Search Documents

By Ryan Lindmark, Guoxing Gu, Zhenghe Xu, Jacob H. Masllyah

Induction time is often referred to the time required to form a stable three-phase contact between a gas bubble and a flat or droplet surface in a liquid medium. It can be used to quantify the attachment process in aflotation system. Various techniques have been developed to measure this important parameter. Due to its importance in flotation systems and other processes, significant advances in refining the induction time measurement techniques have recently been made. This paper summarizes these recent advances and describes a novel method developed to monitor bubble attachment to a pendant bitumen drop or bitumen-coated flat surface. This visualization-based method offers a higher sensitivity and accuracy than the previously developed apparatuses in the induction time measurement. As an example, the induction time for oxygen bubble-bitumen attachment was measured at a fixed bubble size as a function of temperature in two different aqueous solutions. The results showed that higher process temperature is favorable for oxygen bubble-bitumen attachment and hence bitumen flotation. Addition of calcium to the aqueous solution slightly decreased induction time.

Jan 1, 2005

By Yuemin Zhao, Daniel Tao, Xinxi Zhang, Qingru Chen, Maoming Fan, Zhenfu Luo, Xiuxiang Tao, Guohua Yang

Coal is currently cleaned with the minimum of size reduction, fine particle processing, recovery, and tailings disposal are major problems. Adequate water resources are not always available. For example, two thirds of China's coal is located in arid areas. Hence, dry separation provides an alternative approach. Of the dry coal separation methods available, air dense-medium fluidized beds have been used to separate 50~6mm coal efficiently. However, excessive bubbling and back mixing of the separated solids in the air-dense media fluidized bed causes the high lower size limit of 6mm for the feed material, this affecting the preparation efficiency. Based on prior study on air-fluidized dense media for 6~50mm coal preparation, this paper presents methods and test results on the fine coal dry classification, static electricity beneficiation of 0~0.5mm coal, and magnetically stabilized fluidized beds for separating 0.5~6mm coal.

Jan 1, 2005

By L. Maday, V. J. Perrone, M. B. Gilbert

INTRODUCTION The Brightwater conveyance system project in King County, Washington consists of constructing about 21 km (13 mile) of effluent and combined influent and effluent tunnels. The influent tunnels will collect sanitary sewerage from the service area and convey it to the new wastewater treatment plant (WTP) site at Route 9 in Woodinville, Snohomish County, Washington. The effluent tunnels will convey treated effluent from the WTP to an outfall at Puget Sound. The tunnels will be constructed primarily under residential areas, busy suburban roads and state highways. This 21 Km (13-mile) soft ground tunneling project faced many design challenges because of the geologic and hydrostatic conditions, long tunnel reaches, and large overburden depths. Boring depths typically varied from 45.7 M (150 ft) to 114 M(375 ft) with a maximum depth of 185.6 M (566 ft) deep. Conventional empirical methods for non-mountain terrain based on a 1:1 ratio of drilled footage per foot of tunnel bore (National Research Council, 1984) for evenly spaced borings provided a good start for the Phase 1 explorations. However a continuation of this approach with closer spacing was deemed inadequate by the geotechnical team for efficiently allocating geotechnical exploration resources for the final design. This paper presents a rational approach that was used to evaluate the value of a particular geotechnical exploration boring, pump test or other in-situ test. The method of analysis, which was initially developed for rock tunnels (Einstein et al., 1978), was modified for the Brightwater project. The method considers the potential construction cost risks resulting from variable geologic conditions, the cost and reliability of the geotechnical exploration and the earned value (cost risk reduction) of performing the geotechnical exploration. PROJECT DESCRIPTION In total the land portion of the conveyance system will include approximately21 Km (13 miles) of tunnels ranging in size from 3.0 to 5.2 M (10 to 17 ft) minimum inside diameter with overburden depths of 30.0 to 168 M (100 to 550 ft) and

Jan 1, 2005

By G. Barrasso, E. Nordheim

"The European aluminium industry, through its member organisation the European Aluminium Association (EAA), initiated a program on sustainable development for the aluminium industry in 2001. The first step involved the development of a set of sustainable development (SD) indicators for the industry, taking into account of the different interests involved and also the different existing conventions. The indicator set was developed during 2001 and 2002 with the assistance of recognised partners, including Wuppertal Institute from Germany and Versailles University from France. As well, both internal and external stakeholder groups were involved in order to validate the indicators. This has resulted in a set of thirty-four indicators used in the first survey exercise. In the survey the EAA, together with the national aluminium associations, attempted to cover all European plants producing alumina, primary aluminium, rolling ingots, extrusion ingots, foil and recycled aluminium -covering approximately 800 plants. The survey used two points in time, 1997 and 2002, in order to start developing a trend for the individual indicators and to measure progress over time. The industry response to the survey was very positive, with a total industry coverage based on tonnage reported of over 80% for 2002 data and 70% for 1997 data. The results also show a solid progress for most indicators and particularly for social indicators such as training performance, community involvement and employees health programmes. The EAA is committed to conducting this as a regular exercise and is engaged in a number of stakeholder workshops in order to present the survey results, to review the indicators used and to also consider adjustments of these based on feedback from stakeholders and experiences from the first data collection."

Jan 1, 2005

By E. Sarris

Tailings dams are large-scale earth-fill embankments that are designed to contain mining wastes from ore dressing plants. Most commonly tailings dams are constructed in stages in order to keep up with the increasing volume of mine tailings. Staged construction using various methods (like up-stream, down-stream, and centerline) is generally considered as a very effective way to construct this kind of embankments. The present study is devoted to the investigation of the behavior and the stability of these geostructures under static conditions. In order to accomplish this task, elaborate two-dimensional numerical models are examined, utilizing the geotechnical finite-element code PLAXIS. Numerical analyses are conducted for all three types of tailings dams in order to obtain the potential modes of failure, while the corresponding factors of safety are determined by the shear strength reduction technique.

Jan 1, 2005

By C. Stoneback

The attapulgite industry saw a year of solid growth after a weaker 2003. Demand was up between 5 percent and 6 percent driven by almost all of the key markets. Construction continued to show record new housing demand, assisted by continued low interest rates. That drove strong growth in construction related markets like coatings, tape joint compounds and other construction materials applications. The agricultural markets rebounded modestly to increase sales for suspension fertilizers, animal feeds and pesticide carriers. Oil drilling also showed strong growth due to high oil and gas prices. Sales to molecular sieve applications grew due to petrochemical and construction demand. The export markets were assisted by further depreciation of the dollar. The only weak area was in nonagricultural granular sorbents, where other sorbent materials continued to dominate.

Jan 1, 2005

By S. Solar, G. Tiess, K. Nielsen, H. Wagner

The paper summarises the results of a recent study of minerals planning policies of the Member States of the EU. The study has shown that contrary to the public opinion the production of industrial minerals and construction minerals is significant the former accounting for about 20 percent of global production, the latter amounting to about 3 billion tonnes per annum. In contrast the importance of metal ores has diminished although metal production in some European countries can still be significant. The study revealed that very few Member States have clearly defined mineral policies. Common to most mineral policies is the emphasis on reducing minerals consumption and recycling whereas the important aspect protecting access to minerals resources is not adequately addressed by most policies. Access to mineral deposits is regulated in most Member States by land use legislation and administration. Information on mineral deposits in land use planning data bases tends to be scarce. This together with the absence of formal mineral policies places minerals at a disadvantage in land use decision making. The emergence in the recent past of environmental legislation and in particular environmental impact assessments has had a crucial effect on the duration of the authorization process for new mineral projects. Examples are given how minerals planning is handled in some of the Member States.

Jan 1, 2005

By Bruno Bussière, Michel Aubertin, Anne-Marie Dagenais, Johanne Cyr

A five steps remediation program was commissioned in 1998 for the acid generating Lorraine mine site, located in the Témiscamingue region, Quebec, Canada. It included, as the main expenditure, a cover with capillary barrier effects (CCBE) used to limit oxygen migration. After construction of the cover, instruments were installed on site to monitor the CCBE performance. Modified oxygen consumption tests were also done to measure the oxygen flux through the cover. Results from water content and suction data, measured from 1999 to 2003, show that the capillary barriers effects are effective and that the water retention layer stays near saturation throughout the years. Oxygen fluxes estimated from monthly water content measures are generally below 10 g/m2/year. Results from modified oxygen consumption tests made on the site give almost similar oxygen fluxes. A two dimension numerical model of the Lorraine mine site was also constructed to verify that mathematical models could predict realistically the in situ conditions on such a large scale site. Numerical results obtained for three years show a good concordance between measured and calculated values. The results obtained form these different evaluation methods for the performance of a CCBE concur and confirm the efficiency of this cover in limiting acid mine generation.

Jan 1, 2005

By Augustine O. Orumwense

Ball mills are commonly used for regrinding operations in the mineral processing industry. But, in recent times, efforts are being made at the introduction of stirred mills particularly for those instances where very fine grinding is required. Media type (steel shot, glass beads, alumina balls and crushed quartz), media size, mill speed and the number of passes required to obtained the target product size are studied. The product size and energy consumption are used in the evaluation of the test results. The grinding media size, shape, density, filling ratio, mill circumferential speed and grinding time play a distinct role in product size fineness.

Jan 1, 2005

By Charles Merguerian

In medium- to high-grade metamorphic terrains such as found in New York City(NYC), rock mass texture and mineralogy are important factors in predicting TBM penetration destiny. Integration of data from over two decades of traditional field and tunnel mapping suggest that hard-rock TBM penetration in the NYC area depends upon textural, mineralogic, and structural control. The bedrock of NYC consists of many different lithologic units of varying age, composition, texture, and metamorphic grade including many varieties of intrusive rock. In addition, brittle faults of numerous orientations cut the polydeformed crystalline bedrock, producing zones of highly fractured and disturbed ground and high water inflows. Pre-bid compilation of published bedrock data, drill core analysis by geologists to establish lithologic and mineralogic trends, integrated surface geologic mapping along a proposed alignment, and targeted petrographic and geotechnical investigations to characterize the rock mass conditions together constitute an important prelude to successful subsurface bidding and tunneling. A carefully planned program of as-built geological mapping, structural analysis, fracture class mapping, and monitoring of machine performance data provide important information for adjusting to changed conditions. In complex terrains, a clear understanding of the structural geology of any proposed tunnel line is the simplest and most cost-effective method to mitigate losses encountered during TBM tunneling.

Jan 1, 2005

By K. Häge

"Die Nachhaltigkeit der Braunkohlengewinnung in der öffentlichen Wahrnehmung wird nur weiter erfolgreich kommuniziert werden können, wenn durch konkretes Handeln glaubhaft gezeigt wird, dass die offenen Fragen fair und solide beantwortet werden. Dazu gehören insbesondere die neue innovative technische Lösung sowie das sensible Interessenmanagement. Die Braunkohlenindustrie hat gelernt, dass Offenheit und nicht zuletzt das beständige Bemühen um den Meinungsaustausch mit ihrem Umfeld wichtige Elemente sind. Der in Jahrzehnten erworbene Schatz an Glaubwürdig-keit ist eine Basis, auf der die Braunkohlenindustrie ihre Zukunft gestalten kann. Darüber hinaus sind politische Rahmenvorgaben erforderlich. Das öffentliche Interesse an einer sicheren und preiswerten Energieversorgung unter Einschluss der Braunkohle ist unverzichtbar. In diesem Kon-text kann dann die Braunkohle die an sie gerichteten Fragen der Ökonomie, der Ökologie und der Sozialverträglichkeit auch mit Hilfe von Indikatoren beantworten.ABSTRACTThe discussion of the sustainability of lignite mining can only be continued successfully if the indus-try acts in a practical manner and demonstrates trustworthiness by responding fairly and reliably to open questions. This includes new and innovative technical solutions as well as the sensitive management of interests. The lignite industry has learned that openness and the constant effort to exchange viewpoints within their environment are all essential elements. The credibility that has been gained over the decades is the foundation on which the lignite industry can build its future. Beyond that a framework of political guidelines is necessary. Public interest in a secure and inex-pensive energy supply that also includes lignite is indispensable. In this context, the lignite industry will then be able to answer the questions which are directed at them and concern the economy, ecology, and social tolerability also by indicators."

Jan 1, 2005

By Paul M. Godlewski, Joseph P. Gildner, David S. McAllister

With construction underway on the 22.5 km (14 mile) Initial Segment of the Link Light Rail transit system in Seattle (including the one-mile EPB-driven running tunnels and mined station at Beacon Hill), the Sound Transit Board on May 20, 2004 voted on selection of a preferred route for an approximately eight-mile extension northwards from the central business district to Northgate, and authorized immediate start of advanced conceptual/preliminary engineering and geotechnical exploration programs scheduled to be completed in Spring 2005. The extension includes approximately914 m (30,000) route-feet of bored running tunnels, a mined station with platform level approximately 60 m (200 ft) below grade, three (possibly four) cut-and-cover stations and a cut-and-cover cross-over structure, as well as an aerial terminal station at Northgate and other line-section below-grade and aerial structures. All tunneling will be in glacial soils.

Jan 1, 2005

By D. A. Kramer

Ammonia, the principal source of fixed nitrogen, was produced by 16 companies at 31 plants in the United States during 2003. Fifty-five percent of U.S. ammonia production capacity was centered in Louisiana, Oklahoma and Texas because of their large reserves of natural gas, the dominant domestic feedstock. Production In 2004, U.S. producers operated at about 59 percent of their rated capacity. The United States remained the world’s second largest ammonia producer and consumer following China. Urea, ammonium nitrate, ammonium phosphates, nitric acid and ammonium sulfate were the major derivatives of ammonia in the United States, in descending order of importance.

Jan 1, 2005

By J. D. Miller, C. L. Lin

In the processing industries, it is well known that particle shape is an important factor which determines the behavior of particulate systems. For example, system properties of technological significance including rheology, suspension stability, agglomeration, packing, permeability…etc, are affected by particle shape. In this regard, characterization and analysis of particle shape is essential for more detailed understanding and improved development of particulate processes. In general, it is clear that the behavior of these systems depends on the statistical characteristics of particle shape. Remarkably few techniques exist to predict the mechanical and hydrodynamic behavior of an irregularly shaped particle or a population of irregularly shaped particles for that matter. The lack of models and correlations can be attributed to the wide variety and complexity of particle shapes, the difficulty of defining shape descriptors suitable for modeling, the limitations of measuring shape, and the lack of classifying techniques to characterize particle shape. In this paper, we present information on how 3D particle shape can be measured, characterized, and analyzed using cone-beam X-ray microtomography (XMT).

Jan 1, 2005

By Mohammad Irshad, Klaus Mussger, Harald Wagner

Despite the fact that the New Austrian Tunneling Method; NATM, has been used in the United States for the past 23 years or so, still considerable misconceptions exist in the industry about the nature of the method and its implementation. In the authors’ view its implications are usually not well understood. The paper provides an overview of the highlights of NATM usage over the past two decades to illustrate the point that NATM is now a well-established tunneling method in the U.S.A. Accordingly the thrust of this paper is on the more pragmatic aspects of the NATM technology usage as it concerns the Owners, Designers and the Contractors. Prior to examining the implications of NATM usage from the viewpoints of various stakeholders, it should be helpful to first briefly provide an overview of the history of the method as it was introduced and implemented on several key tunneling projects in the US, over the last 2 plus decades.

Jan 1, 2005

By T. H. Eyde

Estimated natural zeolite production worldwide during 2004 remained at about 3.6 Mt (4 million st), about the same as in 2003. China continues to be the largest producer of natural zeolites followed by Cuba, Germany, Japan and South Korea. This may be changing, however. Since 1988, zeolite production from Australia, Indonesia, Malaysia, New Zealand, Philippines and Thailand has increased rapidly. Most of the production is consumed in aqua culture. Global demand for seafood has exceeded the ability of the oceans to supply it without over fishing. Zeolite minerals remove ammonia compounds from the ponds in which fish and shrimp are grown. It is estimated that, in Thailand and Indonesia more than 55,000 farms produce260 kt (286,500 st) of shrimp. Therefore, as shrimp production increases, so does zeolite consumption.

Jan 1, 2005

By Greg Adel, Darren Thornton, Julius Krutschnitt, Toni Kojovic, J. Mark Richardson, Bryan Smith

Mine-to-Mill® optimization is a total systems approach to the reduction of energy and cost in mining and mineral processing operations. Developed at the Julius Krutschnitt Mineral Research Centre in Queensland, Australia, it attempts to minimize energy consumption through the optimization of all steps in the size reduction process. The approach involves sampling and modeling of blasting and processing, followed by computer simulation to optimize the operation and develop alternatives. The most promising alternatives are implemented, and sampling is conducted to quantify energy savings. In the current DOE-sponsored research project, the primary objective is to adapt the Mine-to-Mill® technology to the aggregates industry. The project is being carried out at two quarries operated by Luck Stone of Richmond, Virginia. This paper presents work conducted at the Bealeton quarry.

Jan 1, 2005

By M. Galetakis, C. Roumpos

A sustainable coal industry needs to achieve a number objectives concerning mainly with superior utilisation of deposits and improved environmental performance. Modern quality control systems, which are greatly based on the on-line analysers, play an important role in achieving sustainability targets. This paper discusses the testing and application of on-line ash analysers installed in the Ptolemais and Megalopolis lignite mines in Greece and examines the possibility of using this type of analyser to control blending and homogenisation operations. The effect of the accuracy of on-line analyser to control process, when used for the characterization of low rank coals with complex and variable composition, such as greek lignites, is examined.

Jan 1, 2005

By I. Papadopoulos

Nowadays, geophysical prospecting is implemented in order to resolve a diversity of geological, hydrogeological and geotechnical problems. Though plenty of applications and a lot of research have been conducted in the country-side, only a few have been reported in the literature concerning urban areas, mainly due to high levels of noise present that aggravate most of the geophysical methods (e.g. electromagnetic, seismic, gravity etc.) or due to spatial limitations that hinder normal method implementation (e.g. electrical). Among all geophysical methods, electrical tomography proves to be the most rapid and urban noise insusceptible technique. This work presents a case study in the urban area of Hania (Crete I., Greece), where Electrical Resistivity Tomographies (ERTs) have been carried out for the detection and identification of possible buried ancient ruins or other manmade structures, prior the foundation of a building. Nineteen profiles were surveyed in a 20x40m grid using dipole-dipole configuration. The results indicate two areas of interest, that are interpreted as probable old wells, in the context of the existence, in former times and in the same area, of an olive oil plant. In the vicinity, near surface ancient ruins have been disclosed, but no such evidence provided this survey, for the particular area under study and the prospected depth. The collected ERT-data were processed by applying advanced algorithms in order to obtain a 3D-model of the study area that depicts more clearly and accurately the interesting subsurface structures.

Jan 1, 2005

By Liguang Wang, Roe-Hoan Yoon

The thin film balance (TFB) technique was used to measure the equilibrium film thicknesses (H3 between two air bubbles in sodium dodecyl sulfate (SDS) and electrolyte (NaCl) solutions. The results were used to determine the magnitudes of the hydrophobic forces (K232) using the extended DLVO theory. The Km values determined from He measurement allowed us to predict disjoining pressure isotherms, which were found to be in excellent agreement with those obtained experimentally using a bike-wheel film holder. The rate of film thinning was measured at low SDS concentrations with varying amounts of electrolyte (NaCl) added. In general film thinning was controlled by the capillary pressure during the initial stages, while it was controlled by the surfaces forces during the later stages. At low NaCl concentrations, it was possible to predict the rate of film thinning using the Reynolds equation, provided that the driving force was corrected for the contributions from the hydrophobic force, which in turn were determined from the KZ32 values obtained from the He values measured experimentally. At high NaCl concentrations, where it was difficult to measure the equilibrium film thicknesses, the contributions from the hydrophobic forces were determined by fitting the film thinning data to the Reynolds equation. The K232 values obtained using both the equilibrium film thickness and the film thinning measurements showed that hydrophobic force deceased with increasing surfactant and salt concentrations. It was found that the hydrophobic force in foam films was very sensitive to the added electrolyte concentration.

Jan 1, 2005