Search Documents

By J. G. Groppo

A series of performance studies have been conducted using counter-current column flotation to recover a marketable clean coal product from existing preparation plant fine waste streams. The test work was conducted at several preparation plant sites in Kentucky and Virginia and utilized a 0.15m (6 in.) I.D. column that was 5.79m (19 ft.) high. The refuse streams tested included both thickener feed and classifying cyclone overflow with a typical size distribution of 100 mesh X O. The percent solids of the column flotation feed varied from 1.5 to 15% while the ash content ranged from 30-60%. The concentrates produced contained 2-10% ash with BTU recoveries of nearly 90% using 0.12-1.25 kg/ton (0.25-2.5 lbs/ton) fuel oil and 0.12 kg/ton (0.25 lb/ton) MIBC. These results were consistent with or better than results obtained in preliminary laboratory scale column flotation evaluation. Test results from 7 different seams are discussed as well as scale-up relationships utilized to design a full scale installation presently in operation.

Jan 1, 1990

By William W. Wellborn

Abrasives are substances both natural and synthetic that are used to grind, polish, abrade, scour, clean, or otherwise remove solid material usually by rubbing action (as in a grinding wheel), but also by impact (pressure blasting). Facts about the discovery, early use, adaptation, and development of abrasives prior to the 20th century are few. From the sparse, earliest information that is available, it would appear that the science of abrasives began when, to fashion his tools, man began to select certain kinds of rocks in preference to others because of their peculiar properties. There is evidence that stones were sawed by some sort of grinding machine as early as 4000 BC in Egypt. The real expansion of abrasives use coincided with the beginning of metallurgy in the Middle East around 2000 BC. The earliest confirmed use of abrasives for grinding metal comes from a steel dagger found along with a sharpening stone which was dated at about 1500 BC. Natural and manufactured abrasive substances play an important role in fashioning and finishing numerous products with a wide variety of end-use applications. The mining and preparation of crude, natural abrasives for their markets and the manufacture of synthetic and other abrasive materials contribute significantly to the US economy (Table 1). In addition, just as sawing to specific dimensions enhanced the value of the Egyptian stone, the use of abrasives in fabrication of modem products, and the addition of abrasives to others, add value. GENERAL CONSIDERATIONS The most important physical properties of materials that qualify as abrasives are hardness, toughness (or rigidity), grain shape and size, character of fracture (or cleavage), and purity (or uniformity). To fabricate bonded abrasive products such as grinding wheels, additional considerations include stability under high heat and bonding characteristics of grain surfaces. The economic factors of cost and availability are always important. No one singular property is paramount for any use. For some applications extreme hardness and toughness are needed, as in diamonds for drill bits. For other uses, factors of greatest importance are hardness and ability to break down slowly and, in the process, develop fresh cutting edges when grains become worn. In garnet sandpaper, for example, highly cleavable, friable, or extremely tough grains are not desirable. For other uses, extreme hardness may be objectionable. Abrasives for dentifrices and for glass-cleaning soaps are cases in point. For the most efficient uses in more critical applications, different types of abrasives are rarely completely interchangeable. While crushed quartz and garnet are both used in sandpaper, the two abrasives are not at all interchangeable in their applications. In the final analysis, the choice of a high-grade abrasive depends upon the quality and quantity of work performed by the abrasive per unit of cost. Initial cost of an artificial abrasive may be much greater than that of a natural abrasive, but the artificial mineral may do so much better work and do it so much faster that the ultimate cost is less. It is for this reason that artificial abrasives have largely replaced natural abrasives.

Jan 1, 1994

By J. H. Bassarear, J. D. Vincent

General. Copper, the first metal used by man, today is the third in consumption after iron and aluminum. Compared to these it is relatively rare, with less than 0.01% of the earth's crust copper, 8% aluminum, and 5% iron. Nevertheless. our modern civilization is heavily dependent upon copper because of its high conductivity and resistance to corrosion, ease of working, durability, wide range of properties by virtue of its readiness to form alloys with other metals, and its attractive colors and texture that make it so desirable for many crafts and arts. These attributes explain why copper is chosen for a long list of uses, including electrical wiring, switchgear, and bus bars; piping, roofing, and siding; and manufactures of brass, bronze, and other alloys. The fact that copper ore is mined in nearly all parts of the world is significant. Its importance is shown in Table I, which gives figures on world production from 1968 to 1977. In the Free World, North and South America and Africa are preeminent. The table also shows the generally upward trend of production in this period; accurate figures for 1978 and 1979 from the same source are not yet available (1980), but it is certain that major environmental, economical, and political factors continued to disturb the industry in those years and into 1980.

Jan 1, 1985

Contents

Jan 1, 1985

The implementation of NAFTA in January 1994 was expected to have small but beneficial effects on the Mexican economy, mostly through increased investments. Mexico's mining industry was especially likely to benefit, as mineral investment funds would be diverted to the now safer Mexico and away from similarly endowed but more risky Latin American mineral economies. The results during the past two years have shown that it is government and macroeconomic factors that influence investment flows, rather than the fine tuning of trade flows through so called 'free-trade" agreements.

Jan 1, 1997

By R. K. Singhal

Canada is a world class producer and exporter of minerals and mineral products. It is also a major exporter of minerals. Canadian open pits are highly mechanized and use state of the art equipment and support technology. During the past few years significant productivity improvements have been achieved by taking advantage of larger equipment; in pit crushing and conveying; truck dispatch systems and electronic management tools. The most recent developments in Canadian Open-pit Mining are related to hydraulic transportation and the application of Global Positioning Systems. Mine planning is computerized; environmental issues are dealt with in all phases of planning; equipment modifications are pursued with vigor to keep them functioning in the hostile Canadian North.

Jan 1, 1999

By Mark E. Gershon

Extensive efforts are under way to- ward applying computer techniques to mine production scheduling problems. These efforts are concentrated in four areas: optimization, computerization of traditional methods, heuristics and simulations. These areas complement each other rather than compete. Characteristics of each are discussed toward enabling the engineer to evaluate specific systems that may be encountered. Alternative approaches within each classification are described as well as the motivation for each.

Jan 1, 1985

By Conrad W. Steller

What is the definition of a successful construction or development project? It could be described in many ways: a project that performs as designed; a project completed on time, a project completed within budget. The title of our talk today is, "The Advantages of Applying Design/Build -Construction Management to the Mining Industry." As our talk develops, you will see that rather than tell you how to apply this concept, we will discuss the advantages and details of Design/Build so that you can independently apply the concept. Design/Build is not new, and it cannot be universally applied. It has, however, within the past ten years, carved a specific and substantial place in the overall construction -development market. The reasons for its rather recent rise to considerable prominence as a concept is due, in part, to the increasing urgency of gaining productive access of a production facility and, in part, to the inherent advantages of the concept's economics--and they are considerable. If the Design/Build concept of contracting were fully understood, it would, without exception, be the favored way for private industry to contract for its new construction and development as well as renovation work. The basic advantages are: earliest possible access and completion at the lowest cost. Design/Build is often equated and compared to "fast track" or "turnkey" methods of construction. The Design/Build concept can, in fact, be both of these or neither. "Fast track", in and 6f itself, implies that the project will be phased construction, that is to say, it will be built quickly; whereas I "turnkey" is a measure of the completeness of the project, usually meaning essentially that the

Jan 1, 1977

The amount of hydrophobic materials constituting the mineral froth strongly influences the froth viscosity. Higher froth viscosity on the other hand can retard the drainage of physically carried over hydrophobic particles. In phosphate flotation tests a direct correlation was observed between froth viscosity and recovery and an inverse correlation between froth viscosity and grade. Phosphate flotation tests in the presence of a silica depressant indicated that higher froth viscosity is an effect rather than a cause of silica particles reporting in the froth.

Jan 1, 1992

By B. Fagerberg

Crushing and grinding practice in Sweden follows largely the international pattern. Certain special circumstances, however, have had an influence on the development. Most mines are worked underground in either quite small or in very large units. To utilize small sulphide ores, custom milling is rather common. Apart from the cement industry, the rock species treated are hard and abrasive. Another important factor is the increasingly strict requirements placed on the mechanical condition of different products, especially lump ores and coarse iron ore concentrates. A significant feature in the design and development of Swedish crushing and grinding practice has also been close cooperation between machinery manufacturers and the users. An account of these conditions and an outline of the crushing and grinding techniques employed in Sweden are presented in this paper with emphasis on the mining industry. For background purposes it may be mentioned that crude ore production in Sweden last year included 45 mill. tonsx) of iron ore, of which some 20 mill. tons from Kiruna alone, and 4 mill. tons of sulphide ore from 22 other mines, fig. 1. In addition 8 mill. tons of limestone were quarried for cement production and several million tons of stone and sand for roads, aerated concrete, etc.

Jan 1, 1968

By Sandip K. Mukherjee

In underground mining operations, ventilation and water sprays are the common methods of controlling dust. In recent years there has been a proliferation of technical literature dealing with water sprays for dust control. However, guidelines for the design of an effective water spray system have not been presented to the mining industry. This paper reviews developments in water spray dust control technology and recommends guidelines for water spray systems to control dust in under- ground coal and non-coal mining operations. These guidelines suggest type, number, location and orientation of nozzles, desirable operating water pressure, and associated filtration system.

Jan 1, 1983

By Cahit Helvaci, Robert B. Kistler

Borates are defined as ' 'salts or esters of boric acid; a compound containing the radical B203" (Bates and Jackson, 1987). Borates are defined by industry as any compound that contains or supplies boric oxide. A large number of minerals contain boric oxide, but the three that are the most important from a worldwide commercial standpoint are: borax, ulexite, and colemanite. These are produced in a limited number of countries (Fig. 1), dominated by the United States and Turkey, which together furnish about 90% of the world's borate supplies (Lyday, 1991). Production in the United States originates in the Mojave Desert of California; borax and kernite are mined by US Borax from its large deposit at Boron. Borate containing brines are pumped from Searles Lake by North American Chemical Co., and a limited amount of colemanite is mined by Newport Mineral Ventures from Death Valley. Turkish production is controlled by Etibank, the national mining enterprise, which supplies most of the commercially traded ulexite and colemanite from mines in the Bigadic and Emet Districts, plus borax from the huge deposit at Kirka. Borate minerals have been employed in a wide range of uses for many centuries, dating from at least the 8th century when they were used primarily as a flux for assaying and refining gold and silver. Their valuable properties and relative rarity soon stimulated international trade in borates; Marco Polo claimed to have trans- ported Chinese borate minerals from Tibet to Europe, and his home port of Venice was the center for borate imports and use throughout the Middle Ages (Travis and Cocks, 1984). Borates were traded at relatively high prices for highly specialized applications into the late years of the 19th century. At that time they were being used for medicines, food preservatives, ceramic glazes, and in expanded applications as metal fluxes. It was in that era that borax was discovered in Clear Lake, CA, and more significantly, the playa deposits of western Nevada were found and exploited by F.M. "Borax" Smith and others. Research and development by Smith's company began the evolution of borates from a high priced commodity with a few specialized uses to the relatively low priced chemical raw material used in large tonnages on a worldwide scale today. Borates are often defined and sold by their boric oxide or B,03 content, and most statistical data are listed in tons of B203. Of the products sold by the industry, borax pentahydrate or 5 mol and boric acid are the most commonly traded commodities. Boric acid plants are operated by all of the major borate producers. Glass fiber insulation is the major end use in the United States followed by textile glass fiber and borosilicate glass, detergents, and ceramics. Detergent usage continues to be a major end use in Europe.

Jan 1, 1994

By G. J. Hodges

The Stillwater Mining Company, a partnership of Pittsburg & Midway Coal Mining Co. and Manville Corporation, operates a precious metals smelter at Columbus, Montana to further up-grade concentrates from its platinum/palladium mine. The smelter began operation in the summer of 1990. The gas cleaning system in the facility utilizes "oxidation/dilute mode" dual-alkali scrubbing technology to capture sulfur oxide gases from the process gas streams. This paper describes the rationale for selecting the dilute mode dual-alkali system and summarizes design parameters. Start-up problems and their solutions are also discussed.

Jan 1, 1992

By A. B. Cecala

The US Bureau of Mines performed a study to determine optimal locations for longwall face methane monitoring equipment. Longwall face ignitions continue to be a concern to the US coal mining industry. Gains in ignition control technology have been somewhat negated by advances in longwall productivity. More reliable, heavy duty longwall face systems generate higher production rates and increase methane liberation rates. These rates will likely continue to rise as further coal production increases occur. Efforts will continue in the areas of methane drainage, methane containment and methane dilution. In addition, more effective face methane monitoring is needed. As technology continues toward automated longwall panels, the importance of monitoring for methane at the shearer becomes even more significant. Since the primary face ignition source is the shearer mining machine, the Bureau ran tests to determine the best location to take methane readings on the shearer. This information, in conjunction with data obtained from field studies, provides a knowledge base for selecting optimum face methane monitoring locations.

Jan 1, 1995

By A. S. C. Owili-eger

An efficient state-of-the-art dynamic model to simulate and predict the rate of water production in longwall coal mining operations was developed as a tool for mine planning purposes. The model can also provide an estimate of any potential resultant hydrogeological impacts of an operation via an array of element-specific single-valued parameters referred to as the field rating indices. The computational procedure was designed to fully exploit the benefits of hydrogeotechnology and utilize a combination of conceptual, physical, empirical, and numerical approaches to define, characterize, analyze, and evaluate flow con- trolling properties of fractured rock systems. The model presented here provides a dynamic prediction method for highly fractured flow; a practical tool in mine and water control planning; and a cost-effective means of assessing, based on the best available technology, the impacts of mining on the water resources within a mining environment to satisfy local and federal regulatory requirements. Unique features include consideration of laminar and non-darcian flow domains in double-porosity-pressure hydrogeological media.

Jan 1, 1987

By Raymond E. Krauss

The McLaughlin Mine is a world class epithermal gold deposit located in the coastal thrust fault of Northern California, U.S.A. Homestake adopted a proactive strategy in the permitting of the Mine. Extensive environmental baseline studies were undertaken. Engineering and process alternatives were evaluated for environmental impact along with other factors. A unique pressure oxidation process was selected. Screening studies were conducted as a basis for the selection of waste rock and tailings disposal sites. Project engineering and permitting were fast tracked. Construction required eighteen months, and the first gold bar was poured in March of 1985, six years after the initial discovery. Project facilities are designed and operated so as to minimize environmental impacts. A comprehensive monitoring program demonstrates permit compliance. Reclamation of the site is ongoing throughout the Mine's twenty year life. Nonmined lands are managed to maximize wildlife habitat value.

Jan 1, 1990

By Bennett D. Lass

A new method for determination of residual flotation oils on beneficiated kaolin clays has been developed. The method, which yields qualitative information, is based on fluorescence measurements employing a spatially resolved, polychromatic illumination source for excitation, and a two-dimensional detection scheme using a silicon-intensified, video imaging device. The method was used to identify residual oils on a beneficiated, Washington County, Georgia, crude clay. The results were compared to a similar qualitative analysis performed via capillary column gas chromatography using an FID detector. The video fluorometry was the preferred method of, analysis.

Jan 1, 1983

By J. R. Heberger

"“Safety Pays in Mining” web application developed by the U.S. National Institute for Occupational Safety and Health Mining Program, helps mines determine the potential costs associated with mining injuries. This web app groups injuries by type, either by the cause of the injury or by the nature of the injury. When the user selects one of more than 30 common types of mining injuries, the app provides information on the distribution of costs of workers’ compensation claims for that type of injury. Based on other user inputs, the app will estimate the total costs of the selected injuries, including an estimate of additional indirect costs, the estimated impact of total injury costs on mining company profits, and provide some examples of other items, such as services or equipment, on which companies could spend the savings that result from the prevention of injuries. This paper reviews the app by discussing its development, how it is used to show the true costs of mining injuries, and how mines can benefit from using it.IntroductionInjuries on the job cause pain and suffering. They can also profoundly affect profits and daily operations. In addition to paying direct costs or increased premiums for workers’ compensation insurance, a company might need to pay overtime for other workers to fill an injured worker’s job role, cover training costs for a replacement worker or divert administrative resources in the wake of an injury. “Safety Pays in Mining” is a web app that estimates the distribution of these injury costs and assesses the impact that occupational injuries have on a company’s profits.The costs of specific types of occupational injuries in mining are not readily available as mining and insurance companies do not usually share this information. As a consequence, companies only have cost information based on previous experience with their own employees. Therefore, if a mine never experienced a finger amputation for one of its miners, for example, it would not be aware of the possible costs associated with this type of injury. In addition, injury costs are unique in that the cost distribution is so wide that just using the average cost of a specific injury type does not provide adequate information. Some injuries involve immensely high costs, and even though the risk of these high-cost injuries occurring is low, mines need to be aware of the potential impact on their company’s financial health."

Dec 1, 2018

By T. E. Walsh

I will address two important alternative energy resources, solar and geothermal, with emphasis on their potential application in electric power generation. As a result of this presentation, I hope to leave you with a realistic view of the principal technology options that are being developed or that are available. Solar Types of Collection In terrestrial solar applications, the biggest challenge is to find ways of collecting the sun’s relatively low intensity energy so it can be converted economically to useful thermal or electric energy. Fig. 1 shows that there are both natural and technological ways of collecting solar energy. In nature we find that solar energy aids in the production of biological growth, rainfall, and wind, all of which can, in one form or another, be put to use in the production of heat or electric power. The sun’s rays also are collected and stored naturally in the form of heat in the upper layers of the ocean which can be put to use in the production of electric energy by means of ocean thermal energy conversion (OTEC) approaches. On the technological side, the sun’s rays can be intercepted by materials that directly absorb and convert its energy to low-grade heat, or by mirrors or lenses that focus the rays onto a material to produce high-temperature heat. The higher temperature systems can be used to drive efficient heat engines in the production of electricityy. The sun’s rays also can be collected on photosensitive materials, in either a direct or concentrated form to generate DC electricity directly. The systems I will discuss employ all of these means of collection and conversion, excluding biological and hydroelectric. The former is too exi

Jan 9, 1980

By R. Svensson

Mill linings play an important role in all comminution processes with tumbling mills. The selection of the lining profile and the lining material has a great impact on over-all grinding cost and mill throughput. The cost of the lining itself is minor in comparison with media cost, energy cost and the value of the material produced in the mill. The total scope must be considered when mill linings are selected. This paper presents case stories and explains the technology behind: -different lining profiles in rubber and steel -OREBED magnetic lining -Steel-cap rubber lining

Jan 1, 1994