Search Documents

By Collin L. Stewart

A summary of the results of a limited subsidence monitoring program at Cyprus Amax Coal Company's Shoshone Mine No. 1 in the Hanna Basin of south central Wyoming is presented. The monitoring program was designed to meet regulatory requirements for confirmation of subsidence predictions made in the mining permit. The longwall panels were 380 ft to 600-ft wide. Mining heights varied from 11 ft to 13.5 ft. Gate road development included three-entry and two-entry head and tail gates. Overburden depth varied from 150 to 945 ft. The coal seam and overburden dip at approximately 11 degrees. The overburden is very low to low strength mudstone and carbonaceous shale with low to moderate strength, silty sandstone interbeds. Panel W/h ratios varied from subcritical to supercritical. Smax was 0.9 of the mining height. The subsidence ratio was about 0.6 for subcritical width. The draw angle on the up-dip side averaged 20 deg. The draw angle on the down-dip side averaged 12 deg.

Jan 1, 1995

By Winton Gale

"The aim of this paper is to summarise the results and conclusions of Australian Coal Association Research Project (ACARP) Report Cl3013 which relate to water inflows into a mine which occur through the overburden above and adjacent to longwall panels. The study assessed available data of inflows into underground coal mines and utilised computer simulation of water flow through fracture networks. The study concluded that flow into mines is typically via an interconnected network of pre-existing and mining induced fractures. The height above the coal seam that mining induced fractures extend is typically related to the width of the panel. However the potential for those fractures to form a connected network which can facilitate flow, is related to the amount of subsidence and the depth of mining. The study compares model simulations with measured data and provides guidelines to estimate the average hydraulic conductivity of the overburden above extracted longwall panels in Australia.INTRODUCTIONWater inflow into coal mines has been a design issue for many years. Guidelines as to the potential for water inflow have been developed in many countries based on local experience and the form of mining being undertaken. In most instances, the guidelines relate to inflows which would endanger underground personnel and operations.In more recent times, water inflow criteria for mines has been widened to include lesser inflows which may not impact on mine safety or operations, but have the potential to reduce water flow within streams and surface aquifers. For the purpose of this paper the larger inflows which are readily measured in a mine or may impact on mining safety are defined as mine inflow and the lesser inflow relating to aquifer water loss as environmental inflow.The water losses referred to are those which enter the mine from the surface or from near surface aquifers.The empirical relationships developed as mine design guidelines or regulations typically relate to high flow (mine inflow) situations and in this paper, these have been reviewed as to their application to environmental inflow. In many cases environmental inflows were unlikely to have been noted or recorded in many mining operations in the past."

Jan 1, 2010

By Freddie Hunter

An underground mining method for extracting an eight metre (26') coal horizon, containing a sandstone layer. A decrease in the thickness of the rock strata between the number two and number three seams of the Sasolburg Coal Field, has resulted in a total mining horizon approximately eight metres (26') thick. This parting varies in thickness and competency and in some areas is impractical to cut with a continuous miner. In addition, the general mining area is highly jointed. The top seam is first mined to a normal bord and pillar plan with a continuous miner. The bottom seam is then mined by selectively undercutting the stone parting constituting the floor of the top seam. In areas where this parting is between 0.75 - 2.50 metres (29.5" - 98") thick, it is suspended from the primary roof support installed when mining the top seam. Secondary, high extraction retreat mining is then undertaken in the coal pillars adjacent to the suspension supported headings in the bottom seam. Left in-situ, the parting provides lateral support to the pillar sidewalls in both the top and bottom seams, enabling high percentage extraction rates in what was previously thought an uneconomically mineable area. The paper proposed, presents the challenges and practical implications of executing the mining method, including the primary roof control of the top seam and the stone parting between scams.

Jan 1, 2003

By Axel Preusse

On the basis of the Law on Financing Hard Coal Mining dated 28 December 2007, the subsidized German hard coal mining industry will be shut down to the end of the year 2018 in a socially acceptable manner; in 2012 this decision will be reassessed. Even after the abandonment of all mining activities subsequent burdens are inevitable. In this paper, the possible long-term effects resulting from a mining industry history, which is spanning more than 200 years, and their possible consequences are pointed out, in particular in connection with the abandonment of mine water drainage measures which is economically meaningful in the long term. According to the decision situation as it presents itself today, this point in time will be far beyond 2018. In preparation for this, an action framework is to be developed in areas possibly affected.

Jan 1, 2008

By Brian E. Perrine

Underground mining requires a variety of specialized equipment. With ever-changing mining conditions and methods, some mines have had to resort to purchasing existing industrial equipment and adapting it for underground use. Since this equipment is not made for underground mining or their specific task, the result is often lost time, money, and sometimes an unsafe working condition. One such application is the setting of a CAN. A CAN is a type of cylindrical secondary roof support made from a cement composite and encased in steel. The CAN has become popular because of its simple one-piece design that can handle heaving and sagging better than other available designs. ?Because of this exceptional ability to sustain load through extended convergence and displacement, the CAN is one of the most robust and stable standing supports in use today.?It also promotes better air flow due to the size and shape of the CAN. CAN size and weight have increased over time to handle more difficult mining conditions. Significant down time and inefficiencies with existing CAN setting machines at Twentymile Coal were directly due to the item in use not being designed to be task-specific. They were undersized with very limited movement. The miners had to take extra steps and precautions when setting CANs. Maintenance delays were significant. Twentymile Coal Company realized that they required a safer, more reliable and more efficient machine to handle and set CANs, and looked for a partner to develop a new design-specific machine. They worked jointly with J.H. Fletcher® engineering and sales to design and manufacture a machine specifically made for setting CANs. The objective was to produce a machine that would handle the conditions and methods that the mine required for setting CANs during longwall retreat. The resulting design had to be safe, stable, have a wide range of motion, be ergonomic, simple to use, and easy to maintain. The machine also had to improve efficiency. The resulting machine has been operating for approximately one year at Twentymile Coal and has been proven to improve safety, reliability, and efficiency. In conclusion, with the task-specific CAN Manipulator, the mine is able to better plan daily tasks with the knowledge that the machine will be available throughout a shift, and the employees will be safer because of the machine?s ergonomics, stability and safety. This has resulted in better productivity and a safer environment.

Jan 1, 2013

By Behdeen Oraee-Mirzamani

Tunnel stability has an important role in the production process of an underground coal mine. There are various methods for analysing tunnel stability, such as numerical methods and analytical methods. In this paper, numerical methods (Phase2 software) have been used to determine tunnel wall displacement in a mining tunnel of the Parvade underground coal mine. The Ground Reaction Curve has also been drawn using analytical methods to determine tunnel wall displacement. The comparison of results from the numerical method and the analytical method show a noteworthy difference in the tunnel wall displacement. The displacement calculated by the numerical method shows a lower value than that of the analytical method because the numerical method is more suited to modeling the various coal and rock layers, as well as the shape of the excavations found in coal mines. The methodology used in this paper together with the results obtained from both methods can serve as useful tools for the coal mine design engineer when determining the ground support requirements.

Jan 1, 2013

By S. E. Phillipson

Underground mine mapping is a critical component of understanding the controls on ground instability. Many relatively localized examples of ground failure are associated with geologic features, such as faults, joints, compaction zones, or sedimentological transition zones. In contrast, long-running, directional roof falls are associated with regionally directed horizontal stress fields, which are induced by tectonic plate interactions in the earth?s crust. When stress-related features are distinguished from geological features, underground mapping can be an effective method for inferring the direction of horizontal stress at individual mines. Comparisons with data compiled in the World Stress Map confirm that underground mapping can be a valid method for determining the orientation of maximum principal horizontal stress at a variety of scales, ranging from individual mines to an entire mining district or coal basin. Comparisons are presented between the maximum horizontal stress directions inferred by MSHA?s Roof Control Division through underground mapping and the azimuths of maximum horizontal stress in the World Stress Map database for North America?s Pennsylvanian-aged Appalachian, Illinois, Black Warrior, and Arkoma Basin coal fields. The comparison indicates that azimuths are similar for both data sets, even where variations in the direction of horizontal stress are present. It is interpreted that inconsistencies in direction are attributable to near-surface affects such as deeply incised stream valleys, or to fault zones that represent heterogeneities in the crust.

Jan 1, 2009

By Ken W. Mills

The ground movements associated with underground coal mining and, in particular, longwall mining, are recognised to include horizontal subsidence movements, but the mechanics of the processes that cause these horizontal movements are not well understood. Over the last two decades, three-dimensional subsidence monitoring has become routine in Australia and has provided a wealth of measurements of horizontal movements caused by mining subsidence. These measurements and other sub-surface observations allow the processes that cause mining-induced horizontal movements to be inferred and, subsequently, verified. In this paper, the mechanics of the processes that cause horizontal movements, particularly those in sloping topography, are described and discussed on the basis of field observations. There are several processes recognised to generate horizontal subsidence movements. In flat terrain, systematic horizontal movements cause the surface to move initially toward the newly created goaf and, subsequently, in the direction of mining. Tectonic energy stored as horizontal stress is released by mining, and, when the horizontal stresses are high, the magnitude of this horizontal stress relief movement is large enough to be perceptible for some kilometres from the panel. In sloping terrain, there is an additional component of horizontal movement that occurs in a down slope direction. This movement, sometimes referred to as valley closure movement, has a magnitude that is typically much greater than systematic or stress relief movements.

Jan 1, 2014

By Deren Zhu

The principle of roof control in longwall mining is to control main roof fractures so as to reduce roof weighting, plus reasonable and effective design of supports to reduce the convergence and premature caving of the immediate roof. This paper introduces a comprehensive test for better roof control based on the geological conditions of coal seam No. 16 in Zaozhuan Colliery, China.

Jan 1, 1990

Coal mass strength properties must be estimated to obtain realistic estimates of coal pillar strength. The limitations of existing techniques for approximating these properties are discussed. The coal mass is anisotropic. The Hoek and Brown approach to rock mass property estimation is modified to allow for this. This approach requires the Rock Mass Rating (RMR) for the strata. In the normal case where bedding is sub-horizontal, these major planes of weakness have little effect on the strength of pillars. As a result of this the RMR must be measured parallel to bedding. This means that a significantly higher rating than that usually obtained for coal is observed. The use of mass strength property estimates in extant empirical relationships is outlined. At high width to height ratios, an acceleration in the rate of increase in pillar strength with increasing width to height ratio has been observed. The empirical relationship developed by Salamon (the so called squat pillar formula) takes account of this. This relationship was found to have significant limitations with respect to its universal application. Modifications arc made to Bieniawski's empirical formula to extend its use to large width to height ratio (squat) pillars. This new squat pillar formula has none of the disadvantages associated with Salamon's relationship. Strain softening was incorporated into non-linear finite difference numerical modelling to estimate pillar strengths. The technique outlined above is used to obtain peak coal mass properties. Modelled pillar strength was found to be sensitive to both peak and post peak mass strength properties. Post peak properties were found to be difficult to obtain and required some back analysis. Modelling results were used to estimate both the strength of squat pillars and parameters for use in a now squat pillar empirical strength relationship.

Jan 1, 1992

By Lewis Martin

Spokane Research Center personnel are currently conducting research on cable bolts to assess their material and support properties, to provide design criteria for roof control systems under various types of underground mining conditions, and to provide background data for computer models of cable bolt supports. Laboratory studies of cable bolts made of conventional steel cables with Garford bulbs and collars resulted in recommendations on characteristics such as embedment length, hole diameter, cable bolt diameter, and configuration of cables. A completed series of laboratory tests has determined the minimum embedment length of resin required for resin-grouted, cable bolt ground support.

Jan 1, 1996

In recent years, improvements made to the longwall system have accelerated at a faster pace than those made to the gate entry development system. As a consequence, unless planned years ahead of time, extending the panel length is nearly impossible without some innovative approach. At Cyprus Amax Coal's Emerald mine the G panel length was extended by 3,500 ft- by developing three entries across it to facilitate development of its headgate and tailgate entries simultaneously when the adjoining F panel was in operation. After evaluating alternative supporting methods and associated risks, determination was made to backfill these entries and crosscuts using a low strength flyash cement mixture prior to mining thru. Instrumentation was also used to monitor the stress change or front abutment stress in both the coal and the backfilled material ahead of the face. Longwall mining thru these three entries took about four eight-hour shifts and proved to be very successful. The designed flyash cement mixture provided adequate roof stability and caused no difficulty in the shearer's cutting while eliminating an in-panel longwall face move and minimizing the risk of roof or floor failure in the in-panel openings, or in the worst scenario loss of the face during the longwall cutting thru. This approach provided the intended result of extending G panel and recovered about one million tons of coal. This paper summarizes the engineering design of the cutting-thru project and flyash cement mixture, front abutment stress changes within the longwall coal block, backfilled material, and coal pillars ahead of the longwall face, and our underground observations

Jan 1, 1997

By W. M. Pytel

The applicability of the beam theory in analysis of roof- pillar-weak floor interaction in partial extraction room-and-pillar mining is presented. The mine structure is modeled as an equivalent multi-indeterminate overburden elastic beam supported by elasto-plastic pillars; resting on a viscoelastic layer of immediate weak floor strata underlain by a competent rock mass. The developed analytical model was initially utilized to conduct sensitivity analyses of different variables affecting the mining system, such as the deformability of coal and weak floor strata, thickness of weak floor strata, number of pillars in a panel, width of pillars, width of panel etc. These analyses were then extended to three overburden strata - coal pillar - floor strata lithologies typical of active coal mining areas in Illinois.

Jan 1, 1989

By Peter Zhang

Pumpable cribs are being increasingly used in longwall tailgate entries and bleeders for roof support under abutment pressure. Their high peak capacity and confinement-controlled yield characteristics from reinforced-bags make them relatively safe and reliable standing supports for highly productive longwall panels. The pumpability of crib material over a long distance from the surface greatly reduces material handling and makes the underground installation more efficient and flexible. However, the performance of pumpable cribs is dependent upon crib properties, crib pattern, quality of installation, and geological and mining conditions. For proper crib selection and safe support design, it is critical to understand the basic technical requirements and performance of pumpable cribs in longwall tailgate entries and bleeders. Based on more than 10 years of experience using pumpable cribs for longwall standing support, the requirements and performance of pumpable cribs in longwall tailgate entries and bleeders under different mining conditions are presented. Experience shows that the load-displacement curve from full-scale lab testing is a good indicator of pumpable crib suitability for certain applications. Crib peak capacity, stiffness, and residual characteristics define its applicability to certain gate entries and bleeders under different cover depth. Crib pattern and spacing can be determined by abutment pressure level, roof, floor, and rib conditions, local roof stability, and ventilation requirements. To achieve proper in-situ performance, quality control of crib installation is also important.

Jan 1, 2012

By L. Mahony

This paper describes the design, construction and commissioning testing program for a laboratory facility at the School of Mining Engineering, UNSW, Australia, aimed at evaluating reinforcement tendon performance when subjected to shear loading. The project has been financially supported through the coal industry ACARP research initiative. The single failure plane design adopted in the test rig has been successful in allowing shear loading to be directly applied to fully installed (and where relevant, pre-tensioned) rock bolts. Initial results are extremely encouraging, and illustrate a significant axial component of load development as shearing takes place - particular in lower strength, softer material types. The paper also outlines future plans for use of this facility.

Jan 1, 2005

By N. P. Kripakov

Results of a complex three-seam interaction analysis in a western U.S. coal mine are presented. The physical situation simulated by the models represents the development of a set of entries underneath two previously mined seams with all three seams in proximity to each other. The layout and the geometry of the remnant pillars in the upper seams were nonuniform and not always directly superimposed over each other, creating a very challenging modeling problem. The U.S. Bureau of Mines' MULSIM/PC computer code was upgraded and enhanced to perform the required three-seam interaction calculations. Analysis was limited to simple linear-elastic assumptions as only peak stresses were required. Results clearly indicated that stress concentrations in the lower seam increased approximately 100 percent when compared to cases simulating no extraction in the two upper seams. These stress concentrations generally occurred in zones directly below points of highest abutment pressures in the upper seams. Overall, the model results compared favorably with actual documented observed behavior where roof failures were known to have occurred.

Jan 1, 1996

By Vasundhara

Underground coal mining in soft floor environments has often led to strata control problems ranging from small scale issues such as floor heave which disrupts traffic and ventilation, rib spalling and induced fractures in pillars, through to large scale instability and long term subsidence. Past investigations of the problems encountered in Newcastle Coalfields of New South Wales, Australia, have revealed that the soft floor unit comprises of claystone which is very sensitive to moisture. It is prone to swelling, reduction in stiffness and loss of strength in the presence of moisture. Long term stability of mine panels in such an environment is governed by the extent of deterioration of the floor strata. The paper reports the field investigations conducted at Cooranbong Colliery to assess the extent of softened floor zone in the roadway and under a pillar.

Jan 1, 2001

By Robert P. Kudlawiec

The use of Mobile Roof Supports (MRS) in pillar retreat mining has been a fairly recent occurrence in coal mining operations in the United States (1988). Determining the pillar block configuration, the crosscut and entry centers, the number of entries developed, the method of ventilation, and the type and mixture of equipment used arc all factors in establishing a successful pillar retreat operation. This paper will evaluate and report on the history of one coal company's relationship with MRS usage for pillar retreat mining and focus on the company's use of horizontal pillars (inverted-blocks) for the panel configuration.

Jan 1, 2000

By Guy Reed, Russell Frith, Kent Mctyer

"Coal pillar design has historically been based on assigning a design factor of safety (FoS) or stability factor (SF) to coal pillars according to their estimated strength and the assumed overburden load acting on them. Acceptable FoS VALUES (have been assigned based on past mining experience, and at least one methodology includes the determination of a statistical link between FoS and probability of failure (PoF).The role of the pillar width-to-height (w/h) ratio has long been established as having a material influence on both the strength of a coal pillar and its potential mode of failure. However, there has been significant professional disagreement on using both FoS and w/h ratio as part of a combined pillar system stability criterion, as compared to using FoS in isolation. The argument is that, as w/h ratio is intrinsic to pillar strength, which, in tum, is intrinsic to FoS, it makes no sense to include w/h ratio twice in the stability assessment. At face value, this logic is sound.However, this paper will argue that there is a valid technical reason to bring w/h ratio into system stability criteria (other than its influence on pillar strength), as it is related to the post-failure stiffness of the pillar, as measured in situ, and its interaction with overburden stiffness.When overburden stiffness is bought into pillar system stability considerations, two issues emerge. The first is the width-to-depth (W/H) ratio of the panel, in particular whether it is sub-critical or super-critical from a surface subsidence perspective. As a minimum, this directly relates to the accuracy of the pillar loading assumption of full tributary area loading. The second relates to a reevaluation of pillar FoS based on whether the pillar is in an elastic or non-elastic (i.e., post-yield) state in its as-designed condition, as relevant to maintaining overburden stiffness at the highest possible level.The significance of the model presented is the potential to maximise both reserve recovery and mining efficiencies without any discernible increase in geotechnical risk, particularly in thick seams and higher depth of cover mining situations. At a time when mining economics are, at best, marginal, removing potentially unnecessary design conservatism without negatively affecting safety is of interest to all mine operators and is an important topic for discussion amongst the geotechnical community."

Jan 1, 2016

By Gift Makusha

Pre-feasibility work at Goedehoop Colliery indicated that stooping of the undersized pillars could be undertaken safely and economically. In light of the findings a decision was taken in may 2003 to undertake the project in the 600 area where three panels (628, 630 and 632) were identified for pilot test sites. The findings of the pre-feasibility studies were presented in a paper to the 22nd International Conference on Ground Control in Mining held at Morgantown in 2003 (1). This paper is a progress report for the project 12 months down the line. Work commenced to prepare the sites for mining including, acquisition of equipment, equipping the panels, selecting and training people to undertake the project. Three monitoring sites were set up distributed evenly along panel 628. Each site comprised of a surface extensometer station in the overburden strata adjacent to a pillar underground containing hard inclusion vibrating wire extensometer cells. This combination would be used to record pillar loading ahead of stooping as well as the depth of caving and strata deformation in the goal zone behind the stooping face. In July 2003, support work began to secure the roof and rib sides. The support was required to be at least three-pillar center distances ahead of the mining front to ensure that the effective stooping zone is secured at all times. The NEVID method of pillar extraction developed at Sasol and described in detail by Ismet and Moolman (2) in a Coaltech 20-20 report was adopted for the pilot project. As part of training the selected stooping team was send for a week to Sasol's Bosmanskrans Colliery to familiarize with the NEVID method of stooping. Further training sessions were carried out on site especially on the use of Mobile Roof supports. The first cut was taken on 20 August 2003 by implementing a form of chequerbord mining taking every second row of pillars. Three rows were mined this way which period was considered training to get workers familiar with the new equipment and mining method. On the fourth row the full design span equivalent to mining 4 pillars in a row was implemented taking out all the pillars in successive rows. Production figures gradually increased from 300 to more than 1,000 tons run of mine coal per shift. Panel 628 was mined out at the end of December 2003 and the second of three panels (630) is being mined. Substantial data from the monitoring set up has been recorded since the start of the project. Monitoring will continue to the end of the pilot project and the data will be analysed and fed back into the design tools to improve the design in future undertakings. The pilot project has been a success so far and other old workings are being evaluated for stooping.

Jan 1, 2004