Search Documents

By Takeshi Nagano

"Prior to discussing future trends of non-ferrous metals smelting and refining, the past developments are looked back. Social and economic environments in Japan over the past two decades are reviewed. Technological developments to comply with these environments are explained, taking for examples the cases of the Mitsubishi continuous smelting and converting process and Onahama's jumbo tank system for copper tankhouse. After considering the factors which will influence the improvements in non-ferrous processing, future trends are forecasted generally for copper, zinc, lead, aluminum and rare earth metals. Recent development works in Japan for the future are also introduced. In the discussed area, it appears that the emergence of new innovative processes would be difficult. The progress will be made rather toward the sophistication of the existing technologies, utilizing the advancement of the related technologies such as computers, electronics, etc. IntroductionThis paper discusses the future trends of non-ferrous metals smelting and refining on the occasion of the international symposium, ""The Metallurgical Processes for the Year 2000 and Beyond"".It is considered that the improvement of technology is greatly influenced by the social and economic environments which surround it. From this standpoint, review was made of Japanese case over the past two decades. Various new technologies were developed also in the non-ferrous metal world to comply with the requirements under the above environments. The examples are described in the cases of the Mitsubishi continuous smelting and converting process and Onahama's jumbo tank system for copper electro-refining.After foreseeing the major factors which will affect the technological developments in the future, the trends are forecasted for copper, zinc, lead, aluminum and rare earth metals generally. Some development works in Japan, which will give suggestions for future trends, are also introduced in some detail."

Jan 1, 1988

By Mansoor Barati, Shaghayegh Esfahani

"The slag from extraction of ferrous and non-ferrous metals is a potential heat source which if treated properly can contribute to recovery of a significant amount of energy. The waste heat of slag may be used to generate steam, synthetic fuel gas, or electricity. Although several technologies have been investigated for this purpose, very little has been achieved in terms implementing the technology in industry. In this article, the development and application of various granulation techniques are reviewed and the methods to recover energy from granulated slag are discussed.IntroductionEvery year, more than 422 million tons of slag is being produced around the world as a by-product of the metal manufacturing at temperatures of up to 1300-1600°C [1, 2]. Currently slags are either disposed of or treated by processes such as granulation. Through the granulation process, most slags can be converted into a material which may be fully used as a cement feedstock. Conventional cement production is an energy intensive process with large emissions of CO2; therefore, the replacement can both be energy saving and environmentally friendly. However, for this purpose, the slag should have what is known as a “glassy” content (i.e. it should be amorphous) which requires rapid cooling rates that are not easily achieved due to the very low thermal conductivity. The main challenge in all these processes is to granulate the slag at a high cooling rate while the heat is also being recovered."

Jan 1, 2012

By T. R. A. Davey

Previous publications on the application of EIETSIM include the modelling of an electrolytic zinc plant and a copper flash smelter. In the present case METSIM has been used to model the desilverising of lead by the reagent zinc, whereby a silver-zinc intermetallic compound is formed, and floats out of the lead. This compound has a variable composition, depending upon the ratio of dissolved zinc/silver in the lead bath. Its solubility in lead decreases with falling temperature. A number of variations and modifications of the Davey Desilverising Procedure are modelled, and applied to a wide range of silver contents in lead bullions at several plants. METSIM uses both feed- back and feed-forward controls to simulate plant conditions, and a logic control to distinguish between different phases in the Zn-Ag system. Use is made of extensive (previously unpublished) fundamental data on the ternary Pb-Ag-Zn system, and of plant data, to establish certain operating parameters.

Jan 1, 1993

By C. M. Wai

"Metal species in solid and liquid materials can be extracted by supercritical carbon dioxide containing a suitable ligand. This in situ che1ation-supercritical fluid extraction technique offers several advantages over conventional solvent extraction including minimization of organic liquid waste generation and exposure of personnel to organic vapors. One unique feature of this technique is that metal species can be removed from solid materials directly using supercritical carbon dioxide as a solvent. Several ligand systems including dithiocarbamates, B-diketones, organophosphorus reagents, and macrocyclic compounds have been tested for metal extraction in supercritical carbon dioxide. This novel extraction technique may have important applications for metal recovery and mineral processing.IntroductionSupercritical fluid extraction (SFE) offers several advantages over conventional solvent extraction including the minimization of organic liquid waste generation and exposure of personnel to organic vapors.[1] The high diffusivity, low viscosity, and T-P dependence of solvent strength are some attractive properties which make supercritical fluids excellent candidates for extraction and recovery of organic compounds from solid materials [2] Carbon dioxide is a gas of choice for SFE because of its moderate critical constants (Tc = 31 °·C and Pc = 73 atm), inertness, and availability in purified form. After extraction, the fluid phase is depressurized to separate organic solutes from CO2 gas and the gas can be recycled for repeated use. The SFE technology has been applied to industrial scale operations such as the preparation of decaffeinated coffee and hop extracts."

Jan 1, 1996

By Hua Hou, Xiaofeng Niu, Wei Liang

"The explicit finite difference (EFD) method is used for calculating the casting temperature field during solidification. Because the time step is limited, the computational efficiency of the EFD method is lower. In order to improve the computational efficiency, a fourth-order in space and second-order in time model based on the equivalent specific heat method and the alternating direction implicit (ADI) method is established. The degree of similarity between the simulation results and the experimental results is analyzed. The results show that the simulation results of this high order mathematical model are close to the experimental results.IntroductionThe 3D heat transfer equation of temperature field during solidification process is as the following: [1-3]."

Jan 1, 2013

By G. G. Richards

The zinc slag fuming process is used to recover zinc from molten iron-calcium silicate slags by treatment with pulverized coal and air. The rate of zinc fuming is controlled by the complex interaction of several kinetic factors including the rate of entrainment of coal in the slag, the extent of the coal-slag reaction and the rate of ferrous oxide oxidation to ferric oxide. This paper briefly outlines the mechanism of fuming and, on this basis, optimization of process parameters is discussed. Modelling analysis and recent industrial trials at Cominco show that coal entrainment in the slag, bath temperature, and bath depth are critical variables affecting process rate and efficiency. The first step in process optimization is to assess coal bypass of the bath. In general, changes which promote operation at a higher temperature, greater coal entrainment in the slag and extended residence time of the coal in the bath increase fuming performance. Coal entrainment is controlled by injection conditions whereas bath temperature is a function of coal combustion and ferrous oxide oxidation. Residence time of the coal is largely a function of bath depth. The implication of model predictions for continuous fuming is shown.

Jan 1, 1994

By S. Yabe

The reinforcement of the annual copper production capacity to 330,000 metric tons has been attained at Saganoseki Smelter & Refinery in 1991, which is one of the largest and most efficient custom smelters in the world. Many operational improvements and technology developments have realized the increase of smelting and refining capacity without adding main facilities to the existing process. The blister copper refining and anode casting process is composed of two 400 tonnes anode furnaces and one double-wheeled casting machine with the capacity of 80 tonnes per hour. The great innovations in this process such as the finding of essential issue on the extending of anode-mould life and the development of a new anode-mould casting machine have raised the operation efficiency by 14% Now, the process is producing 38,500 tonnes per month of best quality anode in well- controlled working condition, and anode productivity per worker increased by 52%. The progress in extending anode-mould life, the mechanism of the new anode-mould casting machine and the increase of efficiency in butane reduction, that were the principal parts of many technological improvements, are described in the present paper, including some operation results.

Jan 1, 1993

By Kyong-Hwan Lee

This paper is focused on describing the pilot and demonstration plants for pyrolysis process of mixed plastic wastes developed at Korea Institute of Energy Research (KIER). These plants were constructed at KIER (300 ton/yr) and also Korea R & D Company (3,000 ton/yr) in Kimjae city, in Korea. The raw material used was mixed plastic wastes that were generated from household and industry, etc. The liquid products obtained by pyrolysis at around 400°C were used as an alternative fuel oil. These processes were controlled by automatic control system with continuous operation in a control room. Main process units consist of automatic feeding, melting, thermal cracking systems and vacuum distillation. Their characteristics were automatic pyrolysis operation under vacuum atmospheric pressure, continuous control in feeding of raw material and discharging of solid residue, the recirculation of cracked reactant with a high temperature into the melting reactor and continuous pyrolysis of reactant in circulation thermal cracking system such as constant stirred tank reactor (CSTR), plug flow reactor and light/heavy oil separator, in order to maximize the efficiency of light oil products like kerosene and diesel. In addition, the process performance of pilot plant was described.

Jan 1, 2006

By Donald R. Fosnacht

An investigation was initiated to obtain the scope of the problems associated with recycling various waste oxide materials generated at Inland Steel and to identify and? test techniques that could possibly aid in increasing the amount of waste oxide materials recycled to primary. operations. Based on the results of this work, several new techniques were developed ?and tested on ?a plant or laboratory scale. These include the use of cold-bond agglomeration methods for producing waste oxide agglomerates for use as a cooling agent or scrap substitute in steelmaking operations, and the use of various techniques for beneficiating blast furnace flue dust and soaking pit rubble so that the upgraded materials can be utilized in sinter plant or ironmaking operations. The physical and chemical characteristics of the waste oxide materials and the results of the laboratory and plant testing are discussed in this paper.

Jan 1, 1985

By A. M. Strachan

The arising and behavioural pattern of polonium-210 in the Capper Pass & Son Limited non-ferrous metal smelting and refining circuit is briefly discussed. The process developed for the removal of polonium from lead, solder and bismuth is discussed in detail, together with the essential personnel safety and environmental protection precautions which must be taken during the refining and subsequent storage of the active dross.

Jan 1, 1992

By Zhihe Dou

SHS reaction system has advantages of heat flux density, energy concentration and reaction speed, with sufficient conditions in thermodynamic and kinetic reaction. This paper invented a new technology of SHS metallurgy of preparing melting point alloys and refractory compounds using its own chemical energy. SHS-leaching process for preparing nano boron powder or ultrafine boride powder and SHS-casting process for preparing titanium-based alloy and immiscible alloy were studied. The results indicate that highly active boron powder of greater than purity of 93%, particle size less than 100nm and purity greater than 98.5%, particle size less than 400nm REB6 can be prepared. With SHS-Casting process, the oxygen content of less than 0.59% ferrotitanium, oxygen content of less than 0.5% titanium alloy and ?40-80*100mm large size of CuCr, Cu-Fe alloy ingots were prepared. This technology has greatly enhanced the thermal reduction method added values of preparing metallurgical products and its competitiveness.

Jan 1, 2014

By Nedam Abed

A fundamental study of the sonochemical leaching of chalcopyrite in ferric ion media has been performed to understand and quantify the effects of sonication and other parameters on leaching reactions. The study covers sulfate and chloride media. The main leaching reaction: CuFeS2(s) + 4Fe3+(aq) Cu2+(aq) + 5Fe2+(aq) + 2S(s) (1) was found to be dependent on temperature and initial particle size, but less dependent on ferric ion concentration. Leaching kinetics were not affected by ferrous ion concentration or the amount of chalcopyrite added. Leaching was performed under a variety of sonication and leaching conditions. Reaction stoichiometry was confirmed through detailed wet chemistry analysis and mass balance calculations. The use of ultrasound activation showed a clear improvement in leaching kinetics and amount of copper extracted, sonication having a catalytic-like effect on the leaching reaction. Compared to experiments without sonication, reaction rates were 2-3 times faster at the same temperature, and could be faster by a factor of 20 for the same initial particle size. Regardless of initial particle size, the amount of copper extracted was comparable under sonication, and could be twice that under chemical leaching, implying the avoidance of fine particle grinding. Sonochemical leaching was found to be only temperature dependent, where the best copper extraction was at 75C. Leaching was further enhanced by the use of a grinding aid. The leaching behavior of chalcopyrite particles remained similar with and without ultrasound activation, implying that the known passivation mechanism in the oxidative leaching was not eradicated. Sonication resulted in coarse particle breakage (ultrasonic milling). Sonication did not contribute to particle passivation, as affirmed from different leaching procedures and sonication in aqueous and organic media. Parabolic leaching kinetics were confirmed for leaching experiments.

Jan 1, 2003

By Michael S. Moats, Scott C. Campin, J. Brent Hiskey

"Electrochemical techniques are a valuable means of analyzing the passivation of commercial copper anodes. Electrochemical impedance spectroscopy (EIS) provides information concerning transport and reaction phenomena occurring at an electrode surface. Commercial. copper anodes of varying compositions have been examined using EIS. Experiments were conducted in a flat cell with an electrolyte of 40 gil Cu2 + and 160 gil H2S04 maintained at 65 DC. Impedance spectra were obtained at the potentials characteristic of the open circuit voltage and passive region for each anode. The spectra of the passivating films exhibited a flattened resistive/capacitive loop at middle to high frequencies and an inductive loop at low frequencies. An equivalent· circuit utilizing an inductor-resistor series in parallel with the double layer capacitance and charge transfer resistance was adequate in modeling the impedance data. The influence of anodes impurities on the components of the equivalent circuit is discussed and correlated with a hi-layer passivation model.IntroductionPassivation of copper anodes during industrial electrorefining has received considerable attention in the past few decades. Great strides have been made in understanding the roles of anode impurities [1-25], electrolysis parameters [20,26], and electrolyte chemistries [20,26]. Even so, passivation still occurs even in the most modem of refineries. The exact cause of passivation is not fully understood. It is known that the anode surface becomes covered by a passivating film. This film has been proposed to be CuS04'&5H20, Cu20, or mixed oxides. The localized concentrations of Ft, Cu+, and Cu2+ ions determines which phase is more favorable. The presence of these ions is controlled by the reaction kinetics and diffusion of species through the slimes layer.Reaction kinetics between Cu, Cu +, and Cu2+ are based on the dissolution mechanism of copper. There exists four different models to describe the dissolution of pure copper. The classical model of Mattsson and Bockris [27] involves two single electron transfers with the cuprous-cupric reaction being the rate detennining step. More recently, Wong, Collier, and MacFarlane [28] used ac impedance to elucidate a more complex mechanism involving the affect of pH and anions. Their findings indicate that the formation of cuprous ions in solution, Cu(I)so~ is favored over Cu(1I) ions adsorbed to the electrode surface in the presence of sulfate and as pH increases from pH 1 to pH 5."

Jan 1, 1997

By Nils Eivind Kamfjord, Roar Jensen, Ingeborg Solheim

"SINTEF has carried out several pilot scale silicon process experiments in the past, but always with an open off gas system. In order to test the possibilities in running a semi closed furnace operation, a new off gas hood has been designed and tested. The off gas hood is designed to collect all off gases to gain insight into the phase compositions in the off gas and at the same time have the opportunity to monitor and maintain the charging/stoking of the furnace. The furnace hood has regulation and control of the air inlet into the combustion zone in two different heights. The off gas temperature and composition was continuously monitored and analyzed during the experiment. In order to expand the knowledge on NOx- formation in silicon metal production, such information is vital.IntroductionBecause of the negative environmental impact, the attention towards all kinds of NOX emissions increases in Norway. The authorities’ demand towards better surveillance and control of emissions increases as well.Earlier and new industrial measurements in FeSi- and Si-metal furnaces reveal quite high NOX-emission. The measurements also show that the NOX formation (mainly as thermal NOX) is distinct connected to the formation of dust (SiO?SiO2) in the combustion chamber above the furnace surface, when the temperature is high and the access to N2/O2 is good. This means that stoking, charging and temperature straight above the furnace surface is important factors for the NOX formation."

Jan 1, 2012

By Lætitia H. Delmau

SXFIT is the latest in a series of programs developed in our group to model solvent extraction systems of increasing complexity. SXFIT permits the user complete freedom to define the constituents from which the composition of each phase is to be specified in the data and from which all species of a model for a system are assumed to be formed. Activity coefficients in the nonaqueous and aqueous phases, water activity, apparent molar volumes of aqueous species, and solution density needed for the conversion of concentration from the molarity to the molarity scale are all taken into account by the program. Several extraction systems relevant to nuclear-waste treatment were modeled successfully using this program. As an example, the cesium extraction efficiency of the CSSX process chosen by the USDOE for cesium removal from high-level waste stored at the Savannah River Site can be predicted correctly for varying feed composition.

Jan 1, 2003

By Matti Hämäläinen

Outokumpu has developed a new chloride leaching process, HydroCopper?, for copper concentrates. The process utilizes the cupric ion as oxidant, which is able to dissolve chalcopyrite. After solution purification monovalent copper is precipitated as cuprous oxide, Cu2O, using sodium hydroxide. Copper product is produced from Cu2O by reduction, melting and casting. An essential part of the new process is chlor-alkali electrolysis, which regenerates the reagents used. All impurity metals are removed before Cu2O precipitation, because otherwise they would report to the copper product, impairing its quality. A multistage solution purification scheme has been developed consisting of firstly, chemical precipitation of impurity metals by pH increase, secondly, cementation of silver and thirdly, removal of trace multivalent ions using ion exchange. This paper describes the characteristics of solution purification in the HydroCopper? process based on the laboratory tests and pilot runs made by Outokumpu Research Oy.

Jan 1, 2003

By R. Boom, B. Kraaijveld, H. Kuntzel, Y. Meteleva-Fischer

"Alloying refining with rare earth elements followed by acid leaching was examined for the potential of upgrading of metallurgical grade silicon. Microstructure study of silicon alloyed with small additions of rare earths showed behavior relatively similar to the influence of calcium addition. After alloying with neodymium the phosphorus content was detected in various intermetallic silicides containing neodymium and iron. The content of lanthanum and neodymium in refined silicon was by several times lower than that of aluminium and calcium. Alloying with lanthanum and neodymium at smaller additions than calcium reduced the phosphorus content down to the same level. The efficiency of lanthanum and neodymium in removal of boron and phosphorus at the 1-2 wt% of their additions and their low solubility in silicon make the alloying with these metals followed by acid leaching an attractive option for the refining route of metallurgical grade silicon up to solar grade.IntroductionA striving for a cheap ""green"" energy directs the research interests in silicon solar cells towards new efficient refining routes for metallurgical grade silicon (MG-Si, -98% purity). The silicon price determines up to high extent the solar module's price, so that cheap and efficient metallurgical process is awaited. The research challenge is to fulfil the purity requirements of solar grade silicon (SoG-Si, 6N) by competing with the energy-consuming and environmentally unfriendly Siemens process. Most difficult impurities to remove are boron and phosphorus, so technologies dedicated to their efficient removal attract an attention of industry and academia.Alloying refining (also known as solvent refining) is one of the most promising refining options, which is based on a principle of solid-liquid extraction using limited solubility of impurity elements in solid silicon [ 1]. Various elements were proposed for alloying refining: aluminium [2], calcium [3], tin [4], iron [5], copper [6] etc. The attractiveness of the alloying refining is in decreasing a melting point of the metal mixture and an affinity of the alloying element to the most harmful impurities, especially to boron and phosphorus. However, the difficulties are still faced due to self-solubility of the alloying elements, their low affinity to boron and/or phosphorus, silicon losses and necessity of removal of the silicide impurity phases in an additional step, using acid leaching [7], fractional melting [ 8] etc."

Jan 1, 2013

By Thomas A. Post

The methodology of determining the optimum SX pumper-mixer system based on bench top, pilot, or small-scale solvent extraction systems, is demonstrated. The design of small-scale SX-plants is different than a full-scale plant. The difference is explained here. The use of dimensionless parameters Nh, Nq, and Np that describe the head, flow and power of the pumper is shown and how to use them for the scale-up. Additional data is required to determine the optimum operating range. Applications of this methodology were used to design well known currently operating SX plants. The emphasis on the optimization of hydraulic efficiency will be shown on examples, including how the hydraulic efficiency is affected when the throughput of the system goes beyond the design. Designs of all sizes of equipment will be shown which optimize the hydraulic efficiency.

Jan 1, 2003

By Stober, Frank Allan

The paper describes the development of components in an lntegrated Furnace Control system for shielded-arc smelting focusing on operation and crucible integrity enhancement. The paper reviews the mechanisms of power, feed and energy input and losses into the shielded-arc smelting process and describes the furnace control system module development and integration to tailor the process. The ultimate success of a furnace control system application is transfer of knowledge, training, and operational support during furnace start-up and ramp-up phases and a model for how this has been achieved is discussed. The control modules of a shielded-arc laterite smelting furnace are described in detail including measured results and screen captures from application in a laterite smelting furnace. This paper focuses on developments in Integrated Furnace Controls tailored to shielded-arc laterite smelting but development of common furnace control modules for improved crucible and tapping operation integrity applied to other furnace processes, including immersed-arc smelting, is also covered. Keywords: IFC, Power, Feed, Supervisory, Control

Jan 1, 2004

By H. Ipek

In this study the effects of interstitial ratios on k-feldspar samples were investigated. The k-feldspar samples were taken from Egypt using dry batch grinding conditions and a kinetic model. Three different mono size fractions (-3350+2360, -850+600 and -300+212 µm) were ground separately for 0.5, 1, 4, and 8 minutes and at four different interstitial ratios (125%, 100%, 75% and 50%) using a Bond mill with a mixture of five ball sizes. The mill used was at a size of 30.5 cm diameters, with 30.5 cm length, providing a total mill volume of 22272 cm3. The mill has a total mass consisting of 22648 g. steel ball mixtures of 38.10, 31.75, 25.40, 19.05 and 12.70mm diameters, occupying 22% of mill volume. The mill rotates at a speed of 70 rpm. The weights of the feed charges were 3000, 2000, 1000, and 500 g for 125%, 100%, 75% and 50% filling of the interstices of the balls respectively. The specific rate of breakage (Si) was determined from the top size fractions at different grinding times that were mentioned above and the model parameters were compared for the four different powder filling ratios (U). In many investigations, it has been found that an interstitial filling ratio of U = 0.6-1.1 is a good powder ball loading ratio to give an efficient breakage in a ball mill. In this study, it was found that U=1.25 is a good ratio for K-Feldspar.

Jan 1, 2006