Search Documents

By Andrey Dmitriev

The solution of set of equations for the bottom zone presented by a condition of a thermodynamic equilibrium, namely, an equilibrium constant of wustite reduction by carbon oxide, material and thermal the balances, supplemented by the equation of the heat balance for the top zone, allows to calculate the base indices of blast furnace smelting. The calculated indices are extreme accessible at the given parameters of charge and blast. Application of actual degrees of the use of gas instead of equilibrium allows the calculations of actual indices of the blast furnace smelting process.

Jan 1, 2006

By L. L. Ludwig, S. E. James, B. L. Motycka

Significant modifications to the electrolytic zinc plant operated by Big River Zinc Corporation were made at the end of the 1990's resulting in increased capacity and improved efficiencies. A new cell room, with the innovative use of acid-resistant concrete cells and a modern ventilation system, was installed to raise the capacity from 80,000 tonne/y to 106,000 tonne/y of finished zinc. Improvements to the leaching section include the conversion from a single to a two-step process, with associated equipment changes, to improve the quality of the residues produced. Another key change is the construction of a facility to allow the use of zinc oxides from secondary sources as a feed to the plant. This paper describes these improvements and the current operations.

Jan 1, 2000

By Jafar Safarian

Bauxite is the main raw material used for the production of alumina (Al2O3) through the well-known commercial Bayer process. This process has significant challenges such as limitation in using low-grade bauxites as they contain significant amounts of impurities such as Fe, Si, Ti. The Bayer process residue, which is known as red mud, is also a global environmental challenge due to huge amount of this low value residue production. An alternative sustainable process with high potential to solve these problems and produce valuable and consumable by-products is a pyrometallurgical-hydrometallurgical process in which the low-grade bauxite ore is treated through a smelting-reduction process, yielding iron alloys and a calcium-aluminate slag. Alumina is then produced from the slag by hydrometallurgical treatment. In the present work, the reduction of pellets produced from different bauxite ores by hydrogen is studied and it is shown that complete iron oxides reduction is possible. Further smelting and smelting-aluminothermic reduction of the reduced pellets show that iron and silicon ferroalloys can be produced, in addition to a proper slag for alumina extraction.

By Takeshi Yoshikawa, Kazuki Morita, Yuichi Kato

"A composite composed of carbon fiber and a Cu-Si alloy is a promising candidate for next generation brake disc materials used in high-speed trains. The composite can be prepared by vacuum infiltration of the Cu-Si alloy into the fibrous carbon matrix. The activity of Si in the alloy plays an important role in controlling the formation of SiC; this formation is attributed to the reaction between the Si in the alloy and the carbon fiber during the infiltration process. Because Fe has strong affinity with Si, the addition of Fe is expected to decrease the activity of Si in the alloy. In the present work, the variation in the activity of Si in the alloy with the addition of Fe has been investigated by equilibrating a Cu-Fe-Si alloy with solid SiO2 and graphite under controlled CO partial pressure. The first-order and second-order interaction parameter of Fe on Si in molten Cu was determined to be -16 and 160, respectively. The negative value of the first-order interaction parameter clarified the addition of Fe to the Cu-Si alloy is effective in decreasing the activity of Si in the alloy.IntroductionIron-based materials have been commonly used for brake discs in high-speed trains. It becomes critical for brake disc materials to withstand high thermal loads with an increase in the maximum speed of high-speed trains. The fabrication of high heat-resistant, light-weight brake disc materials is then crucial for their use in next-generation high-speed trains. Carbon fiber is known to be a light-weight, high-strength material, and is considered to be a promising matrix material for use in brake discs. The Cu-Si alloy exhibits high thermal conductivity. The composite in which the Cu-Si alloy is added to the carbon fiber matrix is expected to be a high performance material for brake discs. The composite can be prepared by the infiltration of the Cu-Si alloy into the carbon fiber matrix at a temperature higher than 1700 K."

Jan 1, 2012

By G. Johnston, J. Greenly, R. G. Buchheit, D. C. McIntyre, R. Muenchausen, D. J. Rej, R W. Stinnett

"Rapid thermal treatment of materials using high energy, high flux, pulsed ion beams can produce modified surface layers with unique microstrutures and properties. High energy ions loose their energy during the slowing down process in the workpiece and thus deposit their energy continuously over a depth of a few microns. The deposition of energy can lead to melting and in some causes ablation of the heated layer. Because the pulse duration of the ion beams is typically only 50-200 ns, steep thermal gradients generated during heating facilitate rapid cooling (107K/sec-108K/sec) of the treated layer by thermal diffusion into the underlying material. Rapid heating and cooling of materials can generate surface layers with non-equilibrium amorphous or nano-crystalline microstructures that exhibit increased hardness, wear resistance, and corrosion resistance. Pulsed ion beam treatment can also lead to surface smoothening or can be used to mix thin « 1 11m thick) coatings into underlying substrates. Pulsed ion beams can be generated using existing ""flashover"" ion source technology which is capable of producing single shot, mixed C, H, and O ion beams with beam cross sections of approximately 100 cm2 and energy fluxes up to 100 J/ cm2. Recent advances in repetitive high energy pulsed power technology and development of magnetically confined anode plasma ion sources have facilitated the development of ion beam systems that generate single species beams that pulse continuously at 120 shots/second. These capabilities will allow rapid treatment of large surface area workpieces at low cost.IntroductionThe rapid solidification of liquid materials can create unique materials and material microstructures that often have properties that can lead to enhanced performance. Rapid solidification processing of the surfaces of materials using continuous and pulsed laser beams (laser glazing) has been explored for over 20 years (1-5). Advances in high energy, pulsed electron and ion beam technologies over the past decade have provided rapid thermal treatment techniques that may be less expensive to impliment than laser surface treatment for many surface modification applications (6). High energy pulsed ion beams have recently been used to harden aluminum(7), copper(8) and tool steel surfaces (6,9), increase corrosion resistance of Al alloys (6), mix coatings into underlying substrates (10), and create amorphous films (11,12)."

Jan 1, 1994

By George Nekoksa

The biofilm activity monitoring probes measure applied current during intermittent short-term polarization of the probe electrodes and current or potential between the electrodes after removal of the polarization. The probe polarization mimics conditions at crevices, welds and inclusions where the biofilm activity and microbially influenced corrosion usually concentrate. Monitoring of AC resistance between the probe electrodes can provide infornation about the thickness of deposits.

Jan 1, 1994

By S. Agatzini-Leonardou

The objective of this work was to prove repeated loading capacities and investigate the selectivity of physically stabilized algal biomass from Spirulina platensis and Chlorella sp. for the removal and recovery of cobalt, nickel and chromium from laterite heap leach liquors. The testwork was carried out on a bench scale in small glass columns and proved that it was possible to immobilize the biomass on the highly porous surface of pumice stone (kissiris). Nickel and cobalt could be removed from pure aqueous solutions of each metal by the immobilized cyanobacterial biomass. Nickel and also cobalt biosorption was sensitive to the initial solution pH. Cobalt recoveries up to 80% were achieved after 5 loading cycles, from low concentration solutions, at pH 6.0. Nickel removal was complete under the same conditions, whereas chromium sorption was ineffective. Desorption of the metal loaded columns was effected by dilute sulfuric acid. The algal species giving the best adsorption capacities for the metals under consideration was selected for further experimental work with real laterite heap leach solution produced by column leaching. A statistical analysis of all obtained results was conducted using the fraction of metal removed as response. The ratio "mass of metal removed to mass of protein contained in the immobilized cells" was determined as well. The described method might be applicable for recovery of cobalt and nickel from diluted laterite heap leach solutions, such as heap wash waters, or for their removal from waste streams of a hydrometallurgical extraction process.

Jan 1, 1997

By D. G. Hattingh, A Els-Botes

"Considerable information is available on the factors influencing the iron-zinc reaction rate at 450° C of low carbon steels, in comparison there is a scarcity _of similar fundamental information of spheroidal graphite irons. This can be attributed to the more complex microstructure and ferrous alloy chemical analysis of spheroidal graphite irons. Hot-dip galvanizers have identified the complexity in controlling and predicting the thickness of the galvanized coating formed on commercial cast irons, which has serious financial implications for both the galvanizer and customer.Commercial hot-dip galvanizing has been in use for over 160 years and yet an elementary understanding of the dynamics associated with the hot-dip galvanizing of spheroidal graphite cast iron is still insufficient. To allow the. process to become a modem surface engineering technology, the fundamental aspects of the process must be thoroughly understood.When a clean iron or steel article is dipped into the molten zinc, zinc initially solidifies around the steel or iron. As heat is transferred to the article form the bath, this initial solidified zinc layer remelts and a series of iron-zinc alloy is formed by the reaction of the zinc with the surface of the article; on removal from the bath, some of the molten zinc is taken out on top of the alloy layers. At normal galvanizing temperature (450 °C), the reaction between iron and zinc is usually parabolic with time. The rate of reaction is rapid at first but then slows down and the coating thickness does not increase greatly if the article is immersed in the bath for longer times(1)."

Jan 1, 2000

By T. Ueno

Naoshima Smelter & Refinery of Mitsubishi Materials Crop. commissioned a new Mitsubishi continuous copper smelter in May 1991. Process offgas volume of the conventional reverberatory furnace line, one of the previous smelters having been shut down, was very large and thus two acid plants had been operated. It was expected that the offgas volume would, be reduced at the new smelter to about a half of the sum of those from previous two smelters and the sulfur dioxide strength would be increased. So various alternatives were studied to minimize the operation cost. And it was decided to utilize both of the plants with minor modifications by diluting the gas either with air or with dilute gases. The acid plants now receive off gases from the new copper smelter, a sintering machine of a lead smelter and a decomposer of waste acid. The paper discusses plant design, operation, improvements and modifications realized in relation with the retrofitting of the copper smelter.

Jan 1, 1992

By E. V. Verhoef

The proposed EU directive on the restriction of the use of certain hazardous substances in electrical and electronic equipment promotes the substitution of lead in consumer electronics to reduce emissions from lead in the end of life phase. In this paper, the consequences of substituting lead in solders is assessed using the Eco-lndicator-99 method for the examples. The base metal production system is considered as an interconnected network modeled dynamically in Simulink 4 and Matlab 6 (Mathworks Inc 2000), where the recovery and production of metal components of the assessed product partially overlap. This approach requires global modeling of metal production processes and mass balances and resulting allocation choices. It also reveals the susceptibility of LeA scores to different choices in the modeling and data availability and uncertainty. Besides the comparison between lead-free and lead-containing solders, other side effects are revealed. Lead is carrier material for the recycling and production of many co-elements in the interconnected production and recovery system. Substitution may have adverse effects such as temporary shortages of other connected metals that are often not considered in normal LeA assessments, thus leading to erroneous results. The suggested approach provides directions for including these external effects and for further assessment of the environmental effects of substituting lead. This paper shows that in order to assess the environmental aspects of metallurgy, dynamic modeling of the total system is required based on the fundamental thermodynamics in each metallurgical reactor, the basis of this dynamic model. With this the true environmental impact of metallurgy can be explained. In the case of lead free solder, it is shown that the mining of substitutes has a very much larger impact.

Jan 1, 2003

By Dean David

The evaluation of a new mineral sands prospect with unusual characteristics is described, The heavy minerals are very fine grained, have comparatively low average specific gravity (3.6) and are altered. Poor performance by conventional processing techniques made it necessary to trace the response of the major minerals during the separation processes, QEM*SEM® was used to quantify mineral volumetric abundances and mineral locking in magnetic and gravity separation products.

Jan 1, 1989

By Moelans. N.

A method using an ex-situ electrochemical measurement device was developed to determine the oxygen potential of non-ferrous metallurgical slags. The electrochemical cell consists of the molten slag sample, an inert Ir electrode, a stabilized Zr02 solid electrolyte and a NilNiO reference electrode. Different slags from non-ferrous pyrometallurgical processes were analysed at I 100 and 1200 °C and pO2values between 10-3 and 10-12 bar were obtained. The measurements were evaluated with thermodynamic calculations and using processing considerations. It was found that the reproducibility and stability of the measurement was significantly improved by shielding the molten slag from the atmosphere by a thin layer of carbon, especially for slags with a low oxygen potential.

Jan 1, 2003

By Daniel Chen, Jewel Andrew Gomes, Venkata Palla, Sadia Afrin Jame, David Cocke, Paul Bemazzani

"Textile industries use various kinds of chemicals including dyestuffs and pigments during dyeing and finishing processes. The effluent from these processes includes suspended particles, strong color, high pH and high chemical oxygen demand (COD) that are extremely toxic and make environmental hazard. Although physical, chemical, photochemical, and biological methods are available for treating such wastewater, the electrochemical technique, electrocoagulation (EC), has emerged as an efficient, simple, and cost-effective technology in the last few decades. In this study we present the applicability of EC technique for removing dye, such as direct red dye using iron electrodes, and the optimized conditions such as dye concentration, current density and pH. The degradation of dye molecules was investigated using UV-visible spectroscopy. The EC-floe was also characterized using SEM/EDS, XRD and FTIR.IntroductionWastewaters generated by textile industries contain large amounts of toxic aromatic compounds, especially azo dyes. Azo dyes and their degradation products, such as aromatic amines, are highly carcinogenic. These effluents are also responsible for causing high levels of color. The colored wastewater released into the environment is also a source for disruption of aquatic life and aesthetic pollution as well [1].In most textile industries, dyeing and finishing are the two important processes which are generally applied. These two common processes generate significant amount of wastewater, which may contain, suspended particles, high pH, strong color and high chemical oxygen demand (COD) concentration [2]. Low pH and high temperature are other polluting factors from the waste water. Textile industries make use of about 10,000 dyes and pigments [3]. Disposal of these colored wastewaters poses a major problem for the industries as well as a threat to the environment. In textile industries, because of the low efficiency (60-90%) of dye fixing on textile fibers, substantial amounts of unfixed dyes are released in waste waters. The conventional method for treatment of textile wastewater was a combination of biological, physical and chemical methods [2]."

Jan 1, 2011

By Ying Li, Xuling Chen, Xiaohui Fan

"In the sintering process, the behavior and performance of iron ores is extremely complex. Different minerals have different sintering properties. In order to use iron ores rationally and effectively, multilevel fuzzy evaluation method is used to establish the comprehensive evaluation model of iron ores. Because of the relative independent characters of iron ores in sintering process, the characters can be divided into physical and chemical properties, granulation performance, and sintering properties, are divided, and together with iron ores prices as the first level index for judging, which are used as the second level index for judging. Using the analytic hierarchy process (AHP) to determine the weight of each index, which is used as the second level index. The relative membership matrix is determined by triangular membership function, the comprehensive evaluation model is established.IntroductionIn China, sintering is the main method for iron ores agglomeration. Sinter accounts for more than 80% of the blast furnace. Sinter production in the iron and steel enterprises in China plays an important role[l-2]. As the main raw material of iron ores sintering, the objectivity and integration of iron ores evaluation is essential. The iron ores evaluation methods include of metric ton price evaluation method, iron grade of a single iron ores sintering, acid-base balance method, composition assessment method and other methods which are based on the chemical composition and physical properties of iron ores to measure the quality of iron ores[3]. The high-temperature mineralization is an important process in sintering process, which affects the structure and mineral composition of the sinter, and has a close relationship with the quality of the sinter[ 4]. Therefore, in consideration of the physical and chemical properties, granulation properties, mineralization performance and sintering properties, the iron ores are evaluated by multi-level fuzzy comprehensive evaluation. The multi-level fuzzy comprehensive evaluation method makes a comprehensive evaluation, applying fuzzy transform principle and maximum membership degree principle, considering a number of factors related to the things which are evaluated. The method has lower requirements for the amount of data, and which integrates qualitative with quantitative judgment. It has a unique advantage to make up for the deficiencies of traditional evaluation methods. It also can comprehensively evaluate the iron ores in a relatively short period, reduce a lot of experiments, improve efficiency and guide the sinter production[5-6]."

Jan 1, 2013

By Jung-Ah Kim

Precipitated Calcium Carbonate (PCC) is obtained through calcination, hydration, and carbonation. Thus, the change in each process condition determines the particle size or morphology of PCC. To date, studies on precipitated calcium carbonate have mainly focused on process manufacturing PCC, aimed matter. Still, few studies on calcination or hydration have been conducted. Therefore, this study sought to investigate the effect of hydration condition on the synthesis characteristics of aragonite PCC. Results showed that the particle size of calcium hydroxide changed based on the variation of the initial hydration temperature. In particular, higher initial temperature resulted in the larger particle size of calcium hydroxide used in synthesis. The particle size and yield of aragonite also increased when calcium hydroxide made at high temperature was used. The water/solid ratio or total amount at the hydration time had no effect on the manufacturing process of aragonite, however.

Jan 1, 2006

By D. Donald Downey

Pilot Testing Ion Exchange Resin (IEX) can go from very simple beaker testing to complicated column testing. Space velocities, regenerant quantities, loading capacities, ion leakage, are all terms that get accumulated together to prove or disprove a resin’s (or resins’) ability to load a single ion (or specific set of ions). Not getting all the resin’s operating parameters correct will disqualify (or at least skew) the results. Laboratory tests for capacity, moisture content, bead size, metals fouling, etc.—what does it all mean? At last count, there were over twenty-five separate ion exchange resin tests (analyses) that were available to end users. Standard testing procedures identify the resin properties but more specific procedures can be used to identify problems with equipment operation. Then, there are the costs to consider; simple cation resin testing (moisture content, total capacity and bead integrity) is in the $200/sample range. However, add to this Chatillon, Russian Ball Mill Test, HIAC particle size, metals and % regeneration test procedures and the lab work can increase to over $1000/sample. In this paper, the author will explain the “must-do” pilot and test procedures and why they are important and the key to understanding how resin performs ion exchange.

By J. R. Donald

Surface and interfacial phenomena play a significant role in refractory performance. For example, the wettability of the refractory material with slag, matte, and metal influences infiltration and interfacial reactions. Yet, very little fundamental information regarding the surface properties of refractory materials and slag is available. Thus, in the present work, the sessile drop technique incorporating a high temperature furnace equipped with X-ray fluorescope was employed to investigate the surface and interfacial phenomena of fayalite-type slags on solid alumina at 1200?C. The iron to silica (Fe/SiO,) ratios employed were 1.4 and 2.0, and the oxygen potentials used were log p02 =-11 and log p02=-9 atmospheres. The contact angle between the fayalite-type slags and the alumina were determined to be relatively low, at about 16.9 to 19.6 degrees under the experimental conditions. The surface tension of fayalite slag (Fe/SiO2=1.4) at an oxygen potential of log -11 was 0.298, which agreed with the work of previous researchers. The surface tension of the fayalite was observed to increase with time. The spinel FeAl2O4. was determined to be the product of the interfacial reaction, and 8.8 to 15.8 mass percent alumina was dissolved into the slag after 40 minutes.

Jan 1, 1996

By M. E. Karabin, R. J. O'Malley

"A mathematical model of the roll casting process has been developed which predicts macro-variables, such as roll separating force, roll torque, and strip exit speed for a range of roll speeds. Continuum variables, such as interface pressure, interface shear stress, freeze-front shape, and internal temperature distribution are also predicted.The model consists of two independent segments: solidification and rolling. The solidification model is two-dimensional (thickness and rolling direction) and is capable of handling alloy solidification. The solidification model is employed until solidification through the thickness is complete, then the rolling solution is activated.The rolling model is a one-dimensional (rolling direction) mechanical solution based on the von Karman approach, coupled with a two-dimensional thermal solution. The flow stress is expressed as a function of the average through-thickness temperature of the strip.Experiments were performed using a laboratory roll caster to test and refine the model. Experimental strip exit temperatures were used as input to the model. Experimental and predicted roll torque and strip exit speea were forced into agreement at a single reference roll speed to obtain values for the coefficient of friction and the interfacial heat transfer coefficient. Using these values, good agreement was obtained between predicted and experimental torque and strip exit speed over the entire range of roll speeds examined."

Jan 1, 1986

By P. A. Metz

The Fairbanks mining district has produced in excess of 7.5 million troy ounces of placer gold and 250,000 troy ounces of lode gold since gold was discovered in the area in 1902. The Fairbanks mining district is in the northwestern part of the Yukon-Tanana Upland Schist Terrane, an area of approximately 240,000 square km that has produced in excess of 21 million troy ounces of placer gold. All lode gold production from the terrane has been from the Fairbanks mining district, and all of this production has come from high-grade gold-quartz polymetallic sulfide veins. Gold grains in the vein systems range in size from several microns to several millimeters. The veins are localized in a complex metamorphic rock assemblage which includes greenstones and felsic metavolcanic and volcaniclastic rocks, meta-exhalatives and metasediments. Gold occurs in the metamorphic host rocks in association with arsenopyrite and arsenic-antimony sulfides which occur in lenses and disseminations within the host rock. Gold grains occurring in the metamorphic host rocks range. in size from sub-micron to a few microns in diameter.

Jan 1, 1987

By A. R. G. Azevedo, G. C. Xavier

"The search for technological innovations in the Civil Construction takes as an objective the reduction of costs and increase of the productivity. However, these technologies demand analysis and studies of parameters of control that provide the quality of the products. With the intention of improve the knowledge on industrialized mortars used in mechanized projection machines, a characterization was done in the state anidro, fresh and hardening of three mortars, being each one of a State, Rio de Janeiro, Sao Paulo and Bahia. The tenors of water/ mortar was obtained through tests done in built environment, it varied from 0,17 to 0,26. From these results, the mortars were projected by his respective consistency, analyzing its compressive strength, and traction adherence resistance, in this way, the good performance of the revetments was provided.IntroductionThe market competitiveness of Construction has led companies to invest in construction processes and techniques in order to rationalize and optimize the buildings. Thus, changes emerged in coating system providing improvements in conventional materials and novel construction techniques, such as mortar industrialized and mechanized projection.Adopting projection equipment mortar is flagged as one of the solutions to reduce the interference of hand labor in construction, optimizing the performance of internal and external coatings, as well as streamline the production process and transportation, reducing lossesMaterials and deadline for execution of the casing(l)The process has been used due to its benefits, however, studies are necessary parameters for quality control of these mortars used in the projection to greater knowledge of mixing and market acceptance. It is therefore quite relevant information processing techniques available on the subject, as necessary to carry out research aiming at defining specific indicators of quality."

Jan 1, 2013