be assessed in terms of in-furnace behaviour and overall furnace performance, their operation should also be optimised under industry-scale blast furnace (BF) conditions, in order to be sustainable and competitive, especially in the context of decarbonisation efforts in ironmaking. While lab and pilot-scale experiments can provide useful kinetics, they are expensive and risky and cannot replicate industry-scale blast furnace conditions for proper assessment and optimisation. In this paper, we review our recent progress at Shen Lab of UNSW in using state-of-the-art Computational Fluid Dynamics (CFD) models to assess iron ore products and examine the effects of their operations on BF behaviour in basic terms, including in-furnace phenomena (flow field, temperature field, species distribution fields etc) and overall BF performance (coke rate, reduction efficiency and top gas temperature etc). We have developed state-of-the-edge CFD models for different purposes, ranging from the static-state BF model featuring unique layered burden structures for offline assessment and optimisation knowledge building-up for iron ore products, to the transient-state BF model for online assessment and optimisation of iron ore productions by describing the transient behaviours of iron ore productions under industry-scale conditions. First, we have studied several iron ore products including the iron ore products used in the present BFs and emerging iron ore products like carbon composite briquette and iron-coke. Second, several iron ore operations are studied including optimisation of conventional burden operations like oxygen enrichment, batch weight tuning and new operations like coke central charging and hydrogen injection in BFs. Third, some time-sensitive operations are also investigated including the use of wet burden materials and the drop in blast temperature on BF performance. These CFD models offer cost-effective research tools for understanding the effect of iron ore products on BF performance and serve as a reliable marketing tool for existing and emerging iron ore products under a wide range of BF conditions.

Sep 18, 2023

By H Arvidson, B Spence, S Helm

Mining is the art of disturbing ground. All phases of a mine’s life cycle from exploration to building and operating a mine, through closure, has a physical impact on the earth. There is currently increasing public and stakeholder awareness owing to a wide range of issues including heritage protection, environmental stewardship, and social impacts therefore ground disturbance must be conducted in a way that honours and respects all agreements, regulations, legislation, and social expectations. A comprehensive ground disturbance permitting process has been developed through consultation with major mining companies and Traditional Owner groups. It operates from strategic business planning through to closure and rehabilitation. Adherence to the principles and process of permitting helps to minimise risk by ensuring that mining companies conduct their business in an inclusive, professional, reliable, and consistent manner that stakeholders reasonably expect, and that mining companies can be proud of. Built on a geographical information system, supplemented with a specialist database, this process allows request, review, and approval by subject matter experts, to operate in a common environment that is transparent, facilitates collaboration, improves efficiencies, and reduces the risk of error or omission. The application of new technology can effectively highlight changes that naturally occur in today’s dynamic ESG domain and provides the perfect platform to record actual disturbance against authorised and planned allowances. The social license to operate demands that strong governance of the ground disturbance process, described herein, can be demonstrated to any interested stakeholder, and mining companies recognise that this principle is central to the betterment of the mining industry.

Sep 18, 2023

By C T. Portelli

Belt conveyor transfers are the most likely location for high wear rates and failures. Belt transfers are necessary to change the direction of conveyed material and will remain a part of belt conveyor systems into the future. Burden being accelerated due to fall and changes in direction from one system to the next, prevents steady state flow which introduces component fatigue. The conveyor belt is considered the greatest cost item over the life of a belt conveyor system and consumes considerable downtime to replace, therefore a financial incentive exists to preserve this high-cost item. Other issues created at the transfer include health risks of uncontained dust and product losses due to spillage. Additional consideration to support the belt is one way to improve the life of components and contain dust within the transfer chute. The humble impact cradle/bed has changed little over the years whilst conveyor systems have achieved ever greater flow rates. Further development of the impact cradle is an opportunity to reduce maintenance costs and increase uptime. The peak technology on the market for conventional impact belt support is the dynamic impact cradle, which ensures the belt support area under the chute allows for some dynamic travel, whilst also maintaining a consistent skirt board area. The impact energy at a transfer when installed with Kinder Australia’s dynamic impact belt support system was measured to further understand the forces involved and how they compare with static belt support systems. Adding further dynamic capacity to the load zone has been shown to increase belt life by at least 30 per cent. Other components also benefit from reducing impact energy in the transfer and the incorporation of polyurethane bushes at roller supports has been employed further increase roller and frame life. Kinder Australia has developed a unique and innovative range of belt support technologies that further promote dynamic travel whilst maintaining a consistent skirt board area without a significant increase in belt-friction tension. This technology combines slider rails with rollers that can absorb impact independently within the support system and/or utilising exotic slider materials to overcome high belt speeds and/or system capacities. Kinder Australia has a vast library of documented case studies and application data to ensure the future systems being offered will survive, provide better chute sealing and protect the conveyor belt.

Sep 18, 2023

By R Belissont, C Veloso, L Senez, F Vasconcelos, E Kleiderer, J Mesquita, Y Basselin

Mont-Wright mining complex is an important asset of ArcelorMittal located in the province of Quebec, Canada. It is composed by Mont-Wright and Fire Lake mines, operating 365 days per annum, and producing 25 Mtpa of iron ore concentrate with 66 per cent Fe. Mont-Wright concentration plant is composed by seven lines with a flow sheet encompassing AG/SAG milling, primary and secondary classification stages, spiral concentrators (rougher, cleaner and recleaner stages) and dewatering unit operations. In this context, an equation called ‘Wrec’ was developed in 1971 with the objective of estimating the mass recovery of the different blocks in the beneficiation plant and support the mining planning works of Mont-Wright complex. This equation was based on the correlation between the results of heavy liquid tests performed with drill core samples and spiral concentrators pilot scale tests, returning an estimative of concentrator yield. However, since its first development, no updates have been done in the equation, which lead to some deviations from expected recoveries in the last years. This is probably due to the changes in the process and in the ore fed into the concentrator during the period. In this way, the study presented here corresponds to the execution of heavy liquid/spirals pilot scale tests with 26 composite samples collected at Mont-Wright deposit aiming at revising and updating ‘Wrec’ equation. Based on test work results, an updated formula was established to estimate the plant recovery and a comparison performed using industrial data showed that the old formula overestimated the real yield by 5.40 per cent, on average. At the end of the study the new equation was incorporated into the mining planning process.

Sep 18, 2023

By G S. Beros, K M. Edwards

Over the past 20 years drum scrubbers have become a widely adopted technology within iron ore beneficiation plants. Generally, the drum scrubbers in use are considered high-capacity machines capable of accepting larger-sized feed material. Together with a water addition to a desired pulp density and a mild energy input, these large rotating machines effect an attritioning action that removes water soluble clays and other deleterious materials. Within the Western Australian iron ore industry, drum scrubbers have been successfully applied to Channel Iron, Marra Mamba, Bedded and Detrital orebodies. The introduction of drum scrubbers has enabled Western Australian producers to satisfy the substantial increase in demand for iron ore from Chinese steelmakers by making the lower-grade sections of the above orebodies economic. However, despite being a relatively simple unit process, the requirements for successful design and operation of these machines are not fully understood. This paper draws on the collective experience of both authors to provide some points to consider for incorporating drum scrubbers into iron ore beneficiation plant flow sheets.

Sep 18, 2023

By J Pan, C M. Tang, D Q. Zhu, C C. Yang, S W. Li, Z Q. Guo

The short process of electric furnace steelmaking with direct reduction iron (DRI) as raw material is an important process for smelting high-quality and special steels. In order to prepare high-quality DRI, the pellets with basicity of natural basicity and 0.4 were prepared from magnetite concentrate (MR=0.09, MR=0.4) and hematite concentrate (HR=0.02, HR=0.4). Based on the HYL method, the gas-based direct reduction experiments were conducted under the condition of rich hydrogen (H2/CO = 2.6). The reduction index (RI), reduction swelling (RSI), cold compressive strength (CCS), and phase changes of the pellets were systematically studied. The results show that the RI of four kinds of pellets is greater than four in the temperature range of 800~950°C. For the magnetite pellets, at a fixed reduction temperature, the RSI increases and then gradually decreases, reaching a peak between 50 per cent and 80 per cent. Moreover, the RSI enhances with the increase of the reduction temperature. In general, the RI, RSI, and reduced CCS of the MR=0.09 pellets are better than those of the MR=0.4 pellets. For the hematite pellets, the maximum RSI decreases from 23 per cent to 17 per cent during hydrogen-rich reduction, while the compressive strength increases from 500 to 1070 Nꞏpellet-1. The main reason is that the glass phase generated by the increase of basicity adheres to the surface of hematite grains, hindering the contact between reducing gas and particles. As a result, the apparent activation energy is reduced, which is not conducive to the reduction process. In addition, the glassy phase attached to the hematite reduces the migration rate of Fe2+/Fe3+, resulting in a difference in the reduction expansion rate of hematite in the inner and outer layers of the pellet. Thus, concentric cracks are formed inside the pellets, the RSI increases and reduced CCS decreases.

Sep 18, 2023

By F van de Venter, J Monama, T Kale

For a multitude of years fine iron ore, -1 mm, across the world has been deposited as discard material in tailings facilities. This contributes to environmental problems, decreases plant yield and increases the cost of processing. Fine iron ore recovery processes are often deemed unfeasible or uneconomical, due to the complexity of the reclamation thereof in comparison with high-grade ores. However, recent advances in the recovery of fine iron ore using the Optima Classifier® has shown great promise. The Optima Classifier® is a new hindered settling separator that makes use of an upward current of water for density separation. It’s unique design combines three different separating zones for increased efficiency and recovery. In this study the potential of the Optima Classifier® to produce a +63 per cent Fe concentrate from -1 mm feed material was evaluated from a standalone and process perspective. It was found that a +63 per cent Fe product can be produced from a single stage, using the Optima Classifier®. Fine iron ore feed with an average head grade of 50 per cent Fe was upgraded to average concentrate grades of 63.2 per cent Fe. Displaying upgrade ratios of up to 1.26 in a single stage. A three-stage, rougher, cleaner and scavenger system did however show the best performance with recoveries of up to 70 per cent, yielding 56 per cent of a 63 per cent Fe product. Furthermore, the dewatering of the product and tailings was evaluated using the UltraG ultra-fine dewatering screen ensuring dry, stackable material. The tailings could be used in codisposal, while loads on thickeners and filter presses are significantly reduced. The high throughput of the Optima Classifier® ensures a small plant footprint, minimal civil and structural requirements and low operating utility consumption such as electricity, minimising the carbon footprint of a fines beneficiation plant. The Optima Classifier® in combination with the UltraG dewatering technology has provided a platform for economical recovery of fine iron ore, both current arising and historical. Providing opportunity to lower plant operating costs, reduce environmental liability of tailings facilities and increasing immediate process water recovery

Sep 18, 2023