Search Documents

By H. V. Alminas

The U.S. Virgin Islands consist of three major islands (St. Thomas, St. John, and St. Croix) and some 50 smaller islands that are located primarily along the coasts of St. Thomas and St. John. St. Croix, the largest of the islands, is located approximately 160 km south-southeast of San Juan, Puerto Rico and is about 218 km in area (Fig. 1). St. Thomas, the second largest island is located 64 km east of Puerto Rico and incorporates approximately 77 km2. St. John is located immediately to the east of St. Thomas and incorporates approximately 49 km2. The climate in the U.S. Virgin Islands is maritime tropical. The average annual rainfall at higher elevations is 127-152 cm and at lower elevations 51-76 cm. There is no well-defined wet or dry season. Temperatures generally average in the 80's (F°) with only a 5°-7° F variation throughout the year.

Jan 1, 1987

By J. Perlacia, J. M. Eguiluz

"INTRODUCTION The Bulk Handling Technology has suffered an important development in the recent years, allowing the use of conveyor belts in the most important and critical applications. As a consequence of this, the reliability and lasting performance of the conveyor belt components is becoming more and more significant, thus the implementation of preventive maintenance programs is a must. The rollers are one of the consumables in the conveyor belts, which have to be changed once arrived to the end of life. The actual ways of detecting this moment always require intensive use of labour and they are not very accurate. Indeed, if the rollers get broken before replacement, the consequences could be very important, generating additional costs and operational losses. The R&D Department of ULMA Conveyor Components, has been working since early 2012 on the development of Monitored Rollers along with a Management Software to provide users the capacity to Manage and Monitor the rollers from its desk, getting continuous online information on the internal temperature of the bearings, on the working status of the rollers as well as the identification of the rollers close to their end of life so that they could be changed during the next maintenance stop of the conveyor belt. In short, a system of Preventive Maintenance for Conveyor Belt Rollers BACKGROUND AND CURRENT STATE The malfunction of a single roller in certain conveyor belts can suppose the standstill of the whole installation until its replacement, due to the risk of greater and more expensive failures like the rip of the belt. In the case of a bulk handling installation where a continuous supply of material is necessary, a bare stop of one hour could entail huge economical losses. What’s more, many conveyor belts are several kilometers length or the access to some parts of them is very complicated. Due to these difficulties the inspection and maintenance operations can become expensive and hard going, with staff going over the whole area checking the correct condition of the conveyor and rollers, which means a dangerous activity. In addition, it’s quite common to find rollers working in very harsh conditions, completely exposed to the elements or working in corrosive closed environments like underground mines. These tough working conditions together with the very demanding features of Bulk Handling sector (high loads, speed, dangerous materials etc.) can bring the unexpected failure of a roller, even being designed to support them. Thus, to have the working conditions of the rollers real time is clearly required, in order to achieve an actual predictive maintenance of the system and avoid fatal failures. Nowadays the most common procedures to identify a broken roller is to hear how it sounds or use thermo-graphic cameras to measure their internal temperature, both of them implying workers inspecting the whole length of the conveyor while the conveyor is running. This means intense use of workmanship and operational safety level reduction."

Jan 1, 2018

By R. M. Reyes, D. Negrete, G. Herrera

First Majestic Silver Corp’s La Encantada Silver Mine is a producing mine with a capacity of 3,000 tonnes per day. The La Encantada team is currently constructing two small-scale caving mines, including the San Javier breccia caving mine. The new mine is constructed within a mineralized breccia body composed of clasts of varying sizes and with very poor rock quality. Due to this poor rock quality, primary and secondary supports are required to support both the development and production stages. Since the proximity of the new mining levels to existing old workings, correct selection of the support system and proper production controls, instrumentation, and monitoring are very critical to maintain the stability of the pillars and fortification elements. An increased ground deformation due to the load transfer during the production stage is expected. This report reviews the primary and secondary support elements used in the different stages of mining, the monitoring of ground deformation, and the steps taken to analyze and visualize the collected data in order to enable the geotechnical team to manage caving stress and maintain pillar stability. INTRODUCTION First Majestic Silver Corp. (“First Majestic”) is a Canadian mining company focused on silver production in Mexico that operates six producing silver mines, including La Encantada Silver Mine (“La Encantada”). First Majestic acquired La Encantada in 2006. La Encantada is located in the northwestern portion of the state of Coahuila, in northern Mexico, in the municipality of Villa de Ocampo. The mine lies in the northern part of the Sierra Madre Oriental physiographic province. The mine location is shown in Figure 1. La Encantada is a producing mine, with a mill processing capacity of 3,000 tpd, and a 4,000 tpd capacity cyanidation leaching circuit equipped to process fresh underground ore and old tailings amenable to be reprocessed. The mine is currently employing several mining methods, including overhand cut and fill for narrow veins, small mantos, and other minor deposits. A subset of caving methods are applied on the larger, but weak, mineral deposits, such as at the San Javier breccia and La Prieta breccia. La Encantada consists of vein, manto, breccia pipe, and chimney deposits with concentrations of silver, lead, iron, and zinc in oxidized mineralization enclosed by calcareous sedimentary formations of Cretaceous age. At deeper levels, there is sulphide mineralization in skarn with zinc and silver concentrations associated with a granodiorite intrusion.

Jan 1, 2019

By B. N. Conley, K. D. Luxbacher

"The underground coal mining industry in the United States has recently seen the occurrences of several high profile, multi-fatality events. The explosions that occurred at the Sago Mine in 2006, the Darby Mine in 2006, and the Upper Big Branch Mine in 2010 have caused a ripple in an otherwise steadily improving safety record. These events transpired in the midst of an unprecedented level of government regulations and modern safety technologies. The recent increase in fatal events in conjunction with a minimal decline of both fatal and non-fatal injuries over the past decade may signify that current safety practices have reached a level of diminishing returns. Risk management, a safety approach that has been successfully applied in various industries including mining across the world, may provide a means to surpass the safety plateau in the U.S. RISKGATE is an Australian risk management program for mines that shows great potential for application in the U.S. However, fundamental differences between the coal mining industries in Australia and in the U.S. prevent direct implementation. This paper discusses aspects of the RISKGATE body of knowledge that require some adaptation before this program may be applied to the U.S. mining industry. INTRODUCTION The underground coal mining industry in the United States has recently seen the occurrences of several high profile, multi-fatality events. These events transpired in the midst of an unprecedented level of government regulations and modern safety technologies. The recent increase in fatal events in conjunction with a minimal decline of both fatal and non-fatal injuries over the past decade may signify that current safety practices have reach a level of diminishing returns. In order to combat this stagnation in performance, a modification to the manner in which the mining industry approaches worker safety may be warranted. The implementation of a risk management based approach presents a potential method for not only surmounting the current safety plateau but also for achieving the long desired objective of zero harm. RISKGATE a risk management body of knowledge designed for the Australian mining industry that shows great potential for application in the U.S. This paper discusses aspects of the RISKGATE body of knowledge that require adaptation before implementation in the U.S. mining industry. These adaptations are based on differences in operating practices and governmental regulations. This discussion will focus on the three major U.S. risk areas of explosion prevention, ground control, and moving equipment."

Jan 1, 2015

By H. B. Trinh, R. R. Srivastava

"Spent auto-catalyst is a potential secondary resource because of the higher concentration of valuable platinum group metals (PGMs) as compared to the primary ores. Despite the well-developed commercially tenable technologies, further researches are being carried out to extract the PGMs with high efficiency. It is however, critical in this context to reuse not only the PGMs but also other metals contained in the spent auto-catalyst particularly that of the cordierite substrate such as aluminum, magnesium and cerium oxide (CeO2). This is important in view of the fact that no recycling process has ever stressed upon the recovery of cordierite substrate and CeO2 since the main target metals are mostly the PGMs. In this study, a new hydrometallurgical approach has been proposed in order to recover the PGMs as well as cerium oxide and materials from the cordierite substrate by using sodium hydroxide roasting followed by sulfuric acid dissolution. Under the optimal conditions for roasting at above 600°C, and weight ratio of sample to NaOH of 1:1 for 60 min, the cordierite was converted to the soluble phases. Dissolution of the roasting products using H2SO4 solution (1M) at 25°C for 60 min enriched the PGMs and Cerium oxide contents in the residue. Subsequently, PGMs in solution after dissolution can be cemented using Al and Cerium oxide in residue can be recovered by hot digestion using concentrated H2SO4.. INTRODUCTION Auto-catalyst can significantly control the gaseous emission of automobiles, and has been considered as a potential secondary source of Platinum group metals (PGMs) after being decommissioned from the vehicles. The PGMs demand is continuously increasing to comply with the growing vehicle population and the tightening of emission standards all over the world; meanwhile the natural resources of these metals is facing the threat of depletion. Therefore, it is crucial to progressively substitute with an alternate resource to supply PGMs other than that of the primary ores. Nowadays, vehicular transportations worldwide are totally installed with the auto-catalysts. However, they should be replaced after reaching their service life. If there is no recycling of such resources, huge amount of valuable metals will be wasted. The quantity of PGMs that can be recovered from the spent auto-catalyst depends on the size of car, which averages to 1-2 grams for small cars and 12-15 grams for the big truck; this is significantly higher than that of the primary ores containing 2-10 grams PGMs per ton. Consequently, the recovery of PGMs from spent auto-catalyst becomes extremely favorable as compared to the primary resources due to higher concentration of PGMs, with much lower and simpler processing steps, and lesser pollution."

Jan 1, 2018

By Heflin. L.

The Washington Metropolitan Area Transit Authority, WMATA, has constructed over 92 revenue miles of rapid transit facilities including some 14 miles of rock tunnel and 12 miles of earth tunnel. The system map is shown in Figure 1. During construction it is not unusual for contractor to encounter ground conditions resulting in major problems and extra cost. Problems such as major rockfalls and a "stuck" boring machine in squeezing rock are not unusual. In recent years, faced with additional tunnel construction projects, the Authority has sought newer tunneling methods which might be less costly. One new method which has been tried is NATM, the New Austrian Tunnel¬ing Method. NATM, which is applicable to both soft ground, mixed face and rock tunneling, relies on miners and comparatively small machines to excavate in conventional ways, but it is unique in its methods of obtaining "stand-up" time at the excavated face and its method of using shotcrete as an initial lining, frequently with a drainage system to reduce hydro-static pressure on the final lining. Lower costs result from use of a cast-in-place concrete liner, and from a reduction in the number of work operations at the mine heading which provides better daily production. WMATA has recently completed three twin bore tunnels constructed by NATM technology. The first was the Wheaton Tunnel and Section, followed by the tail track tunnel to total some 4200 linear feet cut through jointed rock up to 270 feet below ground surface, and the last was in soft ground at Fort Totten. A

Jan 1, 1993

By J. Mark Richardson, Mary S. Sredanovic

The use of computerized steady-state process design balance systems has reduced engineering man-hours by as much as 80 to 1 over conventional manual balance calculations. The popularity and widespread use of such systems by the minerals industry increased dramatically in recent years, but these systems were mainly available for use on large main frame computers and lacked graphic capability. A considerable amount of engineering manpower was required to "conceptualize" a process flowsheet. After sketching the flowsheet layout, the engineer was still faced in most cases with a time-consuming reduction of his graphic concept of the problem to numerical data required by the balance program. Furthermore, output from these early systems was usually in tabular numeric form. The computer results then were transferred manually to a pictorial representation of the process. A new process design balance system has been developed which runs on a popular and inexpensive personal computer. This system combines modern Computer Aided Design (CAD) principles and the graphics capabilities of the personal computer to allow the process engineer to define a flowsheet problem while creating a process flow diagram. The system provides balance results in both pictorial and tabular form. Past, present, and potential applications of the system are discussed, and an analysis of the cost benefits derived from its use are provided.

Jan 1, 1985

By Paul Saxton

INTRODUCTION AND SUMMARY This short paper deals with the history of the Nickel Plate Mine from 1898 to 1987, with the major focus on the time period 1984 to 1987. Operations from 1898 to 1955 are reviewed in a cursory manner with the emphasis on some interesting points in the early 20th century. A review of the major exploration work carried out in 1984 to 1987 is presented and the process of moving the project through feasibility, government permitting and construction is described. The Hedley gold camp is situated approximately 40 kilometres east-southeast of Princeton, in southern British Columbia. The area has had a long history of gold mining and between 1902 and 1955 approximately 1.5 million ounces of gold were won from several mineralized skarn orebodies. Most production came from the Nickel Plate and Hedley Mascot mines. AN EARLY TO MID 20TH CENTURY SUMMARY The Nickel Plate is one of the oldest mines in the province. The mine had operated from 1904 to 1930 and, after a period of shutdown, from 1934 to 1955. The mine was revived in 1967 for exploration and. will resume production during the first half of 1987. In the first period the Yale Mining Company and Daly Reduction Company operated for six years and Hedley Gold Mining Company for twenty-one. In the second period the mine was operated by the Kelowna Exploration Company Limited and Kelowna Mines Hedley Limited for twenty-one years. In the present period the mine has been revived by Mascot Gold Mines Limited.

Jan 1, 1987

By P. James

"INTRODUCTION High sulfate (SO4-2) levels often occur in MIW (mining influenced water) either as the result of oxidation of sulfide minerals exposed by mining activity or by deliberate addition – commonly by sulfuric acid (H2SO4) use in hydrometallurgical leaching activities. Increasing regulation of sulfate discharge is creating new pressure to treat or mitigate sulfate release to prevent its entry into the environment. Current treatments include precipitating as gypsum during lime treatment, filtration separation using membranes such as reverse osmosis and nanofiltration technology, and biological elimination via methods like constructed bioreactors. Blue Planet Strategies (BPS) focuses on improved resource utilization targeting electrolytic treatment and waste conversion into resources and has now demonstrated that its proprietary DEMET™ (Dynamic Electrolytic Metal Effluent Treatment) platform can also remove sulfate from target streams as a byproduct of its usual primary treatment focus points of metal species elimination and/or pH adjustment.[1-6] This powerful new capability can mitigate sulfate contamination and recover the sulfate in a useful and potentially saleable form as a byproduct of improved primary treatments focused on enhancing production or treating waste. This provides a new treatment opportunity and value proposition for lowering overall sulfate consumption/addition or creating new revenue to defray conventional treatment costs. The DEMET Alternative DEMET utilizes a patented electrolytic technology platform employing proprietary dynamic high surface area electrodes in innovative configurations to achieve a variety of novel selective chemistries. DEMET‘s unique elements can yield higher processing rates at practical efficiencies, lower energy consumption, plus improved processing stability and lower maintenance requirements due to enhanced resistance to cell fouling and shorting; while also thwarting cross stream (catholyte vs. anolyte) contamination. Consequently, DEMET can provide a superior, extremely versatile, and cost-effective electrolytic treatment option where a multitude of FEED and PRODUCT stream combinations might be employed in comparison to traditional tankhouse electrolytic cells. Secondary reactions (Figure 1A) which could also occur at the cathode (plating/electrowinning, precipitation/scale formation, etc.) are controlled through process tailoring and operation parameter selection. Additionally, DEMET‘s innovative dynamic system mitigates potential fouling and electrode occlusion or shorting challenges which could occur when process particulars demand some of these secondary side reactions occur."

Jan 1, 2015

By H. R. Quina

Phosphate is one of the most important minerals in our world today. It contains the life-giving element of phosphorus, which is essential to the growth of every living cell in plant, animal, and man. This vital mineral is found in twenty-three states of the United States; however, for more than 70 years, Florida has led the nation in phosphate-production and now produces 70% of the requirements of this country. Since the early 1880% when rich phosphate deposits were accidentally discovered in a river-bed in Central Florida, the industry has developed into a multi-million-dollar operation. Phosphate mining began in Florida in 1887 with very crude methods and equipment. The original process was necessarily slow and tedious, resulting in total production of 3000 tons in 1888. Progress was made in improved mining operations, and by 1894. Florida had grabbed the lead as the nation?s largest phosphate-producing area, and is still in the top position.

Jan 1, 1962

By Britta Schoesser, Zdenek Zizka, Markus Thewes

"The support pressure of a slurry shield corresponds to the in situ earth and groundwater pressure to ensure the stability of the tunnel face. The support fluid (bentonite suspension) penetrates from the excavation chamber into the pore space and transfers the support pressure to the granular structure of the soil within this zone. At the same time, the cutting tools rotate periodically with the cutting wheel and remove the penetrated soil up to a certain cutting depth at the face. Shortly after the tool passing, the penetration process starts again. Both, the support pressure and the soil excavation, act in the same direction at the tunnel face, but they are subject to different cyclic intervals. This relationship between the time needed for the transient penetration process and the interval of the cyclic passage of the cutting tools at a local point at the face is examined and the impact onto the global face stability is discussed. INTRODUCTION Slurry shields are usually deployed for excavations in soft ground. The main application range is in non-cohesive soils (DAUB Recommendations 2010). In non-cohesive granular soils, the tunnel face stability is one of the key design issues. The slurry shields make use of pressurized bentonite suspension (slurry) to support the unstable tunnel face. To support the tunnel face effectively, the slurry pressure has not only to counter the groundwater pressure, but also has to be transferred into an effective stress to support the soil grains. In general, the pressure transfer can be achieved in two ways: (1) with a thin flexible membrane or (2) a penetration zone. The membrane (1), called filter cake, creates a thin impermeable layer from bentonite particles directly on the tunnel face, and enables a transformation of excess slurry pressure into effective stress. In case of penetration zone formation (2), the excess slurry pressure is transferred onto the soil skeleton along the entire penetration depth by shear stresses between slurry and soil grains. These theories, presently applied to assess the pressure transfer on the grains within slurry shield tunnelling, are originating from diaphragm wall technology, e.g. Müller-Kirchenbauer (1977), Kilchert and Karstedt (1984). They assume that the support pressure transfer mechanism is built-up instantaneously on the whole tunnel face and is not damaged or influenced by the interaction with excavation tools. These assumptions are valid for conditions during the excavation of diaphragm wall trenches whose bottom is excavated and the walls of the trench are supported. At the tunnel face of a slurry shield, the support suspension acts on the same area as the soil excavation. Hence, the conditions on the tunnel face are transient (time dependent) due to the time period needed for the penetration process of the slurry and the periodical damage of the pressure transfer mechanism by excavation tools (Fig. 1a)."

Jan 1, 2016

By James N. Orlich

Meridian Gold Company's Royal Mt. King mine (RMK), a subsidiary of FMC Gold Company, is located approximately 40 miles east of Stockton, California on the western edge of the historic mother lode belt. Gold ore at RMK is associated with a series of northwest trending fault zones hosted in either meta-volcanic or meta-sedimentary rock types commonly referred to as greenstone sulfide and carbonaceous phyllite. Mineralogy studies show gold in both ore types to occur primarily as electrum in the form of 1 -20 um inclusions in pyrite with varying amounts of free milling gold. In carbonaceous ores, gold was not found to be closely associated with carbon. At the start of the current mining operation, three major ore resources were identified. North Pit and Gold Knoll pits were the major greenstone reserves while Skyrocket Pit contained over 60% of the total reserves as carbonaceous ore. Since North Pit and Gold Knoll were to be the first areas mined, the mill began operation in February 1989 with a flowsheet designed for greenstone ores with a carbonaceous expansion anticipated after depletion of the greenstone reserves.

Jan 1, 1992

By James P. Cooney

The global mining industry is in the process of redefining its activity and purpose in terms of sustainable development. This process is impelling a growing number of companies to engage their stakeholders on environmental and social issues. Nongovernmental organizations (NGOs) have customarily acted as critics of the mining industry's performance. A new relationship between mining companies and NGOs is emerging in the context of sustainable development, ranging from dialogue to joint action. If positive interaction among mining companies and NGOs is to succeed, clear terms of engagement must be articulated, and measurable progress toward achieving both corporate and NW objectives must be demonstrated. The experience of Placer Dome is illustrative of the rewards and challenges of engaging with NGOs.

Jan 1, 2001

By C. J. Pritchard

Controlled recirculation of ventilation air in underground metal and nonmetal mines has the potential to improve airflow and the health and safety of miners when implemented properly. Previous research by Robinson, Marks, Cecala and others concluded that the success of a district recirculation system is predicated upon an adequate supply of fresh air and the use of a reliable monitoring system for safe operation. This recent research also showed that contaminant levels will not exceed pre-recirculation levels, and that district recirculation can improve the dilution of face contaminants, especially methane gas. To illustrate the process of implementing controlled recirculation and also to promote and give guidance to mine operators in consideration of this tool to improve mine airflow, Office of Mine Safety and Health Research (OMSHR) researchers acquired baseline airflow and contaminant data from a multi-level room-and-pillar nonmetal mine and used commercial ventilation network software to simulate base case conditions and recirculation of mine air. Mine return air baseline contaminants of dust and diesel particulate matter were at lower levels than intake air, providing the potential for improved face air quality. A ventilation model implementing controlled recirculation was developed and analyzed, showing an increase in air quantity at the face, improved intake air quality, and contaminant exposure levels below those set by statutory requirements. These results, along with conclusions reached by previous researchers, provide the basis for examining the safe and effective implementation of controlled recirculation in metal and nonmetal underground mines using this mine as an example.

By John D. Nelson

Unprotected uranium mill tailings impoundments can pose a significant risk to nearby inhabitants and the surrounding environment in the event of a prolonged or catastrophic release of contaminants contained in the tailings. As a result of this potential, reclamation plans for such facilities must include engineering designs to protect against disruption of the tailings and the potential release of radioactive materials. The goals for such engineering designs should be to provide overall site stability for long-term periods with no need for planned ongoing maintenance and to provide a repository for the tailings that will not place a burden on future generations. Although the goal is to provide a maintenance-free system that does not require monitoring, it must be recognized that some period of surveillance would be reasonable. The surveillance period could be relatively short and only needs to assure with reasonable confidence that the reclamation scheme that was implemented is functioning adequately. An investigation was conducted by Nelson, Volpe, Wardwell, Schumm and Staub (1983) entitled Design Considerations for Long-Term Stabilization of Uranium Mill Tailings Impoundments (NUREG/CR-3397). This report assesses the degree of confidence with which long-term reclamation plans can be expected to remain effective over specific periods of time, and to assess the additional effort required to extend the design period from one long-term period to a longer one. This paper presents a summary of that investigation and discusses some of the important conclusions.

Jan 1, 1984

By A. D. Hammond

Vanadium is a transition metal, ductile, silver-gray metal. It is harder than most metals and steels and it has a good resistance to corrosion, it is stable against alkalis, sulfuric and hydrochloric acids. Vanadium is oxidized in air about 660 °C, although an oxide layer forms even at room temperature. The chemistry of vanadium is noteworthy for the accessibility of the four adjacent oxidation states 2-5. In aqueous solution the colors are lilac V2+, green V3+, blue VO2+ and, at high pH, yellow VO42-. Considered to be as abundant as zinc, metallic vanadium is not found in nature, but it is known to exist in about 65 different minerals. Economically significant examples include patronite (VS4), vanadinite (Pb5(VO4)3Cl), associated to the uranium mineral carnotite (K2(UO2)2(VO4)2?3H2O) and in a vanadium mica called, roscoelite K(V3+,Al,Mg)[(Si,Al)4O10](OH)2. Other important vanadium ore oxides are montroseite (V,Fe)O(OH) and corvusite (Na,Ca,K)V8O2.4H2O. Much of the world's vanadium mine production comes from magnetite-hosted deposit and to a lesser extent, in sedimentary-hosted sandstone. Vanadium is also present in bauxite and in fossil fuel deposits such as crude oil, coal, oil shale and tar sands. In crude oil, concentrations up to 1,200 ppm have been reported. A significant vanadium production comes from the processing of petroleum residues, fly ash and recycling spent catalysts. In 2011, metallurgical applications accounted for 93% of the use of vanadium. Here, an alloy called ferrovanadium is utilized to strengthen steel to be used as rebar in the construction industry, in the manufacturing of axles, crankshafts, gears and chassis in the automotive and transportation industries and in the manufacturing of high-speed tools. In the aerospace industry, vanadium is utilized as a titanium alloy in the manufacturing of airframes and jet engines. The reason for the wide use of vanadium as alloy is its high strength-to-weight ratio, the highest of any engineered material on earth. The major non-metallurgical use of vanadium is in the production of catalysts for the chemical industry. The most commercially important compound is vanadium pentoxide (V2O5), which is used as catalyst in the production of sulfuric acid.

Feb 23, 2014

By Ramesh Kumar Chauhan, Umakant Sharma, Manwendra Pratap Singh, Ashok Kumar Chadha

The power sector in India has an installed capacity of 267.637 GW as on March 2015. Out of this total installed capacity, the hydropower sector contributes 41,267.43 MW as renewable energy source. The development of various proposed hydropower schemes in India are primarily concentrated in mountainous regions of Himalaya and often involves underground tunnelling. Underground tunnelling of considerable magnitude is generally associated with adverse geological conditions and associated geological surprises. The main objective in case of Tunnels constructed especially for hydro projects, which carry enormous quantum of water is that, it should not leak. Moreover, the tunnels which are part of water conductor system should resist the inflow of water from the surrounding ground in order to avoid draining of natural water sources and lowering of existing groundwater levels. Lowering of water table may result in subsidence and damage to existing surface structures, loss of capacity of drinking water schemes and in some cases even catastrophic sliding of landmass. Grouting and pre-grouting in tunnels serve three different purposes i.e., Stabilization, Strengthening and sealing of the rock mass around tunnels to avoid leakage of water from tunnels. In present paper, results of grouting methodology adopted during final construction stage of RHEP (412 MW) along with the introspection of Water Pressure Tests conducted for determination of the efficacy of grouting were elaborately presented. The process, of contact and consolidation grouting which is respectively followed by water pressure tests along entire reach of HRT (15.177 Km long) were also addressed in detail. Pertaining to the results of water percolation tests (before and after consolidation grouting), it was also attempted to categorize the behaviour of different rock mass classes/ conditions in reference to different quantum of grout intake and corresponding Lugeon values. Importance of planned and dedicated successful grouting procedure adopted in hydropower project at RHEP is also emphasized.

Jan 1, 2016

By Jun Yuan

Kaolin clays from five different commercial deposits in Georgia were studied to understand the variations of zeta potential and related fundamental properties. The results suggest that higher negative zeta potential is related to exchangeable or soluble calcium ions in the clays.

Jan 1, 1997

By E. Bakhtavar

Finding a ?practical spacing between the holes? for use of the expansive mortars is an important problem in dimension stone quarries. Objective has been to first introduce a relationship between this spacing and the dependent parameters in such a way that the required size and shape of the blocks is produced with the maximum efficiency and safety, minimum wastage, conservation of reserves and protection of environment. For this purpose, a dimensional analysis was used. On the basis of granite and marble rock types in Iran two separate relations are hence established to calculate the practical spacing between the holes.

Jan 1, 2011

By J. Groppo, W. Zhang, R. Honaker

"Rare earth elements (REEs) found in coal are in the form of minerals, ion-substitution with clays and organically bound. Rare earth minerals (REMs) such as monazite exist in coal and have a grain size less than 5 microns. Froth flotation was successful in concentrating REMs existing in a thickener underflow material derived from Fire Clay seam coal which contained around 300 ppm of rare earth elements (REEs). Conditioning with fatty acid followed by processing using multiple stages of conventional flotation produced a final concentrate containing 2300 ppm REEs. Using a laboratory flotation column, a concentrate containing around 4700 ppm of total REEs was produced equating to an enrichment ratio of 10:1. INTRODUCTION Rare earth elements (REEs) are becoming increasingly important and have been widely used as raw materials for the production of phosphor, metal catalysts, magnets, and batteries [1, 2]. REE recovery from alternative sources such as coal and coal by-products has the potential to stabilize the economic viability of coal mining operations while providing a dependable supply of critical materials. The average REE content of the world coal is around 60-70 ppm [2]. There are many well-known coal beds with high contents of REEs such as those in the Far East coalfields in Russia (300-1000 ppm), the Fire Clay coal seam in eastern Kentucky (500 ppm), and the Sydney Basin in Nova Scotia, Canada (72-483 ppm) [3-6]. The occurrence of REEs in coal and coal by-products can be classified into three types, i.e., rare earth minerals such as monazite and xenotime, ion exchangeable REEs in clays, and REEs associated with organic matrix. The particle size of the rare earth (RE) minerals in coal and coal by-products is very small and normally in the micron and/or nanometer scales. The flotation technique, which is based on the surface chemistry difference, has been widely used to treat fine rare earth industrial minerals such as monazite, xenotime, and bastnaesite [7-11]. As such, flotation is a promising method for the concentration of REEs from coal and coal by-products. In the current study, rare earth flotation was conducted using the fine coal refuse generated at an operating coal preparation plant treating coal from the Fire Clay seam. REE concentration by flotation required an appropriate amount of grinding and control of the pH value while using typical collectors. Prior to RE concentration, release tests were conducted to evaluate the floatability of the recoverable coal and the REE distribution in the flotation fractions in the fine refuse. Mineralogy of the REE was studied using SEM-EDX."

Jan 1, 2017