Search Documents

By G. Davis

It is well known that anticipated mineral prices can have an overwhelming effect on a property's expected value. However, price movements throughout the life of a project also affect value. Thus, it is necessary to not only estimate the expected commodity price at the start of a project but also the manner in which that price is likely to fluctuate throughout the project's life. This paper provides a simple method of incorporating mineral price movements into mineral project valuations.

Jan 1, 1997

By D. S. McAllister, P. M. Rice, M. E. Fowler

The Westside Light Rail Project, a major 19.3-km (12-mile) extension of Portland, Oregon's light rail system, includes 4.6 km (2.8 miles) of twin 5.8-m (19-ft) diameter running tunnels, a binocular type station which, at 80 m (260 ft) below the ground surface, will be the deepest mass transit station in North America, two 9.4-m (31-ft) diameter station access shafts, and a 5.2-m (17¬ft) diameter ventilation shaft. The tunnels are being excavated by TBM and conventional rock, soft ground, and mixed-face methods. Geologic conditions, alignment, underground opening design, excavation method selection, and payment provisions for excavation and initial ground support are discussed.

Jan 1, 1995

By Patrick G. Hill

This paper discusses safety protocols for Kiewit Construction’s Level (3) project. The Level (3) project will cover a majority of the United States, and literally thousands of site operations will be conducted over a wide geographic area under challenging conditions; rivers, roads and other features, both from the surface and often for great and from boring pits. Developing a progressive safety plan for fast-track linear projects using micro-trenching and directional boring techniques requires significant investigation, planning and evaluation. Safety protocols for inner duct installation, to be accomplished with extensive use of directional boring is an essential part of the safety plan for network construction. In light of the shear volume of work and the geographical extent of this project, in many different types of terrain, this paper will identify approaches to safety applicable to fast-track linear projects, whether surface or underground-based. Establishing a safety culture into all aspects of this operation will improve productivity and cut unnecessary expenses. This new approach involves continual improvement and evaluation of hazard analyses, inspection procedures and training.

Jan 1, 1999

By E. A. Martell, K. S. Sweder

INTRODUCTION Lung cancer in uranium miners has been attributed to alpha irradiation of basal cells of the bronchial epithelium by radon daughters, primarily by 7.7 MeV alphas from polonium-214 (Altshuler et al., 1964). It also has been was observed that for a given cumulative radon progeny exposure, uranium miners who smoke cigarettes have an incidence of lung cancer about 10 times higher than nonsmoking miners (Lundin et al., 1969). It has been pointed out that the large excess of lung cancer deaths among smoking uranium miners is a multiplicative effect (Doll, 1971), which suggested possible synergistic interactions between airborne radon progeny and cigarette smoking. Experimental studies of the complex pattern of interactions between radon progeny, cigarette smoke particles, and the cigarette smoking process are in progress in our laboratory. Preliminary results, reported elsewhere (Martell, 1981), implicate alpha radiation from indoor radon progeny in the etiology of lung cancer in all cigarette smokers. Cigarette smoking produces high concentrations of smoke particles of low mobility and respirable size--particles between 0.5 and 4.0 µm in aerodynamic diameter (see below). The attached fraction of indoor radon progeny is highly dependent on the air concentration of small particles from cigarette smoking and from other combustion sources (Martell, 1981). The size distribution and other properties of radon progeny associated with cigarette smoke particles enhances their effectiveness in the induction of bronchial cancer in man. In this paper we discuss the properties of radon progeny associated with cigarette smoke, the fractionation of radon progeny and modification of their aerosol properties in burning cigarettes, the role of 218Po in these processes, the production of insoluble 214Pb and 212 Pb enriched particles in burning cigarettes, and the consequent differences in the patterns of polonium isotope alpha irradiation in the bronchial epithelium of smokers. EXPERIMENTAL PROCEDURES Experimental methods used in these studies involve the use of small experimental chambers of known radon and radon progeny concentrations in combination with aerosol collection and sizing techniques and sensitive radioactivity detection methods. The use of low-level [ß-] counting for radon progeny determination, providing a measure of 214 Pb plus 214Bi activity, makes it possible to carry out chamber experiments with small radon emanation sources and relatively low air concentrations of radon and radon progeny concentrations in the range from 100 to 1,000 pCi per liter. Thus, for example, in a typical experiment we use a 10 nanocurie 226Ra solution standard in a 10 liter chamber, providing an equilibrium concentration of 1,000 pCi of radon per liter. In small sealed chambers, radon progeny plate out rapidly on the chamber walls, with steady-state concentrations of airborne progeny less than 2 percent of equilibrium levels. This is experimentally convenient because, upon introduction of high concentrations of cigarette smoke particles or small particles from other sources, there is a systematic ingrowth of attached radon progeny, providing a tagged aerosol source of known age and radon progeny composition. In some chamber experiments a 226Ra solution standard of small volume, acidified to O.1N HNO3, was used as the radon emanation source. When used with a bubbler the holdup of radon in an 8 ml volume of 226Ra solution standard at 0.1N HN03 was only 2% of the total radon in the chamber at equilibrium. For experiments with 212Pb-tagged aerosols, we used a dry Ba(228Th) stearate emanation source prepared by the method of Hursh and Lovaas (1967). 226Ra and 222Rn determinations were made by radon gas counting. The 222Rn in a sealed air or water sample is transferred, using helium gas as a carrier, successively through a dry ice cooled trap at -80°C to remove water, through ascarite to remove C02, and through a small activated charcoal trap at -80°C to collect the 222Rn. Subsequently, by heating the charcoal to 400°C, the 222Rn is transferred next to an LN2-cooled capillary trap, and finally into an alphascintillation counting cell of the type described by Lucas (1957). As already stated, radon progeny activities were determined by low-level [ß-] counting, which provides a measure of 214Pb plus 214Bi. The radon progeny samples, collected on efficient Delbag polystyrene micro-fiber filters or on impactor foils, are placed in close, sandwich geometry between two thin-walled flow counters inside shielding anticoincidence counters and a 15 cm thickness of steel shielding. This configuration provides nearly 4II geometry and a low background of only 0.25 to 0.30 cpm. Aluminum absorber was added to provide a combined thickness of absorber and counter wall exceeding 7.0 mg/cm2 to eliminate the variable contribution of 7.7 MeV alphas from 214Po. 212 Pb determinations also were carried out by low-level [ß-] counting, in this case using a combined absorber and counter wall thickness of 9.0 mg/cm2 to eliminate contribution of 8.8 MeV alphas of 21 Po. In each experiment the [ß- ]activity data were corrected for decay to an appropriate common reference time for assessment of activity distributions.

Jan 1, 1981

By Christopher Haycocks

The growth of computer and ground control technology in recent years, combined with an urgent demand for low-cost fossil fuels and mineral resources, has set the stage for full-scale utilization of computers in mine planning. Steeply rising production costs and the need to preserve the environment are placing great demands on engineers to improve their mining efficiencies, which can best be accomplished by applying the full capabilities of the computer. Pressure to develop and perfect programs with an immediate potential for improving mine de- sign, reducing mining costs and extending the viable coal reserves of the country has already come to bear in the form of exploding energy requirements, environ- mental considerations and the visible limitations of other energy sources. The computer program discussed in this paper, RAMPLAN (Rock Mechanics Applied to Nine Planning), was constructed as part of a continuing effort at Virginia Polytechnic Institute & State University under the sponsorship of the Office of Coal Research to develop a suite of programs to benefit the mining engineer in improving mine design and evaluation techniques. This program averages out structural data values obtained from randomly placed or gridded point sources across a mining property and uses these values in structural design equations. The basic purpose of the program is to provide accurate estimates of mineable tonnages, based on a realistic assessment of structural conditions existing in the deposit, for use in subsequent evaluation programs. Program output, however, also provides sound engineering data for the mine planner to use in planning and laying out new properties. Mining dimensions produced by the program provide a good starting point for initial layouts; and as more refined procedures are developed for increasing and improving the quality and quantity of information from boreholes, this information may be used with increasing confidence. The rock mechanics principles utilized in the program are generally well-established with full details provided to the user. To produce meaningful results extensive input data, obtained from exploration borehole core data, outcrop sampling points, or mine samples, are required. To assist the engineer, details of the types of tests that should be conducted have been listed. By including all of the ground control equations in the program the otherwise long and tedious calculations can be performed easily and quickly, and the work can provide the basis for a more detailed ground control study. The program is written in Fortran IV Level G to run on an IBM 3701155 ASP and requires 156K storage.

Jan 1, 1973

By G. Duncan, K. Winther, R. Ericsson

Distinct trends in grinding mill technology have emerged in recent years. In an effort to optimize overall mill performance for the needs of the End User, broad measures of logistical speed, process flexibility, operational risk, and overall costs now exert greater influence on the specification of grinding equipment. As a result, innovative alternatives to conventional grinding mill structures, supports, drives, feed, and discharge configurations are now being offered and selected with greater frequency. This paper investigates these trends in grinding mill technology, utilizing optimization and decision-theory techniques. In particular, the paper considers how specific advances in process design, product engineering, manufacturing techniques, and mining operations continue to relax technological constraints, enabling further mill innovation. In this context, a methodology is presented, illustrating how proper selection and specification of grinding mill components and configuration can target an optimization of the four End-User performance measures listed above.

Jan 1, 1999

By T. M. Storer

Much has been written and many discussions held on the virtues (and evils?) of a Company-owned motor fleet. Almost invariably these dialogues take a generalized form and thereby lose something since the individual circumstances, geography and philosophy - particularly in diverse industries, is never quite the same. In considering the nature of my remarks today, I felt a departure from the general approach might be in order, and in lieu of that, will attempt to present a concise picture of how we in the Lehigh Portland Cement Company view this problem and the steps we have taken in our efforts to solve it. At the outset a word may be in order about the Lehigh Company itself, what we do, and the problems that confront us specifically as well as the cement industry at large. We are primarily a manufacturer of portland cement operating 10 plants with a total annual capacity of about 23,000,000 barrels. We market this material in 30 states, shipping both from the plants directly as well as through a system of 18 distribution terminals. About 150,000 truckloads of cement are shipped to customers each year.

Jan 1, 1969

By P. Zhang

The results of bench-scale testing of five flotation processes for the separation of dolomite from phosphate are discussed. Each process is compared in terms of phosphate recovery, MgO content of the concentrate and reagent consumption. Water quality was found to play a major role in the performance of these processes. The effect of water hardness, in addition to other parameters, are discussed.

Jan 1, 1997

By E. T. Tuzcu

Microscale information about single particle fracture can be incorporated into the macroscale model of the whole size reduction process in the mill. The ultrafast load cell (UFLC) device provides a substantial amount of information about fracture characteristics of a particle under impact loading. UFLC captures high-resolution compressive force signals during particle breakage. The measurement of the compressive force at the instant of fracture of the particle allows computation of a number of comminution-related particle properties, as well as the energy absorbed during fracture. In the current study, limestone particles 50 mm in size were fractured to obtain specific fracture energies. Then, based on the experimental data, two models were proposed to quantify the fracture process. The specific fracture energy distribution of the particles in the range of 6 to 50 mm was defined by the well-known Weibull distribution. The other model is a probabilistic fracture model. This model is a link between energy events occurring in a grinding mill and the breakage rates of particles. The impact energy spectra or energy events occurring in a grinding mill can be obtained with a discrete element method (DEM) simulation. One can model the breakage rates of the mill material by combining the energy spectra with the probabilistic fracture model. This novel approach for the modeling of breakage rates via DEM and UFLC is shown here.

Jan 1, 2011

By Thomas L. Hurst, Joseph M. Hans

INTRODUCTION The former Shiprock uranium mill site is located in the community of Shiprock, New Mexico on a bench overlooking the San Juan River (Figure 1). Both Shiprock and the mill site are located on the Navajo Indian Reservation. The millsite was built on a 230 acre tract leased by Kerr-McGee Oil Industries Inc., and was operated from 1954 to 1963. The Vanadium Corporation of America and its successor, the Foote Mineral Company, operated the mill from 1963 to 1968. During its entire operation, 1.5 million tons of uranium ore was milled producing 3711 tons of U308 concentrate. The concentrate was sold to the former U.S. Atomic Energy Commission. During milling, the ore was crushed to less than 35 mesh and acid leached to remove the uranium. The [ ] uranium was removed from the leach solution by solvent extraction and the uranium-barren solution discharged into raffinate ponds for disposal by evaporation and seepage. The spent solids (tailings) were pulped with waste process fluids and water and discharged to form tailings piles. The piles (ponds or dams) were formed with earth starter dikes. The dike walls were then raised using the separated sand fraction of the tailings. The slime fraction of the tailings were discharged into the diked impoundment. Since only a small fraction (0.25 percent) of the ore was U308 by weight, most of the ore bulk ended up as wastes. The wastes contain nearly all of the uranium decay chain radionuclides present in the ore except uranium. The mill was shut down and partially dismantled before the lease expired in 1973, and the remainder of the mill and wastes reverted back to the Navajo Tribe which was the lessor. Portions of the millsite were then occupied by the Navajo Engineering and Construction Authority (NECA), a Tribal enterprise. In order to provide skilled personnel to operate earth moving equipment, a heavy equipment operator's training school was also established on the mill site and was administered and operated by NECA. The U.S. Public Health Service (PHS) and the Environmental Protection Agency (EPA) staff conducted radiation surveys at four inactive uranium millsites on the Navajo Reservation in April 1974. During the survey of the Shiprock millsite, it was noted that the training activities were degrading its radiological condition. Both the PHS and EPA staff recommended that the training activities be directed towards the decontamination of the millsite area and interim stabilization of the tailings piles. Preparation for the decontami-nation work commenced in April 1974. In order to facilitate the decontamination activities, the mill site and its contaminated environs were divided into major areas labeled A through F (Figure 2). Areas A, B, and C are defined as "perimeter" areas and contained surface contamination ranging from 5 to 30 cm deep. Area D defined the mill yard and contained contamination ranging from 0.6 to 5.5 m deep. Area E contained several raffinate ponds which were removed to line up the northwest boundary of the tailings pile and to move the contaminants away from the vicinity of the occupied on-site buildings. The contaminants in Area E ranged from 0.05 to 5.5 m in depth. Area F encompassed the ore storage yard. Contaminants in this area ranged from 0.18 to 1.2 m deep. Washes, however, had contamination exceeding 7.6 m deep.

Jan 1, 1981

By V. R. Burkhart

Pennsylvania Power & Light Company is an investor-owned public utility which was incorporated under the laws of the Commonwealth of Pennsylvania on June 4, 1920, with general offices at 901 Hamilton Street, Allentown, Pennsylvania. At the present time PP&L is operating five coal-fired steam electric stations, two hydroelectric stations and one steam heat plant which is being converted from anthracite to oil fired. In addition, PP&L is a partner in both the Keystone and Conemaugh mine mouth bituminous coal-fired steam electric stations in Central Pennsylvania and also part owner of a company which operates another hydroelectric station. PP&L plants, other than the two mine mouth stations, are located in Central Eastern Pennsylvania. (Figure 1) The company derives about 99% of its operating revenues from supplying electric service, while the balance is from the one steam heat plant serving the city of Harrisburg. The entire service area covering 10,000 square miles in 29 counties, has a population of approximately 2,300,000 people. The area served is mostly suburban. It includes 109 communities each having a population in excess of 5,000 people. The largest cities served are Allentown, Bethlehem, Harrisburg, Hazleton, Lancaster, Scranton, Wilkes-Barre, and Williamsport which range from 50,000 - 120,000 in population. So you see our service area does not include any major cities. The area has industrial, commercial, residential, agricultural and recreational activities that are linked with the Eastern Megalopolis by an extensive interstate limited-access highway system and railroad networks. We consider this Central Eastern Pennsylvania area we serve as the "heart of the market" -- an area with great growth potential.

Jan 1, 1973

By Dennis A. Fenton

This paper presents some techniques and data required to design large ball mills. The advent of larger size mills leads to consideration of the gearless drive as a practical solution to utilize large horsepowwers. The particular shell structure under consideration is subjected to thermal as well as magnetic loads. The magnitude of the inertia, magnetic and shell temperature characteristics have a very significant effect on the design and performance of the hydrodynamic pivoted shoe bearing. Particularly since these bearings have lower frictional resistance properties than hydrostatic trunnion tee rings. The structure of the mill is designed for long life. Parameters involved with the fatigue life of the structure are discussed together with some of the more important aspects of the design.

Jan 1, 1975

By Y. C. Kim

Although the first published optimum pit limit design algorithm by Lerchs-Grossmann dates back to 1965, the majority of the open-pit mines in the U.S. has not as yet adopted such a rigorous optimization algorithm. Instead, the floating cone approach initially developed by Kennecott Copper in 1961 is still used today for various reasons. However, shortcomings with the floating cone algorithm, particularly for precious metal deposits with erratic mineral distributions, have provided a renewed interest in optimizing algorithms.

Jan 1, 1988

By Jozef F. Zurawski

River Des Peres Foul water Interceptor (Skinker–McCausland Tunnel) is a gravity sewer tunnel constructed to eliminate dry sewage overflows during high river stages and to improve the wastewater collection and treatment. The original 78-inch (2m)finished diameter Skinker-McCausland Tunnel started as a 21,500 feet (6.5km)interceptor with 13 work, drop and access shafts. The tunnel constructions included soft ground, mixed face and rock tunneling in karst formation with maximum overburden of 175 feet (53m). Due to the success of the project, the tunnel alignment was extended another13,361 feet (4.1 km) and 7 new structures by negotiating two additional segments with the contractor and the designers.

Jan 1, 2001

By Y. Wang, E. Forssberg, R. J. Pugh

The coagulation of dispersed ultrafine weakly-magnetic oxide mineral particles (e.g., natural hematite and chromite) in an external magnetic field can be described by interparticle forces. Essentially, coagulation occurs when the short-range London-van der Waals interactions and the long-range magnetic forces outweigh the stabilizing electrical double-layer repulsion. Using the classical colloid chemistry theory, the various components of the potential energy for different-sized particles at a series of ionic strengths and magnetic field intensities were calculated. The results of this theoretical analysis were then related to the results obtained from experimental studies in which the magnetic field-induced coagulation of the ultrafines of natural hematite and chromite in aqueous suspensions were investigated using a laboratory-scale electromagnetic solenoid. The experimental results relate the coagulation process (as determined by magneto-sedimentation analysis) to the particle size, the slurry pH and the external magnetic field. In the magnetic fields, the maximum coagulation occurred near the pH of zero-point-of-charge (pHzpc) of the minerals (where the electrostatic double layer repulsion was reduced to a minimum) enabling the particles to enter the "primary minimum" energy sink. On the other hand, in cases where the electrostatic repulsion was not suppressed, the long-range magnetic forces enabled coagulation to occur in the "secondary minimum." This caused the formation of chains that appeared to be relatively stable during sedimentation.

Jan 1, 1995

By D. E. Pollock

Recent NIOSH published information has shown an increase of rapidly progressive coal workers? pneumoconiosis (CWP) in the southern Appalachian coal region (SAR) of the U.S., despite the fact that compliance data indicates that most coal miners have been exposed to coal mine dust concentrations below the statutory limit of 2.0 mg/m³. While the exact cause of these elevated CWP levels in the SAR has not been established, several factors may be contributing to the increase in occupational lung disease among coal miners. The mining of high rank coal is known to lead to higher CWP rates, and this type of coal is mined in a portion of this region. Also, a high percentage of the mines in the region are on reduced dust standards because of the high silica content of the airborne dust resulting in miners possibly being exposed to excessive amounts of respirable silica dust. Exposure to excessive amounts of respirable silica dust can lead to silicosis, a disabling and potentially fatal lung disease. NIOSH's Respiratory Hazards Control Branch has been investigating the possible causes that would account for the observed higher trends in disease progression through literature review, data analysis, and in-mine surveying. The investigation to date has revealed that underground mines are faced with cutting large amounts of rock in order to maintain haulage clearances. Cutting rock not only increases the potential for silica exposure, it increases the requirement for machine maintenance which was a concern observed during dust surveys conducted by NIOSH. Over half of the mines operating in the SAR are on reduced standards due to high silica content. Adequate face ventilation of the continuous miner and roof bolter and limited down-wind operations from the miner are also issues of concern and items which require the constant attention of miners operating in these conditions. Disclaimer: Mention of any company or product does not constitute endorsement by the National Institute for Occupational Safety and Health.

Jan 1, 2009

By Georgene Renner, William R. Yernberg, Steve Kral

ABB provides integrated pro-cess control, optimization and information systems, drives and power-distribution equipment as well as other services and support to the mining industry. ABB also supplies electrical equipment and control systems for the openpit mining industry. This includes products for the automation of electrical equipment in mine shovels. The company offers low- and medium-voltage drives for various mineral- industry applications. And ABB provides gearless mill drives for equipment, such as semiautogenous grinding mills that are too large for conventional drives. ABB Industrial IT provides innovative hardware and software systems that cover all the requirements of the modern mining and processing plant.

Jan 1, 2004

By Raja V. Ramani

As the new millennium approaches, it is appropriate to assess the progress that has been made in mine health and safety, a matter of concern to management, labor and government. One can hardly look at the major events of the last century — from the birth of the US Bureau of Mines through the enactment of the modern health and safety laws — without realizing that the march has been relentless toward eradication of health and safety threats in mining. The progress is spectacular in mine safety and significant in mine health. In looking at the future, it is safe to assume that societal demands will increase for improved health and safety conditions in the workplace. So will the demands for greater technological leaps. The standards will for measuring success and the expectations of progress in creating a safer and healthier mine environment will grow. The possibilities are enormous of meeting these exacting requirements in the 21st century.

Jan 1, 1999

By N. Mehrshad

Research and experience have demonstrated that the operating conditions of the flotation process are reflected in the froth?s appearance. Despite recent advances in image analysis and several algorithms developed for froth flotation, there still is not a comprehensive algorithm to accurately determine bubble features from actual froth images. Being able to accurately and automatically measure bubble size distribution is an important requirement for optimization and control of the flotation process. Segmentation is one of the most effective approaches for accurately determining the bubble size distribution. In the present study, a new bubble segmentation algorithm, which utilizes an adaptive marker-based watershed transform, is proposed to measure the bubble size distribution from froth images. The developed algorithm is validated using some industrial scale froth images from flotation cells at different duties.

Jan 1, 2011

By Jeffrey B. Smith

Introduction The gas shortage is going to be with us for some time to come. If we can set aside political and industry rhetoric (along with subjective personal opinions), we still are confronted by two serious "facts of life": (1) for almost a decade the U.S. has been con¬suming natural gas at a greater rate than we have been finding new reserves; and (2) there is a finite amount of natural gas present within the earth&apos;s crust. Much of the known and easily exploitable sources of gas (the so-called "conventional" sources, such as the high permeability sand reservoirs of the Tertiary sequence along the Gulf Coast) already have been developed; their production is declining rapidly. The total producible reserves from con¬ventional gas reservoirs amount to only 216 Tcf, less than an 11-year supply. However, several large potential resources of natural gas remain to be developed. These "uncon¬ventional sources" have low permeability and/or peculiar producing characteristics. The DOE program for development of these unconventional sources of gas is called the enhanced gas recovery (EGR) program. The primary goal of this program is to provide a data base of resource characterization and production technology that will lead to commercial development. DOE will encourage and support in¬dustry participation in developing and demonstrating technologies needed to reach this goal. Unconventional Resources Four major unconventional resources of gas have a high potential for commercial development. There are other unconventional sources (such as gas hydrates) that are too poorly defined to warrant a major development thrust at this time. The four unconventional sources of gas currently included in the EGR program are: 1. The carbonaceous shales of Devonian age in the Appalachian, Illinois, and Michigan sedimentary basins are the targets of the Eastern Gas Shales Project (EGSP). 2. The low permeability, low porosity so-called "tight" gas sandstones of the Upper Cretaceous/Lower Tertiary in the Rocky Mountain areas constitute the resource target for the Western Gas Sands Project (WGSP). 3. The free methane trapped in coal beds of both the eastern and western U. S. constitute the Methane from Coal Beds Project (MCBP). 4. The abnormally high pressured, high-temperature saltwater aquifers of the Texas¬Louisiana gulf coast are targets of the Geopressured Aquifer Project (GPAP). Basic implementation strategy for these EGR projects involve (1) assessing and characterizing the resource potential of the resource; (2) conducting cost-shared field testing with industry to improve, develop, and demonstrate various stimulation and production technologies; (3) coordinating EGR activities within DOE and with other federal agencies (such as the Bureau of Mines) to minimize duplication; and (4) aiming all projects toward commercial development of the gas resources. EGSP What type of "geological animal" is the EGSP dealing with? While gas undeniably is related to the occurrence of natural fracture systems within the shale, the overall producing mechanism and precise location of fractured, gas¬bearing locales within each basin is still poorly understood. By developing reliable resource characterization techniques and applying effective stimulation technologies we intend to elevate the Devonian shale from the status of a potential gas resource to that of a proven gas reserve. Once we have done this the private sector can take over the large-scale commercial development of the Devonian shale gas resource. WGSP The second largest project (both in terms of complexity and level of funding) is the WGSP. The primary targets for this project are the low permeability (< 1 md) gas sandstones of the Piceance, Uintah, and Greater Green River basins and the Northern Great Plains Province. Project success in these four primary geologic locales will permit investigating additional low permeability sandstones in 16 other sedimentary basins. It ap¬pears that the only practical means of increasing permeability and resultant flow rates from these sandstones lies in the use of massive hydraulic fracturing techniques. Unfortunately, it is still too early to design such jobs with predictable results. MCBP The MCBP is to be involved in producing and utilizing methane derived from coal beds. The coal, like portions of the Devonian shale, is impermeable, highly fractured (termed "cleat" by

Jan 1, 1980