Search Documents

By Timothy Batchler

"Pumpable roof supports are currently being used to provide a safe working environment for longwall mining. Because different pumpable supports are visually similar and installed fundamentally in the same manner as other supports, there is a tendency to believe they all perform the same way. However, there are several design parameters that can affect their performance, including the cementitious material properties and the bag construction practices that influence the degree of confinement provided. A full understanding of the impact of these design parameters is necessary to optimize the support application and to provide a foundation for making further improvements in the support performance.This paper evaluates the impact of various support design parameters by examining full-scale performance tests conducted using the National Institute for Occupational Safety and Health (NIOSH) Mine Roof Simulator (MRS) as part of manufactures' developmental and quality control testing. These tests were analyzed to identify correlations between the support design parameters and the resulting performance. Based on more than 160 tests over 7 years, quantifiable patterns were examined to assess the correlation between the support dimensions, cementitious material type, wire pitch, and single-wall vs dual-walled bag designs to the support capacity, stiffuess, load shedding events, and yield characteristics.INTRODUCTIONDeveloped in the 1990s, the first major use of pumpable supports systems in U.S. longwall operations was in the support of bleeder entries (Barczak, Tadolini, 2008). Since then, they have been utilized as yieldable concrete supports to provide a safe working environment for longwall mining gateroads, bleeders, and emergency escapeways while also maintaining adequate ventilation pathways. The basic structure of pumpable roof supports has remained unchanged over the years. Formed in place with a twopart fast-setting grout, the support material can be pumped into a containment bag from several thousand feet away often through surface boreholes. The containment bag then acts as a form to fill the support and provides confinement to the grout during loading and after failure. Pumpable roof supports provide full contact with the mine roof and floor, which eliminates the need for secondary material to establish proper roof contact (see Figure 1). They provide a high peak load capacity and a sustained, confinement controlled yield behavior while maintaining stable ground conditions, which is essential to underground mining operations."

Jan 1, 2016

By James M. Kramer

This paper introduces an analytical approach for the determination of the vertical stress in the chain pillar system between two adjacent longwall panels. The development of this approach is based on the principles of fracture mechanics and superposition. Some empirical formulae have also been incorpomted into the development of the mathematical model. The mine entries and longwall gobs are treated as Mode I cracks in an infinite plate while the resistance of gob material and the characteristics of the pillar yield zone are considered as the distributed forces on the surface of the cracks. An user- friendly computer program has been developed to facilitate the calculation involved in this task. This approach is as accurate as the numerical analysis methods but requires much less expertise and computer hardware and software to apply

Jan 1, 1998

By Thomas M. Barczak

The decade of the 90's brought an unprecedented increase in the development of innovative technologies to provide more effective and easier to install roof support in underground mines. To facilitate the application of these technologies to improve mine safety. National Institute for Occupational Safety and Health (NIOSH) developed the Support Technology Optimization Program (STOP). STOP is a windows based software program that provides mine operators with a simple and practical tool to make engineering decisions regarding the selection and placement strategy of these various standing roof support technologies. This program includes a complete data base of the support characteristics and loading profiles obtained through safety performance testing of these supports at the NIOSH Safety Structures Testing Laboratory. Support design criteria in the form of the required support load density at a specified convergence can he established from four options: ( 1 ) a data base of measured ground reaction data from various mines or ground behavior information inputted by the user. (2) determination of loading requirements based on a detached roof block or rock failure height. or (3) criteria based on the current roof support system, and (4) arbitrary criteria set the by user. Using these design criteria, the program will determine the installation requirements for a particular support technology that will provide the necessary support load density and convergence control. Optimization routines are also available to determine the most efficient support design for a user specified support installation- In addition to these performance measures. STOP can be used to compare material handling requirements and installation costs. Comparisons among the various support technologies are easily made including graphical analysis of relevant support parameters. This paper describes the STOP and its application to optimize standing secondary roof support systems.

Jan 1, 2000

By Christopher Mark

After the United States and Australia, South Africa has the largest. modern underground coal mining industry in the world. Historically, South Africa has been the cradle of many innovations in ground control, particularly in the area of pillar design. Today, South African mines are grappling with many of the same issues faced by their U.S. counterparts, including safety during pillar retreat operations, selecting the proper roof support, and maintaining long-term pillar stability. The author recently visited seven underground mines in the Mpumalanga, Free State, and KwaZulu-Natal provinces. Mining methods included longwall, room-and-pillar with continuous miners, and drill-and-blast. The mines represented a cross-section of geology and ground support practices. At each mine evaluations were made of the Coal Mine Roof Rating (CMRR), roof support practices, pillar design methods, and general ground control experience. The coal seams observed were generally thick (2-5 m), the depths of cover moderate (less than 200 m), and the roof rocks relatively strong (CMRR greater than 45). Unfortunately, the South African roof fall fatality rate is approximately three times greater than in U.S., perhaps in part because roof bolts seem to be more widely spaced in most South African mines. Roof bolting equipment was generally outdated, and the quality of bolt installation was a major concern. Pillar design, on the other hand, is quite advanced, and pillar failures are rare. Several novel partial pillaring techniques are employed, including "checkerboard" mining in which every other pillar is removed, 3-cut systems, and high-extraction mining where engineered final stumps are left by design. The paper also offers observations on ground control management techniques (including recently introduced Codes of Practice), the role of the mine inspectorate, and the status of the research community.

Jan 1, 1999

By D. J. Maconochie

This paper describes the investigations and results of monitoring of deformations of houses located within the area of influence of a pillar collapse over the Westfalen No. 3 coal mine near Ipswich, Queensland. The subsidence resulted in minor subsidence of at least 18 modern houses and serious damage to 4 others. The history of the events and the measures taken to deal with the physical problems arising are described. The investigations and results are described and related to the mining methods and geology. The stability of coal pillars up to 9.6 m high was considered and computer modelling undertaken to relate surface subsidence to estimates of the extent of pillar failure. Assessments were made of the likely extent of subsidence during the incident. Measurements of distortion and tilt were obtained as the ground slowly subsided and criteria established to determine when the structures were deemed to be unsafe. Detailed surveys of houses affected or anticipated to become affected were also undertaken. Four houses were condemned and subsequently demolished as a result of excessive tilt. The methods of assessment are described and the implications of the results related to the various house designs.

Jan 1, 1992

By John C. Stankus

The success of cable bolts for mine ground control have been well documented in papers presented at this conference too numerous to reference. Cable bolts have proven effective over the years mainly utilized in the form of supplemental support. Some limited work has been conducted on the use of cable bolts as primary support This work has been mainly confined to the West and the bolts utilized were of a non- tensioned type MSHA requirements for primary support have been that the bolt system he tensioned or if non-tensioned, then fully encapsulated with resin. Many operators are now interested in using cable bolts as primary support Further, despite the enormous success of cable bolts, there have been questions raised about the longevity and corrosion characteristics of the cable itself particularly for long tern applications. To improve the corrosion characteristics of cable bolts, galvanized cable has been used for some applications However. although improving the corrosion resistance of cable, galvanized cable for mine ground control does not provide complete protection under certain types of situations and mine environments. Realizing a need for a cable bolt that can be used for primary support and provides consistent installed tension, complete corrosion protection, and a fast installation, Keystone Mining Services. LLC (KMS), an affiliate of Jennmar Corporation, has developed the INSTáL CableOx system. This paper will detail the development and specifics of this system including two underground case studies

Jan 1, 2000

By Peter Zhang

"Room-and-pillar mining with pillar recovery has historically been associated with more than 25% of all ground-fall fatalities in the underground coal mines of the United States. The risk of ground falls during pillar recovery increases in multiple-seam mining conditions. The hazards associated with pillar recovery in multiple-seam mining include roof cutters, roof falls, rib rolls, coal outbursts, and floor heave. When pillar recovery is planned in multiple seams, it is critical to properly design the mining sequence and panel layout to minimize potential seam interaction. This paper addresses geotechnical considerations for concurrent pillar recovery in two coal seams with 70 ft of interburden under about 1,000 ft of depth of cover.The study finds that, for interburden thickness of 70 ft, the multiple seam mining influence zone in the lower seam is directly under the barrier pillar within about 100 ft from the gob edge of the upper seam. The peak stress in the interburden transfers down at an angle of approximately 20° away from the gob, and the entries and crosscuts in the influence zone are subjected to elevated stress during development and retreat. The study also suggests that, for full pillar recovery in close distance multiple seam scenarios, it is optimal to superimpose the gobs in both seams, but it is not necessary to superimpose the pillars. If the entries and / or crosscuts in the lower seam are developed outside the gob line of the upper seam, additional roof and rib support needs to be considered to account for the elevated stress in the multiple seam influence zone. INTRODUCTION Room-and-pillar mining accounted for about 40% of underground coal production in the United States in 2016. Pillar recovery, practiced in about one-third of the room-and-pillar mines, represents about 10% of the coal mined underground, yet it has historically been associated with more than 25% of all ground fall fatalities (Mark, Chase, and Pappas, 2003). In some U.S. coal fields, particularly central Appalachia, many coal mines are operating under geological conditions with multiple coal seams. The risk of ground falls during pillar recovery increases under multiple-seam mining conditions. The hazards of pillar recovery associated with multiple-seam mining include roof cutters, roof falls, rib rolls, coal outbursts, and floor heave (Mark and Tuchman, 2007; NIOSH, 2010b). Pillar retreating creates abutment pressure, not only in the currently mined seam, but also in the overlying or underlying seams. Multiple-seam interactions become more pronounced as overburden depth increases and interburden thickness decreases. To safely recover the pillars in multiple seams, it is critical to properly plan the mining sequence and panel layout to minimize potential multiple-seam interaction."

Jan 1, 2017

By Gabriel Esterhuizen

The room-and-pillar mining method is used extensively in underground limestone mines in the Eastern and Midwestern U.S. The rock mass is typically a near-horizontal, bedded deposit at relatively shallow depth. A survey of 34 mines was conducted in which data on roof spans, rock mass properties and support practices were collected as part of a National Institute for Occupational Safety and Health research project into ground control in limestone mines. The average room width is 13.5 m (44 ft), accommodating large mechanized equipment. The results show that the immediate roof beam can consist of many individual layers and can contain several near-vertical joints. In spite of the room widths, the roof is naturally stable in many mines. Observed roof instabilities can generally be related to excessive horizontal stresses or unfavorable geological structures that cause block fallout or beam failure of the bedded roof rocks. The survey showed that the rock mass quality of the limestone does not vary significantly throughout the Eastern and Midwestern U.S. Roof conditions and the need for support were found to be closely related to the thickness and competence of the first layer of limestone in the roof. The findings highlight the need to identify local geological structures and the roof beam characteristics so that support alternatives can be evaluated. Monitoring and observational technologies that are available for identifying potentially unstable roof are presented, which include: roof characterization using the Rock Fall Risk Index, automated logging of roofbolt hole drilling, microseismic monitoring and displacement monitoring.

Jan 1, 2007

By Simon H. Prassetyo

Violent failures of coal pillars, known in practice as coal mine bumps, have long been a subject of investigation. Many field investigations have considered geological conditions that create high stress in the pillar to be the main causative factor leading to bumps. In recent years, constraint at interfaces has been observed to be associated with the occurrence of coal bursts. This paper shows how interface friction and width-to-height (W/H) ratio affect the degree of violence of coal specimen failure. A series of UCS tests on 178 coal samples from bump-prone (Utah, called UT coal) and non-bump-prone (West Virginia, called WV coal) mines were conducted. Three violent failure parameters? peak sound pressure level, core zone failure, and ultimate stress? were used to assess the violence of failure. The degree of violence were investigated at varying interface frictions (high: µ = 0.40, medium: µ = 0.22, and low: µ = 0.13) and W/H ratios (W/H = 2, 3, 4, 5, 6, 7, 8, 10, and 12). A simulation series of modeled coal specimen under uniaxial loading was also conducted using the finite element method to observe the equivalent plastic strain distribution experienced by the modeled coal specimens. It was found that the violence of coal specimen failure depends on W/H ratio and interface friction. Interface friction has more significant influence on the violence of failure at high W/H ratios than it does at low W/H ratios.

Jan 1, 2011

By Fangtian Wang

The fully mechanized longwall mining was employed in a shallow coal seam that was under the gobs of room and pillar mining and overlain by thin bedrock and thick loose sands. Operational practices have demonstrated that severe accidents would occur including roof structure instability, roof steps, damages of shield supports, and face bumps triggered by the large area roof weighting, resulting in serious threats to the safety of underground miners and equipment. This paper uses Shigetai Mine, located in the Ordos area, Inner Mongolia, as the study site. It fully considers the geological conditions of 3-1-2 coal seam and employs theoretical analysis, 3DEC numerical simulation, and field measurements to analyze the overlying strata movement for the shallow seams under an abandoned room and pillar mine without pillar extraction. The research results serve as an excellent guide to mining in similar geological and mining conditions.

Jan 1, 2014

By Christopher Mark

Despite more than half a century of experience with roof bolting, no design method has received wide acceptance. To begin to improve this situation, National Institute for Occupational Safety and Health (NIOSH) conducted a statistical study of roof bolt performance at a number of mines throughout the U.S. Case histories were collected from 37 mines with a variety of roof bolt types and patterns in a wide range of geologic environments. Performance was measured in terms of the number of roof falls that occurred per 10,000 ft of drivage. The study found that roof falls are rare when the roof is strong and the stress is low, even with light roof bolting patterns. The focus of this paper is on the more difficult conditions, where the roof is weaker and/or the stress is higher. Analysis of the results led to guidelines that can be used to make preliminary estimates of the required bolt length, capacity, and pattern. The guidelines are based on the depth of cover (which correlates with stress) and the roof quality (measured by the Coal Mine Roof Rating (CMRR), and the intersection span. Another contribution is a formula for estimating the horizontal stress level in the eastern U.S. coalfields as a function of the depth of cover. The design guidelines are currently being implemented into a computer program called Analysis of Roof Bolt Systems (ARBS).

Jan 1, 2001

By Thomas Barczak

Longwall shields provide essential ground control in Iongwall mining, yet a high percentage of shields are operating at less than peak capacity and many at well below the rated support capacity due to defective hydraulic cylinders or malfunctions in other hydraulic components. Leg pressure data are currently collected on state-of¬the-art longwall shields, but typically are not analyzed to evaluate shield performance. The National Institute for Occupational Safety and Health (NIOSH) Shield Hydraulics Inspection and Evaluation of Leg Data (SHIELD) program is a Visual Basic software system that is designed to analyze leg pressure data and identify shields that are not performing to rated specifications. The program analysis is configured to detect the following conditions: (I ) loss of leg pressure, (2) imbalance in leg pressure, (3) low set pressure, (4) low yield pressure, and (5) full extension of the bottom stage. Other performance assessment measures include the percentage of the support capacity utilized (ratio of peak load to yield load), the percent of time that a shield operates at yield load, the ratio of the set load to the yield load, and the amount of support capacity that is lost due to leaking cylinders. Historical record keeping will allow the user to select a particular shield and review the performance record as developed by the program for that shield. In addition to these performance assessment measures, the software will include an animated description of shield hydraulic systems that will describe the operation and significance of each hydraulic component and the impact of component failures on the shield's capability to provide the required roof support. A general overview of the SHIELD program is provided in the paper together with an example analysis of a 2.5-year-old Australian longwall face.

Jan 1, 2002

By Garth Kuhnhein

The Black River and Maysville underground limestone mines operated by Carmeuse Lime and Stone, Inc. in northeastem Kentucky are two of the largest underground limestone operations in the United States. The combined output of these two options has consistently averaged over 5.5- million tons per year for the last decade. The mines operated beneath 650-ft and 1,200-ft of overburden and are affected by high horizontal stress. In 1982 changes to the mine design were made at the Maysville mine to improve ground conditions. A series of design changes were initiated in 2002 at Black River to improve ground conditions. This paper reviews the results of the changes made at Maysville, recent horizontal stress measurements conducted at the Black River mine, and the recent modifications to the Black River mine design. Roof fall statistics at both operations are used to compare the distinctly different mine layouts used at the two mines.

Jan 1, 2004

By S. Q. Yang

Rotary radial jet improves greatly the pulsing velocity of airflow along each direction everywhere in the entry, intensifies transverse migration of air, eliminates effectively the local gas accumulation, and distributes methane concentration in airflow evenly and rapidly. According to the theoretical analysis of heat-transmission, mass-transmission and momentum-transmission, not only the similarity between heat-transmission and momentum-transmission, but also the similarity between mass-transmission and momentum-transmission exists in turbulent flow field, When the analogical equivalent ratio of heat transmission and mass transmission meets a certain criterion and remains a certain value, the temperature field can be used to simulate the methane concentration field. After hot airflow being released, thermograph instrument can be used to monitor the changing patterns of heat transmission and temperature distribution which simulates the changing patterns of methane transmission and methane distribution respectively. By analyzing these patterns and parameters of airflow field and methane distribution field during the process of local gas accumulation discharging by rotary radial jet, the dependability and validity of this discharging method are tested and verified.

Jan 1, 2004

By Richard R. Wilding

The United States Coal Mining Indus- try had the opportunity to greatly improve their roof control techniques during the nineteen seventies by the use of fully grouted resin roof bolts. This new tool was first approved for underground coal mines by M.S.H.A. ten years ago and during the next decade has been perfected to meet many problems previously thought to be unsolveable. The initial approved cartridge was very similar to the ones used in Europe in the nineteen sixties and since then has undergone a great deal of modification for our mines. These refinements in cartridge construction have been obtained by the close cooperation of resin manufacturers with mining personnel in perfecting pro- ducts customized to particular needs. This type of continuing program naturally necessitates a responsibility upon the resin anchor manufacturer to maintain a competant technical department. These roof control technicians by constant exposure to many of the most demanding underground problems, have developed through the years into leaders in successful applications. Today, Celtite has over twenty technically trained underground technicians with an accumulation of over one hundred years experience in resin anchors. Our documented technical reports are in excess of five thousand, involving over six hundred mines representing every major coal mining area in most mineable seams. This department has been the implement used to work with our research and development people in perfecting a continual line of improved resin anchors. This program has been a significant factor in leading the resin anchor industry into a position where approximately one third of the 1980 under- ground coal production used the fully grouted system. However, as gratifying as this accomplishment is, our experience has lead us to believe that there is an additional demand for a roof control system capable of combining the mechanical bolts ability to apply tension with resins proven superiority in anchoring. A significant number mines visited during the last decade had problems that we believed could be better answered by applying tension rather than the fully grouted approach. In most in- stances, their current mechanical installations were doing an adequate job until anchor slippage occured. Fully grouted systems solved this bleed-off problem. However, an acceptable number of falls still occured. In these some- what unique areas which we believe may amount to as much as fifteen percent of the total bolt installations, the need for improved anchors was a necessity. In developing this program we listed the ultimate requirements necessary for both the bolt and the anchor. These are for the bolt: A. Have one end manufactured so it can be grouted to the mine roof with polyester resin, obtaining a variable length from 12" to 36". B. Have a mechanism which allows the operator to tension the roof from zero to 10,000 psi. This mechanism should indicate if the roof is in compression and the bolt in tension. C. Have a mechanism which allows the operator to thoroughly mix the resin. D. The head of the bolt should not extend below the roof line any more than a normal mechanical bolt. E. Not require any extra tools for installation. F. Be bendable for use in low seam coal. G. Be durable and inexpensive. The ultimate point anchor resin should have the following characteristics: A. Have a mix and gel cycle which would compete with a mechanical bolt for speed of installation. B. Have a pull out strength in excess of a normal 5/8" mechanical bolt.

Jan 1, 1981

By Dennis Dolinar

"Tailgate entries in U.S. longwalls can be subjected to high loads and deformations. Therefore, tailgate entries are generally supported with varying types and amounts of standing support. However, even with standing support, roof falls and blockages can occur in the tailgate when the support system is not properly designed. Safe and efficient operation of a longwall face requires the selection of the appropriate type and amount of standing support. Because of the importance of maintaining a safe and functional tailgate entry, the National Institute for Occupational Safety and Health (NIOSH) is currently developing a standing support design methodology based on the ground reaction curve. Using the ground reaction curve for design requires that the ground and support interaction be quantified. This can be accomplished by the installation and analysis of data from instrumented field sites. Although necessary, the field results cannot develop the complete ground reaction curve. Numerical models, calibrated to the field results, are used to establish the complete ground reaction curve. In the present study, data was obtained and evaluated to establish points for calibration of the ground reaction curve for two western longwall operations.One test site, Mine A, was located at a depth of 1,550 ft. At this site, the floor consisted of siltstone, while the roof was an interbedded siltstone and sandstone. Because of the depth, a double row of22-in diameter CANs1 were installed to support the tailgate. Both the first and second longwall panels have mined past the instrumented site.The second site in Mine B is at a depth of only 760 ft. The floor at this mine consists of a weak shale/mudstone and the roof consists of thick, top coal overlain by weak shales. At this site, a double row of pumpable cementitious cribs was installed. The second test site has only been subjected to side abutment loading from first panel longwall mining.The measurements indicate that the support at both mines was heavily loaded when subjected to the side abutment loading from first panel mining. At the deeper site, the support began to yield when the face was more than 300 ft outby during second panel mining. In comparison to results from previous test sites in the Pittsburgh Seam and Illinois Basin, the amount of support loading and roof-to-floor convergence was an order of magnitude higher at the western sites. This has resulted in a significant difference in the position and shape of the ground reaction curves."

Jan 1, 2010

By James Pile

Long, high capacity, highly tensioned, cable bolts (strand bolts), stiff enough to be installed with resin like a solid bolt, yet flexible enough to be used in any lengths, have been widely used in Australian coal mines since the early 1990?s. A brief history and update on recent developments of this technology is provided. The first major US trial of this Australian technology, has recently taken place at BHP Billiton?s San Juan longwall coal mine in New Mexico. Thirty-five foot long, high capacity, highly tensioned, post-grouted cable bolts are being used to provide active secondary support of intersections in areas where operator safety and life of mine considerations are paramount, and standing support cannot be installed for reasons of equipment access. The cable bolts are resin anchored into overlying sandstone channels, tensioned, and post-grouted. The installation procedure and support results for these highly tensioned cable bolts are given.

Jan 1, 2007

By Binchuan Zhang

Based on the theory of fracture mechanics and blasting, computer simulations were performed to predict the original rock mass structure and those rock mass structures damaged at different levels uing the properties of joints and fratures obtained in the field.

Jan 1, 2001

By Stephen Tadolini

Standing crib supports have been applied in underground mining programs to resist large roof movements and sustain high¬loads. The strength and deformation capability of these systems has been documented under both laboratory and field conditions. The parameter that has not been examined and is not well understood is the effect that a crib or other types of standing support has on the primary and secondary bolting systems. A crib support system with low system stiffness may allow large amounts of closure and deformation and cause the bolting systems to yield or even fail. Conversely, cribs or standing support that are too stiff may experience brittle or buckling failures, negating the advantage of the intrinsic supports previously installed. Utilizing a combination of field measurements and 3-dimensional finite element modeling techniques, the relationship between system stiffness and the subsequent performance of the installed bolting system is evaluated. Additionally, a simple method for calculating the combined system stiffness for standing supports, when using materials with different strengths such as steel, concrete, wood, etc., is presented.

Jan 1, 2003

By Saeed Zhandi, Behdeen Oraee

"Rock bursts remain an important problem in longwall coal mining. These bursts are due to a sudden and severe failure of rocks from a high stress concentration in deep underground excavations that occur with the instantaneous release of strain energy stored in the rocks. They can potentially cause irrecoverable damage to equipment and personnel, thus accurate rock burst prediction and control is expected to be carried out by the mine design engineer. As a result, this can constitute major challenges for said engineer. In this paper, forensic engineering has been used to evaluate the possibility and extent of rock bursts in deep coal mining. For this purpose, established mining engineering principles, including factors influencing the severity of rock bursts, have been incorporated in the forensic engineering technique. The analyses took place in five steps:• Assessment of regional and local conditions prior to the event• Assessment of conditions after the event• Hypothesize plausible ways in which pre-event conditions can become post-event ones• Search for evidence that either denies or supports various hypotheses• Apply engineering knowledge to relate the various facts and evidence into a cohesive scenario of how the event may have occurred.The paper concludes by demonstrating a method for predicting rock bursts and preventing their reoccurrence. The methodology used in this paper, together with the results obtained, can serve as useful tools for the coal mine design engineer in the primary evaluation of rock burst potential in underground coal mines.INTRODUCTIONA rock burst is defined as the sudden and great failure of rocks due to a high stress concentration in deep underground mines. This phenomenon occurs with the instantaneous release of strain energy that is stored in the rocks, and can cause irrecoverable damages to both equipment and personnel (see Figure 1). Rock bursts pose a hazard owing to their lake of predictability; in fact, research into understanding rock burst mechanics and implementing techniques for their monitoring and prediction has been taking place for over 50 years."

Jan 1, 2015