Search Documents

By Tammy G. R. Portela

A comparative characterization of the dimensional and mechanical properties as well as structural aspects of two different types of fibers extracted from the leaves and petioles of the buriti palm tree was performed. A statistical analysis revealed that both types of fibers present a significant dispersion in length and equivalent diameter. However, the corresponding intervals of dimensional variation are sensibly different. The tensile properties showed that both types of fibers display a tendency of higher strength for smaller diameters. Moreover, the fibers extracted from the leaves depict a comparatively lower strength. By contrast, the fibers from the petiole present an average strength sufficiently high for the use as reinforcement of polymeric composites. The structural aspects of tensile-rupture fibers, characterized by scanning electron microscopy, showed marked distinction in the microstructure and fiber behavior of both types of investigated fibers. This could explain the differences in mechanical behavior

Jan 1, 2010

By Gus Van Weert

The cost of oxygen is a major and common factor in the hydrometallurgical processes developed or proposed tor the oxidation of refractory pyrites. This cost involves charges for the generation and the transfer of the 02 to the mineral slurry. Bio-oxidation faces considerable design demands which require large scale equipment to be resolved. Nitric acid assisted oxidation offers low cost oxygen units; this method of pyrite oxidation deserves a closer look for large scale plants treating pyritic gold ores and concentrates.

Jan 1, 1990

By Adolfo Pillihuaman Zambrano

Fe-Cr-C production is a very high electrical energy consuming process. Decrease up to 10% of this electrical energy is expected when self-reducing agglomerates are used. This research aims to understand how the synergetic effects are when stronger reductant, like Fe-Si, is substituted for coke in self reducing pellets. Brazilian chromites containing 41.2%Cr2O3 were mixed with petroleum coke and agglomerated with cement as the binder. Small amounts of 1%, 2% and 4% of Fe-75%Si were substituted for the equivalent petroleum coke, and pure silica plus hydrated lime were added for adjusting the slag composition. The mixture was pelletized, dried and submitted at 1773K up to complete the reactions. The results showed that the reduction reactions were 1.4 and 2 times faster with 1% and 2%Fe-Si addition, respectively, than with no addition. The microscopic analysis showed that it was formed a liquid phase, but the pellet did not collapse what indicates that the coalescence of the metallic phase depends on the dissolution of the pre-reduced particles of the chromites into slag.

Jan 1, 2008

By H. Cepin

Production of non-ferrous metals is still principally performed in shaft and flame fired furnaces. Electric furnaces increase metal recovery, reduce environmental burdens and decrease energy consumption compared to conventional processes. Because non-ferrous metals have low melting and boiling points and aggressive slags design of the furnace, energy input, and slag conductivity and composition are very important. Secondary materials are easily handled in electric furnaces. Since additional amounts of lead, zinc and tin will become available from secondary sources in the future, electric furnaces are expected to replace conventional smelting furnaces. The paper describes technical, electrical, and process designs of electric furnaces peculiar to the reduction of non-ferrous metals. Electric and various thermic furnace processes are compared.

Jan 1, 1990

By Yoshiaki Suzuki

Since 1973, Saganoseki Smelter & Refinery had operated two flash smelting furnaces together to produce 330,000 mtpy of copper. However, in 1990's, economical situation required the smelter more increased productivity to remain competitive. The program, to integrate two flash furnaces into one was carried out maintaining the same production. Modifications were done on the pneumatic concentrate drying system, concentrate feeding system, concentrate burner and furnace cooling system, etc. to double the, furnace throughput. A new large cryogenic oxygen plant was constructed replacing two old plants. Single flash smelting furnace operation has started in March 1996. This paper describes about details of modifications and operational results.

Jan 1, 1998

By M. M. Kim

As-electrogalvanized coatings of pure Zn, Zn-11% Fe, and Zn-18% Fe coatings were characterized in terms of initial crystal structure and surface morphology. Samples were then subjected to heat treatments simulating the paint bake cycle of automobile manufacturers. Surface morphology changes were correlated with the process variables, and crystallo.graphic changes were interpreted by mapping heat treatment routes on the Fe-Zn phase diagram. The morphology of pure zinc electrogalvanized coatings with heat treatment from platelets to smeared platelets. The zn-11% Fe coating changes with heat treatment from tetrahedral nodules to a mixture of round and tetrahedral nodules, with the Zn-:18% Fe coating always having round nodules. Regarding crystal structure, a critical transformation time can be defined at any selected temperature, below which the crystal structure does not change. This temperature is related to iron content.

Jan 1, 1990

By Peng Fan

Liquid phase tends to migrate from an aggregate of solid particles immersed in a liquid phase into another aggregate composed of the same solid particles and liquid but with smaller particle sizes and/or lower volume fraction of the liquid phase. This type of liquid migration in a two phase system can be attributed to the driving force for the system to decrease its total interfacial energy. With liquid migration pressure as a convenient measure for the total interfacial energy of a solid-liquid two-phase system, liquid migration can be attributed to the existence of liquid migration pressure gradient in the two-phase system. The kinetics of liquid migration is of great practical importance for many industrial processes, one of which is the liquid phase sintering of functionally graded WC-Co composite materials. During liquid phase sintering, WC-Co composite forms a typical solid-liquid two-phase system where solid particles of WC are immersed in liquid Co. For a sample composed of two layers of WC-Co with the same Co content but different WC particle size, Co gradient will be formed during liquid phase sintering; while for a sample composed of two layers of WC-Co with the same WC particle size but different Co content, the Co gradient will be eliminated during liquid phase sintering. The formation and elimination of Co gradient are controlled by the liquid migration pressure gradient. This paper describes a numerical simulation of the kinetic process of the formation and elimination of cobalt gradient.

Jan 1, 2006

By Alice Barreto Bevitori, Frederico Muylaert Margem, Renan Sopeletto Carreiro, Sergio Neves Monteiro, Isabela Leão Amaral da Silva

"The ramie fiber is one of the strongest lignocellulosic fibers with applications ranging from simple items such as fabrics and ropes to engineering composites for automobile parts and building panels. Characterization of the ramie fiber has recently been conducted for physical and mechanical properties. In principle, thinner ramie fiber could be comparatively stronger and consequently more effective as a composite reinforcement. In this work an attempt to correlate the ramie fiber elastic modulus obtained in tensile test with its corresponding diameter, precisely measured by means of a profile projector, was carried out. Tensile results analyzed by the Weibul1 statistic showed a significant increase in elastic modulus with decreasing the diameter of ramie fiber. Scanning electron microscopy observation of the fracture of selected ruptured fiber revealed possible mechanisms that could justify the elastic modulus/diameter inverse dependence.IntroductionEngineering applications of natural fibers obtained from cellulose-rich plants, also known as lignocellulosic fibers, are currently being the focus of attention. In fact, they are considered an enviromnental1y correct alternative to substitute synthetic fibers such as the glass fiber, associated with an intensive intake of energy during production, as reinforcement of polymer composites [1-4]. In recent years there has been a growing tendency towards the use of lignocellulosic fiber composites in several industrial sectors from civil constructions to car making. In particular, the automotive industry is expanding the number of both interior and exterior components made of natural fiber composites [5]."

Jan 1, 2012

By O. Forsén

In the first part of this paper is studied the behaviour of small amounts of impurity elements? in the solidification of copper anodes. In the second part the dissolution of these impure anodes in sulphate based electrolysis is discussed. The first part is introduced with practical examples, the .model of solidification of impurities during the solidification of anode copper. According to this model the solidification structures of anode copper are strongly influenced by both thermodynamic and kinetic factors. Thermodynamics determine the microstructure of anode copper, but kinetics can alter the composition of melt to such that there is formed unequilibrium structures during the solidification, especially when the residual melt is solidified. The electrolysis experiments have clarified the behaviour of impuririties in the electrochemical dissolution in sulphate. Based copper electrolysis. In this study it is widely investigated to what extent any impurity elements or oxides will dissolve. In copper electrorefining. With the aid of the electrochemtcal experiments it was possible to fulfil quantitatively the qualitative results accomplished by microstructure studies.

Jan 1, 1985

By T. J. A. Smith

This paper provides an overview of some of the key issues in design of smelter gas handling systems, with particular reference to smelter smelting plants. In both primary smelting and converting, gas handling and treatment systems often represent the major capital cost component. There is also ample evidence that poor system design can be a major cause of smelter down time, lost production and unforeseen high maintenance costs. The paper discusses these issues and offers guidance for improved design.

Jan 1, 1992

By Othon do Rêgo Monteiro Neto

[The present study has investigated the extraction of copper from a chalcopyrite flotation concentrate using an adapted strain of Thiobacillus ferrooxidans and shake flasks, tank leaching and Warburg respirometer techniques. From the shake flask experiments, the activation energy and the frequency factor have been determined to be ?ka = 59.4 kJ and A = 3.3 x 105 S-1, respectively. The temperature coefficient was found to be Q10 = 2.2 in the range of 20 to 35°C. It was suggested that the reaction mechanism of chalcopyrite leaching by T. ferrooxidans involves the formation of an activated complex. whose thermodynamic values have been calculated to be ?G? = 92.1 kJ, ?S? -148.8 J K-1 and ?H$ = 47.8 kJ. The maximum volumetric oxygen mass transfer coefficient for the reactor leaching was found to be achieved by using an optimum air flow rate of 1970 cm min l at a rotational frequency of 1000 min-1. The highest copper extraction in tank (reactor) leaching experiment was 86.8% after 17 days of leaching, while in the sterile runs the corresponding copper extraction was only 40.1%. The copper extraction was suggested to be diffusion controlled. The power requirement of the aerated reactor was calculated to be Pg = 2.02 watts. During leaching, the oxygen saturation concentration was found to be C* = 6.70 mg dm-3. Using the gassing out method the critical oxygen concentration was assessed to be CCrit 0.05 mg dm 3. From the Warburg experiments, the kinetic parameters of the Monad equation were derived with a new evaluation technique to be Vmsp = 9.0 µm3 02 min-1 mg protein-1 and K = 7.4% pulp density for the effect of substrate concentration. The order of reaction and the overall reaction rate constant were determined from the modified van't Hoff plot to be n = 0.0 and k = 1.49 p dm3 02 min-1 mg Protein -1 for the chalcopyrite concentrate oxidation by T. ferrooxidans. On the basis of this experimental work, a preliminary flow sheet has been proposed for the bioextraction of copper from flotation concentrates.]

Jan 1, 1985

By Qionghua Zhou, Wei Liu

"Nanocrystalline silver bulk material with average grain size of 20.3 nm was prepared by warmvacuum- compaction method. The as-prepared nanocrystalline silver was characterized by X-ray diffraction (XRD), differential scanning calarmeutry analysis (DSC), thermogravimetric analysis (TG), and 6157 type Electrometer test, respectivily. The experimental results show that the average grain size and microstrain of the nanocrystalline silver are 20.3 nm and 0.088%. The melting point and melting enthalpy are 1228.7 Kand 82.34 Jig, which are lower than that of coarse-grained silver by 6 Kand 22.6 Jig, respectively. The electrical resistivity of nanocrystlline silver increases with higher temperature when the range of temperature is between 233K and 293K. The electrical resistivity at 293 K is 1.475xlO -7 Q·m, which is higher than that of coarsegrained silver by a factor of 9.IntroductionN anocrystaline ( nc) materials or nano structured ( ns) materials are three-dimensional (3 D) bulk materials with average grain size typically smaller than 100 nm. Ne materials have been of great interest for their unique properties, such as superior tensile strength [1-2], high microhardness [3- 4], superplasticity [5-6], magnetically quasi-isotropic [7-8] , and so on, making them one of the most promising nano-scale materials with wide applications. Ne materials with average grain size of 5-10 nm were firstly fabricated by Gleiter et al. [9] in 1980s, using inert gas condensation (IGC) method. Unfortunately, the large surface to volume ratio creates a high surface energy component in the total free energy of the system and results in a metastable state in the materials. Therefore, due to the signfica nt disordered grain boundary regions, nanomaterials are thermally unstable and are subjected to a strong driving force for grain growth. The grain growth even occurred at room temperature [10].The conflict or deviation of measured date, e.g. strength, microhardness, thermal stability, partly due to the grain boundary ratio or the distribution of grain size, and partly derived from imperfections such as voids and microcracks while earlier processing techniques are known to result in incomplete dens:fication [11-12]. Therefore, the higher quality samples produced in subsequently years still show such a general trend."

Jan 1, 2011

By H. -Peter Sattler

The laser sorting technique for replacing the handpicking of the non-ferrous metal scrap from auto shredders was first introduced 1990, The process is based on the use of atomic emission spectroscopy induced by lasers to identify the scrap particles and sort them with adequate systems into main fractions of Al-, Zn-and Cu-alloys, stainless steel and lead, In the meantime the handling technique for the scrap, i.e. the singling and sorting technique as well as the analytical detector were further developed for more efficiency and higher reliability, i,e. less maintenance, minor sorting errors etc. These developments were mainly based, on and initiated by operational experiences from the startup phase of a first production plant. Part of the on going research work was the development of an ,aluminium detector which makes it the first time possible to sort mixed aluminium scrap automatically into specific alloy fractions.

Jan 1, 1995

By C. -S. Jiang

In most copper refineries, addition agents are added at predetermined rates with no further monitoring of their activity or concentration in the electrolyte. Increasingly stringent cathode quality requirements, and a desire for better process control in tankhouse operations, have recently directed a number of refineries to search for a better addition agent control strategy. Extensive development work has been carried out at the Noranda Technology Centre for the monitor in of glue and thiourea in copper refinery electrolyte using cyclic voltammetry (cv~. Data from both synthetrc and commercial electrolytes are presented, showing the ability of CV to produce reliable and easily identifiable fingerprints of addition agent concentrations in copper refinery electrolyte.

Jan 1, 1991

By Dai Yongnian

The methods of treating zinc crust and its development in the last hundred years are compared and reviewed. There are better effects from normal pressure metallurgy turned into vacuum metallurgy. The traditional methods dezinc only. But we must consider that delead on further step. From lab tests to industrial scale experiment are researched. The first step-dezinc, second-delead, crude ,metal of, zinc, lead and silver are produced, The flowsheet of treating zinc crust are simplified, material consumption reduced, work condition improved, environment protect mended. This method is pointed out that its application can be expanded.

Jan 1, 1992

By Reinhard Bott

The Companhia Mineira de Metais (Brazil) runs a Zn-recovery plant in Tres Marias, federal state Minas Gerais, Brazil. The Zn-production is about 65,000 t/a, This corresponds to a concentrate throughput of about 255,000 t/a with a Zncontent of about 29.5 % at an output of 85 %, The plant is run continuously 360 d/a and 24 h/d, respectively. From this it can be concluded that: Input: approx. 650 - 700 t/d ore-concentrate and approx. 29 t/h ore-concentrate, respectively.

Jan 1, 1990

By R. Burkhard

Recovery of metals from complex mixed wastes is a challenging task of modem material and waste management strategies. Thermal methods are an important tool in this respect. Plasma turned out to be particularly useful for treatment of complex or toxic wastes and residuals. In order to study plasma processes at reasonable costs, a pilot plasma plant has been used and wastes like ~pent Raney-Nickel catalysts, copper and ah.:lminum drosses, and. other metal containing wastes were investigated. The paper summarizes the most significant findings

Jan 1, 1995

By Yongbin Yang, Meixia Cai, Yufeng Guo, Guanzhou Qiu, Tao Jiang, Jianjun Fan

"A series of sintering and metallurgical experiments were carried out to optimize the blast furnace burden structure in this study. The results indicated that the sinter disintegrated seriously with basicity around 1.4, and after this “turning point”, the sintering properties were improved gradually with the increase of basicity of sinter. Based on the results, an idea was put forward which focused on producing two different kinds of sinter with different basicity. Different with the original burden structure of 85% sinter with basicity 1.4-1.5 + 15% pellets, an alternative new BF burden structure was proposed by the following structure?44% sinter with basicity 1.05 + 44% sinter with basicity 1.87 + 12% pellets. This new alternative BF burden structure has been adopted by some steel plants.IntroductionIn recent years, conventional blast furnace (BF) process was put into operation to produce hot metal in “A” steel plant. “A” steel plant owns two sets of sinter strands at present. Because the sinter production capacity exceeds the actual requirements of BF, a burden structure with 85-90% self-made sinter + 10-15% purchased pellets is adopted to take advantage of the low–cost sinter. But the serious problems encountered with the BF operators are that the sinter disintegrated easily during transportation and storage process. Therefore, the rate of return fines is very high after sinter being screened."

Jan 1, 2012

By F. F. Aplan

Though over 100 minerals are known to contain the rare earth (RE) or lanthanide elements, only a few provide the bulk of the world's source of these elements. The principal RE-containing mineral, monazite [(Ce,La,Th,Y)PO4], is recovered by gravity, magnetic, electrostatic and flotation concentration methods, while the other important source mineral, bastnasite [CeFC03], is concentrated by flotation. The processing of the lesser important source minerals is discussed, as is the recovery of the lanthanides from apatite [Ca5(P04)3(F,OH)] where the rare earth elements are present from trace amounts to over 10% as the mixed oxides.

Jan 1, 1989

By Harvey Alter

National attention in, recycling focuses on municipal solid waste (MSW), even though only about 50'million tons or so of MSW can be recycled, including grass, leaves and other yard wastes. The scope and value of the recycling of industrial "wastes" is much greater. It is possible to account for some 240 million tons of material recycled at the industrial scale annually, which is likely a conservative estimate. Some of this recycling reduces what would otherwise be hazardous waste to 'comrnodities and non-hazardous residue. Global trade in recycled commodities is outlined, as well as the-effect of the Basel Convention on the Trans boundary Movement of Hazardous Wastes A recent Decision under the Convention can, diminish the trade; deny developing countries needed secondary raw materials, and put world markets in chaos. Current U.S. government policies and activities toward ratification of the Convention, and possible new regulation of industrial recycling activities, will be discussed. There are federal proposals that would regulate industrial recycling differently for on-site and off-site facilities and judge legitimate or "sham" recycling according to the concentration of so-called "toxics along for the ride."

Jan 1, 1995