Search Documents

By W. G. Pariseau

This contribution focuses on the role of stress analysis for mine planning and the selection of suitable computer programs for the task with special emphasis on coal mine pillars. In this regard, barrier pillars that defend a set of five main entries at the Crandall Canyon coal mine in central Utah were formed during extensive longwall mining north and south of these main entries. Numerical analysis for ground control guided the mine planning and permitting. Retreat mining of pillars led to disastrous events August 6 and 16, 2007, with the loss of nine lives. A most difficult lesson taught by the Crandall Canyon tragedy is the need for education in the selection and use of computer programs for pillar design. Much of this contribution is taken from a report prepared for the Mine Safety and Health Administration (Gates, et al, 2008). Details appear in Appendix Q of the report (Pariseau, 2008). The Crandall Canyon mine is about 16 miles west of Huntington, Utah, in the Wasatch Plateau coal field. Geology of the Wasatch Plateau is described by Doelling (1972) as gently dipping Cretaceous sandstones, mudstones, coal seams, and shales. Joint systems are present in strata above and below coal seams where cleat systems are present as described by Hucka (1991). Several major fault systems transect the field and form grabens with 450- 760 m of drop. One such structure is Joes Valley fault that crosses the Crandall Canyon mine. Mines in the Wasatch Plateau are generally developed from outcrops in steep canyon walls. Overburden increases rapidly as mining progresses into the plateau; mining depth varies with topography between 450 and 600 m in the region of interest. A stratigraphic column derived from a borehole into the mine is shown in Figure 1. There are 11 layers in the column.

Jan 1, 2011

By Daniel R. Stewart, Ralph R. Sacrison

The function of the geological engineer is to assist in mine planning and operations by collecting, interpreting, and applying geologic data to the solution of engineering problems. The geologist supports this effort by collecting additional geologic information specifically useful to the engineer. This use of geologic information reinforces the value of mine geology to the mining process beyond the traditional role of orebody definition. Work discussed includes: evaluation of caving strategies at the Climax and Henderson mines, support definition and slope stability at the Climax mine, and some uses of geology in cavability estimation for the Mount Emmons project.

Jan 1, 1992

By C. J. Bise

Virtual reality (VR) is a concept in which the human experience of perceiving and interacting with a computer-modeled environment is achieved through the use of sensors and effectors. It is an advanced form of computer graphics. The images are generated based on where the user looks and how the user moves. As personal-computer-based (PC) instruction gains acceptance as an innovative approach to providing safety training, VR can provide a multisensory, rather than merely a multimedia, mode of presentation. New technology continues to be introduced into the mining industry to meet the productivity needs of coal and noncoal producers. There is also an increased need for more innovative training of mine workers. New technology and equipment designs often affect the basic causes of accidents. For example, the development of cabs and canopies for underground coal-mine equipment has reduced the number of accidents related to roof falls and rib rolls. However, safety-training specialists then had to focus on the machines themselves, because the modifications had the potential for causing "pinch-point" accidents. In fact, although the overall physical demands on mine workers have diminished, there has been an escalation in the concerns about trauma from repetitive physical activity. Thus, health-and-safety training specialists have shifted their atten¬tion to the recognition, evaluation and control of workplace hazards (Hancock and Hill, 1995). Recognizing that the spatial relationships of a workplace convey more information about hazards when experienced rather than described, trainers agree that simulation is the method of choice. Unfortunately, until recently, simulation systems were either simple software programs that did not come close to portraying the real experience or were complex hardware systems (such as flight simulators) that did, but at a cost of millions of dollars (Fritz, 1991). However, researchers and training specialists are excited about an emerging approach to work-force education based on virtual reality. VR is also described as cyberspace, immersive simulation, artificial reality, telepresence, virtual environment or virtual world (Meyer and Dunn-Roberts, 1992; Peterson, 1992). It represents a group of concurrent advances in computer and interface technologies. They enable an individual to interact in a multisensory way with a computer-generated environment. To achieve this, a typical VR system incorporates a computer that contains the necessary databases for producing realistic images and audio; a head-mounted display (HMD) or screen for viewing the images; and a three-dimensional controller, joystick or data glove for interacting with the computer-generated environment. If virtual reality is to become an effective tool for the safety training of mine workers, its attributes will have to be measured against other forms of delivery. Accordingly, Carr (1992) listed the following areas in which VR should be considered the method of choice: ? When training mistakes would be costly. ? When the necessary environment cannot be experienced in the real world. ? To build interfaces that are sensible and can be manipulated. ? To make training situations really "real." ?To make perceptible the imperceptible.

Jan 1, 1997

By Roger Beckie, Leslie Smith, Craig Nichol

To study the hydrogeological processes that control the movement of water through unsaturated waste rock, an intermediate-scale (8m x 8m x 5m) waste rock pile has been constructed and instrumented. The constructed pile is monitored for moisture content, matric suction, temperature, matrix water chemistry, gas chemistry, gas pressure, rainfall, evaporation, discharge volume and discharge chemistry. The pile is built upon a grid of 16 contiguous lysimeters. The experiment is designed to investigate the mechanisms that create rapid water flow through a pile and its exchange with slower-moving matrix water.

Jan 1, 2000

By J. Navoyski, B. Macdonald, W. J. Helfrich, J. L. Bellanca, B. Demich

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the official position of the National Institute for Occupational Safety and Health, Centers for Disease Control and Prevention. Mention of company names or products does not constitute endorsement by NIOSH. ABSTRACT Recent advances in computing, rendering, and display technologies have generated increased accessibility for virtual reality (VR). VR allows the creation of dynamic, high-fidelity environments to simulate dangerous situations, test conditions, and visualize concepts. Consequently, numerous products have been developed, but many of these are limited in scope. Therefore, National Institute for Occupational Safety and Health researchers developed a VR framework, called VR Mine, to rapidly create an underground mine for human data collection, simulation, visualization, and training. This paper describes the features of VR Mine using self-escape and proximity detection as case studies. Features include mine generation, simulated networks, proximity detection systems, and the integration and visualization of real-time ventilation models. INTRODUCTION There are many definitions of virtual reality (VR) that include various levels of immersion and features [1]. Some definitions refer to specific technologies [2], while others are limited to visualization [3]. For this paper, a more general definition of VR will be adopted. VR is defined as the collection of hardware and software that interactively engages users and stimulates their senses within a synthetic or virtual environment. From a hardware standpoint, this can include anything from a phone to a head-mounted display (HMD) to a large-scale theater as well as speakers, microphones, haptic sensors, and interaction devices. The software used to create virtual environments (VEs) generally includes a game engine, custom software components and libraries, and two-dimensional and three-dimensional graphical assets. Recent hardware and software advances have increased the fidelity and availability of VR. New and improved technologies including HMDs and high-resolution monitors and projectors can display sharper, more detailed visualizations. For example, in the past five years between the release of the Oculus Rift DK1 (2013) and the HTC Vive Pro (2018), there was a three-fold increase in resolution along with a 50% increase in the refresh rate. Furthermore, despite early claims that low-cost VR technology was readily available [4], computational power has not been sufficient to handle the large amount of data generated by these systems [5]. In the past five years, however, rendering speeds have more than doubled and memory has more than tripled [6], allowing these visualizations to be incorporated into higher-complexity and -fidelity VEs that more closely mirror the real world. Similarly, software capabilities have also significantly improved through game engine advancements and feature development. In the past several years, game engines have added and improved features such as physics, lighting, platform support (e.g. Android), and asset development integration. Some of the current leading commercial game engines are Amazon Lumberyard, CryEngine, Unreal, and Unity, but this can quickly change as is evident in the literature [7, 8].

Jan 1, 2019

By F. Gray

The industrial diamond review arrived too late for the June issue. Since the economy is showing a resurgence of strength, diamond tool consumption is similarly on the rise. Tool makers indicate that sales are picking up. They expect that 1994 will see about an 8% increase. Fabricators expect this positive trend to continue through 1995. In the industrial sector, sales of grinding wheels, honing stones, cutting tools and the like are expected to grow 5% and 8% during the next year. Users still are buying only those products necessary for "just-in-time" production cycles.

Jan 1, 1994

By Robert L. Sundeen, Richard V. Wenberg

Service vehicles, often called support vehicles or auxiliary vehicles, are used in secondary functions to support production activities such as loading, drilling, and timbering. Probably the most common support vehicles are the personnel carriers used to move miners to and from work areas. Utility designs are used to transport supplies and various less mobile equipment. Specific application designs are used for special work such as explosives transportation and loading, equipment maintenance, and equipment lubrication. PERSONNEL CARRIERS Personnel carriers are available in a wide variety of sizes and configurations. Some are two-wheel drive, though most are four-wheel drive. Smaller versions carry at least two men and usually have sufficient capacity to carry a small payload of supplies or equip¬ment. The American Motor's 05 Jeep, equipped with an optional diesel engine, has been adapted successfully for this light duty. Larger personnel carriers with ca¬pacities of 12 to 20 or more men currently are available, as shown in Fig. 1. The designs often are customized to the operating characteristics of each mine. All meet the latest federal requirements for rollover protection, emergency brake systems, etc. UTILITY VEHICLES Utility vehicles are adaptable to numerous duties. Probably the most common are ordinary haulers with a flat bed or low-sided box. They are used for hauling supplies and equipment from one point to another. Some occasionally are used for towing and may pull one or more trailers. Fig. 2 shows a typical utility truck. SPECIAL-APPLICATION VEHICLES Special-application vehicles are possibly the most important of all support types since these vehicles di¬rectly support and maintain production equipment. Such vehicles are available in a wide variety of sizes, mechanical functions, and operating specifications. Most versions are four-wheel drive and articulated. Among the more common vehicles are explosive haulers and loaders, mechanic's trucks, lubrication trucks (Fig. 3), and special carriers. TYPICAL APPLICATIONS Development Utility haulers are essential in trackless operations to bring supplies to advancing headings. Some utility haulers may be dedicated to bringing in steel sets and may be equipped with boom lifts to unload heavy sup¬ports or even place them as required. A rockbolt hauler may have a boom-mounted operator's basket which can be used for bolt installation or inspection. Various mechanic's trucks and pipe trucks service the heading to keep power, air, water, and ventilation at the face and to keep face equipment at maximum utilization. Production Production operations require a variety of support equipment. Because of the larger crew size brought about by the addition of the production force, personnel carriers play a greater role. Correspondingly, steel¬support hauling equipment and bolting trucks usually see limited application. PRODUCTION UNITS Capacity Personnel carriers are available to carry almost any number of people desired. Likewise, other types of carriers or haulers can and are built to fit specific re¬quirements. Physical size, capacity, and operating char¬acteristics can be varied to fit any size of opening and operating condition. Generally, articulated models offer greater maneuverability than straight frame-axle steer designs. Most vehicles of this type are lower in power than production units, generally under 74.6 kW (100 hp). Operating performance still compares favorably to that of production equipment, i.e., the support vehicles can travel at equivalent speeds on the various mine gradients. Manpower Auxiliary vehicles should require only a single opera¬tor. Specific application vehicles may require more than one person. For example, ventilation trucks usually require a crew of two where pipe must be installed.

Jan 1, 1982

By L. K. Marshall

Last month's engineering fundamentals article discussed some general considerations of underground mine ventilation. This month's article takes a look at auxiliary ventilation-brattice, fans, and ducting-in underground mines. The need for good, efficient auxiliary ventilation increases as mines get deeper and move farther from ventilation shafts. New mining methods and equipment resulted in faster work area advances, liberating more dust, gas, and heat. As a result, worker health and safety requirements in the face area have become more stringent. For all these reasons the safety and efficiency of any underground mine depends heavily on its auxiliary ventilation. The purpose of such ventilation is to supply sufficient quantities of clean air to the face of the drift and to maintain air quality within desired limits until expelled from the mine.

Jan 2, 1982

By George H. K. Schenck

It seems appropriate to review the history of mechanization of our underground coal mines at this time when many favorable flags are flying for this industry. It is a reasonable hope that such a review may stimulate thinking as to the directions that new technological developments are apt to take and in which members of the Society of Mining Engineers are destined to play important roles. Discussion of the relative importance of the various changes that have taken place since the advent of electric power provides the starting point. It is in the economic factors utilized that we find conditions which permit more efficient utilization of the capital committed to the industry. Concepts rather than specific items are emphasized in the following discussion because once the value of a concept, such as mechanical conveyors, is established, it then spawns many variations which are not significantly different. The shift from animate to inanimate energy has been the most important change in the modern industrial scene, including coal mining. Although introduced into coal mines for some purposes early in the period of general electrification, the coal industry adopted mechanical power relatively slowly, and 1944 was the first year in which a majority of deep-mined coal was mechanically loaded.

Jan 1, 1968

By B. Elevli, M. D. G. Salamon

Production scheduling of an open-pit mine is one of the most important steps in open-pit mining. The mine's production schedule defines the distribution of cash flows and, as a result, directly influences the net present value (NPV) and overall economic feasibility of a project. The need to plan and operate a mine with an optimum production schedule has been obvious for some time, but the methods used to obtain such a schedule have not been so obvious. The current practice is to do a trial and error analysis by hand. In an attempt to improve the way production scheduling is currently done, a new computer based production scheduling algorithm was developed. This paper describes the fundamentals of this newly developed heuristic scheduling algorithm and its application to a gold deposit. The results of this case study show that the schedules, based on the new method, provide improved cash flows compared to production schedules done manually.

Jan 1, 1992

By S. W. Mao

Hydrologic and economic criteria figure in many obvious ways in water resources development, but they are rarely linked quantitatively, and most of the applications are pertinent only to the case-in-point. In the preparation of the Regional Plan for the massive program of ground water development in the Punjab, situations have arisen where the choice among two or more alternatives was made by analyzing the economic implications of critical hydrologic parameters. Two of these situations which are of more-or-less general interest are described herein. The first involves basic development policy -- whether ground water development should be based on the demand of the economy, or the conservation concept of safe-yield. The analysis demonstrated that mining of ground water is clearly indicated for areas where alternative supplies are unavailable. The second problem involves integrating hydrologic data into an economic model to determine optimum well design, From an analysis of all pertinent factors, a simple nomograph was derived which can be used to determine well specifications on-site during construction. The nomograph can be modified for use in any alluvial terrain.

Jan 1, 1967

By Dermot M. Ross-Brown

The objectives of this generic study were to use numerical modeling techniques to determine under what conditions seismic waves generated by an earthquake might cause instability to an underground opening, or cause fracturing and joint movement that would lead to an increase in the permeability of the rock mass. In general, the study showed that moderate earthquakes (up to 0.41 g) did not cause instability of the tunnel or major fracturing of the rock mass. An artificial rock-burst tremor with high accelerations, however, was found to be amplified around the tunnel, and fracturing occurred as a result of the seismic loading in salt and granite. In shale, even moderate seismic loading resulted in tunnel collapse.

Jan 1, 1981

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

GENERAL STATEMENT The primary objectives of any field data gath¬ering effort should be to (1) identify and gather the data necessary for the project and (2) obtain the data in a state-of-the-art manner. All too often the initial field data are collected both areally and tem¬porally in an illogical manner without the guidance of a conceptual model of the ground water flow systems involved or even a review of existing geo¬logic literature on the area of interest. The initial data collected frequently are of limited value while necessary basic reconnaissance information is miss¬ing. Initial field data should be collected with the intent of developing a hydrologic overview of the potential mine site and surrounding area. Ob¬viously, one of the initial objectives is to define the area requiring a hydrologic investigation. The data requirements should be identified by the time frame in which collection should be made and by the corresponding increase in sophistication of the data requirements with development and operation of the mine. The data requirements are summarized in Table 1. INITIAL LEVEL SITE INVESTIGATION Area Determination The initial task of any hydrogeologic investi¬gation is to determine the boundaries of the area requiring study. Obviously, the site of the proposed mine is included in the study area. The areal extent beyond the site may be determined from an eval¬uation of existing geologic and topographic maps. Those formations that overlie the ore body, the formations containing the ore body, and the formation(s) that lies immediately beneath the ore body are of direct concern for proper site recon¬naissance. Additional formations below the ore body may require study depending upon their thick¬ness, hydraulic conductivity, and degree of inter¬connection with the mine workings. This initial viewpoint identifies hydrostratigraphic units based strictly on geologic concepts such as mineralogy and structure. Formation outcrops, synclines, an¬ticlines, faults, and fracture and joint patterns are used to delineate the area of the site reconnaissance. The simplistic hydrogeologic environment (il¬lustrated in Fig. 3, chapter 2) requires that field data be collected via test wells and/or geophysical techniques. This approach is necessitated by the lack of surface features such as formation outcrops, streams, and springs. Fig. 5 (chapter 2) illustrates a slightly more complex hydrogeologic regime. The potential mine sites at locations A, B, C, D, and E each intercept a different ground water flow sys¬tem or combination of flow systems. Therefore, each mine location requires that a different area and size of area be investigated. A more complex geologic setting as illustrated in Figs. 6 and 7 (chapter 2) may be approached differently. The area included for the site recon¬naissance should encompass sufficient surrounding area to include the outcrops of those formations suspected of being influenced by the future mine. Even adjacent areas not suspected of being influ¬enced may be investigated if the formations of in¬terest crop out in those areas. Such an extension of the area of investigation would provide a greater regional understanding of the hydrogeologic properties of the formations (hydrostratigraphic units) of interest. Geologic Investigation The initial step before conducting the site re¬connaissance is to review all existing literature on the geology of the area. Existing information should be augmented with new exploration data on the dip, strike, thickness, and lateral extent of the for¬mations in the area. Exploration hole logs should be reviewed for indications of lost circulation, rub¬ble zones, and water producing zones. Existing aer¬ial photos such as those available from the US Department of the Interior, EROS Data Center,

Jan 1, 1986

By Carl E. Williams

Several years ago it was decided that ASARCO was in need of a good mine scheduling program to complete the computerized open pit mine planning package that was being used on new prospects and operating properties. A trial and error approach was being used to schedule a mine on a year by year basis, but this was time-consuming and far from offering an optimum solution l. Due to the magnitude of time and expertise required to develop such a sophisticated computer program, it was decided to search outside of the company for one already developed and available for purchase, This proved fruitless and therefore proposals were requested from consulting firms that had the expertise to develop such a program. Out of the five firms that submitted proposals, the one chosen was Systems Control, Inc., (S.C.I.) of Palo Alto, California. S.C.I. was selected because it was felt that they offered the greatest capability in the mathematical solution of complex problems. But due to their lack of mining expertise, a cooperative venture was developed whereby ASARCO would supply this mining knowledge. The selection of this vendor, the formulation of the contract and specifications, and the development of the computer program required about 3 years to accomplish.

Jan 1, 1973

By R. J. Pindred

Discussion by R.J. Pindred In his paper, Davis presents an overview of risk. He also introduces the Capital Asset Processing Model (CAPM) as a foundation for selecting the appropriate discount rate for a mining project. While applying portfolio theory is more defensible than the ad hoc adjustment of discount rates, the CAPM is not a panacea. CAPM shortcomings [The CAPM, as Davis stated, is expressed in the equation: ri=rf+pi4) where ri is the project discount rate rf is the risk free interest rate (3i is the project beta, and 0 is the market risk premium (rm - rf)] Application of the CAPM is more difficult than Davis indicates. Valuation is prospective, while the CAPM parameters are historical. Beta is determined from a regression analysis of historical data, while the beta needed for valuation is the expected beta. Betas are known to be unstable and the regressions that generate them often have low explanatory power. The difficulty of estimating a "project" beta must also be considered. Thus, the beta that is used in the CAPM will be based on the analyst's judgment. Like Cavender's discount rate, this judgment can lead to different project NPVs. Subjectivity in valuation cannot be avoided by a mechanical application of the CAPM. The risk-free rate, which Davis identifies as a short-term real rate of 4%, is also subject to scrutiny. A mining project is not a short-term investment and no single risk-free rate is appropriate for all of the cash flows. The hypothetical mine discussed in Cavender's paper is a six-year project. One might argue for the application of a risk-free rate from the Treasury yield curve at the duration of the project (in a bond-duration sense). This, too, is inappropriate. The risk-free rate should be matched to the timing of the cash flow. These rates can be determined by calculating the implied forward rates from the yield curve using a procedure known as "bootstrapping." It is likely that each of the project's cash flows would be discounted at a different rate. Commodity prices Davis criticizes the "ad hoc adjustment to the discount rate." Yet, in his discussion of the value of stochastic simulation, he suggests that the gold price be modeled as a "random walk, with or without a trend." This is essentially an arbitrary modeling of price risk. Consider that a liquid market in gold futures exists. The futures' price curve, which is closely related to the market's estimate of future spot gold prices, should be used to provide inputs to the model. This is especially true of a relatively short six-year project. Alternatively, as Davis correctly points out, a risk-averse investor can sell the commodity short to hedge price risk. Is it any more correct, in the portfolio sense, to account for price risk at all ?? References Cavender, B., 1992, "Determination of the optimum lifetime of a mining project using discounted cash flow and option pricing techniques," Mining Engineering, Vol. 44, No. 10, pp.1262-1268 Fabozzi, F.J., 1993, Bond Markets, Analysis and Strategies, Second Edition, Prentice Hall, Inc. Higgins, R.C., 1992, Analysis for Financial Management, Third Edition, Richard D. Irwin, Inc. Solnik, B., 1991, International Investments, Second Edition, Addison Wesley Reply by G.A. Davis Pindred discusses two issues related to my paper, the shortcomings of the Capital Asset Pricing Model (CAPM) and which commodity price values to use in the valuation exercise. Even though these topics are not directly related to the use or misuse of Monte Carlo simulation, they are important points to take into consideration in valuation exercises. Since I do not appear to have addressed these issues satisfactorily in my original paper, I will comment on each here. Pindred agrees with me that applying portfolio theory, and specifically the CAPM, to the selection of project discount rates is more defensible than ad hoc methods. But he then points out that the application of the CAPM to project valuation is more difficult that I indicate. It is true that the CAPM is a difficult tool for project valuation in general,. But the application of the CAPM to mining projects is one of the easiest I can think of. The biggest problem with using the CAPM for project valuation is coming up with an expected project beta. I suggest a project beta for gold projects of 0.45. The "true" value might be 0.35, 0.55 or whatever. Pindred correctly notes that the selection of the appropriate project beta is based

Jan 1, 1996

By Nellie E. Guernsey, Louis J. Sousa, Alfred Weiss, Nickolas J. Themelis

Over the past decade, numerous factors have led US copper firms to face increasingly severe competition from low cost foreign producers. As a result, greater attention is being devoted to developing and implementing new technology that can reduce costs and maintain the competitive position of domestic firms while simultaneously meeting environmental requirements. To obtain a better understanding of the likelihood of the development, adoption, and use of innovative copper technologies in the future, the Bureau of Mines contracted with Mineral Systems Inc. of Stamford, CT, to undertake a systematic survey of technological experts in industry, government, and the academic community. According to the survey, major developments in exploration over the next 25 years are likely to be in technologies that facilitate analysis and interpretation of deposit data rather than those that enable the collection of additional data. Most new copper mining and beneficiation technologies are likely to represent evolutionary extensions of existing systems with a notable increase expected in the application of information systems technologies and computer control methods. A possible movement towards increased usage of continuous mining systems in copper was also noted. Experts indicated that several copper smelters are under consideration for extensive renovation and, as a result, flash smelting technology is expected to become much more widely used in the US. A gradual movement toward continuous smelting methods was also forecast. In copper refining, the major technological change expected is the gradual automation of various refinery operations. Finally, though increased usage is expected, in situ solution mining and hydrometallurgical processing of sulfide ores are not expected to become widespread over the forecast time horizon. This first article in a two-part series describes the survey method chosen and the technological innovations selected for eval¬uation. Also discussed are the assessment panels, background scenarios, critical events, and diffusion forecasts. Next month, part two will address technology forecasts resulting from the study. Featured are discussions on future copper exploration, mining, beneficiation, smelting, refining, and recycling. A cost/benefit analysis will also be included. Methodology Selection of Assessment Method To develop a consensus forecast of technological change in the copper industry, a technique for systematically polling subjective opinions of experts was required. After conducting a literature survey and some preliminary testing, the direct probability assessment method was selected. With this assessment method experts are asked to express in quantitative terms their judgment of the probability that a specified event will occur, usually over a series of time frames. The method was chosen because the experts were observed to be more comfortable with this approach during the testing period, and the results of this process effectively satisfied the assessment objective. The experts generally could provide more precise estimates of the timing of future events using this technique because it was the least cumbersome of the assessment methods tested. Identification, Selection, and Description of the Technologies The initial list (Table 1) of innovative copper technologies assessed in the study was developed from two principal sources: knowledge and expertise of the study team and a review of relevant technical literature. From this list of 47 potential technologies, 10 were selected for detailed assessment. Table 2 lists 35 technologies that were subsequently identified in the first series of assessments. Twelve technologies from this list were also selected for detailed evaluation in a second assessment round. Criteria used for the final selection of technologies for detailed assessment specified that: • The expected impact of each technology on copper supply (i.e.,

Jan 9, 1983

By Paul H. Rylund

Substantial priming was a considered necessity for proper initiation of ammonium nitrate-fuel oil mixes as ANFO began to carve its niche in the mining industry in the latter fifties. Heavy priming accompanied the introduction of prills and oil to many blasting operations, large charges of high explosives were commonly used at the bottom, top and frequent intervals through-out the column. As the quality of ammonium nitrate improved and operators became more experienced, primer costs began to diminish. Increased experimentation continued with reduced primer costs a main objective. Cast primers were introduced and became accepted as an excellent companion for ANFO. Although the trend toward larger diameter boreholes became increasingly popular, emphasis on lower and lower priming costs continued. A primer was simply required to produce any type of initiation within the ANFO column to be considered adequate. Suddenly ANFO priming had digressed from excessive to marginal. Early experimental data developed at "test site" and laboratory locations indicated that ANFO had a tendency to react inefficiently in the initiation region of the column unless substantially primed. This was evidenced by the presence of unstable reaction rates detected with newly developed detonation velocity measuring equipment. These 10" order or "transient" velocities were believed to originate because of inadequate primer strength or a primer diameter to column diameter mismatch. How-

Jan 1, 1972

By X. M. Yuan

In the flotation of Zn-Pb ores, sphalerite is floated following copper sulfide activation. In this type of sulfide ore, pyrite is commonly treated as a gangue, and poor selectivity between sphalerite and pyrite/quartz is often reported. But pyrite may also appear in association with gold, and flotation of such auriferous sulfides is of great importance in many countries (e.g. South Africa, Australia). In the cationic flotation of sulfide ores with dodecyl amine, sphalerite can be floated while depressing quartz and pyrite. While in a well-aerated pulp in the presence of lime (especially after oxidation with H2O2) the cationic flotation of pyrite is depressed, oxidation of pyrite in the presence of Na2S makes it floatable with amines even in very alkaline environment.

Jan 1, 2002

By T. Leftwich, G. Faison, K. Pavlich, R. Borden, S. Pavlou

Recent regulatory and policy initiatives under the Resource Conservation and Recovery Act (RCRA), and the Comprehensive Environmental Response Compensation and Liability Act (CERCLA), will have a significant effect in risk reduction requirements for the mining and minerals processing industry. For example, Congress is considering regulating 20 special wastes from the processing of ore and minerals through RCRA Subtitle D and TSCA. The performance of risk analyses and environmental planning at mining projects is often driven by Federal and state regulatory standards. Recent regulatory and policy initiatives by the Environmental Protection Agency under the Resource Conservation and Recovery Act (RCRA), and the Comprehensive Environmental Response Compensation and Liability Act (CERCLA), will have a significant effect on environmental planning and risk reduction programs for mining and minerals processing. Regulatory programs implemented under other Federal laws including the Safe Drinking Water Act, Clean Water Act, and Clean Air Act will also impact industry practices. This paper provides: 1) a brief overview of mining waste and mining waste management, and 2) a description of these regulatory initiatives and a discussion on the impacts of new requirements on environmental and risk reduction programs in the mining industry.

Jan 1, 1992

By D. L. Purcell, B. T. McClure, J. McDonald

The U.S. Bureau of Mines has completed a laboratory evaluation of exhaust emissions from a diesel engine using an oxygenated diesel fuel. The fuels tested were soy methyl esters in a neat (100%) form and low sulfur, petroleum number 2 diesel fuel (D2). The engine tested was a Caterpillar 3304, indirect injection, naturally aspirated, 75 kW, diesel engine that is typical of engines used in underground mining applications. The objective was to determine the extent to which oxygenated fuels, such as methyl esters, reduce diesel particulate matter (DPM), and their influence on upon gaseous emissions such as total hydrocarbons, CO, NOx, NO2, formaldehyde, and other exhaust emissions. Heavy- and light-duty transient tests were used to simulate load cycles typical of mine applications. The soy methyl ester fuel produced greater amounts of volatile DPM (organic material) but much less nonvolatile DPM (carbon soot) for overall DPM reductions. A diesel oxidation catalyst (DOC) typical of the type commonly used in metal and nonmetal mines was tested with both fuels. The DOC further reduced the volatile and total DPM when used with the soy methyl esters, but increased the total DPM for D2 due to sulfate formation. The soy methyl ester fuel reduced CO and hydrocarbon, and NOx emissions. The DOC further reduced CO and hydrocarbon emissions.

Jan 1, 1995