Search Documents

By M. P. Saunders

A comprehensive, site specific water management plan is of primary importance to the successful implementation, operation and decommissioning of any mining project. Formulation of a plan requires an orderly planning process consisting of identifying problems, establishing planning criteria based on the guidelines and requirements of regulatory agencies, and an iterative procedure of identifying, investigating, and evaluating plan elements and alternative plans. A typical uranium surface mine operation consists of a mine pit or pits, spoil pile areas, crusher, processing plant, and tailings disposal area. A water control plan addresses the problems of diversion of natural runoff from undisturbed areas around the mine; and diversion, collection, and treatment of runoff from within the mine area. A water control plan is required to determine the location and size of appropriate control and detention structures; their cost; and the schedule for permit activity, design, and construction. The plan must be formulated to meet the requirements of both the State and Federal regulatory agencies.

Jan 1, 1981

By A. E. Desrosiers, R. L. Kathren, D. L. Haggard, J. M. Selby

INTRODUCTION The radiological health significance of thorium-230 stems from its tendency to separate from the uranium238 parent, concentrate in bone tissues, and to subsequently irradiate the radiosensitive tissues lining the bone surfaces and the bone marrow. Indeed, thorium-230 may be the radionuclide which contributes the major dose following intake of natural uranium (Hartley and Pasternack 1979). This is reflected by the most recent recommendations of the International Commission on Radiological Protection, which specify the limits shown in Table I for the annual intake of radionuclides by occupationally exposed workers (ICRP 1979). TABLE 1. Occupational Annual Intake Limits (microcuries per year) for Selected Uranium Nuclides and Daughters (ICRP 79) [Radionuclide Ingestion Inhalation] [Uranium-238 200 0.05 Uranium-235 200 0.05 Uranium-234 200 0.03 Thorium-234 300 200 Thorium-230 3 0.02 Radium-226 2 0.5] Clearly, the relatively low annual limit of intake for thorium-230 shows it to be of greater radiological concern than its parent radionuclides. Because of the greater toxicity and different metabolism of thorium-230, monitoring only for uranium-238 does not satisfactorily identify the possible hazard from thorium-230 nor does it provide any real indication of the metabolism or biodynamics of these two radionuclides. Thorium-230 has a half-life of 80,000 years and can be detected by direct counting of the alpha particles or photons emitted during its transformation to radium-226. The 4.69 and 4.62 MeV alpha particles are distinctive and specific indicators of thorium-230 and are emitted with abundances of 76% and 24%, respectively. The principal photon, a 68 keV gamma ray, is emitted in only 0.37% of the transformations and is, therefore, not useful for low level measurements. The other photons emitted have even lower yields, or, in the case of radium L x-rays, are non-specific and, hence, useless for quantification. High sensitivity measurements of thorium-230 currently are usually accomplished by wet washing of the sample substrate, quantitative chemical separation of thorium atoms, and, finally, direct measurement of the alpha particles emitted from a massless deposition. This procedure is complicated, expensive, and time-consuming, and subject to interferences from uranium, other actinides, and other thorium isotopes. Recently, the feasibility of low-level measurement of thorium-230 by neutron activation analysis (NAA) was demonstrated (Kathren, Desrosiers and Church 1980). Two principal variations of the NAA method were used in this study: 1) instrumental NAA technique and 2) post-irradiation radiochemical separations (RCS). Instrumental NAA procedure is a nondestrucive technique which is preferred because of its simplicity. The procedure is as follows: after irradiation with a known neutron fluence, the samples are transferred to a clean container and quantitative gamma spectroscopy performed. With the radiochemical separations procedure, the sample is initially treated as in the instrumental technique. However, after irradiation, a known amount of "carrier" is added to the sample. The element(s) of interest are then separated from the rest of the matrix by distillation, precipitation and extraction techniques. The resulting sample, now free of interferring elements, is then ready for gamma-ray analysis. The use of a "carrier" is to determine the loss of element-of-interest during the chemical separations process. The neutron activation cross section of thorium-230 has an epicadmium resonance value of 1,010 barns (Mughahghab and Garber 1976) and a thermal neutron cross section of 23 barns. The 25.52 hr thorium-231 produced releases two photons of significance: an 84 keV complex, (6.5% yield) and 25.6 keV (15% yield) (Lederer and Shirley 1978). The 84 keV complex is particularly useful for quantification since neither natural uranium, thorium, their daughters, or activation products emit photons in this region. However, the higher yield of the 25.6 keV photon may result in increased sensitivity if there are no other photons of similar energy emitted by other radionuclides in the sample. PRELIMINARY STUDIES Thorium-230 standard stock solution was prepared from a pure sample of the oxide purchased from Oak Ridge National Laboratory. From this stock solution a series of samples were prepared for irradiation in the TRIGA Mark I reactor at Reed College. Various dilutions were prepared as well as thorium-230 spiked urine samples. Irradiation times varied from 1 to 54 minutes in a neutron fluence rate of 1.84 x 1012 n/ cu m-sec. The neutron spectrum was abundant in thermal neutrons, having a Cd ratio of approximately 10. Treated urine samples were also analyzed by the NAA instrumental method. Analysis of untreated urine samples was not possible due to the high background

Jan 1, 1981

By George Hufford

An investigation is made into the applicability of queueing theory to simulating the operation of a large open pit copper mine in the southwestern United States. Actual data from a working mine was used to construct curves for truck loading time, haulage and return time, and dumping times. Known results of investigations of queueing models (Koenigsberg - 1958, Gordon and Newell - 1967, Cabera and Maher - 1973) were used to simulate the actual operation. These did not give acceptable results so commonly used probability distributions were fitted to the actual data. A large computer program known as Q-GERT was used with the various parameters obtained from fitting the curves. Kolmogorov- Smirnov tests were run that showed that this was not satisfactory either. Finally, Q-GERT was used with the actual data from the mine. An appropriate correction factor is then found to apply to the exponential probability distributions tested previously and satisfactory results are obtained.

Jan 1, 1981

By V. Roze, R. N. Parkinson, R. Shepherd

The alphaDOSIMETER is a complete, integrated system designed to monitor the immediate worksite of underground miners where the disintegration for radon daughters is a risk to the health of mining personnel. The dosimeter weighing little more than one pound is worn by each miner throughout the entire shift and is powered by the miner's cap lamp battery. After this integration period, the unit is connected to a reading network whereupon the day's data is dumped, calculated and stored. Beginning in July 1980, prototype units were subjected to vigorous underground testing in uranium mines in Canada and the United States and in tin mines in Cornwall, U.K. The testing results are summarized and proposals advanced for a typical mine monitoring system utilizing the alphaDOSIMETER.

Jan 1, 1981

By James P. Bowersox

Modem mineral processing plants handle large amounts of ore and produce large tailing streams. Plant performance can be optimized when the water is quickly recovered with a thickener. The caisson thickener was developed to overcome process and mechanical problems with the conventional traction and center column units. The caisson is a hollow center column that serves as a pump house. The rake arm structure is supported by a hydrostatic bearing which sits on top of the caisson. The caisson thickener with a hydrostatic bearing has operated for many years in several mineral processing applications.

Jan 1, 1981

By Wayne P. Myers

Electricity, as normally thought of by a layman's definition, is a man- made force that has no color, no odor, is not visible, cannot be heard, yet man can control it and make it perform his work for him. A person dare not cheat on it, for it then will master him. It has laws, rules, and regulations that must be strictly adhered to if it is to perform in the safest, most reliable, and economical manner. In the early days of coal mining the power source was man himself. Later man employed steam and compressed air to reduce his muscle power requirements needed in the extraction of coal. By the turn of the 20th century, electricity had become the most common source of power for the coal industry. Steam and compressed air are still found in use in isolated cases today for specific applications; however, they are rapidly being replaced by electricity. Electrical laws and regulations are quite extensive and somewhat complex for the proper generation and use of electricity. Man-made laws, rules, and regulations for the care and handling of electricity, designed for man's safety, are rigidly enforced by Mine Safety and Health Ad- ministration (MSHA), as well as the various state departments of mines.

Jan 1, 1981

By Frank R. (Original by) Barnako

Coal mining historically has been a hazardous occupation but, in recent years, tremendous progress has been made in reducing accidental coal mine deaths and injuries. The purpose of this chapter is to discuss the basic principles of accident prevention as they are related to coal mining. Accident prevention fundamentals are no different for coal mining than for any other type of work. The fundamentals apply to all industries. Construction workers may be struck by falling tools and materials, and miners may be struck by falling slate and coal. Sailors may be trapped by shipboard fires, and miners may be trapped by mine fires. Railroad brakemen may lose hands and fingers positioning couplers, and miners may lose hands and fingers positioning couplers. Many other examples could be cited, but the point is that accidents that happen in coal mines are basically similar to accidents that happen in other industries. Thus, the basic principles for preventing accidents apply in coal mining as they do in any other type of work.

Jan 1, 1981

By Joseph S. Malesky

The discovery and development of explosives mark one of the most important findings in the history of civilization. Without explosives our vast economic enterprise concerning the mining of coal, copper, iron, aluminum, and various other ores could not function. Explosives are used in all kinds of construction works, in the razing of old buildings, blasting of trenches, driving of tunnels, and in many other instances common to our everyday life. For these reasons explosives are rightfully referred to as the forerunner of progress. An explosive may be defined as a substance (usually a mixture) that, when flame or shock is applied, yields readily to rapid combustion or oxidation, accompanied by the formation of such relatively large quantities of gases as to produce much violence and pressure which, in turn, react against their surroundings and cause what is termed an explosion. By their very nature the action of explosives is destructive and disruptive of adjacent materials. Decomposition of explosives can occur through deflagration, which is rapid burning or combustion, as in the case of black powder, or through detonation, which is an almost instantaneous disruption, as in the case of dynamites and blasting agents.

Jan 1, 1981

By Robert L. (Original by) Llewellyn

Many of the problems that occur in the preparation plant originate from practices in the mine. Impurities in raw coal can be in the seam itself or from extraneous material taken in mining from the roof or bottom. In the case of underground mines, the choice of mining equipment will affect the size consist and the amount of extraneous material included with the coal. Also, governmental regulations concerning the degree of rock dusting, gobbing underground, and cleanup have increased the dirt in raw coal. Sulfur dioxide emission standards, on the other hand, are pressuring the coal industry to clean coal more thoroughly. Coal supplied for coking purposes is nearly all upgraded by washing, while for the largest market, electric power generation, a high proportion is shipped as a raw product with processing, in whole or in part, only necessary when excess impurities are mined with the coal. This chapter will deal primarily with plants that process or wash coal to some extent (Fig. 1) and only incidentally with mines shipping raw run-of-mine coal crushed to a top size of, usually, 51 to 102 mm (2 to 4 in.), with little, if any, other treatment.

Jan 1, 1981

By Andrew R. Thomas

As the demand for most industrial minerals on the world market continues to climb, educational institutions maintain traditional policy in emphasizing chiefly metallic ore deposits and energy resources in addition to the general disciplines. In spite of their increasing importance, few universities exhibit great depth with respect to industrial minerals courses due to the shortage of specialized faculty in a category this broad. As new ideas are formulated and technological advances are developed in the field of industrial minerals, the classroom still exists as a student's primary source of information. This opportunity to give today's students the benefit of modern developements has not been utilized to its utmost potential.

Jan 1, 1981

By Douglas J. Lacke

1974 marked the start of a new era for Climax Molybdenum Co., a division of AMAX, with the initiation of an open pit operation above the existing successful underground block panel caving mine. A number of problems posed a challenge to the Climax open pit. Highly fractured rock, old mine workings, permafrost, and more than 7.6 m/a (300") of snowfall forced changes in normal operations. Final pit wall design was altered. Production bench heights were lessened due to old workings. These and other modifications contribute to a highly successful open pit operation.

Jan 1, 1981

By Richard S. Kunter

The Bulldog CIP plant treats the slime portion of current tailings and reclaimed flotation tailings from the adjoining 350 tpd (3.67 kg/s) silver-lead flotation mill. Changes to the dredge reclaimer, pulp storage tank and trash removal system have allowed an increase in tonnage treated to a sustained 460tpd (4.83kg/s). CIP feed is 3-4 oz/T Ag (102.9-137.1 ppm). Following conventional cyanidation, carbon is added to the slurry. Silver loaded carbon is stripped in atmospheric-pressure vessels using hot caustic cyanide. Silver recovery from this solution is by Zadra- type cells. Some of the modifications to the plant and operating techniques are discussed.

Jan 1, 1981

By John W. Leonard

The typical tunnel boring machine in use on today's tunnel project uses 15'2-inch diameter cutters at a nominal load of 45 kips per cutter. The cutterhead rotates at a speed of 120 over D revolutions per minute where D is the cutterhead diameter in feet. The typical machine operates about 50 percent of the time. Delivery of a new machine takes 12 to 15 months. The TBM is a specialized tool and not applicable to all jobs. There is a range of job conditions that limit the economic use of a TBM. The machine should provide a thrust per cutter at least twice the compressive strength of rock in psi and up to three times the rock strength is required if in "granitic rocks." The rock strength in psi must be at least three times the cover above the tunnel in feet or the machine may stick. For example, 2,500 feet of cover requires at least 7,500 psi rock to avoid problems. When the RQD's over a significant distance of the project are less than 50, the TBM becomes support-bound. When a large percentage of the time is spent waiting while the ground is supported, the TBM cannot perform well (See Figure 1). This problem increased inversely with tunnel diameter. We are finding that increasing the RPM's does not significantly increase progress. The increased RPM results in a substantial decrease in cutter penetration. The explanation for this decrease appears to be vibration, cutterhead drag, or lack of stiffness in the cutterhead (See Figure 2).

Jan 1, 1981

By Peter G. Chamberlain

The Bureau of Mines is conducting research to boost domestic production of manganese. Virtually no mining exists in the low grade and/or small deposits that occur in this Country. One large, low-grade manganese deposit located in westcentral Arizona--The Artillery Peak district--was extensively studied and sporadically mined during the 1940's and 1950's. Although manganese mining in the district has been long dormant, recent studies indicate that the deposits may be amenable to economical production by heap and/or in situ leaching methods. A conceptual design for an in situ leaching system features undercutting and blasting a block of ore, leaching with SO2, and extracting the manganese as a sulfate or oxide. Possible applications to other manganese deposits depend upon formation permeability and specific manganese mineralogy.

Jan 1, 1981

By Michael H. Vallez

On September 13, 1973 MAPCO Inc. leased from Pocahontas Land Corporation an 18,000 acre tract of coal lands in Eastern Kentucky's Martin County (See Figure 1.). In July, 1974 initial run of mine coal shipments commenced and in April, 1976 shipments of a 12,500 BTU, less than 1% sulphur, washed coal was being shipped. Results of exploration demonstrated that large quantities of overburden would have to be moved. MAPCO decided to invest in large surface mining equipment to tackle the job.

Jan 1, 1981

By G. M. Clarke

Minerals are certainly where they are found. The undemocratic distribution of the world's mineral wealth has created an incongruous inbalance: mineral-rich, scarcely populated countries supply highly-populated industrialised countries that in turn consume more minerals than they produce. This has been as much a generating force for colonisation, invasion, and war as religion, political ideals, or megalomania. The Industrial Revolution of the seventeenth century was born in Britain, a country with large domestic resources of coal, iron, lead, zinc, copper, tin, etc., as well as a large population. As consumption outstripped production imports filled the gap, particularly from its worldwide colonies. For example, when Canada was founded in 1867 more than 905 of its investments were British financed, and much of these were mineral-based. The British made similar investments in South East Asia, Australasia, the Caribbean, and elsewhere, as did the other industrialised Western European countries hungry for raw materials. Later the United States emerged as a leading industrial power, again due largely to its abundant natural resources. Consumption soon exceeded production and foreign sources were saught. American business went exploring abroad ant many a mineral resource was developed almost totally on the basis of the US market many .thousands of miles away. Closer to home, Canada was also an obvious target for the US with its rich mineral resource base, small population, and geographical juxtaposition, so much so that about the time of the 1914-18 War the US took over from Britain as the major investor in Canada, and this peaked in 1967 when the US accounted for 80% of the country's foreign investment. After the 1939-45 War Japan joined the ranks of the USA and Western Europe as industrialised powers, and they too searched the world for the deposits lacking in their homeland.

Jan 1, 1981

By Dale D. Teeters

Today, I would like to talk about ways to maximize the efficiency of surface coal operations. I doubt I will present any startling new ideas, but my comments may, hopefully, stimulate some conversation today and later back at your own operations. Strip mining is a very old technique used by ancient societies. Only with the coming of the machine age in the early twentieth century did we attempt to increase the magnitude of our operations. The industry, as we know it today, really only got started in the early 1900s with the advent of steam shovels. In the first portion of this presentation, I will attempt to show that we have, in many cases, not changed the basics of strip mining, only the scale. In doing so, quite often we have complicated the operations to the point of being unmanageable and unprofitable.

Jan 1, 1981

By Robert R. Dorfler

AMPS[. has completed a rationed grinding ball test in a 2.93 m x 2.93 m ball mill at Climax Molybdenum Company. The test consisted of purging the ball distribution formed by charging 100%, 76 mm carbon steel balls with a distribution formed by charging 50% 76 mm and 20% 51 mm alloy steel balls. The resulting change in ball surface area yielded improvements in both tons ground and fineness of grind with a significant reduction in total ball consumption. This paper summarizes preliminary studies leading to the plant test, grinding efficiency results, and future plans to optimize the ball charge.

Jan 1, 1981

By Daniel F. Meyer, William C. Paschen

INTRODUCTION The problems involved with moving millions of tons of rock are being addressed by nationally recognized tunnel contractors who have converged in Chicago over the past 5 years. This wealth of expertise has been needed to meet the risk and challenge of constructing the world's largest network of underground tunnels which in turn has required a dramatic advance in the art and science of tunneling. These pioneers, through innovation, adaptation, and hard work, have eliminated the one major concern of The Metropolitan Sanitary District of Greater Chicago - how to move 8 million tons of rock. The Metropolitan Sanitary District of Greater Chicago (MSDGC) serves 122 municipalities covering 866 square miles in Cook County, Illinois. Of these cities, towns, and villages, 53 have combined sewer systems. On an average of once every four days, these systems overflow about 4 million gallons of combined sewage and rainwater into the area's rivers and canals. The overflows occur at approximately 640 outfall locations of which 10% are owned by the MSDGC, with the remainder of the points belonging to various other municipal bodies. All those who own these "point" sources of pollution are in violation of Illinois State and Federal regulations. To enable its member municipalities to come into compliance with State and Federal law, the MSDGC is implementing its Tunnel And Reservoir Plan (TARP). TARP is a regional solution to the problem of combined sewer overflow in the metropolitan Chicago area. TARP will greatly reduce the pollution of area waterways by intercepting the combined sewage and rainwater carried in the existing sys-

Jan 1, 1981

By Andrew Trusiak

Brunswick Mining, employing approximately 1600 employees, is located 40 km south of the city of Bathurst in north eastern New Brunswick. The mine has operated as two lead-zinc operations - the underground mine(No.12) and the open pit mine (No.6). The open pit orebody is presently being' mined by underground methods. It is expected that the No.12 mine will furnish the entire ore supply by the end of 1981. The flotation practice prior to 1971 has been described by Neumann and Schnarr(1) and by Erskine (2). More recently, the current flotation practice has been described by McTavish(3) and deals with some major circuit modifications between 1972 and 1978. The period 1978 to 1980 has seen the completion of. a major flotation cell replacement and expansion program for the No.6 concentrator, and the implementation of computer control in the No. 12 CuPb and Zn flotation circuits.

Jan 1, 1981