Search Documents

By C. A. Rowland

Introduction Ball mills are lined drums, either cylindrical in shape or modified cylinders that have either one or both ends of the shell, consisting of conical sections, that rotate about the horizontal axis. Fig. I I shows a cylindrical mill, Fig. 12 a conical ball mill, and Fig. 13 a Tricone ball mill (Hardinge tradename). Steel or iron grinding media, generally in the shape of spheres, are used to grind the ore to the specified product size. In order to obtain more contact area for grinding and to simulate the shape of worn balls, balls have been made with two concave surfaces diametrically opposite each other. Some concentra¬tors, such as Erie Mining Co., have used slugs cut from worn and broken rods to supplement the balls in ball mills and save money otherwise lost as rod scrap. Cylindrical and conical shapes have been tried instead of balls, but balls remain as the most common shape grinding media used in ball mills. Ball mills were a logical development from the earlier pebble mills that used hard natural pebbles such as flint pebbles or sized ore pebbles (obtained from the ore itself) as grinding media. In the early 1900s36 it was found that when cast iron or cast steel balls were used in place of flint or ore pebbles, the mills drew more power and gave greater production capacity. Advances in technology have resulted in the manufacture of ball mills up to 18 ft diam inside shell, drawing up to 8,000 hp. Ball mills are employed to grind ores, especially the more abrasive ores, to finer sizes than can be produced economically in other size¬reduction machines such as roll crushers, hammer mills, and impactors. Ores can be ground dry-dry grinding-or in a slurry-wet grinding-using ball mills. Dry grinding nominally refers to less than I %v moisture by weight. If the moisture content increases by several percent, dry grinding capacity is significantly reduced as shown in Table 17. The usual range of solids content in wet ball-mill slurries is from 65 to 80% by weight. Wet grinding is used to prepare the feed material for unit opera¬tions such as flotation, magnetic separation, gravity concentration, and leaching that require a slurry of liberated valuable mineral and unwanted gangue particles. Dry grinding" is employed to produce feed for agglomeration, pelletizing, and pyrometallurgy processes that require feed that is dry or nearly so and for finely ground industrial mineral products used in the dry state. Dry grinding is also used when minerals cannot be dewatered economically to the required moisture level or when the ground product reacts unfavorably with liquids. For example, cement clinker must be ground dry. Dry grinding requires about 30% more power than wet grinding for comparable size reduction .28 The total power required in a dry¬grinding ball-mill plant including drying may be double that required for a wet-grinding plant. Grinding-media and liner consumption in dry grinding reported as pounds of metal consumed per kilowatt-hour per ton of ore" is 10-20% of that used in wet grinding. The Wabush pellet plant, Point Noire, Que.3o reported ball consumption dropped from 6.3 lb per ton of ore ground to 2.5 lb per ton of ore ground when they converted from wet to dry grinding, and a 30% increase in power consumption. A number of comparisons made on wet and dry grinding of cement raw materials show metal consumption in dry grinding to be 10% of that in wet grinding. The capital costs for wet grinding are generally lower than for dry grinding. When thickening and filtering of the wet-ground product are required, dry grinding may have a lower capital cost. With open-circuit grinding the ball-mill discharge passes directly to the next processing step without being screened or classified and no fraction is returned to the ball mill (Fig. 14). In closed-circuit grinding the ground material, undersize, in the ball-mill discharge is removed either using a screen or a classifier with the oversize being returned to the mill for additional size reduction (Fig. 15). The over¬size material that is returned to the ball mill is called the circulating load. Open-circuit ball-mill grinding requires more power than closed¬-circuit grinding for products containing similar amounts of top-size material. The less the amount of oversize allowed in the product, the longer the ore must remain in the ball mill when grinding in open circuit. This increases the production of extreme fines and thus the consumption of more power. The power required for open-circuit ball-mill grinding can be estimated using the multipliers listed in Table 18 and knowing the power required for closed-circuit grinding to yield the desired product particle size. For example, assuming the desired grind size is 90% passing some specific top size, open-¬circuit grinding would require 1.40 times the power to achieve similar results as closed-circuit grinding.

Jan 1, 1985

INTRODUCTION Automatic controls are devices that assist operators by performing routine tasks faster and better than they could alone. Great strides have keen taken in the development of new processes and bigger machines to improve productivity, but these developments created the need for increased protection of machinery and labor. The new production-line techniques, or continuous processes developed, resulted in routine and, frequently, demoralizing jobs. The human race is not constituted mentally to perform routine operations. Devices were needed also to gather information automatically and perform routine functions. High-capacity plants incorporating large equipment

Jan 1, 1985

By Norman L. Weiss

The full importance of tailings disposal is yet to be realized by the mining industry, but our awareness of its present and future implications is growing faster, perhaps, than any single phase of ore processing. Few engineers can look very far into the future because of the complexity of the problems that may confront us if we project from the general indifference of past years through what we are already being expected to correct in existing operations, to confrontations with new statutes and an awakened public in any new plants hence- forth. The mistakes of the past have not been limited to the United States nor even to other countries of the Western Hemisphere. Indeed, all continents and subcontinents have suffered from myopia in releasing the tailings without retaining responsibility. However, the US as one of the world's great leaders in technology has a particularly unimpressive record. It may be safely generalized that the degree of control applied to the tailings of a milling operation has depended upon several factors more important than national boundaries. Thus in arid and semiarid climates no incentive was needed other than the scarcity of water to create a permanent and stable lodgment for mill tailings. On the other hand. where water has been plentiful. the temptation to let the tailings run into a river or lake or ocean (at least at certain times of the year) was often irresistible. So we find that modem tailings disposal in the southwest deserts of this country, with one or two notable exceptions where very serious breaks seem to occur at regular intervals, is satisfactory according to the standards of the 195QF and 1960s. while in various operations in Idaho, Michigan, western Colorado. Newfoundland, and elsewhere the record has been less praiseworthy. In the same way, cyanide plants which did not concern themselves about leakage, seepage, spillage, or wastage of tailings pulps with solutions containing toxic levels of free or combined cyanide soon heard a demand for better control. In consequence the industry has seen a growing use of cyanide regeneration of tailings or wash solutions, elimination of leakage, and careful structuring of tailing dams. The chemical and thermal qualities of tailing waters have occasionally been a spur to good tailings management. Some tailings disposal problems for example, the southeastern Florida phosphate clays and the Bayer red muds-have been given the intensive study they merited, but not always with much success.

Jan 1, 1985

By T. R. A. Davey, J. W. Sherman, B. J. DiSanto, G. Bjorling, G. S. Stacey, J. T. Cullom, R. L. Bird, S. E. Woods, J. C. Blair, Jorma Honkasalo

Most pyrometallurgical processes take place at high temperature with rapid chemical reactions when the elements and compounds are usually liquid or gaseous. Smelting. The classical method of obtaining a metal from its ore or concentrate is to smelt it in a furnace. The initial letter "s" of this word implies that, in addition to the physical process of melting, a chemical change also occurs. This is usually the reduction of metal oxide to metal by carbon or through a series of processes involving oxidation and reduction. Since solid-solid contact would not be sufficient to give a high rate of reaction, most smelting reactions occur by medium of two reactions involving solid-gaseous contact: where M represents a metal. The commonly preferred unit for carrying out these reactions is the blast furnace,1 which is a vertical shaft of refractory brick or water-cooled steel in which lumps of metal oxide and coke are fed at the top, and an air-blast is injected through tuyeres (water-cooled pipes) in the bottom. Molten metal is withdrawn from a pool at the bottom of the furnace, while N2, CO, and CO2 gases leave the top of the furnace, carrying some fine dust or fume with them, which

Jan 1, 1985

S.L. Barua and Y.C. Kim M. Armstrong's paper is very interesting and can be regarded as a pioneering work of applying geostatistics on washed coal. The density levels used in her study are uniformly spaced, which facilitated curve fitting through a proper experimental design. Most of the existing coal washing plants in the US, however, gather washability data at non-uniform intervals which, in turn, affects the goodness of curve fitting. We would like to emphasize the importance of having a proper experimental design, if a similar geostatistical application is to be conducted on washed coal. We, at the University of Arizona, tried the variogram on recovery (Kim, Barua, and Baafi, 1982, SME preprint 82-143) which showed a similar pattern as Fig. 4 of Armstrong's paper. In both cases, the first experimental variogram value is invariably and inexplicably higher than the second variogram value. Although Armstrong ignores the first point because of "small number of sample points," we did not do so because there were 17 sample pairs. As a consequence, we concluded that the obtained experimental variogram was unsatisfactory and that further research is warranted. In other words, this disagreement in variogram interpretation between M. Armstrong and the University of Arizona begs the question whether the experimental variogram of Fig. 4 truly reflects the spatial correlation in washed coal, assuming there is such a correlation. Finally, we wish that Armstrong could have done a similar study on clean sulfur, which is a vital interest to the coal mines in the US. Her implied remark on sulfur in the concluding section of the paper may turn out to be incorrect because our experimental variograms on clean sulfur at different density levels were even less satisfactory than those on recovery.

Jan 1, 1985

By David S. Young

All pigments and extenders or fillers whether organic or inorganic fall into the following broad general classes: I. Colored II.-White III. Black IV. Metallic A pigment- is any particulate matter that is essentially insoluble and chemically unaffected by the media into which it is dispersed. According to this very broad definition, colored pigments, white pigments, fillers, extenders, and functional pigments would all be included. The particulate size range would also be quite broad ranging from very fine colloidal particles (~0.01µ) to relatively coarse particles (~100.0µ). This broad definition is usually subdivided into more practical divisions which tend to relate the classification of the pigment to its primary function in the system in which it is used. Hence, the word extender implies that its major purpose may be to extend the system.

Jan 1, 1985

By Bonn J. Macy, David A. Gulley, William A. Vogely

INTRODUCTION Some of the most famous and graphic environmental incidents have arisen from mineral extraction, including oil spills, the Reserve Mining asbestos tailings case, Kaiparowitts surface mining and coal combustion, and other environmental causes celebre. The remote location of much of the mining industry to some extent reduces the human health hazards from pollution, but often times the pristine locale in which mining is conducted provides a sharp contrast to the impacting industry. This prompts questions as to what the research literature says about the true costs and benefits of environmental compliance. We survey the state of this knowledge. Where possible, we discuss studies focused on mining and related industries, such as primary metals production. In many cases, how- ever, the studies pertain to the economy as a whole. For present purposes, the mining industry is defined as companies engaged in the production and refinement of minerals, including metals, fuels, and nonmetallics (e.g., phosphate, sand and gravel). There are several stages in mining, with environmental effects occuring at every stage. The exploration stage comprises the period from initial prospecting to the point where the deposit has been located and delineated in sufficient detail to permit development decisions to be made. Geophysical and geochemical surveys, diamond drilling programs, and exploratory stripping and excavation are activities that may be employed during this stage. Some forms of prospecting are relatively benign, al- though even airborne surveys and motor vehicles generate noise pollution. Roads and the passage of vehicles and equipment affect land surfaces and vegetation, and attract heavier backcountry use. Clearings, stream crossings, and borrow pits can lead to increased erosion and sedimentation of streams. Geological survey grids disrupt vegetation and appearance. Moreover, prospecting can involve the excavation and stripping of overburden, resulting in soil and vegetation disruption as well as in- creased sedimentation of streams and lakes. The effects of exploration are often temporary, and frequently less severe than for other activities. Nevertheless, exploration-related impacts vary with the intensity and type of exploration effort, and can be significant. During the development stage of mining, shafts are sunk, pits excavated, buildings erected, and transportation facilities established. Dust, noise, and other socioeconomic and environmental impacts are generated by the relatively large and sudden influx of people, equipment, and activity. Surface disturbance and solid waste are generated by development, and liquid wastes form when mines are dewatered. The extraction phase is associated with a variety of environmental impacts. These impacts may differ for surface and underground mines. In surface mining, surface disturbance is obviously a major consequence. Piles of overburden and waste accumulation mar land surfaces. Wind and water erosion tend to spread the dis-

Jan 1, 1985

By Charles W. Daugherty, Eugene B. Waggoner

In the construction of recent subsurface projects, particularly mined openings and transit systems, it has been apparent that final costs were often greater than first expected. Because many overruns result from alleged differing site conditions, there was reason to suspect that pre-bid geotechnical investigations were inadequate for predicting subsurface geology. In 1982, nine federal agencies involved in constructing underground facilities funded the National Academy of Sciences' U.S. National Committee on Tunneling Technology (USNC/TT) in an effort to evaluate and clarify the relationship between geological knowledge and construction costs. That committee formed the special Subcommittee on Geological Site Investigations, which spent more than two years studying underground projects by examining contract documents and geologic reports, making site visits, and interviewing owners, designers and contractors. The study ultimately encompassed 84 mined tunnels and chambers and three deep shafts in the United States and eastern Canada. Data collected on geologic exploration, design and construction were analyzed and conclusions reached concerning whether and how site investigations need to be improved. The results of the study are published in two volumes by the National Academy of Sciences. Due to the recent completion date of the main report, it was not possible to prepare a summary for inclusion in the RETC Proceedings. However, the complete two-volume report, "Geotechnical Site Investigations for Underground Projects," can be obtained by writing or calling: U.S. National Committee on Tunneling Technology National Academy of Sciences 2101 Constitution Avenue, N.W. Washington, D.C. 20418 (202) 334-3136

Jan 1, 1985

By J. H. Bassarear, J. D. Vincent

General. Copper, the first metal used by man, today is the third in consumption after iron and aluminum. Compared to these it is relatively rare, with less than 0.01% of the earth's crust copper, 8% aluminum, and 5% iron. Nevertheless. our modern civilization is heavily dependent upon copper because of its high conductivity and resistance to corrosion, ease of working, durability, wide range of properties by virtue of its readiness to form alloys with other metals, and its attractive colors and texture that make it so desirable for many crafts and arts. These attributes explain why copper is chosen for a long list of uses, including electrical wiring, switchgear, and bus bars; piping, roofing, and siding; and manufactures of brass, bronze, and other alloys. The fact that copper ore is mined in nearly all parts of the world is significant. Its importance is shown in Table I, which gives figures on world production from 1968 to 1977. In the Free World, North and South America and Africa are preeminent. The table also shows the generally upward trend of production in this period; accurate figures for 1978 and 1979 from the same source are not yet available (1980), but it is certain that major environmental, economical, and political factors continued to disturb the industry in those years and into 1980.

Jan 1, 1985

Contents

Jan 1, 1985

By Mark E. Gershon

Extensive efforts are under way to- ward applying computer techniques to mine production scheduling problems. These efforts are concentrated in four areas: optimization, computerization of traditional methods, heuristics and simulations. These areas complement each other rather than compete. Characteristics of each are discussed toward enabling the engineer to evaluate specific systems that may be encountered. Alternative approaches within each classification are described as well as the motivation for each.

Jan 1, 1985

By Z. Rogovin

In order to develop more accurate procedures for scale-up and design of semi-autogenous-grinding mills through detailed mathematical models, a better understanding of the charge motion and rock/ball segregation is needed. To achieve this a 0.61 m (2.0 ft) diameter x 0.305 m (1.0 ft) length plexiglas mill was constructed as a scale model of a commercial SAG mill. Rock motion in the rotating mill was simulated using various sizes of ceramic balls. Quantitative measurements of dynamic angle of repose, water and slurry motion, holdup and size segregation of the charge were taken. In addition, a video-presentaiton (available to the public) was prepared to elucidate charge and water motion at various mill speeds, charge volumes, rock size distribution and flow rates.

Jan 1, 1985

By N. W. Johnson

Two analysis tools which have been applied to problems in industrial Flotation processses are the application of kinetics and detailed mineralogical or liberation data, both on a size-by-size basis. The paper describes practical examples of the application of kinetics to examination of the entrainment recovery mechanism, the retardation of valuable minerals at the commencement of flotation sections and the resolution of problems related to valuable species with reduced rate constants at the end of sections. Examples of the usefulness of size-by-size liberation data for monthly composite samples of products from a concentrator are also described.

Jan 1, 1985

The concept of "classification is expanded beyond the performance of the classifying equipment to include all aspects of the fines removal system of the grinding circuit. Design and operating parameters which affect fines removal are identified and discussed, and a quantitative index for circuit fines removal effectiveness is defined. This approach lends new interpretation to certain observed phenomena, and suggests useful guidelines for circuit design and operation.

Jan 1, 1985

By M. J. Shulman

The exploration geologist is frequently confronted with the problem of allocating his resources, i.e., exploration effort, among various areas. Although geologic, financial and logistic considerations influence the allocations, no objective criterion is usually given which determines the optimal allocation. Maximizing the gain in information, subject to the constraint of a limited exploration budget, is used as the objective criterion to allocate reconnaissance effort. The information function, I(x), quantifies the expected gain in information, where x is the scale of exploration. To calculate the information function the following data are necessary: 1. The probability that an area contains a target must be estimated. 2. For each scale of exploration, four probabilities must be estimated: the probability that an anomaly is produced by the target; the probability that an anomaly is not produced by the target; the probability that an anomaly is produced by a barren area (false signal); and the probability that an anomaly is not produced by a barren area. Alternatively, the barren area can be replaced by other targets. To illustrate the allocation model, the optimal number of line kilometers/line spacing per area is determined for an aeromagnetic survey for iron in Egypt.

Jan 1, 1985

By M. J. Hrebar

Surface coal mine design has traditionally relied on graphic and analytic approaches for pit layout and equipment selection. A number of interactive graphic microcomputer programs have been written which aid in the design process in the academic arena and should also have industrial applications. The programs described include a dragline cut diagram and production index calculation program, a downslope load scraper cut diagram and volume program and an overburden volume and coal tonnage sequencing program.

Jan 1, 1985

By Maribeth Amyot

This paper assesses the current status of computing education in ABET-accredited mining engineering programs in the United States. The hardware and software being used are reviewed. The extent to which computer applications are incorporated into mining engineering courses is also surveyed. Today's capabilities and practices are compared with those of the past to establish, trends in computing education. The concerns of mining educators regarding computers are addressed, as are views on the direction in which mining engineering programs appear to be heading in preparing students to meet the computing needs of industry.

Jan 1, 1985

By R. Bhaskar

The control of respirable dust in mines has been given paramount importance due to the health and safety implications associated with fine dust. The understanding of the temporal and spatial behavior of dust has been recognized as essential for increasing the efficiencies of the existing control techniques and for developing new control strategies. Mining-related studies in this area are, in general, limited. They are also mostly experimental. Some mathematical and computer analyses have been attempted. In this paper, first a review of the mathematical studies performed in the last three decades in this area is presented. Second, a mathematical model for analyzing dust flow in mines is proposed. The model takes into account a number of factors affecting dust transport. It incorporates varying dust generation source strengths and dispersion, deposition, and coagulation of dust in mine airways. Finally, application areas for the model are discussed. A computer program based on the mathematical model has been developed. The program will output the dust concentration in the mine atmosphere as a function of time and distance from the source. The amount of dust deposited on the sides, roof, and floor of the airway is also determined.

Jan 1, 1985

By L. J. Jansen

Techniques utilized to incorporate geological data in computer modeling and ore reserve estimation have undergone considerable evolution during the past fifteen years. Computer analysis and evaluation of two precious metal deposits are presented as examples of innovative computer techniques developed at Asarco. The first is a gold deposit occurring in a steeply dipping Pre-Cambrian greenstone sequence. The second is a manto-like manganiferous silver deposit occurring in a relatively flat sequence of Late-Paleozoic sediments. In both deposits, four sub-horizontal zones of geological influence are evaluated.

Jan 1, 1985

By Larry F. Barrett

Anaconda exploration in the Rico mining, district from 1978 through early 1983 resulted in discovery and partial definition of the Silver Creek molybdenum deposit. Approximately 44 million tons of 0.31% Mo are drill-indicated, and projections suggest that the deposit exceeds 200 million tons. No source intrusion has been intersected by drilling, but its composition is suggested by silicic alkali-alaskite porphyry dikes of intramineral age observed at the surface and in drill holes. Age data and fluid inclusion studies indicate that the deposit was formed 5.2 ±2 m.y. ago and that more than 1,200 meters of cover has since been removed by erosion. Both emplacement of the hypothesized source intrusion, and the geometry of the molybdenum deposit, were influenced by three major intersecting faults. The most significant of these, the Last Chance fault, juxtaposes Precambrian quartzite and greenstone against Pennsylvanian clastic and calcareous sediments within the mineralized zone. Wallrock alteration associated with the deposit is characterized by potassic, phyllic, and propylitic zones in non-calcareous rocks, and garnet and anhydrite-diopside zones in the carbonates. All +0.2% Mo mineralization is within the potassic and garnet zones. Pre-mineral faults that intersect the deposit contain the only surficial molybdenum, tungsten, and fluorine anomalies. Pervasive dispersion haloes of the indicator elements were intersected at depth by drilling in the discovery phase of exploration, and are particularly well-developed in the hanging wall of the Last Chance fault.

Jan 1, 1985