Search Documents

By Gordon M. Matheson

The factors which control chimney subsidence sinkhole development in weak rock were assessed by analyzing the characteristics of approximately 3000 chimney subsidence features along the Colorado Front Range. The area of study included features developed over abandoned mines in the Colorado Springs Coal Field, the Boulder Coal Field, and the Foothills District. The approximate locations of the areas studied are shown in Figure 1. Data were collected for sinkholes occurring over both room and pillar, and retreat mining areas in coal seams with a wide range of dips. The location, size, and approximate time of development of each sinkhole were documented. From these data, relationships were developed which describe the time rate of observable sinkhole development and the relative location of sinkhole development with respect to mined height, overburden thickness, and type of mining for relatively flat-lying coal seams. In addition, the observed locations of sinkhole development over steeply dipping coal seams were assessed for portions of the study area.

Jan 1, 1986

By John W. Conn, Harry C. Verakis

An explosion in an underground coal mine can have a devastating effect on the main fans used to provide mechanical ventilation. The Code of Federal Regulations, Title 30, Part 75.310 (CFR, 1992), specifies that each main mine fan shall be offset by at least 15 feet (4.6 m) from the nearest side of the mine opening unless an alternative method of protecting the fan is approved in the ventilation plan. Also, each main mine fan shall be protected by one or more weak walls or explosion doors. This paper presents venting and fan configuration designs which provide a comparable degree of safety for explosion protection. Design flexibility is enhanced and a means for consistency in safety judgements is afforded.

Jan 1, 1993

By Rodolfo V. de la Cruz

The stresses in the materials surrounding an underground opening are dependent upon the virgin stress field, the geometry of the opening and changes in boundary conditions as mining progresses. For most underground openings especially in coal mines, roof bolts are installed to help stabilize the opening. While most parameters in roof bolt design and installation have been thoroughly investigated, the effects of the initial stress field on the effectiveness of roof bolts have not been recognized. This paper summarizes the results of investigation of the effect of the initial stress field on the performance of mine roof bolts. Roof bolt installations are duplicated in the laboratory utilizing conventional roof bolt frame, commercial roof bolts and shells, mine torque wrench and encapsulated rock specimens for anchorage. A special and primary feature of the laboratory set-up is the addition of a loading system for generating stresses at the anchorage specimens. For this preliminary study, different levels of hydrostatic stress fields were induced at the anchorage specimen, instrumented roof bolts were installed in the usual manner, and the bolt load loss-with-time observed. Statistical analysis of data showed that the stress field at the anchorage horizon has a considerable influence on the performance of mine roof bolts, i.e. the higher the stress field, the higher the anchorage efficiency. From this observation, methods of improving the performance of mine roof bolts utilizing new shell designs and methods of installing them are suggested.

Jan 1, 1978

By D. Richter

The Pyrometallurgical refining stage of ferronickel manufacturing produces a slag rich in iron and nickel, which is usually further processed for metal recovery. The recovered material is returned to the refining or smelting stages, depending on the amount of impurities. A series of tests was carried out on the Mineração Morro Azul refining slags, aiming at the recovery of the metallic particles through physical processing. Minor changes in the process showed improved results. This paper compares the textures of these slags after being cooled at ambient temperature and granulated under water at high pressure and flow. It concludes that the cooling process is intimately connected to the work index of such slags, thus resulting in direct impact in operating costs.

Jan 1, 2011

By H. B. Charmbury

In Pennsylvania there are two distinct coal regions, bituminous and anthracite, in which the mining conditions and production trends are different. Bituminous mining is more mechanized, and production is increasing. This report is concerned specifically with the bituminous area. The bituminous coal industry apparently is facing a shortage of miners and mine officials which may become acute by 1970. Since 1949, when Pennsylvania had more than 100,000 bituminous coal miners, the number has steadily decreased. There are two principal reasons for the decrease of certified miners and mine officials. These reasons are the fact that apprentices are almost a thing of the past and the fact that the image of the coal miner is a poor one to people in general and to parents in particular. This has contributed greatly to the high average age of our miners today. The average age of all those employed in the mines is 50. Yet it is known that the progress in mine mechanization requires younger and more alert men to operate the newer type equipment.

Jan 1, 1966

By W. McMahon

Following the Sago Mine accident, the Mine Safety and Health Administration (MSHA) asked the U.S. Army Engineer Research and Development Center to study several possible methane explosion scenarios in the Sago coal mine. The study used a 1-ft resolution map of the mine to produce a 3-dimensional (3-D) model of a portion of the mine, including the sealed area where the explosion occurred. An advanced 3-D computational fluid dynamics (CFD) code was used to calculate the explosion pressures within the sealed area, on the mine seals, and in nearby regions of the mine. Based on the best available information on methane concentrations and assumptions on homogeneity and on layering and mix composition, three separate initial conditions of methane-air concentrations and location were studied. This paper discusses the CFD modeling technique, the results of the calculations, the challenges of conducting this type of modeling, and the advantages and limitations of CFD modeling of accident investigations of mine explosions.

Jan 1, 2009

By George C. Toland

Most existing impoundment ponds and dams leak effluent into the soil or rock upon which they are constructed. However, proposed environmental legislation will require very stringent control on the release of toxic effluents such as cyanide. More exacting investigation, design, and construction techniques than have been used in the past will be required to satisfy these new regulations. This paper discusses the types of field and laboratory investigations required to develop the data for the design of an impoundment system containing toxic effluent, and discusses in detail technical considerations necessary to design this system. Design topics include reservoir sealing with natural and man-made materials; embankment sealing; embankment design considering stability, surface hydrology, capacity, and downstream catchment basins; and special implications of cyanide effluents.

Jan 1, 1975

By M. P. Neira

In-situ leaching of copper from chalcocite relies on ferric iron concentration in the lixiviant being reduced to ferrous. To re-establish the ferric concentration in solution, ferrous must be re-oxidized. This reaction is slow under normal chemical conditions but it is catalyzed by Thiobacillus ferrooxidans bacteria. BHP Copper's Miami In-situ unit developed a bio-reactor as a method of oxidizing ferrous to ferric. The effects on oxidation of temperature, CO2? oxygen, and air injection flowrate were defined. This paper summarizes the results of ferrous bio-oxidation using plastic column packing and oxide ores as bio-reactors and the leaching results of the bio-reacted lixiviant on chalcocite ores.

Jan 1, 1997

By E. S. Peterson, M. K. Harrup, K. A. Dolbeare, J. E. Wey

Efficient methods for the removal of copper from heap-leach solutions without mobile organic phases are a current mining industry need. To satisfy this need, a selective, high-capacity, durable solid material is required. The Idaho National Engineering and Environmental Laboratory (INEEL) developed a set of materials based on current solvent-extraction chelates that provide selective copper concentration in the presence of high concentrations of iron. In contrast to conventional solvent extractions, the author's strategy anchors the chelators to a nonpolymeric solid substrate through the use of a custom-designed linker molecule. The fundamental synthetic routes to these materials have already been established, and attachment to the solid surfaces have been achieved in an efficient manner. The author's continuing research is focused on the optimization of the synthetic pathways to these solid materials and the evaluation of their copper-capturing capabilities.

Jan 1, 2003

By R. D. Lawrence

Suggestions have been made that the appraisal of mining assets using discounted cash flow techniques should be based solely on proven and probable reserves in reliance upon the widespread international recognition of uniform resource definitions. Following a review of general accepted valuation principles, a survey of the literature and, most importantly, a review of real transactions in the open market, it is clear that valuators should not be constrained by the growing acceptance of modern mineral resource codes. On the contrary, valuation practitioners should be encouraged to examine all classes of mineralization and, after making due allowance for risk, to utilize all mineral resources as a basis for determining fair market value.

Jan 1, 2000

By B. F. Westfall

Throughout the 1960's and 1970's world trade grew rapidly, reaching a peak of USS1.8 trillion in 1980. Since then the world recession of the early 1980's shrunk trade to about US$1.6 trillion. The reduced cash flow to developing economies made it difficult to service their huge international debts, Nowadays lenders are reluctant to grant Third World countries additional credit. The shortage of export financing, plus trade barriers set up by developed countries, is further inhibiting international trade. Therefore, countries are turning to new and creative alternatives to financing imports of consumer as well as of investment goods. Non-cash transactions, including different forms of countertrade, are rapidly growing alternatives to traditional trade financing patterns. In 1983 about 30% of international trade, or close to US$600 bill ion, were presumably done by non-cash transactions, up from barely 2% in 1976. By year 2000, half the world trade is likely to be conducted on basis of barter. As of mid-1984 some 88 nations used countertrade regularly and Governments of at least 15 Latin American countries had arranged or mandated commercial countertrade.

Jan 1, 1986

By K. V. Raj

"The development and advancement of computational fluid dynamics (CFD) has made it possible to better understand pollutant flow and distribution in deep open pit mines. Open pits located at higher latitudes, especially in the Arctic and sub-Arctic, face a unique problem due to atmospheric temperature inversion, which is prevalent during much of the winter. A three-dimensional CFD model of an actual open pit mine in the Arctic was developed to analyze the problem of pollutant growth during inversion, and mitigation of the pollutants through improved ventilation schemes. Due to the availability of mine-specific data, such as contaminant concentrations and coordinates of sampling locations, the actual 2013 pit geometry was used for model validation Concentrations predicted by the selected realizable ?-e turbulent model are compared to measured pollutant concentrations at the open pit. Pollutant concentrations at selected locations showed differences, but remained within the same order of magnitude in most cases. INTRODUCTION Computational fluid dynamics (CFD) has emerged as a useful tool for ventilation modeling in underground mines (Edwards and Hwang 1999, Purushotham and Bandopadhyay 2009, Wala et al. 1998, Xu et al. 2011). Application of CFD in open pit mines has been limited, however, since most open pit mines located at lower latitudes do not encounter considerable ventilation problems. Open pits located at higher latitudes, especially the Arctic and sub-Arctic, face a unique problem due to atmospheric temperature inversion, which is prevalent during winter. A number of Russian researchers have tried to understand the air inversion and resulting pollutant transport problem by modeling air flow phenomena in open pit mines (Baklanov and Burman 1996, Baklanov 1984, Baklanov 1995, Belousov 1985, 1989, 1995). Much of their work, however, was based on numerical models and methods of finite difference. Baklanov (2000) applied a modified ?-e and a ?-l CFD model to air flow phenomena on various terrains. More recently, Choudhury (2011) used the COMSOL CFD package for modeling pollutant transport for an idealized open pit mine. Collingwood et al. (2012a, 2012b) used a two-dimensional model for fluid flow and contaminant transport at an Arctic open pit mine. The authors have also previously presented work on CFD modeling of an actual open pit mine at high latitude (Bandopadhyay et al. 2014, Raj et al. 2015a). However, the CFD work done by the above-cited researchers lacked model validation with field-measured data. Validation of a developed model is important in assessing the quality and accuracy of the predicted results. In general, experiments are done numerous times in controlled environments to assess the validity of collected data. There are two types of assessments used in CFD simulations: (1) verification and (2) validation. Model verification is checking the accuracy of the computer codes during the implementation phase of a real-world problem, within the specific limits of accuracy (Oberkampf and Trucano 2002). Since, the pollution transport model presented in this paper used the commercial ANSYS-FLUENT CFD package, verification is not needed as the program has been tested widely, and verified numerous times."

Jan 1, 2016

By Werner A. Ruemmele, Steven R. Wardwell

INTRODUCTION The first phase of the Los Angeles Metro Rail Project consists of 7.1 km (4.4 miles) of subway and stations running through downtown Los Angeles from Union Station to MacArthur Park. Shank-Ohbayashi has two of the tunnelling contracts on this initial phase: A-171 and A-146. Contract A-171, the Wilshire/Alvarado Line, involves tunnel construction beneath 7th Street from the 7th/Flower Station to the Wilshire/Alvarado Station. The project consists of the excavation and lining of 3000 m (9900 ft) of twin-bore, 6.7 m (22 ft) excavated diameter, 5.5 m (18 ft) finished diameter subway tunnels. Contract A-146, the 5th/Hill to 7th/Flower Tunnels, comprises 1220 m (4000 L.F.) of twin-bore tunnel identical in cross section to the tunnels in Contract A-171. The majority of the excavation on Contract A-171 is beneath city streets in a weak siltstone/claystone bedrock with cover varying between 10 m and 25 m (32 ft and 82 ft) to the street surface. Approaching the 7th/Flower Station some fine-grained alluvium is encountered. The tunnels on both contracts are excavated with an open face digger equipped shield. On Contract A-146 the tunnel alignment is a 305 m radius curve of approximately 550 m (1800 L.F.) length underneath several multi-storied buildings of various construction. Excavation is still ongoing on Contract A-146. The contractor's choice for initial tunnel support on both contracts is a system of precast concrete segments similar to what the contractor had used on 7 miles of tunnel in Phoenix, Arizona, for the Arizona Department of Highways.

Jan 1, 1989

By V. L. Magnus

The text of this chapter was not received in time for printing.

Jan 1, 1979

By J. Torma-Krajewski, C. Hipes

Many mining companies apply ergonomic principles, but it is done either informally and/or reactively. Examples of an informal approach include replacing worn equipment, such as seats, with models that have ergonomic features, or modifying tasks to eliminate safety hazards that will also reduce risk factor exposures that may result in musculoskeletal disorders (MSDs). A reactive approach is followed when modifying a task/equipment after an MSD occurs. Neither one of these approaches involves a systematic method of proactively applying ergonomic principles to actually prevent injuries or illnesses. This paper will discuss how Vulcan Materials Company applied ergonomic principles and the interventions implemented to reduce risk factor exposures.

Jan 1, 2007

Adsorption of acrylamide based homo and copolymers on hematite was investigated as a function of phe nature of the polymer charge and functionality of the polymer. Effect of addition of sodium dodecylsulfonate and dodecylamine hydrochloride was also studied and was determined to result in an increase or decrease in the amount of polymer adsorbed depending on, the charge characteristics of the surfactant and the polymer, pH of the suspension, concentration of the various species and the order in which these species were added to the system. The surfactant adsorption under given conditions on the other hand, was found not to be affected by the presence of the polymer molecules. The data is analyzed to elucidate the mechanism of adsorption of polyacrylanide type polymers on hematite both with and without the surfactant species king present in the system.

Jan 1, 1982

By Janusz Cygankiewicz, Marian Branny, Józef Wactawik

The paper presents mathematical model of concealed fire. We consider a porous medium (goaf, coal fissures) through which air flows. The set of equations is constituted by transient, two dimensional mass, momentum and energy balance equations with sources describing oxygen loss and heat generation caused by coal oxidation. Paper presents several examples illustrating the phenomenon of spontaneous heating in goaf areas behind longwall faces.

Jan 1, 1997

By K. McG. Bowling

A statistically-designed exper¬mental study showed how gangue minerals, flux additions, fineness of grind, firing temperature and time affect the properties of acid pellets made from a Western Australian hematite ore. Alumina has less effect than silica and lime, but various interactions between the six variables occur, which influence abrasion index, reducibility and cold compression strength. Finer grinding has little influence on reducibility but improves the other two properties. The major variable is firing temperature. It interacts with all other variables in its effects on pellet properties. Calculations based on the data show the implications for straight-grate pellet plants and optimum hood temperature range.

Jan 1, 1980

By D. S. Dinsmoor

Boron, estimated to comprise about 0.001 percent of the earth's crust (Fleischer 10), as an element is never found free in nature, although its compounds are found in many localities. the borates are the most important. Sassolite (B(OH)3) and boracite (Mg6C12B1406), non-borates, are-of-minor importance. The crystal structures of most natural borates are still unknown. A classification based solely on the ratio of boron to the total number of cations has been devised (Palache 28). This classification divides the borates into four, sub-groups; anhydrous borates, hydrated borates, borates containing hydroxyl or halogen and compound borates. Only four or five minerals of the hydrated borates group have ever been used commercially. In more recent years, the sodium borates have comprised all but a 'small fraction of all borates used. Borax, the hydrated borate compound, is the most important of all boron compounds. It has been used so long and so often that the layman often confuses borax and boron and, applies the terms synonymously.

Jan 1, 1958

By Graham Taylor, Mandy Agnew

Hardpans developing in tailings storage facilities (TSF) in Australia have been investigated in relation to Acid Rock Drainage (ARD) generation. This research had three main aims. Firstly it was to obtain an understanding of the physical and chemical characteristics of tailings residues which support the in-situ formation of cemented layers and hardpans. Secondly it was to examine how effective hardpans are at reducing ARD generation, and thirdly it was to investigate the promotion of hardpan formation to inhibit ARD and pollutant generation. This paper presents the data collected during investigations into the effectiveness of hardpans to reduce ARD generation. Three basic types of hardpans have been identified and examined: laterally extensive surface hardpans, laterally extensive cemented layers; and laterally discontinuous hardpans developing in locations of seepage. Their mineralogy, morphology, lateral extent, depth and rate of formation are dictated by sulfide and gangue mineralogy and content, milling and depositional techniques of the tailings and the climate. As the sulfides oxidise, acid and heavy metals are generated, while gangue mineral degradation is enhanced, adding to elemental loads. These liberated ions are then available for precipitation of secondary mineral cements through concentration during evaporation. In TSFs where hardpan development is restricted by mineralogy, grain size or climate, hardpan formation can be enhanced in seepage zones (eg. seepage from waste rock dumps) where tailings are exposed to seepage waters laden with heavy metals and sulfate. The effectiveness of hardpans in the inhibition of ARD generation is dependent on reducing oxygen diffusion and water infiltration into the underlying tailings. A reduction in water infiltration will diminish the transport of contaminants developed during sulfide oxidation and subsequent reactions. Water and gas movement through the hardpans at the CSA (Cu, Zn, Pb) and Elura (Pb, Zn, Ag) mines has been investigated. Permeability tests indicate the hardpans have reduced the infiltration rates by 10 to 100 times that of the fresh tailings. Oxygen diffusion rates were calculated and were shown to be up to 1000 times lower in hardpans than in fresh tailings. Such decreases are explained by persistent elevated 'degrees of saturation' within the hardpans. These conditions were verified using a conceptual model of sulfide oxidation reactions, which allowed comparisons of diffusion coefficients with modelled and observed depths of oxidation within the tailings impoundments.

Jan 1, 2000