Search Documents

By Xicai Gao

With the intensification and expansion of deep coal mining, the surrounding rock stress environment becomes further deteriorated because of the complicated geological environment and powerful mining effect, so the major deformation of roadway appeared frequently. The proportions of floor heave are increasing and , the most serious problem is the floor heave of preparatory workings. The coal seam of Binchang coal area in Shaanxi province is at a depth of 621.6 ~ 817.0 m, the average thickness of the coal seam is 25 m, and the overburden and coal measure strata are the main regional aquifers and are highly permeable. The properties of water-weakening are obvious in the floor strata. The main preparatory workings or chambers were driven in the coal seam. The severe floor heave of the water chamber appeared during early mining and the amount was 180 ~ 910mm, and seriously affected the normal installation and use of the water chamber. Theoretical study and numerical simulation as well as the in-situ measurements were carried out to investigate the deformation and failure characteristic of the surrounding rock with non-support in the floor and the main reasons which caused the floor heave were determined. A new combined support technology was proposed which consists of overcutting, grouting, backfilling and invertedarch and bolt-grouting. The field monitoring showed that the cumulative convergence of the water chamber was 20mm, the maximum convergence speed is 1.2 ~ 2mm/d, the accumulative convergence of two ribs was 36mm and the maximum convergence speed is 2mm/d. The combined support technology will enhance the support intensity between the roof and floor, the two sides of the entry and improve the loading capacity of the floor effectively and the floor heave can be controlled effectively.

Jan 1, 2013

By Anthony T. Iannacchione

The Solar No. 7 and Solar No. 10 mines were designed to prevent mine waters from directly discharging to the surface. In January of 2004, a discharge occurred as the Solar No. 7 mine was in its final stage of flooding through a barrier averaging 456-ft in width over a 1,600-ft length (No. 1). Another barrier (No. 2) was designed to protect four municipal water wells operating 1,800- ft away and producing from within or slightly below the Upper Kittanning coalbed from the adjacent Solar No. 7 and No. 10 mine pools. These two barriers were selected for this study because of varied mine layouts, mining methods, and geology factors affecting their performance. Analysis was aided by the collection and georeferencing of 6-month mining maps from the Pennsylvania Department of Environmental Protection (PA DEP). A structure contour map of the Upper Kittanning coalbed was constructed from mine map elevation points. These data and 2-ft surface contour maps were used to measure the precise location of the coal outcrop. The actual discharge point was as little as 425-ft away from a thinpillar section and 475-ft away from a pillar recovery section. The discharge point was found to be located slightly above the coal, indicating that the drainage path was at least partially through the strata directly above the Upper Kittanning coalbed. Hydraulic conductivities and potential discharge pathways are analyzed and discussed. The possible factors influencing the performance of the down-dip barriers at Solar No. 7 and Solar No. 10 are: a) the width of the barrier, b) the applied hydraulic gradient, c) the type of mining adjacent to the barrier, d) the overburden, e) the pattern and characteristics of fractures, and f) the quality of waters contained within the mine pools. This study, part of a larger effort funded by the Appalachian Research Initiative for Environmental Sciences (ARIES), is tasked to determine the key factors responsible for the successful design of down-dip coal barriers.

Jan 1, 2013

By Dakota D. Faulkner

Cable bolts anchored with traditional two component polyester resin cartridges have successfully supported difficult roof conditions in underground mines. Resin cartridges provide a costeffective cable bolt anchoring system with consistent anchorage performance characteristics when properly installed. The most commonly used cable bolts in the U.S. mining industry are 270 ksi (1,862 MPa), 0.7 and 0.6 inch (18 and 15 mm), seven-strand smooth cable with resin mixing bulbs (also known as bird cages), and 40- and 30-ton nominal capacity, respectively. However, there are other types of cable bolt anchoring systems aside from bird cages. Recently, many questions have been raised regarding the anchorage characteristics of various types of cable bolts. Keystone Mining Services, LLC (KMS), the affiliated engineering company of Jennmar Corporation, conducted a variety of controlled tests developed to closely model actual underground installations. These tests compared the performance of three commonly used cable bolt varieties, including plain, bird caged and indented seven-strand cable. Details of the laboratory testing and comparative analysis of the results are provided.

Jan 1, 2013

By Rob Thomas

Adequate load transfer is considered essential for optimum ground support and is increasingly important in weak roof and/or high stress environments. If adequate load transfer is achieved not only can this have a positive impact on the resulting roof behavior, but it may also allow the use of lower and hence more economic densities of roof support. A wide variety of post-groutable cable bolts are currently in use in the Australian coal mining industry, each of varying capacity, design, and grouting methodology. Though all of the cables are supplied with the appropriate steel specification, strength, and modulus data, the Australian coal mining industry does not have access to a comprehensive and comparative database on the corresponding load transfer performance, which is a critical problem. On the basis of the above, this paper describes the methodology and results of a laboratory pull testing program that aims to assess the impact of cable bolt design on load transfer, and specifically, the impact on the capacity and stiffness of the anchorage. As part of the testing program, 19 cables were tested including (1) plain-strand cables installed in holes drilled with 28 to 55 mm diameter drill bits and (2) bulbed and nutcaged cables installed in holes drilled with 42 to 64 mm diameter drill bits. Other parameters assessed included the significance of smooth and profiled wire, wire packing, and expanded geometry bulbs. The main results of the testing indicate that in comparison to plain-strand cables, if the cable is bulbed or nutcaged, the capacity of the anchor can increase by up to 400%, and the peak stiffness by between one and two orders of magnitude. The results also indicate that increasing hole diameter may have a positive impact on load transfer in the case of bulbed or nutcaged cables and a negative impact on plain-strand cables. No conclusive results were obtained with regard to the impact of grout strength on load transfer.

Jan 1, 2012

By Andre Zingano

The variation in pillar behavior at underground coal mines working in the Bonito coal seam is observed in both research and mining company case studies. There is no consistency in pillar behavior, as it varies from mine to mine. In some cases, it is possible to find rib yields for both excavation modes and pillar sizes. This paper?s objective is to investigate pillar behavior for different load conditions and pillar sizes. Three-dimensional numerical simulation models considering these factors were built. A matrix was then assembled to compare pillar behavior between loading conditions, as well as between different pillar sizes with the same loading condition. The results showed some pillar rib plasticity due to vertical loading and stress relief independent of the pillar size and load. For the same load conditions, the yielding thickness is the same for different pillar sizes.

Jan 1, 2012

By John Ellenberger

The nature of a stone deposit is rarely defined through exploration and engineering design, but more through the actual experience encountered as the mine develops; hence, issues with ground control are often at the forefront for a new mine. Ground control problems account for over 15 percent of lost-time injuries in underground stone mines. The objective of this work is to present actions taken during early development of a stone mine to mitigate the obvious effects of high horizontal stress on ground control. The mine was developed from a box cut with relatively little cover, and high horizontal stresses were not anticipated. Early recognition of possible high horizontal stress resulted in mapping of the mine using the NIOSH-developed Roof Fall Risk Index (RFRI) to provide a baseline to objectively analyze roof conditions. A program of borescoping the mine roof provided valuable roof beam thickness data and found that the roof beam was of minimal thickness, approximately 10 percent of drift width. As the mine developed, it became apparent that ground control problems related to high horizontal stress existed. A concentrated effort was made to improve ground conditions by implemeting a number of mitigation techniques. Actions taken by the mine included systematic roof support, reorientation of mining direction, a lower roof horizon, reduced span widths and reduced mining height in crosscuts to prevent running falls. These strategies resulted in signifcantly improved ground stability.

Jan 1, 2012

By Gabriel S. Esterhuizen

This paper addresses the need for a method to compare the effectiveness of different support systems when designing ground support in coal mines. At present, support design methods include empirical methods based on observations of past performance of installed support systems, analytical methods where the roof is typically simulated by elastic beams and numerical model analysis. The approach presented in this paper estimates the relative stability of a support design through geotechnical evaluation of the rock mass and numerical model analysis of the interaction between the rock mass and the support system. Models are used first to simulate the design performance at the expected rock conditions. The rock strength is then reduced until collapse is indicated in the model. The stability factor is then calculated as the ratio of the expected rock mass strength to the rock mass strength at the onset of collapse, and is similar to the well-known factor of safety used in engineering practice. The stability factor can be used to assist in developing a final support design by comparing the effectiveness of various support systems and the stability of excavations under various geological and loading conditions. Examples of the method?s application in three different geological settings are presented.

Jan 1, 2012

By Keith A. Heasley

The LaModel program has been used successfully in the United States for many years to design pillars to ensure global stability of pillar recovery operations. However, the recent Crandall Canyon Mine collapse showed that further research was required to improve the design of pillar recovery under deep cover. Toward this end, a new calibration procedure was implemented in LaModel. This calibration procedure prescribes techniques for calibrating the critical LaModel input parameters based on empirical abutment loading and pillar strength, as utilized in the time-tested ALPS and ARMPS programs. The calibration procedure is intended to help guide a novice modeler in choosing calibrated input parameters that produce a standard model that fits within the verification database. However, the rigid parameter specification incorporated in the calibration procedure also removes most of the flexibility in LaModel for specific calibration to the unique conditions at a given mine site. In this paper, a number of the LaModel input parameters are varied outside the bounds of the suggested calibration and the effects on the model results are analyzed. Ultimately, it is shown how the LaModel user might vary certain input parameters to adjust the model to site-specific conditions, while still maintaining the general accuracy and philosophy of the recommended calibration.

Jan 1, 2012

By Wenbing Xie

At Renlou Coal Mine, Huaibei Mine Area, the track entry deformed significantly after longwall mining in an overlying multiple seams. The supporting characteristics of primary roof bolts and shotcrete with wire mesh are closely related to the movement of the mine?s surrounding strata. A case study of a track entry deformation was monitored during the longwall mining of a selected overlying panel. The measured data showed the unique entry deformation pattern during the longwall mining in the overlying seam. Underground extensometer measurement showed that entry stability was mainly affected by the periodic roof weighting of longwall mining in the overlying seam. The displacement of the deeper strata occurred a head of the immediate vicinity of the entry. Thereafter, deformation of the roof and floor strata was in the form of shearing of the shallower strata. Due to the use of heavy-duty roof bolting with wire-mesh, the roof-tofloor and rib-to-rib convergences were small, but the floor heave was large, greater than 80% of the roof-to-floor convergence. The measured displacement from extensometers varied with the position of the monitored cross-sections and depth into the roof. There were several deformation patterns, such as shearing movement, compression, and expansion, and the variations between compression and expansion. Strata compression at the entry surface was always accompanied with shearing movement at the deeper strata. During the longwall mining, the whole surrounding strata of the entry moved toward the opening. Underground practical experience indicated that prior to mining, the entry was supported very well in excellent conditions. After mining, however, it deformed greatly. The current entry support technology was not effectively control the severe deformation incurred in entries driven in soft strata due to the following reasons: (1) little is known about the entry deformation behavior of the strata surrounding the opening and (2) the degree of interactions between entry deformation and roof bolting with wire mesh is not well understood. Consequently, effective supporting systems cannot be properly selected to control its deformation and maintain a stable supported surrounding structure.

Jan 1, 2012

By Tristan H. Jones

Beginning in 1987, miniature dataloggers approved by the Mine Safety and Health Administration (MSHA) were publicly available for sale. The principal among these was the model CR21XQM, manufactured by Campbell Scientific, Inc. These dataloggers had been tested and were deemed permissible by MSHA and thus could be installed in the return air of an underground coal mine. In 1996, production of all permissible Campbell Scientific dataloggers ceased due to lack of sales. Data collection with these dataloggers has been a staple of ground control research in the United States for decades, and, without them, or a replacement, the capability to monitor ground behavior is severely impacted. Since that time, any party requiring a permissible datalogger has needed to borrow one that was purchased during the production years. In order to fill this technology gap and ensure its own data-gathering capabilities, the National Institute for Occupational Safety and Health (NIOSH) has developed and refined its own miniature data acquisition system (MIDAS). On February 16, 2010, MSHA deemed the MIDAS to be permissible and approved it for use in the return air of an underground coal mine. The MIDAS is an intrinsically safe, 16- or 24-bit datalogger, compatible with a wide range of resistive, single-ended, and differential-type instrumentation. It contains enough data storage memory to operate for over a year with typical data rates and is efficient enough to do this on a single C-sized alkaline battery for that entire period. It is menu-driven and requires no programming knowledge to operate. It supports wireless or hardwired communication for datalogger setup and data download. This paper describes the design, field and laboratory testing, and capabilities of the MIDAS datalogger. While not as fully -functioned as the CR21XQM, it is the only new permissible datalogger available, and there is intent to make it available to the mining industry for purchase.

Jan 1, 2012

By Ry Stone

To maintain longwall continuity, NRE Wongawilli Colliery extracted the approximately 20-year-old Thompson Mains and in doing so, 20 roadways were holed into during longwall retreat. The orientation of these roadways with regard to the longwall face varied between (i) a parallel alignment where the entire roadway was simultaneously subjected to a significant increase in vertical stress on holing and (ii) a more favorable high angle of alignment, meaning that only a portion of the roadway was subjected to an increase in vertical stress on holing. In addition, the longwall holed into and was recovered in one of the existing roadways. The geotechnical environment presented several additional challenges during longwall retreat. The orientation of the stress field resulted in a major horizontal stress notch on the maingate and an elevation in the major horizontal stress in front of the longwall face during the retreat up to an adjacent goaf edge. The presence of geological structure zones also resulted in both swings in the major horizontal stress direction and increased levels of roof deformation. The gate road support designs were based on commonly accepted strata management techniques and principles. The support designs in the hole-through roadways were based on empirical design models generated from (i) aconceptual geomechanical model of pre-driven hole-throughand recovery roads and (ii) a worldwide database on pre-driven hole-throughand recovery roads. Imperative to the success of extracting the panel was a sitespecific strata management process. In this regard, consideration was given to the following: roof displacement monitoring in the gate roads (in particular, Longwall (LW) Acceleration Position), roof-to-floor convergence monitoring in the hole-through roadways, the ability of the mine to limit downtime prior to and during holing by utilizing an Authority to Mine (ATM) type process, and the use of Trigger Action Response Plans (TARP).

Jan 1, 2012

By Tom Meikle

Long tendon support systems provide several challenges when used in-cycle as part of the secondary or primary support cycle. A two-component pumpable resin, Carbothix, has been in development for use with self-drilling rock bolts, but many of the attributes of this new resin system make it ideal for grouting long tendon support systems. While neat Portland cement grouts or polyester resin capsules have been used with long tendon support systems for many years, two-component pumpable resin systems overcome many of the shortcomings in these systems. The two-component systems dramatically improve the set-time to enable mining face advance with fewer delays, enable longer pumping distances, improve quality control, and enhance load transfer mechanisms. This paper describes the key benefits associated with a new pumpable resin and details the Australian Department of Mines and Petroleum department atmospheric testing results and cable load testing completed by Minova personnel to date. It also details the results of the Australian mine site trials and the introduction of these systems into production use.

Jan 1, 2012

By Anastasia M. Suchowerska

The design of effective ground support requires a sound understanding of the pre-mining state of stress in the stratum to be mined. Irregularities in the stress field encountered during multiseam mining are governed primarily by the previous mining in the surrounding strata. The aim of this study is to quantify the effects of rock mass transverse isotropy on the vertical stress redistribution in the rock strata beneath supercritical longwall panels. Wilson?s equations for determining the stress distribution induced in and beyond a single longwall panel after it has been mined have been adopted, and a plane strain finite element analysis of an elastic medium, together with the stress changes predicted by Wilson, was used to calculate the final pre-mining stresses in the underlying strata. Values of the independent shear modulus (G¢) of the rock strata, ranging from 0.1 to 1 times the isotropic shear modulus (Giso) in the plane of the strata, and a Poisson?s ratio (?) of 0.25 have been investigated. The key finding of this study is that the predicted magnitude of vertical stress in the transversely isotropic strata beneath a mined supercritical longwall panel is larger and changes more quickly with horizontal distance than is the case for an isotropic rock mass. This finding is of significance for the design of ground support measures in multi-seam mining operations.

Jan 1, 2012

By Anil K. Ray

This paper discusses in situ studies conducted at an Illinois Basin room-and-pillar coal mine to evaluate the performances of three different types of bolts under similar geologic conditions. The bolt types considered were the fully grouted passive rebar (FGPR), the resin-assisted mechanical anchor (RMAB), and the fully grouted tension rebar (FGTR). During the evaluations, the three types of bolts were installed in a single entry covering a span of three contiguous pillars with almost identical geologic conditions. The performances of the three types of bolts were investigated by instrumentting the bolts prior to installation as primary supports on cycle. Additional data on roof behavior was collected with extensometers and shear meters placed near the instrumented bolts. Excluding some time lapse right after installation, the performance evaluation of the three bolt systems was based on the data collected for over a year. Based on this study, it was found that the axial loads measured in the different bolt types did not show any identifiable patterns under the prevailing geological conditions at the mine. Therefore, the assumption that active bolts must be superior to passive ones is not always valid. Even though the studied mine did not have any thinly laminated, weak rocks in the immediate roof, the passive bolts performed as well as the active systems.

Jan 1, 2012

By Youzhen Zhang

The drilling boom is the key component of a roof bolter, and it has significant impact on the performance, safety, and reliability of the overall working device. In this paper, the experimental modal parameters of a drilling boom at low frequencies are identified with the Laplace wavelet correlation filtering method. Based on the obtained experimental parameters, a finite element model of the drilling boom is revised using an optimization algorithm to improve its accuracy. The dynamics of the drilling boom are analyzed through its modal and harmonic response. As a result, an improvement for the drilling boom is proposed to fix the weak links and enhance the dynamic performance.

Jan 1, 2012

By Daniel W. Su

This paper presents the results of a detailed geotechnical study on the potential multiple seam interaction between the No. 2 Gas (upper) and the Powellton seams, which are separated by an average interburden of 45 ft. The interburden consists of 4 ft of clay shale below the No. 2 Gas seam, 38 ft of massive sandstone, and 3 ft of shale above the Powellton seam. The No. 2 Gas seam was mined about 60 years ago, and many water-pooled areas were projected to be present. The deepest overburden over the No. 2 Gas seam is about 750 ft. To evaluate the potential interaction between the two mine works and to determine the pillar safety factor, Analysis of Multiple Seam Stability (AMSS) software was initially used to determine pillar dimensions to obtain a minimum safety factor of 2.0 for areas under pooled water, as well as a minimum safety factor of 1.5 for areas not under pooled water. Furthermore, to assess the quality of the interburden rock strata, two surface core holes were drilled, and rock cores were tested in the laboratory for their strength and elastic moduli. Using the experimentally determined strengths and moduli as part of the input parameters, the RocScience Phase2 finite element program was employed to model the stress field scenarios and estimate the safety factors of the interburden rock strata before and after Powellton seam mining. The pillar safety factors derived from the Phase2 analysis were in excellent agreement with those obtained from the AMSS analysis. Phase2 results also predicted that the effect of the Powellton seam mining, first mining only, would reach a maximum of 19 ft above the Powellton seam, which led to the proposal of drilling 25-ft deep test holes to detect water, instead of the 45-ft deep test holes mandated by MSHA. The proposed test-hole height was accepted by both Mine Safety and Health Administration (MSHA) District 4 and the state of West Virginia. Mining of the Powellton coal seam commenced in February 2011 and continued for eight months. To date, no 25-ft deep hole has encountered water under the water-pooled zone, which validates the RocScience Phase2 finite element analysis. Also, inmine observation of excellent pillar stability and roof condition confirms the validity of the AMSS analysis.

Jan 1, 2012

By Greg Smith

This paper documents the use of bench testing equipment developed to enhance the understanding of, and improve upon, common roof bolt support systems. Most roof bolt systems consist of components that are covered within the scope of ASTM (American Society for Testing and Materials) standards. However, ASTM does not specify testing methods or performance standards for complete roof bolt ?systems?. It only designates testing methods and minimum performance standards for roof bolt ?components?. Improved understanding and continuous improvement of these systems is essential given the enormous impact that they have on the safety and profitability of underground mining operations. Bench testing equipment has been developed that effectively measures and records multiple points of deformation in a rock bolt support system while load is being applied. With this testing capability, an improved understanding of component and system stress distribution can be obtained and devices and methods for visual load indication can be developed. This paper is formatted as case studies where testing was performed to demonstrate load versus deformation profiles and to develop system improvement products.

Jan 1, 2012

By Ihsan Berk Tulu

In the Analysis of Retreat Mining Pillar Stability (ARMPS) program, the magnitude of the abutment loading adjacent to a gob area is calculated using an ?abutment angle? concept. The extent of the abutment loading is determined solely as a function of depth from an empirically derived equation. In the recommended calibration method for LaModel, it was believed that the empirical equations for calculating the magnitude and extent of the abutment load, as used in ARMPS, were the best available methods for determining these critical overburden loading values. Therefore, similar calculations were implemented in the LaModel calibration method. However, the latest in situ stress measurements of abutment loading performed in the United States and Australia have shown that there can be significant deviations in the measured abutment magnitude and extent as compared to the predicted values from the empirical formulas used in ARMPS and LaModel. It seems reasonable that the overburden geology, depth, extraction panel width, and mining height should have a significant effect on the extent and magnitude of the abutment load. However, the current empirical formulas do not incorporate many of these significant parameters into determining the abutment load on the pillars. In this paper, stress measurements from US and Australian mines were back-analyzed by using analytical and numerical methods to investigate the measured abutment extent and loading. Ultimately, it was determined that the original empirical abutment extent formula in conjunction with the original ALPS square-decay stress distribution function was supported by the case histories in this paper. Also, for depths less than 900 ft, the average 21° abutment angle was supported by the case histories; however, at depths greater than 900 ft, the abutment angle was found to be significantly less than 21° and should be calculated with a new proposed equation.

Jan 1, 2012

By Meagan S. Boltz

From October 2000 to April 2001 a local array of fourteen seismograph stations was deployed at the Trail Mountain Mine (TMM), an underground coal mine in Emery County, Utah, to locate mining-induced seismicity (MIS). Original analysis of the data provided epicentral locations that coincided closely with the active longwall panel. The original analysis yielded poor quality hypocenters, however, preventing a useful relation from being made between mining activity and the event depths. For the original analysis, only stations at elevations above mine level were used for locating MIS. As a result, P- and S-arrival times from four of the stations in the local array were not used: an inmine station and three stations at elevations below mine level. This study compares mine workings and active mining to a revised TMM dataset that included P- and S-arrival times from the lower elevation stations that were not used in the previous study. In the revised locations, a modified master event methodology was used to calculate station delays. These station delays correct for errors in the shallow layers of the velocity model. The resulting hypocentral locations have improved depth resolution, determined by a lower root mean square (RMS) for the locations, compared to the original study. Most of the events occur in the roof of the mine and follow the longwall panel. When located using the velocity model determined in the original study, the elevations of the events increase as the longwall panel progresses. One possible explanation for the elevation increase is that it may be related to geology or the caving process. As presented here, a 10% decrease in the shallow velocity structure results in a more plausible location for the hypocenters. Consequently, it is hypothesized that progressive development of the TMM longwall panel(s) may have resulted in a progressive change in the velocity model.

Jan 1, 2012

By Sanjay Kumar Singh

The mechanics of load transfer in bord-and-pillar mining is not well understood despite the evolution of the art of pillar extraction over the last 20 years via trial and error (empirical) or Rock Mass Rating (RMR), simple monitoring and pillar extraction experiences at neighboring mines. Variations in geologic conditions and pillar extraction methods, along with a lack of comprehensive instrumentation programs for monitoring ground behavior during pillar recovery, are among the factors that make it difficult to predict how strata will respond to pillar extraction. Efficient and safe use of roof supports depends on the interaction between the designed support and coal strata. Of particular interest in this study is the mechanics of strata deformation as influenced by geologic conditions, pillar extraction methods and optimum support with load-bearing capabilities in strata control during mass exploitation of underground coal deposits required detailed investigation,?. To provide a better understanding of the mechanics of strata deformation, as researchers, we have collected data and reviewed measurements of convergence and stress in one mine of South Eastern Coalfields Limited (S.E.C.L.), i. e., in North Chirimiri Pondary Hills (NCPH) and have completed numerical modeling with FLAC software for (Fast Lagrangian Analysis of Continua modeling, Itasca India Consulting Pvt. Ltd.) for two typical pillar extraction plans. Stress distribution in the mine roof above pairs of roof supports was calculated to demonstrate how Resin roof bolt support installed support contributed to roof block movement control. It was shown that overall stress and roof-floor convergence patterns were most influenced by the stiffness of coal measure rocks and by pillar extraction sequences and layouts. Also, resin roof bolts and other support systems play a critical role in controlling stability of both the immediate roof and the main roof for a distance of up to 18 meters (i.e., working coal seam height X three times) above the seam. Installed supports provide unique strata control advantages over other types of secondary support by significantly reducing the time between mining and installation of the secondary support. Although resin roof bolts are similar to posts in stiffness and capacity, they are more effective than posts under static loads because they can yield and still maintain loads at nearpeak capacity(Singh, et al., 2006), whereas posts fail and lose their ability to limit mine roof deformation.

Jan 1, 2012