Search Documents

By H. Schultheis

The European Commission has launched in April 2002 the Thematic Network NESMI with-in the FP5 under Growth. NESMI stands for ?Network on European Sustainable Mining and Processing Industries? and will run until 2005. Within NESMI there are different ways to set up indicators and evaluate them throughout the NESMI Members. First analyses concerning the Demand and Competence within NESMI are developed. New focus points for analyses can be implemented into NESMI.

Jan 1, 2003

By Hugh E. Cronin, Lok Home

THE PENETRATION RATE BASELINE DILEMMA The penetration rate is the instantaneous advance rate of a TBM in a rock tunnel. Normally expressed in feet per hour. The production rate is the penetration rate multiplied by the number of hours worked and then factored by the actual utilization of the TBM. In a given rock formation, the actual production rate is a result of many factors some of which are within the control of the contractor and some of which are based on the route selected. Factors that are within the contractors control are cutter profile, frequency of cutter changes, thrust, rotation speed, cutter spacing and the efficiency of the operation. Factors that are site (route) specific are compressive strength, fracture orientation, fracture frequency, micro- fracturing, quartz content, Moh’s hardness, Cerchar Abrasivity Brazilian Tensile Strength and Youngs Modulus of the rock. In addition the following route speci?c conditions are beyond the contractors control; rockjointing, rock stress fault zones, water in?ow and rock decomposition; all of which effect production rate. Any one of the above defined rock properties, equipment specifications and actual operating usage will change the penetration rate. Furthermore, since the rock formation changes both in content and orientation as the tunnel advances, the penetration rate is constantly varying. The current industry practice in bidding tunnels is for each contractor to individually evaluate the rock hardness and other properties and from this information develop a penetration rate. All other factors being equal, the contractor using the most optimistic penetration rate will be the low bidder and be awarded the project. As this view is by definition optimistic, invariably the rock will be harder than the low bid assessment and the contractor will request additional compensation for the changed condition. The contractor will attempt to justify his optimistic assessment as reasonable by using expert supporting analysis. The above described example which is quite common at present in the industry tends to make the most optimistic contractor (at time of bidding) the contractor selected for the project whereas it is in the owners interest to contract with the most efficient contractor not the most optimistic. This situation is similar to the Geotechnical analysis that was prevalent in the industry over twenty years ago. Many projects have experienced a significant reduction of penetration rate from that which was originally estimated. In these cases the contractor often makes a claim for extra compensation based on the difference between the actual rock encountered

Jan 1, 2003

By Roe-Hoan Yoon, lsmail Yildirim, Jinhong Zhang

Inorganic fillers and pigments such as kaolin, diatomaceous earth silica, and talc were treated with various surfactants, and the changes in their surface properties monitored. When they were treated with a cationic surfactant, they became hydrophobic and the overall surface free energies were decreased substantially. The decrease in surface free energy was mostly due to the decrease in the acid-base component (ysab) of the surface free energy, indicating that hydrophobizing an inorganic pigment entails a reduction in ysab. It was found that the surface characterization technique employed in the present work was useful for studying the effects of using various other surfactants for surface treatment.

Jan 1, 2003

By Pratoomkhuan N. Lertsgoon

A large underground cavern with dimensions of 25m × 175m × 49m (W×L×H) was excavated in sandstone and siltstone to house 4 units of hydropower generator and was completed in 2000. In feasibility study stage, the property of the siltstone which governs the ceiling of the cavern was questionable due to slaking phenomenon. Parameters on rock properties for design were back calculated from actual ground response measured from a trial excavation. For safety of construction, comparison between prediction and actual ground responses during excavation had proceeded. The prediction was provided by means of PHASES and PHASE2 software and the actual rock response was detected by the provided monitoring system.

Jan 1, 2003

By W. Ghyoot, J. Boonstra, H. Dijkman, C. Buisman, M. Picavet

Paques and Umicore have demonstrated the feasibility of biological treatment of the highly complex Hoboken wastewaters in a1 m3/h pilot plant at Umicore Precious Metals, Hoboken, Belgium. In the first step arsenic was precipitated from copper smelter effluent as As2S3using biogenic produced H2S. Other metals such as copper, lead and cadmium were also removed as MeS to concentrations well below the discharge levels. Subsequently, sulfate and nitrate were removed to low concentrations (<300 mg/l and < 5 mg/l respectively) in high rate engineered bioreactors. Sulfide produced in the sulfate reduction process was recycled to step 1 for metals precipitation. Selenite/selenate was partly removed in the sulfide precipitation step, whereas the excess was biologically reduced and removed as selenium to concentrations <0.2 mg/l.

Jan 1, 2003

By Alex Lowson, Dan Tempelis

The Riverside Badlands Tunnel segment of the Metropolitan Water District of Southern California’s Inland Feeder Project, was lined with a segmented concrete primary lining and a welded steel final lining with the annulus filled with Low-Density Cellular Concrete (really a grout). The paper describes a numerical modeling technique that was developed to determine safe grout placement procedures to avoid pipe flotation, and shows the relationship between flotation and the rheology of the liquid grout. Design details of the steel liners are often not well suited to grout placement, and recommendations are given on how to improve this.

Jan 1, 2003

A new fluid bed lime calcining plant is converting high quality limestone into quicklime at the Cape Lime facility in Vredendal, South Africa. The plant was supplied by Metso Minerals. Cape Lime, established in 1946, operates two limestone and dolomite mines in South Africa. The high quality Vredendal limestone deposits are suitable for the production of lime for water treatment and for manufacturing precipitated calcium carbonate.

Jan 1, 2003

By Steve Kral

It seems that mining has been in the doldrums for awhile. Except for gold, metals prices remain depressed. And economic conditions in the United States and around the globe have put governments in a financial bind. This affects new building and infra-structure repairs, which, in turn, have a major impact the building materials industry. Add to that the severe environmental and regulatory restrictions placed on the mining industry in developing new mines and expanding existing ones. It’s enough to make a mining engineer/geologist/metallurgist go sell real estate. So why do those employed in the mining industry stay in the business and remain optimistic? Many of them will say that they have been through down cycles before and know that an upswing is in the offing. They also know that society will always need the commodities they produce. And they love the challenge. The challenge in mining’s case is producing commodities as cheaply as possible, in an environmentally sound manner and improving the quality of life in the communities where they work.

Jan 1, 2003

The status and outlook for mining, in your view. Minerals remain a major part of the world’s economic foundation. The fortunes of the mining industry rise and fall with general economic trends, but mining is no less important today on a global basis than it has been historically. Certainly, portions of the industry are critically depressed — domestic copper to name one area —but other sectors are prospering. Mineral consumption, both worldwide and in the United States, has increased steadily since the Great Depression, hitting all-time highs in 2000, the last year for which I have seen data. The highly developed economy in the United States tends to obscure the continuing importance of minerals here. But in less developed nations the critical nature of minerals is obvious and well accepted. In short, although there is no shortage of problems or challenges facing mining — there never has been — mining remains an essential business with great global opportunity.

Jan 1, 2003

By David McGregor, Ashoke SenGupta, Jerry Darlington

The stability of bentonite clay suspensions against flocculation in the presence of certain anionic polymers was investigated. These polymers included a purified sodium lignosulfonate, a sodium oxylignosulfonate, a potassium salt of humic acid, and a sodium polyacrylate. The polymers differed from one another in molecular weight as well as in carboxylic, phenolic, and sulfonate group contents. The scope of this study is in evaluating the extent of thinning achievable in a bentonite clay suspension in the presence of these anionic polymers under varying electrolyte concentration, presumably as a result of deflocculation of the clay platelets by the polymers. Under certain conditions of polymer dosage and electrolyte concentration, the lignosulfonate seemed to have flocculated the clay suspension, while the other polymers served fairly well as a deflocculating/dispersing agent. The lignosulfonate, however, showed some deflocculating ability when the electrolyte concentration of the suspending medium (water) was increased by adding sodium chloride to the clay suspension. Among the four polymers tested, the polyacrylate was found to be the most effective in deflocculating clay particles, followed by the humate and the oxylignosulfonate.

Jan 1, 2003

By Brent Duncan, Doug Harding, Bob Stier

The 73rd Street Tunnel Project is part of “The Tunnel and Reservoir Plan” (TARP)also known as the Deep Tunnel Project, and is located in the Village of Bedford Park, County of McCook, State of Illinois. The project consists of a ø 4.42 meter × 2,060 meter long (14´-6? bore, 6,760 foot)tunnel. The completed tunnel is used as a bypass tunnel for the McCook Cup Reservoir Project. The project was awarded to Affholder Inc. of St. Louis, in 2000. The paper describes the project in which a new, high-powered open gripper type main beam machine was used in which high advance rates have been achieved using conventional muck haulage techniques. Features of the project include the installation of rock support consisting of counter-sunk rock bolts that are required to be pull-tested for strength per project specifications. Installation and testing of the bolts are done during the boring cycle. Muck haulage was done by conventional muck car train and hoisting at the construction shaft. As the site layout did not include a tail tunnel, the trains needed to be shuttled at the shaft bottom. Even with the bolting requirements and the muck haulage without a tail tunnel, the Affholder site personnel still achieved high advance rates on the 73rd Street Project.

Jan 1, 2003

By L. Karka

The gold processing plant location in the Chalkidiki coastal area has been studied as a land use conflict case study in the context of a EU research program. The sustainability assessment of the plant establishment is made on the basis of a group of sustainability principles and criteria adopted in the framework of the SPECTRA project. Since the gold processing project has not been implemented yet its sustainability assessment is made on the documents submitted by TVX Gold during the procedure for the siting consent and the granting of environmental conditions. The assessment, appearing on a table, reveals an important effort to achieve a high degree of protection during the operation and after completion of the activity. The specific nature of the development and the knowledge of the local opposition in favour of tourism development have obviously influenced the priorities set.

Jan 1, 2003

By E. Stamboliadis

Gravity separation techniques were used in the early years to extract native metal nuggets and flakes from placer gold deposits. This was relatively easy for visible metal grains. As the size of the grain becomes smaller traditional gravity separation techniques become inadequate to recover native gold. Cyanidation was invented as a solution to the problem. According to it, gold and other precious metals are dissolved in water by sodium cyanide. The result was a drastic increase of world gold production but at the same time environmental issues were raised. In Greece gold mining has become equivalent with the absolute destruction of the environment and is under extinction. In the last years a new type of gravity equipment have been produced which create a gravitational field up to 200 G and can separate gold from gangue minerals at sizes below 50 µm. The strong gravitational field is created by centrifugal forces and the separation occurs in a fluidized bed, formed by water flow. Accumulations of finely disseminated native gold are found in the sedimentary sequence of the Flysch of the Ionian Zone. The main gold minerals are gold and electrum present as free metal flakes and micro nuggets in the size range between 5-250 µm. Test work, using the Falcon SB40 centrifugal concentrator, at the Department of Mineral Resources Engineering at the Technical University of Crete, has shown that this particular type of gold ore can be processed by gravitational methods that require no reagents and are environmentally safe.

Jan 1, 2003

By Brij M. Moudgil, Ivan U. Vakarelski, Yakov I. Rabinovich

Polymer and surfactant dispersant are widely used to disperse filler particles within a medium. Sur- faces active dispersants form self-assemble structures at the solid-liquid interface. The mechanical properties of the surfactant structures have been determined to strongly influence the dispersion behavior. In this study the atomic force microscope (AFM) is used to determine the elastic modulus and yield strength of a steric dispersant layer adsorbed to a rigid non-deformable surface. To interpret these values a model for elastic body contact based on a modified Hertz theory is applied. The results from this method may aid in the design of application-based dispersant systems.

Jan 1, 2003

By M. Gomilanovic

The Republic of Monte Negro (a member of the Serbia and Monte Negro federation) has 26 different mineral raw materials, 4 of which are recoverable and 22 unrecoverable. At present, 12 types of mineral raw materials are exploited. Based on these resources more than 80 facilities were built for the production and processing of mineral raw materials. The most significant of them are coal, bauxite and decorative and technical stone. Bearing in mind that all the mentioned mining facilities have significant impact on the living environment, and that Monte Negro was declared the ecological state, the objective of this paper is to present the experience acquired from this field of science.

Jan 1, 2003

By Steve Vaughan

Canadian Regulation and Reporting Requirements High reporting standards are essential in developing and sustaining a strong confident capital market. As of February 1, 2001, technical reports on mineral exploration and mining work, must conform to the standards of the Canadian Securities Administrators (CSA) National Instrument 43-101. Only a ‘qualified person’ may supply the technical information on which a news release is based and must verify that the final version of the release is accurate.

Jan 1, 2003

By Martin G. Taube, Dwayne A. Lewis

Drainage improvements at O’Hare International Airport, Chicago, IL included the installation of a drainage and storm water system to control the over?ow from nearby Willow Higgins Creek. This involved construction of a weir structure at the creek and the channeling of water from the weir to a newly constructed reservoir via three, 3.7-m(12-ft) diameter, underground storm sewer lines. The sewer lines passed beneath an existing, 2.3-m (90-inch) diameter high-pressure water main, which was to remain in service throughout sewer line installation. The soil composition around the water main ranged from medium stiff clays to silty sands and sandy silts. Triple-fluid jet grouting was used to stabilize the variable soil profile beneath the water main in preparation for tunneling and installation of the sewer lines. The varying soil strata presented a challenge to the project team to establish a constant set of jet grouting parameters throughout the stabilized zone while keeping within the specified unconfined compressive strength range for the stabilized zone of 690 to 1,380 kPa (100 to 200 psi)at 28 days.

Jan 1, 2003

By Michael Francis, Chris Darton

More than 55 km of tunnels have been constructed by TBM in the last 12 years to refurbish and upgrade the high voltage cable network in London. These include a tunnel of 20km length using EPBM machines in both clay and granular soils. Route selection was made with reference to subsurface structures, existing ground conditions, using suitable shaft locations addressing environmental concerns. The complex interfaces to manage included obtaining of consents to the coordination of multiple suppliers. The paper describes how all these challenges have been met successfully and how technology has been employed to provide for safe construction and operation in the congested urban environment.

Jan 1, 2003

By Duane A. Smith

They are gone now. Gone like that long ago generation that gave them birth. The Homestake Mine, nestled in the northern Black Hills, closed in 2001 after 125 years, the longest run of any major American gold mine. The Homestake Mining Co., which guided its destiny for those many years, is gone too. It merged with Barrick Gold. The Hearst family, which guided the early destiny of both, has long since gone beyond its mining heritage and into the national and even international spotlight. The mine and the company passed from the scene with as little fanfare as heralded their birth, amid the Black Hills gold rush of the 1870s. They both grew into American mining legends, as did the town they sired and nurtured, Lead. In a real sense, the mine and the company symbolized one of the last links to a vanished world and a mining era.

Jan 1, 2003

By Matthew E. Fowler, Jean Habimana, Roy F. Cook

The West Side CSO Tunnel, Pump Station & Pipeline Project is currently beginning construction along the downtown waterfront of Portland, Oregon. This4.3 meter diameter, 5,500 meter-long soft ground tunnel will be driven along the westbank of the Willamette River adjacent to buildings and utilities and several major pile-supported bridges. High groundwater pressure, extended lengths of gravel to cobble-size alluvium, and the need to control ground loss and surface settlements were key considerations in the selection of slurry tunnel boring machines for the project This paper presents an overview of the numerical modeling that was performed during design to estimate the strains and additional loads in the pile-supported structures and to assess the efficiency of proposed mitigation measures.

Jan 1, 2003