Search Documents

During the lifetime of an open pit mining project, each stage from exploration activities to exploitation and mine closure produces disturbances on the mining region. Mined land reclamation plans establish constructive solutions to rehabilitate the disturbed areas. Open pit mining as an effective method for exploitation of a wide range of orebodies especially for massive reserves of shallow metallic substances has exhaustive and harmful environmental effects on the mining project region. Nowadays, closure and reclamation stage in a mining project is emphatically enforced by the relevant environmental protection regulations in many countries. It is therefore obvious that closure and reclamation costs of an open pit mining project, as costs of other stages of project, must be estimated to enter the planning and design processes in open pit mining. Post-mining land use is the most important factor to recognise closure and reclamation costs. Thus, using a model to define optimal land use in planning phase of an open pit mining project is necessary in this regard. In this project a model was developed to define optimal land use regarding different sections of open pit mines such as pit(s), waste dump(s), tailing pond(s), roads, areas for onsite facilities and free land zones which are not mined. TOPSIS and PROMETHE techniques were applied to create the developed model. Lumber production was recognised as the optimal post-mining land use for the pit area of the case study in this project.

Dec 6, 2010

The design of a mine should aim to optimise the market value by maximising revenues whilst minimising costs. In open pit mining, the nature of the extraction technique translates this objective into the maximum recovery of reserves while minimising waste extraction subject to technical, economical and safety constraints. Since the introduction by Lerchs and Grossman, in 1965, of a model that is now considered a classic in the area, open pit design has reached a level of maturity and acceptance by industry. These models are being used on a regular basis by designers and planners.This paper proposes a new alternative model for open pit design. It is based on genetic algorithms (GA) and exploits a reduction of the number of decision variables of the more traditional techniques. The novel approach provides more flexibility than traditional models; it can also be extended to consider planning problems that traditional open pit design models are not capable of handling. The algorithm has been designed for two dimensional problems and tested in a simple instance. The results obtained in this simple test are encouraging and are a good supporting argument for the development of a GA model capable of handling three-dimensional (3D) instances. The model presented in this paper is just a first step towards a full GA to solve the pit design problem and it is believed that novel tools like the one presented herein could become great allies in tackling challenging problems in open pit design, an illustration of such a challenging problem is presented and discussed.

Dec 6, 2010

Development of aggregate resources for use in structural concrete has been encouraged in Japan to support infrastructure improvement and national land conservation. Natural aggregate is a valuable resource necessary for sound economic development, and its importance is growing. After completion of aggregate mining projects, planting and afforestation are implemented. But sandy soil in excavation sites is not optimum for the growth of vegetation, and many years are needed before forests are restored. Planting techniques should be improved to support efficient reforestation in a shorter period of time. For this purpose, problems hampering growth of vegetation must to be solved through application of physical and physicochemical techniques to ensure that the environment and the ecosystem will be conserved in project sites.

Dec 6, 2010

In responding to why some longwall roadway development rates are different among mines, the Roadway Development Task Group (RDTG) of Australian Coal Association Research Program (ACARP) has initiated a benchmarking study to survey each longwall mine to determine the correlation between roadway development practices and roadway development performances. This paper describes a web-based relational database system which has been developed purposely to monitor the performance of Australian longwall roadway developments aimed at assessing both the physical and operational factors which could influence roadway development practices and their performance indicators. Statistical analysis of an earlier survey suggested that continuous miner units that achieved more than 1750 m were units mining two-heading development.

Dec 6, 2010

One of the important directions of further increase of quality and efficiency of control of mining companies and branches is the creation of the operation and development monitoring systems of such facilities. The main purpose of these systems is to provide managers with reliable and timely information on the current state and typical tendencies of operation of the facilities under control. However until the present time no scientific and methodical ground for system monitoring of the mining companies and branches has been created. Therefore, the authors of the report have aimed to assess the current situation with regard to the researches in this field and to do analysis of the most important aspects and ways of solution of the issue under consideration.

Dec 6, 2010

Precision surface mining is increasingly occupying a significant role in open pit mining. Improvements in technology now allow continuous surface mining of material well above 140 MPa (20 300 psi) efficiently and cost effectively when compared to drilling and blasting/primary crushing methods. These include the elimination of the use explosives and primary crushing, the ability to precisely extract the ore from the waste, or separate ores of varying chemistry and mine thin seams and non-homogenous orebodies cost effectively. In addition, precision surface mining extends the useful life of a mine by extending the mine boundaries. It can expand production capacity in existing mines and is particularly cost effective in greenfield start-up mines. Precision mining techniques result in higher percentage recoveries. This paper reviews several of these techniques for the Terrain Leveler« surface excavation machine (SEM), and shows their impact. Vermeer's current approach to precision surface mining is utilisation of the T1255 Terrain Leveler SEM. Several units have been proven in round-the-clock, seven day operations throughout the world. Among other innovations are design simplicity, stability, maneuverability, rear-mounted tilting drum and top-down cutting. The impact of these items are discussed in more detail in the paper. After a detailed analysis of the importance of machine availability on overall mine performance, Vermeer has extended its equipment line to include a direct-drive option for its T1255 Terrain Leveler SEM. In addition, improvements in dust suppression are presented. While the T1255 Terrain Leveler SEM is of optimum size and cost in small and medium sized mines, Vermeer has recognised that larger mines require larger machines with increased capacities. Vermeer will prototype the T1655 Terrain Leveler SEM later this year. Specifications of this machine and up-to-date preliminary results are presented. A discussion of the role of each machine size and driving mechanisms are included. Finally, the next stage in Vermeer's providing solutions to the surface mining community will be described - a continuous loader. The impact on current mine planning is presented using a detailed computer program developed for studying the impact of loading techniques and higher production rates on mine plan optimisation.

Dec 6, 2010

By N S Melkoumian

While improvements in occupational health and safety (OHS) in the mining industry have decreased fatalities and accidents, little attention has been paid to the cultural confound of 'safety' in the increasingly multicultural mining industry. Occupational health and safety processes often contain assumptions of cultural understanding that may not be shared or understood by mining employees. There are potentially dangerous and costly implications of cultural difference in the mining environment. Some people have been enculturated with high levels of anxiety concerning catastrophe and uncertainty while others have a more laissez faire attitude to accidents and disaster. The level of cultural anxiety about uncertainty can be a major factor in the acceptance of OHS processes. OHS manuals based on a comprehensive set of rules and procedures may assume that the authority of 'rules' is shared by all employees regardless of a variety of cultural understandings when this may not be the case. Similarly, cross-cultural employees may not share a background or acceptance of expensive technological innovation and so resist/avoid the application of new safety equipment. Then too, OHS staff may not realise the significance of religious belief or personal responsibility on employees' attitudes to safety in the workplace environment. A lack of consideration of these cultural elements could have fatal and expensive results. This paper explores the impact of cultural difference in the understanding of OHS in the Mining Industry, presents a model to improve the understanding of the cultural confound in safety, improves analysis of OHS in practical multicultural situations, provides assistance for those involved in OHS training and may become a basis for developing OHS policy and procedure.

Dec 6, 2010

By Bradford F. Townsend, Matthew E. Fowler, Michael F. Smithson, Lawrence R. Eckert

All Rights Reserved. Printed in the United States of America. Information contained in this work has been obtained by SME, Inc. from sources believed to be reliable. However, neither SME nor its authors guarantee the accuracy or completeness of any information published herein, and neither SME nor its authors shall be responsible for any errors, omissions, or damages arising out of use of this information. This work is published with the understanding that SME and its authors are supplying information but are not attempting to render engineering or other professional services. If such services are required, the assistance of an appropriate professional should be sought. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of the publisher. Any statement or views presented here are those of the authors and are not necessarily those of SME. The mention of trade names for commercial products does not imply the approval or endorsement of SME.

Dec 1, 2010

It's long been suspected that there has been an increase in the incidence of premature failure of rock bolts in underground coal mines over the past ten years. As far back as 2002 a study found a possible contributor to such premature failure in some Australian coal mines might be linked to stress corrosion cracking (SCC) (Crosky et al, 2002). That study suggested the low impact toughness could be a major influence on the susceptibility to SCC of different steel compositions. A subsequent study involving laboratory corrosion tests however failed to confirm any link with metallurgical factors (Villalba and Atrens, 2007), a finding that is at odds with field experience. Some mine sites today are still reporting prematurely failed rock bolts to the rock bolt manufacturers; the failures are being identified at SCC induced. To this end a research project has recently been commissioned at University of New South Wales (UNSW), which aims to identify the environmental factors causing SCC, through field test sites and simulating the conditions within an accelerated corrosion laboratory. This paper outlines the methodology that will be used in this study.

Nov 25, 2010

The Australian mining industry faces skills shortages across a broad spectrum of disciplines and levels, as it enters another major growth phase. Critical amongst the areas of most significant shortage in the professional sphere is the discipline of geotechnical professionals. More mines, deeper mines, ageing workforces are all contributing to this chronic shortage. But the shortage is not just at the operating sites, it is across a range of employment fields including sites, head offices, consultants, researchers and educators. This paper reviews the status of a number of these fields and explores some of the issues being faced. The different roles of a site geotechnical professional and a specialist geotechnical consultant are explored, together with some of the trends in terms of how such people are operating, and the skills they are expected to have to fulfill their job requirements. The paper also considers the move towards possible mandatory statutory geotechnical positions at mine sites and some of the implications if this were to come into force. Finally, the paper considers the current provider programs for mining geotechnical education, and how additional offerings are going to be needed in order to address the current shortages and the inconsistencies in terms of job expectations for people assigned to geotechnical roles without adequate education and training.

Nov 25, 2010

The case study has identified and characterised additional subsidence arising from longwall mining above or under existing longwall goaf. It suggests that the magnitude, mechanisms and prediction methods for such additional subsidence are different between the two mining configurations. This paper presents a proposed method to predict maximum vertical subsidence due to longwall mining under existing longwall goaf. It suggests that, unless different results from further new cases become available, the findings presented in this article, including the aforementioned prediction method, be applicable to the majority of sites in New South Wales, where multi-seam longwall mining is to take place. This article also presents an important concept of 'overburden modification' due to multi-seam mining. A causal relationship between the above-mentioned additional subsidence and 'overburden modification' has been identified as a result of the case studies. Further investigations into the physical processes that cause such overburden modification will be fundamental to the understanding and management of multi-seam subsidence.

Nov 25, 2010

The transition from low stress to high stress conditions is a challenge eventually faced by most mines in Australia that extend to depths greater than (generally) about 1000 m. In areas with strongly adverse 'stress versus depth' gradients, such as some parts of Western Australia, significant stress-related problems have occurred at depths as shallow as 300 m below surface. The actual depth at which the 'transition' occurs is a function of the local pre-mining stress field, the strengths of the various rock types hosting the deposit and the layout and sequencing adopted in the mine. Stress-related damage can result in increased support costs, and delays associated with rehabilitation and disruption to production. In the worst case, where strong seismicity and associated damage occurs in active mining areas, 'exclusion' zones and 're-entry' protocols may be required. These can severely disrupt production. A key aspect of managing the transition is the recognition of the onset of stress-related ground behaviour. Damage mapping can be used to develop understanding of the relationships between mining activities and the local and regional response to them. Carefully documented case histories provide a basis for calibrating numerical models. This paper discusses some of the typical styles of ground behaviour observed in higher stress conditions in underground mines. A simple damage classification scheme is described to assist in 'damage mapping' of mine tunnels. An example of damage mapping is presented to illustrate an approach commonly used for recording stress-related damage.

Nov 25, 2010

Corrosion affects the performance of rock support and reinforcement at various underground mines, including the George Fisher Mine, where recent studies showed that this risk to mining operations is generally not well understood. Corrosion reduces the capacity and life expectancy of ground support and generally is undetected unless the traditional destructive pull out test is employed to detect defect bolts. Where it is still acknowledged that the pull out test has still an important role to play in determining critical bond lengths for static and quasi static ground support designs, it does not provide an underground operation with any reassurance regarding its bolt's integrity, which has been compromised by in situ aggressive conditions. Non-destructive rock reinforcement calibration testing on single and twin strand cable bolts, rebar bolts and friction bolts at the George Fisher Mine enabled the testing team to detect bolts with compromised integrity in one area of the mine. The non-destructive rock reinforcement integrity testing conducted uses a complex 'Stress Wave Analysis' package based on the processing of clear seismic signals imparted into the rock reinforcement element that is being tested. The seismic signals are processed by 'Fourier Transform' into various criteria which can be used to produce models of the element such as mechanical admittance, frequency spectra and velocity which are all being used in the final modelling of the rock reinforcement element under analysis. This paper highlights the enormous potential to effectively manage the geotechnical risk that corrosion presents for an underground mining operation.

Nov 25, 2010

Support design in jointed or blocky rock masses is often approached by the use of either 'rules of thumb', rock mass classification systems such as the Q-system (Barton, Lien and Lunde, 1974) or RMR (Bieniawski, 1973) or conventional wedge analysis. Generally, this requires that a number of key simplifying assumptions are made and the support system is designed to cater for either a mean, most likely, or worst case scenario depending on the risk tolerance. The design block size is often a major uncertainty and often a worst case block size based on excavation span is used. Thompson and Windsor (2007) state that it is inappropriate to base support designs on the excavation size as these size blocks rarely occur if discontinuity trace lengths are considered. Probabilistic keyblock methods can be used to determine the most likely design block sizes. A methodology is presented whereby JBlock software (Estherhuizen, 1996) is used to estimate potential block sizes as part of the support design process. Using information such as the spacing, orientation and length of discontinuities, it is possible to simulate blocks in the walls of an excavation (Esterhuizen and Streuders, 1998). Keyblock analysis methods (Goodman and Shi, 1985) are used to evaluate whether blocks are removable and whether the chosen support will be sufficient to ensure stability. Data from two mines is used to demonstrate how probabilistic keyblock analyses can be used in support design. Discontinuity data was used to generate 10 000 removable blocks and the design block size statistics were determined. For one mine this information was used to scale blocks in a conventional. Unwedge analysis whilst for the other mine, the point estimate method (Harr, 1987) was applied. The choice of appropriate design acceptance criteria in terms of factor of safety and probability of failure is also considered.

Nov 25, 2010

Underground excavations are subjected to complex stress changes caused by nearby mining, but may also be affected by repeated dynamic loading from blasting and seismic events. In some cases, the combined, cumulative effects can lead to unforeseen damage, displacement and instability. Simulating dynamic loading of an underground excavation is a very complex task. The state of rock mass stress, damage and deformation must first be simulated sufficiently requiring small-scale structures to be explicitly modelled. Supporting elements must be represented with high similitude and then the dynamic event must be applied to the system in the case of blasts, or evolve as a consequence of rock mass instability for seismic events. A special case is for the effect of pit blasting on underground excavations - discontinuous rock phenomena at scales from mine, to bench, to pillar, to tunnel need to be captured and this represents one of the most computationally intensive tasks in mine simulation. Recent advances in computer power allow these tasks to be completed at a mine scale, incorporating discontinuities and geological detail matching the best practice for static Finite Element analyses. The results are a worthwhile contribution to mine decision-making, but require careful interpretation and thoughtful inputs - even more so than quasi-static analysis - as the cumulative effects of unfavourable modeling practices are greater. Some learnings from experiences with mine scale, discontinuum dynamic simulation are summarised, including a discussion of considerations of scale and similitude for this type of analysis.

Nov 25, 2010

This paper presents a rationale for selecting appropriate support elements which combine to form a support system to maintain stability in mines subjected to both strainburst and the shaking that occurs from fault slip. The overall approach was developed during the 'case for safety' study undertaken to allow the then Beaconsfield Gold mine (now Tasmania mine) to resume development and production after the 25 April 2006 ground-fall and fatality that received worldwide publicity. Issues of the sometimes competing requirements of support element performance during dynamic loading are discussed and the need for support flexibility is contrasted with the usual high support element stiffness required when these are used to reinforce rock masses. An example is presented to show the steps and technical details required to design each component of a support system to counter the de-stabilising effects of seismicity.

Nov 25, 2010

The design of excavations in high displacement mining environments requires consideration of both the load and displacement capacity of the ground reinforcement and support systems. This paper is a case study on the design of point anchored rebar bolts using laboratory tests and field trials at the Ridgeway Deeps block cave. A laboratory testing program was carried out to measure the mechanical properties of the Strata Control Systems R27 Secura resin bolt which is currently being installed on the extraction and undercut level at the Ridgeway Deeps block cave. The aim was to quantify elastic, plastic and energy parameters for various bolt, mesh and plate systems. Experiments were performed on bar segments, bolt/plate systems, and bolt/plate/mesh/resin systems. The mechanical properties were calculated from tensile tests with a 500 kN Avery machine. Load-displacement data was collected from four different testing configurations. The laboratory results are compared with underground measurements and observations of bolt performance.

Nov 25, 2010

TSL Concepts and Practical Examples of the Non-Reactive System - Meyco TSL 865 Thin Spray-on Liners (TSLs) have been intensively investigated by mining and chemical industries within the last decade. Apart from the basic concept of spraying thin liners, expectations of the product's performance vary, eg immediate active strata support is seen as a key to control the ground permanently. For many coal mines this is an important factor to reduce maintenance in their roadways and enable permanent production from the long wall. In opposition to a passive mesh system this technology offers immediate active support to the strata. But not only coal mines are interested in TSL technology, there are potential applications in hard rock mines, during shaft sinking, pillar support and as an anti-weathering sealant. This paper will explain the advantages and disadvantages of TSL concepts; it will give examples of successfully applied TSLs with a main focus on the non-reactive and flexible system MEYCO TSL 865 by BASF. Furthermore, it will indicate the limitations and discuss briefly the bearing capacity and reasonable lab testing of such systems.

Nov 25, 2010

Entry of personnel under a vertical raise bored hole is not standard practice in Australia. Where access is required below a rise, mining operations must be confident that they understand the capacity of the ground control specified and installed. Physical modelling was conducted on Callie mine to evaluate the performance of 5 mm steel wire weldmesh secured to the base of a vertical raise bored hole of 1.4 m diameter. Joint orientation data was used with Unwedge to calculate a series of potential wedges likely to form within the rise. The mass of the most likely wedges were then replicated by collecting rocks in 5 kg increments (¦10 per cent), which were allowed to freefall onto installed mesh at the base of a 40 m vertical rise. The results indicate that two sheets of mesh can retain a freefalling rock of at least 20 kg mass although rupture of strands can result. This paper outlines the test conditions, expected results based on theoretical calculations and actual outcomes of the testing.

Nov 25, 2010

Development of a global failure criterion for rocks has been a desired goal in rock mechanics. Due to variations in factors affecting rock specifications and their mechanical properties, proposing a single failure criterion suitable for all rock types has proven to be unachievable. The theoretical failure criteria do not fit the real data correctly. Amongst empirical criteria, the Bieniawski criterion has demonstrated an acceptable agreement with laboratory generated data. It has been experienced that the ability to estimate rock strength via the modified form of this criterion is significantly improved. Based on the modified Bieniawski criterion and using VB.net, an associated Microsoft Windows program named 'RAMOCE' has been developed. The inputs of RAMOCE can be triaxial compressive strength data, Bieniawski parameters of a specific rock or the type of given rock. Based on input data, potential outputs of the program are Bieniawski's rock parameters, sensitivity analysis of the effective parameters, rock failure prediction and defining the type of given rock.

Nov 25, 2010