Search Documents

By R. J. Matetic

The impact of longwall mining on the local hydrological regime has become an important environmental focal point. Unfortunately, only a few studies have addressed the timing and range of well fluid level fluctuations and the associated ground movement. Furthermore, even fewer studies have determined the influence of longwall mining on water quality. The U.S. Bureau of Mines is providing insight into this environmental concern through a program of field case studies. One such study was conducted in Cambria County, PA where five observation water wells were drilled above two adjacent longwall panels. In this study, three wells were completed as nested piezometers and the remaining two served as producing wells. The piezometers were positioned along a line oriented subparallel to the longwall face and were located at the centerline of each panel and over the intervening chain pillars. The piezometers were designed to monitor fluid level fluctuations in both shallow and deep water-bearing zones. Slug tests were conducted before and after mining to characterize changes in hydraulic conductivity of the respective water-bearing zones. Pressure transducers and data loggers were installed to provide continuous fluid level fluctuation data as mining developed through the study area. The producing wells were drilled to provide water quality information. One well was located directly above the centerline of a panel and the other was positioned over the panel's set-up rooms. The wells were designed to simulate domestic use and were produced daily, for four hour intervals, throughout the study. Samples of the produced water were collected before and after mining progressed through the area. In addition, an array of monuments was installed near the study wells and was periodically surveyed to characterize mining-induced surface deformations. This study shows that: a) the observed changes in ground water chemistry did not affect the potability of the water; b) short-term major water level fluctuations occur at the approximate time of undermining; and c) water level recovery begins before the process of subsidence is complete.

Jan 1, 1986

By J. J. Carlson

Studies were carried out to determine whether filtration rate changes observed in an iron ore concentrator were due to variations in particle shape. It was confirmed that ores mined from different locations differed in filtration rates by as much as 60%. However, when image analysis was used to quantify the shapes of the individual particles in the filtration feed, it was found that the particle shapes showed almost no variation, and the shapes did not correlate with the filtration rate. It was also determined that the filtration rate variations were not caused by changes in particle size distribution. These results suggest that the differences in filtration rate are due to factors other than size and shape, such as surface chemistry.

Jan 1, 2008

By P. A. K. Wilkinson

This paper is concerned with the development of an in situ recovery of boric acid from a deep-seated colemanite deposit in California. The deposit contains 147 million tons of borate ore containing 6.4% boron oxide (B203). It is the largest undeveloped colemanite deposit in the United States and because of its unique occurrence and grade, in situ extraction appears to be the most economic viable process. The paper covers the geological, mineralogical, hydrological, well-field development, and extraction considerations leading to the initial pilot plant and subsequent demonstration plant phases of the project. Market potential aspects and preliminary economics of the project are also covered.

Jan 1, 1987

By M. Sengupta

Surface mining in arctic regions is characterized by many unique problems. Continuous and discontinuous permafrost (perennially frozen ground) occurs in most of the arctic and subarctic areas. Permafrost presents special problems of slope stability. Stability of permafrost depends on its temperature, moisture content and material type. Permafrost slope fails due to solifluction, disturbance of ice rich slopes, and liquefaction. Drilling and blasting of frozen ground present special problems. Depending on their degree of saturation with water, freezing soils and rocks have a number of important characteristics that affect blasting efficiency. Metals used in mining equipment and mining structures require special selection. At low temperatures many steels lose most of their normal ductility and toughness (resistance to brittle fracture). The paper discusses engineering solutions to unique problems of arctic mining.

Jan 1, 1986

By E. Kokinou

The main scope of the present study is to investigate the suitability and sensitivity of the magnetic susceptibility as a pollution monitoring tool in urban areas. For this purpose, a municipal park located in the centre of Chania city, which may be affected by traffic and domestic heating pollution, was selected as the study area. In the context of the present work, magnetic susceptibility measurements were conducted in two phases. Surface soil samples were collected in 2006 from the area under investigation and they were analyzed in order to estimate the spatial distribution of the magnetic susceptibility. One year later, mapping of the magnetic susceptibility has been contacted in situ using Bartington MS2D and MS2F sensors. Additionally, soil samples were collected from selected positions in order to compare the values of the magnetic susceptibility with that estimated in 2006 research. Both investigations indicate high values of the magnetic susceptibility around the park near the roads and in a small area inside the park where a café is located.

Jan 1, 2008

By J. Jeffrey Wagner, Michael J. Bailey, Peter M. Douglass

The Chambers Creek Interceptor Sewer Tunnel project consisted of 2-1/2 miles (4 kilometres) of nominal 9-foot (2.7-metre) O.D. tunnel driven through predominantly glacially overridden soils. Mole-Collucio Construction Company initially elected to drive the entire tunnel with a Lovat TBM. However, this machine could not control the fast raveling ground conditions which developed when the TBM encountered sands overlying very dense, hard glacial till or boulders. As a result, a shield and digger machine was brought in for a 1700-foot (518-metre) long segment. Pumped wells spaced roughly 50 to 125 feet (15 to 38 metres) apart were utilized to dewater about two-thirds of the alignment during construction. Initial support consisted of steel ribs and wood lagging, with a final lining comprised of pre-cast concrete pipe segments grouted in place.

Jan 1, 1985

By Harold Bloom

The Mount Pleasant Mines, or Mount Pleasant Joint Venture as it is presently known, is located approximately 59.5 km (37 miles) south of Fredericton, NB, Canada. Earliest indications of mineralization were found in 1954, during a regional reconnaissance geochemical stream sediment survey carried out over large parts of New Brunswick and the Gaspé Peninsula. The regional geology of New Brunswick is shown in Fig. 1. This program, sponsored by Selco Exploration Co. Ltd. of Toronto was conducted by H. Bloom, H.E. Hawkes, J.E. Riddell, and J.S. Webb. At its conclusion in 1955, 30 significant anomalous drainages were identified for follow-up evaluation. A total of 4937 sample sites were occupied. Geochemical reconnaissance using stream sediment sampling was a new technique which had only been field tested the previous year in the Gaspé and the northern coastal area of New Brunswick. Sediments collected from known mineralized drainages were found to leave a train of anomalous heavy metals from 1.6 to 9.7 km (1 to 6 miles) in length. When the exercise was extended to a reconnaissance survey, the previously unknown mineralized prospect at Nash Creek, New Brunswick, was discovered, staked, and later drilled (Hawkes and Bloom, 1956). Although it did not come into production, the discovery left little doubt as to the viability of the method and led to the Selco sponsorship of the program for the following two years.

Jan 1, 1991

By Djavid Mohammad

Over the next several years, the storage capacity of the Metropolitan Water Reclamation District of Greater Chicago?s Tunnel and Reservoir Plan will be increased by 14.8 billion gallons through the addition of two large off-line reservoirs: the McCook and Thornton Reservoirs. The Thornton Reservoir will be constructed at the terminus of Calumet TARP System. The constructed TARP system will be connected to the Thornton Reservoir via connecting tunnels and gates systems. The connecting tunnels will comprise of: an upgradient transition tunnel, steel lined bifurcated tunnel for conveyance and control of flow, downdradient transition tunnel, and energy diffuser at tunnel portal. A large, approximately 250-foot-long, 69-foot-wide, and 40-foot-high, rock cavern will be excavated at an average depth of 320 feet to house the bifurcated tunnel system and associated six large control gates, each 12.5-ft by 28-ft wheel gate. Presented in this article are discussions about the TARP system, the Connecting Tunnels and gates Project, regional rock conditions, evaluation of reservoir?s wall stability for evaluation of tunnel penetration, and design challenges facing during design of the: rock cavern hosting the bifurcated tunnel system and gates and associated tunnels and shaft.

Jan 1, 2008

By W. A. Lawruk, L. J. Wilson, D. E. Stief

The Tower mill is a vertical stirred mill using steel balls or pebble grinding media. This device is designed for fine grinding at significant power savings when compared to conventional tumbling mills. This paper describes the machine and its operation, application, and performance for wet grinding.

Jan 1, 1988

By Thomas F. Martin, Daniel J. Sieve

In April 1988, the joint venture of Morrison-Knudsen and Paschen Contractors (M-K/P) was the successful low bidder for the Metropolitan Water Reclamation District of Greater Chicago's (MWRD) Contract Number 73-164-2H. This project is yet another in the MWRD Tunnel and Reservoir Plan (TARP) devised to control and treat overflows from combined sanitary and stormwater flows. M-K/P's project, located along the Des Plaines River, consists of 21,569' of tunnel mined to a 35' diameter and two tunnels totaling 14,529' mined to a 12' diameter. All three tunnels will have 12" thick reinforced concrete lining. The path for combined sewer/storm waters to reach the tunnels begins at a connection structure, continues through an approach sewer, a sluice gate structure and down a vertical shaft which is topped by a backflow structure. The purpose of the backflow structure is to prevent water surging to the surface as the system fills rapidly. Backflow preventors represent a change in design after problems developed on earlier constructed portions of the T.A.R.P.. On this project, 14 drop shafts channel flows to the tunnel system. In addition to the drop shafts, contract specifications require an emergency or escape shaft be located not more than 4000 feet from the tunnel headings. Due to long reaches without drop shafts, four access shafts had to be constructed. Thus, the total shafts constructed under this contract will be eighteen plus one 30' finished diameter construction shaft located within Miller's Meadows. Figure 1 shows the overall Des Plaines River System and the M-K/P contract connection to previous and future MWRD projects.

Jan 1, 1991

The design of solvent extraction plants has been generally based on the assumption of steady operating conditions in both the settler and the mixer units. However, recent experience in both large and small plants has shown this not to be the case. Mixer transients include start up aqueous locking and partial phase separation in secondary mixers, which both lead to reduced plant capacity or overflow of upstream mixers. Analysis of the hydraulic pressure profiles has generated new design methods to eliminate the effects of the partial or complete phase separation. Changes to the method of specification and selection of primary and secondary mixers have been made to eliminate the onset of partial separation during operation. The observation of settler operation has shown that it is also a dynamic process, even under "steady-state" conditions. Four transient phenomena have been identified that lead to internal circulating flows, poor disengagement of fine secondary haze and erratic and high entrainment levels in the discharges. A, first approximation analysis has shown that there are significant pressure differentials within settlers, and these change along the length and with the phase separation rates. A technique to control the effects of these transients was developed that allows plant performance to be improved beyond "standard" expectations. The design and selection of the settler internals is described. Key words: Solvent extraction, Mixer-settlers, Phase separation, Entrainment, Mixer transients

Jan 1, 2003

By R. W. Barbaro, R. V. Ramani

Generally, production planning is concerned with the best use of fixed resources to determine a production schedule for one or more production units supplying one or more markets. Production scheduling determines when each production unit will be used and its production level. However, the production scheduling problems are intimately associated with the location of existing or new production units and processing facilities. Normally, mine location allows only a limited choice; processing plant types and locations are considerably more flexible. This paper presents a generalized multiperiod MIP model as an aid in determining the mine production schedule and the processing plant types and location to satisfy multiple markets. A brief description of MIP and how it has been applied in the mineral and other industries is discussed. A complete description of the model with an application to a coal preparation plant system is presented.

Jan 1, 1987

An open pit production planning method for stage mining is presented in this paper. The method brings solutions to the four most important parameters in stage mining : 1) the number of stages, 2) the size and geometry of each stage pit, 3) the mining sequence of the benches in the stage pits, and 4) the time of transition from one stage to the next. The method can also simultaneously optimize the ultimate pit, mine life, and production rate in each stage.

Jan 1, 1996

By K. Short

Today?s modern mining operations have literally dozens of applications and systems generating data whose information very often, are not crossed or centralized for operational decisions. In remote locations, the information and situation awareness is typically limited to the location itself. In addition, access to that information is limited to a small, select group of personnel that have received training on how to interpret the results. When the situation affects another area of the mine then information is relayed to the applicable areas involved. Few workers have time to analyze the situation thoroughly, to see how it affects the mines symbiotic relationship within all areas of production. If the capability to correlate and measure events and situations that affect your overall key performance indicators are not in place, the opportunity to identify process improvement becomes more difficult.

Feb 27, 2013

By G. Danko

MULTIFLUX, a new thermal, hydrologic, and airflow model and software is being developed to solve the flow of heat, moisture, and air in and around an underground opening. MULTIFLUX couples two distinct domains that are solved separately first and re-coupled as an iterative task: (1) the rockmass, and (2) the airway. The airway is solved with a lumped-parameter Computational Fluid Dynamic (CFD) module which is an embedded part of the MULTIFLUX code. The CFD model includes convection, conduction, and radiation for heat, as well as convection and diffusion for moisture transport in an air-filled opening. The CFD model also solves for the airflow field. The surrounding rockmass model may be from any analytical solution, or from a complex thermal-hydrologic numerical model such as NUFT or TOUGH2. The rockmass model is interfaced to MULTIFLUX using a novel technique called Numerical Transport Code Functionalization (NTCF). The method provides fast convergence on a personal computer platform. The paper reports the results of MULTIFLUX simulations for a mine drift, comparing calculations with a known mine climate software, CLIMSIM, and with measured data. Through this validation example, the performance of MULTIFLUX is demonstrated. The results show excellent agreement due to the use of realistic modeling assumptions and boundary conditions.

Jan 1, 2009

By J. D. Miller

X-ray computed tomography (CT) techniques have been developed for the medical services field in order to provide accurate internal images of the human body.(l-7) Now, a decade later, CT techniques are starting to be used in non-medical applications such as, non-destructive testing(8), flow pattern analysis(9), drill core examination (10,11), and coal characterization(12,13). In these fields of application, CT techniques offer the potential to extend our knowledge and understanding beyond that provided by more traditional methods of analysis. Although, CT systems involve very specialized and expensive equipment, the advantage of x-ray CT in revealing the detailed internal structure of an opaque material non-destructively should make it an important tool to provide a more complete analysis of mineral processing phenomena. X-ray CT systems generally consist of an x-ray source/collimation unit and a detector/data acquisition unit. The object to be examined is placed between the two functional units as shown in Figure 1. With this system the density array of selected cross sections of a chosen opaque object can be obtained in two dimensions. There are numerous areas in mineral processing to which x-ray CT technology can be applied and it is the aim of this article to identify these potential areas noting the advantages and limitations of the technology. Particular emphasis is placed on particle composition distribution and multiphase fluid flow measurements. In the case of particle composition distribution, liberation analysis and coal washability are considered. While in the case of multiphase fluid flow, swirl flow in the air-sparged hydrocyclone is given by way of example.

Jan 1, 1989

By Gregory E. Klosterman

American Aggregates Corporation is one of the leading producers of mineral aggregates in the nation. Production is from deposits of glacial sand and gravel and limestone and dolomite bedrock. Annual production from 33 plants is 25,000,000 tons. Land consumption is at the rate of 300 to 400 acres annually. This annual rate of consumption presents a continuing challenge to the exploration and mining personnel to meet the requirements of reserve replacement, mining and land rehabilitation.

Jan 1, 1974

By K. L. Lownie

For research and test data to serve a useful purpose, it is essential that it be derived from some known standard test procedure that allows for comparative analysis as well as independent replication and verification. Fan performance data provided by manufacturers is not absolute, and is influenced by the geometry of the test installation. For these reasons, fan test standards have been prepared in order to establish a clearly defined test procedure that allows for comparison of different fan designs, and also allows for the independent verification of test data. Internationally recognized Standards such as BS848, ISO5801, and AMCA 210 etc. are highly prescriptive, and precisely specify test duct configurations, measurement procedures, measurement planes and instrumentation to be used. Provided the laboratory tests are conducted strictly in accordance with the relevant Standard, the performance data will accurately reflect fan performance within the appropriate tolerances for efficiency, pressure and flow when tested in the defined configuration. Major differences in performance exist between a fan tested in accordance with a Fan Test Standard, and an identical fan installed in a mine ventilation system. The aerodynamic performance of any fan will be influenced by the quality of the fan manufacture, the flow system within which it is operating, the location of measurement planes, and the system stability. The flow distributions present in a standardized Laboratory test are unlikely to be repeated in mine ventilation systems, and this will also disadvantage fan performance. Unless the fan supplier takes all of these influences into account, there will an inevitable reduction in fan aerodynamic performance, and the end user will experience a shortfall in expected flow through the mine. The effect on fan performance can range from minor inconvenience to catastrophic fan failure resulting in major rectification costs and significant loss of mine production.

Jan 1, 2009

By Steven G. Vick

Effects of the August 1995 failure of the Omai tailings dam in Guyana continue to be felt throughout the mining industry. This article is taken from the final report of the independent body of experts commissioned by the government of Guyana to establish the cause of the failure. It explains what happened, why and how to avoid it in the future. Despite environmental, health and safety effects that were negligible by any objective measure, the failure has received wide international attention. Coming on the heels of the shift in exploration targets and development opportunities to developing countries, it has intensified interest in tailings dam safety and environmental management issues. An informed understanding of the nature of the failure and its effects is key to responding to these concerns.

Jan 1, 1996

By Giovanni Barla

The stress-relief method for the determination of the ground stress tensor is a common procedure in rock mechanics. In particular, the method of applying gauges to the end of a borehole is a well-established technique. Investigations, both experimental and theoretical, indicate that large discrepancies can exist in the determination of the ground stress tensor when the rock substance is not the ideal elastically isotropic material assumed for the reduction of data. The purpose of this paper is to extend the analysis of strain gauges applied to the end of a borehole to rock material more closely approximate to an orthotropic substance.

Jan 1, 1969