Search Documents

By John M. Wootten

The development of new coal markets is -t upon the ability to utilize coal in an environmentally acceptable and economically viable fashion. Foremost in the concerns about coal utilization is the impact its combustion has on air pollution. Concerns over environmental issues, such as acid rain, are currently one of the major impediments to the development of new coal markets. The Department of Energy and the Synthetic Fuels Corporation are addressing certain aspects of the development of new technologies for the utilization of coal. However, at the present time, there is a void in the new technology development process. That void is the step from proof- of-concept to commercial demonstration. Congress has established the Clean Coal Technology Fund at a level of $750 million to fill this void. The Department of Energy, in a solicitation of interest, received over 175 proposals for commercial demonstrations of clean coal technologies. A review of these solicitations indicates that $1.2 billion worth of research could be accomplished with a federal cost sharing of $425 million or 35 percent of the total. Industry has indicated, through this response, its willingness to invest its limited funds on projects it feels have the greatest potential for the clean use of coal. What must now occur is that Congress must appropriate the monies from the fund to initiate the commercialization of these clean coal techno1ogies.

Jan 1, 1986

By R. J. Matetic

The impact of longwall mining on the local hydrological regime has become an important environmental focal point. Unfortunately, only a few studies have addressed the timing and range of well fluid level fluctuations and the associated ground movement. Furthermore, even fewer studies have determined the influence of longwall mining on water quality. The U.S. Bureau of Mines is providing insight into this environmental concern through a program of field case studies. One such study was conducted in Cambria County, PA where five observation water wells were drilled above two adjacent longwall panels. In this study, three wells were completed as nested piezometers and the remaining two served as producing wells. The piezometers were positioned along a line oriented subparallel to the longwall face and were located at the centerline of each panel and over the intervening chain pillars. The piezometers were designed to monitor fluid level fluctuations in both shallow and deep water-bearing zones. Slug tests were conducted before and after mining to characterize changes in hydraulic conductivity of the respective water-bearing zones. Pressure transducers and data loggers were installed to provide continuous fluid level fluctuation data as mining developed through the study area. The producing wells were drilled to provide water quality information. One well was located directly above the centerline of a panel and the other was positioned over the panel's set-up rooms. The wells were designed to simulate domestic use and were produced daily, for four hour intervals, throughout the study. Samples of the produced water were collected before and after mining progressed through the area. In addition, an array of monuments was installed near the study wells and was periodically surveyed to characterize mining-induced surface deformations. This study shows that: a) the observed changes in ground water chemistry did not affect the potability of the water; b) short-term major water level fluctuations occur at the approximate time of undermining; and c) water level recovery begins before the process of subsidence is complete.

Jan 1, 1986

By M. Sengupta

Surface mining in arctic regions is characterized by many unique problems. Continuous and discontinuous permafrost (perennially frozen ground) occurs in most of the arctic and subarctic areas. Permafrost presents special problems of slope stability. Stability of permafrost depends on its temperature, moisture content and material type. Permafrost slope fails due to solifluction, disturbance of ice rich slopes, and liquefaction. Drilling and blasting of frozen ground present special problems. Depending on their degree of saturation with water, freezing soils and rocks have a number of important characteristics that affect blasting efficiency. Metals used in mining equipment and mining structures require special selection. At low temperatures many steels lose most of their normal ductility and toughness (resistance to brittle fracture). The paper discusses engineering solutions to unique problems of arctic mining.

Jan 1, 1986

By Yoginder P.

ACKNOWLEDGEMENTS Authors sincerely appreciate the interest, cooperation and technical support of the coal company management and staff in conducting the study. Without their assistance this study would not have been possible. INTRODUCTION AND SPECIFIC OBJECTIVES An area in the midwest overlying abandoned room-and-pillar mine workings at, shallow depth has been experiencing subsidence movements with associated damage to surface structures. Other coal companies in the area have also been having similar experience. A 16 - month cooperative study between a mining company and the Department of Mining Engineering at SIUC was developed with the following objectives. 1) Determine the extent to which surface and subsurface movements were complete in the area, 2) Identify the mechanism(s) of subsidence in the area, 3) Determine the influence of geology and hydrology of the area on subsidence movements, 4) Observe the conditions of abandoned underground workings with a borehole TV camera, 5) Characterize the extent of damage and monitor possible progressive damage to selected surface structures, and 6) Make recommendations to a) minimize further damage to surface structures in the area, b) identify future areas that may be affected by these movements and c) modify mining systems to minimize these movements.

Jan 1, 1986

By S. S. Peng

This paper presents a computer program package for predicting surface movement and deformation caused by under-ground coal extractions. It is capable of: predicting final surface movement and deformation over underground openings; predicting dynamic surface movement and deformation process associated with underground lingual mining operations; processing and bookkeeping subsidence survey data; recommending subsidence parameters for those new coal mines where no subsidence data are available; and deducting subsidence parameters from collected subsidence data.

Jan 1, 1986

By J. C. Haptonstall

Stoping methods at the Homestake Gold Mine through 1978 had been traditional overhand cut-and-fill, shrinkage or square set. High costs, low-productivity and safety concerns prompted the mine to search for and adopt a "bulk mining" technique as a primary stoping method. Blasthole stoping had been successful but it is very development intensive, and was not suitable for the mine's accelerated mining program. Vertical Crater Retreat stoping was selected, and today accounts for over 50% of ore production. Case histories representing both the successes and failures of VCR stoping in the mine are discussed.

Jan 1, 1986

By D. S. Choi

The paper presents the result of analysis of subsidence data collected from coal mines operating in Northern West Virginia and Southwestern Pennsylvania. A particular emphasis la placed on the measurement of the angle of draw for the protection of surface structures.

Jan 1, 1986

By Yu. P. Astafyev

The, control of drilling and blasting is a complicated dynamic system whose aim is to ensure safety and prepare rock of required grade and the standard level of broken material reserves Unlike other processes drilling and blasting, as an object have the following features: -a large variety of drilling and blasting methods due to specific conditions of blasting, various types of drilling equipment, schemes-of blasting, types of explosives and others; -relative continuity of drilling, the character of mammoth blasts being discrete; -increased requirements to the safety of blasting;; -a great. number of control parameters, some of them having a qualitative characteristic but not a quantitative one; -availability of feedforward and feedback with other mining processes in terms of time and space. These features predetermine the hierarchical structure of an automated system of planning and control of drilling and blasting (fig.1). The system is implemented on the basis of unity of the data base and in interre lation with other problems of controlling mining operations. An automated system of this kind makes it possible to take optimal decisions actually on all the levels and stages of operations, with rock having been blasted before extraction.

Jan 1, 1986

By F. C. Schwerer, C. R. McKee, J. C. Seccombe

Production of methane from coal seams requires hydrofracturing, and the length of a hydraulic fracture determines we11 spacing. Since the volume of fluid injected is known, the fracture length is the volume divided by average width and height. If the fracture is contained in the known height of the seam, then fracture width becomes the major factor con- trolling length. Width is proportional to coal compressibility; bulk compressibility is known to be larger than intrinsic compressibility. A method is given here to measure in-situ compressibility (a) from transient pressure testing. Theory linking flow in porous media with rock mechanical properties is reviewed. A consistent derivation of the porous flow equation is given incorporating 3-D deformation and the effective stress parameter "st' linking changes in effective stress and pore pressure. The relations for "st' in terms of a and intrinsic compressibility (ai) are substituted into the field measured porosity-compressibility product (net) and solved for a, the constrained matrix compressibility. In a field example, using 4 wells with an anisotropic analysis, the ratio of major to minor permeability was 17 for the Pratt A seam. a was found to be 6x10-5/psi as opposed to the laboratory value of 1.4x10-6/psi.

Jan 1, 1986

By J. A. Herbst

A state of the art computer simulation package, named UTAH-MODSIM is being developed. This package can run on a mainframe (eg. UNIVAC) as well as on a microcomputer (eg. IBM/PC with at least 512 kBytes of core memory). Friendliness was the major concern in developing this software. The user simply generates a complete flowsheet by presenting the flowsheet on a graphics terminal. This flowsheet defines the circuit to be simulated. With the minimum required data, the user can obtain a complete mass and water balances within a few minutes. Moreover, this package will provide scale-up and capital cost information of specified equipment relevant to design. In order to illustrate the utility of this software, three design examples are given. They are: a) A typical multistage crushing plant. b) A reverse closed grinding circuit comparing one stage with two stage classification. c) A standard closed grinding circuit suitable to liberate a specified fraction of chalcopyrite from a copper ore.

Jan 1, 1986

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

The literature on four different topics is re¬viewed herein for purposes of mathematical mod¬eling of mine water inflow. The first of the topics reviewed is modeling of fissured or fractured ma¬terials; the second is general Darcy based flow models; the third is field methods for determining fracture flow properties; and the fourth is methods used presently for determining mine water inflows. The four topics are considered in the foregoing order. FRACTURE FLOW MODEL Two basic types of fracture flow models have been developed. The first type uses various tech¬niques for space averaging to obtain the equations. Systems are considered in which the porous media properties vary smoothly enough and the fracturing is sufficiently profuse and well distributed that the locally averaged properties are meaningful when viewed on the macroscopic scale. The final result is that a coefficient is used which is similar to saturated hydraulic conductivity and in many cases, simply is hydraulic conductivity. In other cases, the coefficient is apparent hydraulic conductivity be¬cause the response from flow in the fractures is more rapid than flow in the pore spaces. Faust and Mercer (1980) refers to this method as the contin¬uum approach. Some of the papers on this type of problem are by Duguid (1973), Verner et al. (1974), Owili-Eger (1975), Duguid and Abel (1974), duPrey and Weill (1974), and O'Neill (1978). Duguid and Lee (1977) also considered heat flow in the fluid and the porous medium. These papers all result in various types of computer programs. Some papers on this topic that do not result in computer programs are by Snow (1968, 1969) and Streltsova (1976). Some of the foregoing articles consider con¬solidation of the porous media and the resulting effect on hydraulic conductivity. Barenblatt et al. (1960) developed an analytical solution for fracture flow and discussed the time that is involved in the drainage process and the effect that fracture flow has on the drainage time. The second type of fracture flow model con¬siders the width of the fractures as a function of the pressure in the field. Faust and Mercer (1980) refers to this method as the discontinuum approach. This approach often requires two finite element programs that consider the stress in the material and the flow in the fractures separately. The pro¬grams are then linked to arrive at the final solution. Some of the articles that consider the interrela¬tionship between pressure and the size of the frac¬ture but do not use computer solutions are Gringarten et al. (1975), Narasimhan and Palen (1979), and Witherspoon et al. (1979). Papers that use a linked computer program between stress and flow are by Ayatollahi (1978), Gale et al. (1974), and Noorishad et al. (1971). Ayatollahi's program is primarily for the petroleum industry because it does not consider the effect of gravity. Ayatollahi assumes that pressure effects are very large in com¬parison to gravity effects. This assumption would apply only to very deep aquifers. Articles that consider fracture flow on a more applied basis are by Wittke et al. (1972), who con¬siders that the flow is entirely through fissures and negligible through the pores of the rock. Gringarten and Witherspoon (1972) developed type curves that may be used for analysis of fracture flow systems; the curves are based on the assumption that it is possible to distinguish between aquifers with hor¬izontal and vertical fractures and that it is possible to analyze the system as an equivalent anisotropic homogeneous porous medium with a single fracture with much higher permeability. DARCY FLOW MODELS The Darcy flow models of greatest interest to mine water inflow prediction are those which allow

Jan 1, 1986

Slurry technology developed for the marine transport of mineral commodities has been increasingly applied to on-shore slurry transport systems. Reclaim of mineral concentrates, sand tailings for mine backfill and various industrial minerals from storage tanks or ponds normally require a slurry of high density at constant flow rates to improve process performance and to reduce handling costs. An efficient system must accomplish this at minimum capital costs with maximum reliability. Continuing improvements in equipment design to improve repulping efficiency and their application are discussed.

Jan 1, 1986

By Christopher J. Bise

INTRODUCTION Before a mine is planned in detail, a preliminary analysis is often conducted. This preplanning permits the mining engineer to make a rapid assessment as to whether or not a particular mining property warrants further consideration. In fact, a properly conducted preplanning phase can come within 10% to 20% of the actual results, thereby saving the mining engineer valuable time before committing himself to a fine-tuned analysis. The questions to be answered by mine preplanning are (1) What will be the operating conditions for the mine? and (2) How long will it take to complete the project? To answer these questions, calculations dealing with reserve estimation, production planning, man- power planning, and project scheduling are conducted. The following sections discuss these various phases of mine preplanning in greater detail. RESERVE ESTIMATION The estimation of the various characteristics of a reserve, such as quantity, grade, and thickness, is an ongoing process throughout the life of a mining venture. However, the reserve-estimation phase of mine planning is more closely associated with the preplanning phase. There are many different techniques employed in reserve estimation of solid mineral deposits; variations among them are introduced because of such considerations as ease of application or level of accuracy. In any event, each technique is developed in the following manner: (1) the mineral body is represented pictorially and then subdivided into blocks related to one or more samples of exploration data, (2) the area and volume of each block is determined, (3) the volumes are converted to representative tonnages (or, for example, grades), and (4) the results are tabulated. To illustrate this procedure, the polygonal (area-of- influence) technique will be presented due to its ease of application, flexibility in dealing with different deposits, and general acceptance. The polygonal method assumes that all characteristics of a mineral body extend halfway between a point of observation and any other point of observation. The explored portion of the mineral body is represented by polygonal prisms whose depths relate to the characteristic in question (grade, thickness, etc.) and whose plane bases relate to the area of influence of each point of observation (drill hole, etc.) as shown in Fig. 1. The polygons must be constructed in a definite order, usually clockwise and from the periphery to the center of the deposit. Table 1 can then be used to calculate the characteristics in question. Since, by definition, the polygonal method assumes that the characteristics of a mineral body extend half- way between points of observation, it becomes readily apparent that the evaluation of a vertical-drill hole exploration program requires that the sides of the polygons be formed by the intersection of perpendicular bisectors (Fig. 2). Figs. 3 and 4 show correct and incorrect construction of the polygons. The criterion for correct construction of the polygons is that all points within a particular polygon must be closer to its rallying point than those located in any other polygon. This is clearly not the case for certain points that are located in the polygon containing rallying point B in Fig. 4. Although this method can be used where the drill holes are irregularly spaced, calculations become less tedious when a square net (Fig. 5) or a chessboard (Fig. 6) grid is adopted. The numbers shown in Figs. 5 and 6 represent the relative weight for each of the shaded areas. In general, the greater the number of polygons, the more continuous the mineral body, and the more regular the grid, then the more accurate the computations will be. PRODUCTION PLANNING Before an acceptable evaluation of the production potential of a mine can be determined, a thorough exploration program should be conducted. It seems obvious that the nature and properties of the deposit and adjacent strata, the presence of impurities, and other mining conditions should be adequately determined prior to production planning and equipment selection. The lack of sufficiently detailed knowledge of the many mining parameters has led to the failure of numerous operations. For example, targeted production tonnages and equipment sizes for a coal mine are intimately related to the seam thickness. Needless to say the quality of information that is gathered from an exploration program can have a tremendous impact on the production plan. Production plans are developed initially by determining reasonable shift tonnages per operating section. Most of the time these values are developed from his-

Jan 1, 1986

By S. K. Kawatra, Harrison R. Cooper

In the last 30 years, on-¬stream slurry analyzers have proven to be of great use in the control of mineral processing circuits. This review discusses the two most popular methods, x-ray fluorescence and neutron activation analysis, and also considers techniques which are still under development.

Jan 1, 1986

By Michael R. Birkos

A new electrotelluric prospecting technique allows the mapping of ore body distribution, lithologic contacts, and voids with accurracy comparable to core drilling. Data is available almost immediately and presented in a format similar to a downhole log. This is done with a passive surface receiver that transduces electrotelluric radiation into an audible signal. Changes in the character of the audible signal lends insight into lithology, porosity, fluid type and medium. Three case histories are presented. The first delineated a paleochannel within a coal seam. The second traced old mine workings and backfill areas. The third identified a high-pressure karst void.

Jan 1, 1986

By Keith A. Heasley

At this point in time, approximately 800 M tonnes (880 M tons) of coal are mined each year in the United States. Forty percent of this coal or approximately 320 M tonnes (350 M tons) is taken from underground coal mines, and from this subtotal 16% or 50 M tonnes (55 M tons) is from longwall panels (1). If, for the sake of argument, an aver- age extraction thickness of 1.5 m (5 ft), an aver- age extraction ratio of 50 percent and an in situ density of 1360 kg/ms (85 lb/ft3) for this coal are assumed, then the 320 M tonnes (350 M tons) of underground coal translates to over 310 km2 (76,000 acres) that is undermined each year. Con- sidering that the total U.S. production of under- ground longwall coal to date is approximately 345 M tonnes (380 M tons), then a total of approximately 165 km2 (41,000 acres) (considering 100% extraction) has been directly undermined by longwall coal production in the United States. If the angle-of- draw is considered, the total area affected by longwall subsidence in the United States is probably twice the above value or 330 km2 (82,000 acres) . In the future, a number of other miscellaneous factors seem likely to multiply the number of potentially damaging situations that occur due to longwall coal mining. First, the overall production of coal in the United States is expected to gradually increase. This factor is further com- pounded by both the fact that the percentage of the overall production due to underground mining is bound to increase, since the vast majority of U.S. reserves (68%) are only recoverable by underground methods, and the fact that the percentage of the underground production of coal that is recovered by longwall mining is drastically increasing (1). Finally, as the nicest underground reserves are depleted, the remaining reserves will tend to be deeper, which increases the affected surface area, and under denser population concentrations, which increases the likelihood and severity of possible damages. Overall, considering the number of factor which are biased towards increasing the amount of undermined acreage, it appears that there must certainly be a corresponding increase in the number of possible damaging situations due to longwall-induced, ground subsidence.

Jan 1, 1986

By R. Bhaskar

The results of an experimental study on the dispersion and deposition characteristics of fine coal dust in mine airways are presented. Experiments were conducted at various flow velocities using bituminous and semi-anthracite-coal dust which had a large proportion of dust in the respirable size range. Cross sectional variations in the concentration of dust at various points in the airway were also measured. Instruments used in the experiments included gravimetric samplers and impactors. Concentration measurements were made both for the respirable and total airborne dust. The experimental design, sampling procedures and results are discussed. The study is aimed at providing a better understanding of the temporal and spatial behavior of dust particles in underground mine airways.

Jan 1, 1986

By C. E. Stack

For the purposes of this presentation, "refractory clay" is intended to include any clay suitable for refractory products and thus represents a description based on industrial application. Other common examples based on use would be white-ware clay, bleaching clay, paper clay, or cement clay. Most users and producers of refractories have specific quality requirements which determine the quality or type of clay that can be utilized. Many clays can however be interchanged or substituted in use by changing manufacturing processes or upgrading less desirable clays. U.S. Bureau of Mines publications (Ampian, 1985) categorize days into six groups. These are kaolin, fire clay, ball clay, bentonite, fuller's earth, and common clay. These are practical groupings based on clay production and usage in the United States. Among these groups bentonite, fuller's earth, and common clay are primarily composed of the minerals, smectite, illite, or chlorite, and are non-refractory. Kaolin, ball clay, and fire clay are commonly used in refractories and thus qualify as refractory clays.

Jan 1, 1986

By Michael Fehler, Hidenshi Kaieda, Leigh House

Hydraulic fracturing has gained in popularity in recent years as a way to determine the orientations and magnitudes of tectonic stresses. By augmenting conventional hydraulic fracturing measurements with detection and mapping of the microearthquakes induced by fracturing, we can supplement and independent1 y confirm information obtained from conventional analysis. Important information obtained from seismic monitoring includes: the state of stress of the rock, orientation and spacing of the major joint sets, and measurements of rock elastic parameters at locations distant from the wellbore. While conventional we1l 1ogging operations can provide information about several of these parameters, the zone of interrogation is usually limited to the immediate proximity of the borehole. The seismic waveforms of the microearthquakes contain a wealth of information about the rock in regions that are otherwise inaccessible for study. By reliably locating the hypocenters of many microearthquakes, we have inferred the joint patterns in the rock. We observed that microearthquake locations do not define a simple, thin, planar distribution, that the fault plane solutions are consistent with shear slippage, and that spectral analysis indicates that the source dimensions and slip along the faults are small. Hence we be1 ieve that the microearthquakes result from slip along preexisting joints, and not from tensile extension at the tip of the fracture. Orientations of the principal stresses can be estimated by using fault plane solutions of the larger microearthquakes. By using a joint earthquake location scheme, and/or calibrations with downhole detonators, rock velocities and heterogeneities thereof can be investigated in rock volumes that are far enough from the borehole to be representative of intrinsic rock properties.

Jan 1, 1986

By D. J. Shields

This paper describes a dynamic short-nun mineral supply model that incorporates secondary processing, transportation, mineral market structure, and direct mining and milling costs. The method employed is network flow programming. Empirical tests utilizing domestic phosphate industry data have been conducted by the Bureau of Mines, U.S. Department of the Interior. In the model, nodes represent physical locations such as a mine or port. Arcs represent either a process, such as mining, or movement, such as rail or barge transport. Each arc is described by lower or minims allowable flow bounds, upper or maximum possible flow bands, and variable cost. Mines and previous period inventories represent potential supply. The model is optimized via a cost minimizing algorithm, which attempts to fulfill stated total demand at the minimum possible system cost given the arc constraints. An optimal solution of the model will predict production patterns by mineral property for each prespecified level of demand. A mineral property is defined as a separate accounting entity such as a mine. The results of serial optimizations are used to construct the short-run supply curve. Dynamic policy analysis can be conducted by altering the arc constraints.

Jan 1, 1986