Search Documents

By Mitsutaka Hino

The contents of gangue minerals, such as Al2O3. P2O5, crystalline water and so forth in the iron ore imported to Japan tend to increase year by year. Though the increments of such gangue contents arc approximately 0.1-0.2 mass%, some problems for the blast furnace operation in ironmaking process have already been reported, In order to clarify the mechanism of harmful effect caused by the small increment of gangue minerals, mainly Al2O3. on the blast furnace operation, the dripping behavior of Fe,O-CaO-SiO2-Al2O3-MgO slag from the iron funnel, which simulated the micro-porosity in sinter ore, has been observed with the wide range of basicity, Al2O3, Fe2O and MgO contents. The effect of MgO on the dripping behavior of slag has been summarized in this paper. It was found that the addition of 2mass% MgO resulted in large increase of hold-up on the most of the conditions. When Fe2O content was less than 20mass% and the basicity was lower than 0.8, MgO lowered the hold-up even if the slag contained 10mass% Ah03. Every slag hold-up showed the minimum at the basicity of less than unity on the conditions of constant Fe2O and Al2O3 contents, This trend became remarkable when the slag contained 2 mass% MgO.

Jan 1, 2003

By Egil Krystad, Merete Tangstad, Kai Tang, Gabriella Trenell

"A new UMG-Si refining concept has been proposed in this paper. Liquid Si and another liquid metal phase (Me) were separated by the molten slag spontaneously based on their different physicochemical properties. Two metal/slag distribution reactions are able to occur in the system simultaneously. Experimental investigation on the B and P distribution equilibria among Si/slag/Me was carried out in the graphite resistance furnace under the inert atmosphere. The B and P doped silicon was in equilibrium with either the SiO2-CaO or SiO2-CaO-l0%CaF2 slags at 1600 and 1650°C, respectively. The pure Fe and Cu metals were used in order to ""capture"" B and P in the slag phases. B and P in samples were determined by the ICP-MS. B and P distribution coefficients for the Si/slag/Me equilibria were compared with the theoretical calculations. The possible kinetic barriers for the Si/slag/Me three-layer equilibria have been analyzed. The metal contaminations in the three-layer equilibria were also examined. The present study provides a new approach for the refining of MG-Si.IntroductionMost of the impurities in the metallurgical silicon (MG-Si) are rather ""dilute'', ranging from few to several thousand ppms. However, the target impurity levels for upgrade metallurgical silicon (UMG-Si) feedstock are often far below the level of ppm. In such extreme case, the conventional refining technologies face the great technical challenges. B removal by slagging has already been implemented industrially. Removal of Pis frequently carried out by the vacuum distillation. The separating treatments for B and P removals lead to increase refining cost, total CO2 emission and longer pay-back time of solar cell module.It is well known that the phosphate capacities of slags in equilibrium with liquid silicon are extremely lower. However, if we introduce another phase that possesses high ""phosphor capacity"" into the Si/slag system, one would expect to continuously remove P from Si through molten slag to the new ""phosphor capturer"". The so-called three-layer refming concept is thus proposed in the present study. Liquid Si and another liquid phase (Me) are separated by the molten slag spontaneously based on their different physicochemical properties. Two metal/slag distribution reactions are able to occur in the system simultaneously."

Jan 1, 2013

By Zhihe Dou, Yu Fang, Zimu Zhang, Yan Liu, Xiaoli Jiang Dianhua Zhang, Guanting Liu

"With the idea of “waste control by waste itself”, we come up with the crafts of using waste calcium carbide to mineralize CO2 in electrolytic aluminum waste gas, design and make out “Venturi gas-liquid-solid three stage reactor”, do experiments under the system of CO2-Ca(OH)2, investigate the influence on gas absorption by pH meter; investigate the influence on diameter distribution , rise velocity of bubble and local gas hold-up by dual conductivity probes; investigated the absorption of CO2 in every stage reactor under different initial proportion of CO2 by intelligent gas measurement system. The results showed that the reactor can fully absorb the CO2 in waste gas, and it has largely shorten the time of absorption and improve the CO2 utilization compared with the single stage reactor.The residual proportion of CO2 in the gas is below 0.08% through the absorption of three stage reactor,which show that absorption is extremely improved.IntroductionCarbide slag is a kind of polluting hydrolysis reaction byproducts in producing carbide in wet reactor, and it is mainly comprised by Ca(OH)2, It's estimated that there are about million tons carbide slag are piled up per year. Carbide slag is a kind of industrial wastes that hard to deal with ,which are treated by land filled in the past. It would not only occupy a lot of land, but also lead to secondary pollution [1].CO2 is the main greenhouse gas by now. In 2010, global CO2 emission has reached 33.5 billion tons, while China has now become the world's second largest emitter of CO2, emissions accounting for about one-seventh of the world [2].As the experts estimates, the greenhouse gas emission of whole nonferrous metal industry may over 0.6 billion tons per year, while CO2 emission of electrolytic aluminum is 0.334 billion tons per year [3]. So it is necessary and pressing to discover the reusing CO2 of electrolytic aluminum. With the idea of “waste control by waste itself”, we came up with the crafts of using carbide slag to mineralize the CO2 in electrolytic aluminum waste gas, which was experimented on the counterflow-three stage-venturi reactor,and studied the local gas holdup, residual concentration of CO2 and the volumetric transfer coefficient in the reactor."

Jan 1, 2014

By Jochen Petersen

Design and operation of heap leach processes are still largely based on,operator experience and rule of thumb. Although considered a low-cost, low-tech route for mineral extraction, the underlying physical, chemical and biological processes are actually rather complex. Numerous heap leach models have been devised over time, but the majority of these tend to simplify the true process and are of limited use in practise. The modelling approach presented here combines the more conventional reaction-diffusion model with models accounting for equilibrium reactions in solution, bacterial growth kinetics, complex reactions schemes, gas flow, heat conservation, etc. One particular model application is discussed in the context of developing a novel high temperature heap leach processes using thermophile micro-organisms. The complexity of processes such as this can only be appreciated with the aid of a systematic model. For the designing engineer an accessible, personal computer based model should be an indispensable tool for the design and optimisation of efficient heap leach operations.

Jan 1, 2002

By Bret Boster

Facilities at Amax Gold's Sleeper Mine process some 330 kt of high grade ore and 4100 kt of low grade ore annually to produce 6.8 t of gold and 7.8 t of silver. High grade ore is processed in a conventional milling facility employing gravity concentration, CIC and CIP unit operations for gold and silver recovery. Low grade ore is processed using heap leaching and carbon adsorption methods.. Presented are the evolution and descriptions of the Sleeper processing facilities and discussions of selected' operating results.

Jan 1, 1989

By Musa Karakus

Zirconia-based refractorics arc finding increasing use for specialized applications in steelmaking technology, making optimization of their resistance to corrosion by steelmaking slags more important. Samples of calcia- and magnesia-stabilized zirconia refractories have been exposed to slags in the CaO - FeO - SiO, system at 155WC for the purposes of measuring corrosion rates. Examination by SEM/EDX and cathodoluminescence of the mineralogy of the attacked specimens reveals important clues about the mechanism of attack.

Jan 1, 1992

By E. Fockedey

he destruction of free cyanide on a Co3O4 doped carbon felt was studied. The experiments were done with an eiectrochemical filter press cell on dilute alkaline solutions containing 250 mg/l NaCN. No chloride ions were added to the solutions. The cobalt oxide protects the felt against corrosion and has a catalytic effect on the degradation of the cyanide. This kind of electrode allows working with current density as high as 1200 Aim without any visible degradation of the felt. The most interesting results were obtained with a current density of 400 Aim' at which the cyanide concentration can be lowered to 5 mg/l with a current efficiency of more than 70 % and a specific energy consumption of about 10 kWh/ kg CN.

Jan 1, 1998

By A. Rios

ENAMl's Paipote Smelter commenced operations in 1951. At present, it processes 230,000 tonnes/year of green feed in a conventional smelter, which comprises one reverberatory furnace, two Hoboken, one Peirce-Smith converters and one rotary anode furnace. The feed is composed of 83% copper concentrate and 17% metallic copper precipitates, which results in a feed average grade of 32% of copper content. The final products are 75,000 tonnes/year of copper anodes and 48,000 tonnes/year of sulphuric acid. At present, the plant is undergoing a modernization to expand the smelter capacity to 300,000 tonnes/year of green feed and increase the sulphuric acid production to 100,000 tonnes/year. This will be achieved with the installation of an El Teniente Converter and an expansion in the acid plant. The work began in November 1991 and is scheduled to be in operaton by March 1993. The paper provides an overview of the modernization plans and results achieved to-date.

Jan 1, 1993

By J. C. Agarwal

Slags produced by modern smelting furnaces contain copper values which are unacceptably high for discard. The electric arc furnace is employed commercially to clean copper from flash furnace slags but the addition of highly oxidized converter slags to an electric furnace has created operational problems. Highly oxidized Noranda Reactor slags have not been processed successfully in a pyrometallurgical process. These slags, which contain large concentrations of copper (5 to 10 per cent), are treated in slag concentrators (controlled cooling, crushing and milling, and flotation) which produce a copper concentrate that must be resmelted. Though commercially operable, it will be shown that the slag concentrator has important process and cost disadvantages as compared to a pyrometallurgical process. In this paper an economic comparison is made between a pyrometallurgical process and the slag concentrator. For the analysis, five hypothetical smelting plants are considered. Each plant treats 1200 tons of copper concentrate per day and produces 109,000 tons of copper annually. The plant configurations used in this study are:

Jan 1, 1976

By Zdzistaw MiGzkowski

At KGHM Polska Miedi S.A. a direct flash smelting process is used for smelting of chalcocite concentrate for the production of blister copper. The paper presents a model of complex oxidation process of single concentrate grains smelted at KGHM. The description covers main chemical reactions, phenomena of heat and mass ex-change inside the grains and between a grain and the surrounding space. In the model, two zones describing the course of process inside the grain were distinguished: ? The first one, which moves faster towards the centre of a grain, both organic and carbonate carbon are freed. The process takes place without the presence of oxygen and results in an increase of the temperature in the core of the particle. ? The second zone moves slower into the grain and the rate of the movement is deter-mined by the presence of oxygen. In that zone the sulphur is eliminated and the oxidation of the organic compounds vapours moving from deeper layers of a grain takes place. Based on the results of laboratory tests, the coefficients that describe the oxygen transportation into the grain and decide the progress in the chemical reaction were determined. The paper contains the results of model calculations for single grains reacting in environment of various content of oxygen as well as the results of model calculations for the laboratory reactor system.

Jan 1, 2003

The U.S. Bureau of Mines investigated CaF2-assisted H2SO4 leaching to extract Mn from domestic silicate manganese resources. A pyroxmangite ((Mn,Fe)Sio3) ore containing, in pct, 34 Mn, 23 Si, 3 Ca, and 1 Fe was leached at 90° C for 3 h in a solution containing, in g/L, 12 Mn, 140 H2SO4, 130 (NH4)2SO4, and 5 CaFz. Manganese extraction of 92 pct was achieved. Manganese of greater than 99 pct purity was prepared by electrolyzing the purified pregnant solution at a current density of 50 mA/cm2. The current efficiency was 65 pct.

Jan 1, 1991

By Carlos A. Nunes

V-AI alloys have been used commercially to produce pure vanadium by Electron Beam Melting (EBM), as well as to obtain Ti-based alloys (ex. Ti-6AI-4V). The aluminothermic reduction of vanadium pentoxide (V205) is the primary method to obtain these alloys. Concerning the obtention of pure vanadium, earlier studies have indicated alloys presenting Al content between 10 and 15wt% as the most suitable alloys for direct EBM. In the present work we investigated the aluminothermic reduction of V205 in order to define process parameters for the obtention of V-AI alloys with composition in the previously mentioned range. It was studied basically the effect of excess AI, CaO addition and reaction atmosphere (air, argon) on the alloy composition (AI, 0, N). In addition, microstructural analysis of selected alloys by SEM (BSE images) and EPMA (WDX) were also performed.

Jan 1, 1996

By Liu Chunpeng

The new technological process developed is by means of thermal plasma arc smelting to obtain high grade Ni matte directly from Ni-Cu concentrates containing 6-7% nickel and 3-8% sulfur. In comparising with conventional smelting and converting processes the plasma arc smelting process has many advantages over conventional processes, such as lower energy consumption, lower capital investment and free from SO, pollution by transforming the sulfides into elemental sulfur with microwave irradiation under controlled oxygen potential, moreover, the process is simple and easily controlled due to less magnetite troubles in the operation. Therefore, this new technological process can be used as an alternative way to conventional process for Ni-Cu concentrate smelting. The main economical technical index is summarized in Tabal 1. Table 1 Main Ecnomic-technical Index

Jan 1, 1993

By Masahiro Sasaki, Wu Kepeng, Chang-Yong. Kang, Kohji Okada, Naohiro Igata, Kazuya Miyahara

"The damping capacity of the Fe-12 mass % Cr-6 to 30 mass % Mn alloys has been investigated. Particularly the effects of microstrucutre composed of the phases of a , a ' , y , and e on the damping capacity have been clarified. Various fraction of these phases were formed depending on the Mn content and cold work degree. The combination of 22 mass % Mn and 50% cold rolling formed the largest volume fraction of e martensite and showed the highest damping capacity. The other phases of a, a' and y had very small effect on the increasing of damping capacity.IntroductionFe-Mn alloys are known to be one of the high damping capacity materials [l-3]. In the present research, the damping capacity of the Fe-12 mass % Cr-6 to 30 mass % Mn alloys, in which 12% Cr is added for the improvement of corrosion resistance of the Fe-Mn alloys, has been investigated. Particularly the effects of microstrucutre composed of various phases of a (bee), a ' (bet martensite), y (fee), and e (hcp martensite) on the damping capacity have been clarified. The results of preliminary research on Fe-Cr-Mn alloys are reported by Igata et al. [4] Various volume fraction of these phases were formed depending on the Mn content and cold work degree. The combination of 22 % Mn and 50% cold rolling formed the largest fraction of e martensite and the measurement indicated clearly that e martensite had the largest effect on the damping capacity. The other phases of a ' y and a I had very small effect on the increasing of damping capacity."

Jan 1, 2000

By S. S. Chabot, S. E. James

A recent survey of CEOs from major steel companies worldwide revealed the importance of recycling zinc units from EAF dust, mill scale, blast furnace dust, and other zinc containing streams in their plants. Many processes were developed and installed in response to this challenge. The most successful approach involves the production of a crude zinc oxide and selling it to primary zinc producers to recover the metal value. The problem with this process is the high concentration of halides in the crude oxide. This type of material cannot be processed directly in an electrolytic zinc plant because of corrosion problems it will cause in electrolysis. In 1999, BRZ installed a zinc oxide receiving and washing plant to minimize the impact of halides to its circuit. A description of the washing plant and initial operating results are included.

Jan 1, 2000

By Wayne C. Stewart

Freezing of high pressure air lines and pneumatic equipment has been a recurring problem in the Thompson Smelter. The particular severity during the winter of 1989-90 resulted in costly process disruptions and repairs. A process improvement team with representatives from operations, engineering and both maintenance supervision and the shop floor was established to develop solutions. Their mandate included process evaluation, design, equipment and in-plant commissioning. In 1990, upon recommendation of the team, we installed three Refrigerant/Desiccant air dryers with a total capacity of 20,000 S.C.F.M. to service the Smelter. This paper discusses processes and process improvements associated with this installation.

Jan 1, 1993

By Anat Deepatana

Bioleaching of nickel laterite ores is the extraction technology based on the use of heterotrophic micro-organisms and their organic acid products to dissolve metals from oxide minerals. This study examined the chemical leaching kinetics of limonite and nontronite ores with metabolites including citric, lactic and malic acids. The leaching process was found to follow the chemically controlled model. The leaching kinetics was found to be significantly influenced by the acid strength or dissociation of acids in solution. Although increasing the acid strength increased the rates of leaching, this trend was not indefinite. An optimal acid concentration that defined the fastest leaching rates was identified for each acid. The amenabilities of the minerals hosting the nickel and cobalt in limonite and nontronite to organic acid leaching were also established.

Jan 1, 2006

By Ruixiang Wang, Jinhui Li, Youjun Xiao, Daoling Xiong, Hao Chen

"Leaching solution prepared from spent battery materials contains large quantities of valuable metals, such as Cu, Ni, Co, Mn and Fe. Therefore, recovery of valuable metals from acidic polymetallic aqueous solutions is of great importance for every plant. In this work, a method is introduced of recovery of Ni, Co and Mn from polymetallic solution prepared by leaching spent battery material. The basic concept includes copper was removed through replacement by iron powder followed by iron precipitation in goethite method. The experimental results show that Cu can be removed 99% at least through replacement by Fe powder, and the removal of Fe can achieve 99% by goethite method. At the same time, the loss of Ni, Co and Mn are about 2%, 3 % and 2%, respectively. The process of differential removal of metals can be selected as the treatment alternative that combines simplicity, efficiency and reliability with low capital and maintenance costs. The purified solution which only contains Ni, Co and Mn can be used to prepare NixCoyMnz ternary system precursor.1 IntroductionNickel and Cobalt are very important metals which are applied in many fields, such as energy material and support material for some new material field. The world demands for such metals is progressively increasing, while raw resources are being depleted and with the constraints raised by the Law and related legislation assigned to protect the environment from hazardous wastes in the world. Nowadays study on reutilization of waste materials has great significance for achieving secondary resources recycling and preventing environmental pollution. There are many hydrometallurgy methods applied for dealing with these wastes, while they usually contain large quantities of valuable metals, such as Cu, Co, Mn and Ni, as well as impurities, such as Fe, Zn, and etc. Therefore, proper treatment of these leaching solutions prior to their discharge is of great importance, so that the contained valuable metals can be recovered.Separation and extraction of metals from leaching solution can use some methods through solvent extraction[l,2], ion exchange[3,4], precipitation with sulfide[ 5] or alkali[ 6] and electrolytic recovery[?]. Among the appropriate treatment alternatives, replacement and differential precipitation is the most attractive treatment that combines simplicity, efficiency and reliability with low capital and maintenance costs."

Jan 1, 2011

By Mônica Suede Santos Silva

This work describes characterization of the performance of the tundish of a six strand continuous casting unit of the Companhia Siderúrgica Belgo Mineira, João Monlevade, Brazil using physical modeling. Permanent and transient conditions, due to ladle metal composition changes are considered. Pulse and step tracer addition techniques are employed to assess the control variables. For transient conditions the degree of inter-mixing and the minimum residence time are determined with a view to optimize the process especially during the grade changes of steel.

Jan 1, 2003

By George H. Edwards

Most cullets consumed in large-volume glass manufacturing processes receive little processing beyond crushing. But lead-glass cullets for specialty glasses such as industrial lighting refractors or cathode-ray tubes are combined with metals and various coatings that prohibit their direct recycling into the glass-melting processes that created them. In many cases, the contained lead renders these cullets hazardous. At present, virtually all industrial processes to separate one cullet from another depend on hand sorting, and thus are necessarily costly per unit weight. Lead-glass cullets of differing lead content are of interest because they offer the possibility of separating one glass composition from another by high-speed, automated processes at low cost. A potential process for comminution, cleaning, and separation of lead-glass cullets would involve primary and secondary crushing, magnetic and other metals separation, attrition scrubbing in water, separation of glass types by gravity techniques, drying if necessary, sampling, and preparation for transport to the point of use. Process water would be filtered to remove finely divided coating materials and glass, and reused. If carried out on a scale similar to a specialty industrial mineral processing plant, the cost per unit weight of such processing should be substantially less than the raw material value of the cullet in specialty glass production. The added value of avoiding waste disposal costs makes this process economically attractive.

Jan 1, 1994