Search Documents

By M. Karmis

The design of coal-mine layouts is based on the knowledge of a broad range of geological and geotechnical parameters, which must be determined from a sequence of exploration programs. It follows that any weaknesses in selecting, determining, interpreting or utilizing these data are inevitably reflected into the mine-planning process. In this paper, the main methods of exploration are reviewed and evaluated with the emphasis on acquisition, interpretation and storage of variables pertaining to mine-design. Some common problems are highlighted and recommendations are given for improving the utilization of data and optimizing coal-mine design procedures.

Jan 1, 1980

By Richard Dunmore

Most coal seams in the United Kingdom contain firedamp, some of which is released into the ventilating airways as the strata around a working relax. The close sequence of seams in carboniferous strata is usually such that seams in adjacent roof and floor strata are also disturbed and potentially large quantities of firedamp can enter the workings from these sources. Since emission depends on the disturbance rate of the seams, higher coal production rates associated with increased mechanisation in the colliery accentuate the problem. Firedamp concentrations in UK underground workings are subject to statutory regulations1. To enable production to continue uninterrupted and in safety the problem is tackled by ventilation engineers by the provision of adequate ventilation in the airway and by the technique of firedamp drainage. In the UK the latter usually takes the form of cross-measure boreholes in roof strata, and increasingly also in floor strata, drilled from the gateroads, especially from return airways. In this way firedamp emitted from disturbed seams in adjacent strata can be extracted directly to the surface or to some safe position outbye, and the airways of the working district are not contaminated. Despite the use of firedamp drainage, considerable quantities of firedamp enter the ventilation air- stream and the concentration levels may be seen to be related to the coal production activites in the district. Figure 1 shows a typical recording of methane concentration obtained by a BM1 methanometer at a position outbye in a return gate where firedamp drainage was operating. The general rise in level throughout the working week may be seen, together with peaks occurring during production shifts and the gradual decay of emission over the weekend. In view of the fact that ventilation and firedamp drainage contribute a considerable proportion to the operating costs of the colliery, it is essential that the ventilation and firedamp drainage requirements be calculated as accurately as possible at the planning stage of the working. In the past the ventilation engineer has had to rely heavily on experience in neighbouring workings but with the development of mines in previously unworked areas there is clearly a need for a methodical approach to meet the requirements of planning. The work described in this paper represents such an approach and it is hoped that successful development and application of the method of prediction will lead to the widespread adoption of a routine procedure. The current development of a method of prediction of firedamp emission into longwall workings is based on the theoretical treatment of gas emission from coal seams proposed by Airey2 in 1971, which was based on his study of gas emission from broken coal 3 which was published in 1968. In common with other experimental methods of prediction, the method enables a calculation to be made of the total make of gas emitted from all sources of gas in the strata per tonne of mined coal.

Jan 1, 1980

By J. W. Lowry

After years of processing copper porphry ores, the Ray concentrator of Kennecott Minerals Company installed a concentrate regrind mill in its flotation circuit. The first cleaner concentrate is reground rather than the usual rougher concentrate. An additional cleaning of the reground product yields an increase in copper content of the final concentrate and a significantly lower insol content. The desired goal of decreasing the energy requirements for smelting the concentrate has been achieved.

Jan 1, 1980

By R. F. Davis

The evaluation and selection of coals for producing metallurgical coke is indeed a com- plex process simply because coal is a complex and variable substance which is sensitive to how it is treated from the time it is mined until it is transformed into coke. A review of the the more common evaluation tests made on coal and how the test results are applied in commercial practice. Parameters used to select coal blends for wet and preheated charges should also be of interest.

Jan 1, 1980

By J. C. Motz

The advantages of producing a fine mill feed have been recognized for many years. The extent to which fine crushing can be carried out will vary and depends on the ore characteristics, plant and crusher design. Unfortunately, the ore characteristics are generally beyond our control, so the concentration of effort lies primarily on the plant arrangement, equipment design and operation Where fine crushing should stop and grinding begin is controversial and is influenced greatly by personal opinions and experiences. Often, this break point will be different if consideration is being given to a new plant in comparison to a modest expansion. Most new plant designs employ the largest and most efficient equipment. The modification of existing plants becomes more complex because of the space requirements and the related equipment already in operation. Fine crushing is, of course, a relative term. Obtaining a final crusher product of minus 3/4" is commonplace today and can occasionally be obtained in an open circuit final crushing stage.

Jan 1, 1980

By T. P. Harrington

Research efforts are just beginning to identify the acoustic signatures of very short pulses of sound associated with the fracture of single particles in an autogenous mill. This presentation will discuss the anticipated correlation between these data and the fundamental mechanisms of rock fracture It is hoped that further tests will help identify what design and operating parameters influence the acoustic spectra, determine whether different minerals have different spectra and correlate product particle size distribution with acoustic spectra.

Jan 1, 1980

By J. W. Gunnett

Abstract. The Surface Mining Control and Reclamation Act of 1977 (PL-95-87), Section 522, establishes requirements for state regulatory authorities to designate lands unsuitable for all or certain types of surface coal mining. Any party having an interest in an area that may be affected can petition for it to be designated unsuitable for mining. Section 522 could present major obstacles to the mining industry by typing up an area in an endless round of petitions. The program under development for Kentucky is examined and analyzed as an example for determining the hidden impacts of Section 522.

Jan 1, 1980

By F. Palmay, R. D. Gwilym, P. Eng

INTRODUCTION As the experience in Canada indicates, it is becoming more and more common to evaluate major mining projects, especially those relating to uranium, with respect to their environmental effects. As part of this evaluation public hearings are becoming the rule rather than the exception. In this area the 1970's and presumably the 1980's can be characterized as the age of "Environmental Assessments" or "Environmental Impact Statements" which form the basis of these hearings. These documents tend to require significant amounts of research, data collection and effort in their preparation, and tend to be closely scrutinized by the hearing body and by groups in opposition to the project. This opposition is becoming more organized and sophisticated. The assessment or impact document, together with the evidence supporting it during the hearings can: (a) mean the difference between a lengthy and hence costly hearing and a smoother, shorter and less expensive one, (b) result in requirements for extensive modification at the expense of the proponent to his project, (c) result in the proponent being required to carry out extensive studies, research or monitoring programs, and (d) conceivably may in certain situations result in the project actually being turned down. Therefore, while on the one hand it is important to have available technical answers to concerns relating to uranium, its associated and perceived hazards, it is getting more and more important to be able to present these answers in both a written and oral format in such a way as to meet the criticism and concerns of the opposition, be they citizens in general or special interest groups including environmental lobbyists. JURISDICTION From a Canadian perspective, the first legal question to be answered is which level of government has jurisdiction over uranium mines in general and specifically over aspects relating to the environmental effects, including the health and safety aspects, of uranium mines and

Jan 1, 1980

By E. D. Stephenson

As part of the British Steel Corporation?s development plan during the 1970?s, it was decided to concentrate its bulk steelmaking processes based on the BOS at 4 major Works with access to deepwater ore terminals, for the supply of high-grade imported ores. These 4 sites were at: - 1. Rarenscraig Works in Scotland where the ore terminal would be hilt at Hunterston on the west coast some 50 miles away. Bavenscraig was already an integrated Works but suffered from having to discharge ore 27 Glasgow tenxinus on the River Clyde, which could only accommodate vessels up to 25,000 tonnes. In the future, ore was to be unloaded at Runterston and shipped by a rail-link into Ravenscraig, The new ore terminal would have the potential to unload vessels up to 300,000 tonnes. - 2. Port Talbot Works in south Vales where the existing harbour was developed to discharge large ore carriers. This again was an existing Integrated Works and the benefits of the new harbour also applied to Llanwern Works which was another integrated Works some 50 dies to the east, which would now receive ore from Port Talbot.

Jan 1, 1980

By Clifford B. Farris

Introduction Shale Mining Problems The mining problems an oil shale operator will face are largely determined by the process. Candidate oil recovery processes are surface (above ground processing of mined oil shale), modified in situ (underground with some shale removed), and true in situ (completely underground with no shale removed). The shale removed for modified in situ (MIS) is generally processed by surface techniques. The mining problems are different for each category. Fig. 1 depicts the diversity of western shale deposits. Mining for surface operations will employ underground mining techniques in common use but the scale will be larger. A typical oil shale operation is expected to require 75,000 to 250,000 st (68 000 to 226 800 tons) a stream day of crushed oil shale. This is above the upper limit of current mining operations. Major problems in¬clude: (1) lack of good engineering design properties for oil shale, especially when interbedded with saline minerals at depths below 1,000 ft (305 m); (2) presence of water, hydrogen sulfide, and methane in some areas; (3) necessity for mine disposal of as much retorted oil shale waste as possible; and (4) control of en¬vironmental impacts of mining. Portions of the oil shale deposits in Colorado, Wyoming, and Utah and significant portions of the Devonian shales in the eastern U.S. are adapted to surface mining. No major technological problems are apparent outside overburden thicknesses up to 1,000 ft in the West. However, numerous political and environmental dif¬ficulties have arisen. One major oil shale developer cancelled a planned surface mining operation and currently is pursuing a modified in-situ plan. The eastern shales are closer to the surface than the western, but suffer from many of the same environmental and political problems. Modified in-situ operations face much more severe mining problems than surface efforts. Because the mined stope (called an in-situ "retort" by processors) acts as a retorting process vessel subject to gas flow, combustion, and temperatures between 1,500° and 2,000°F, mining is under highly restrictive limitations. This processing method involves removing between 20 and 40% of the shale deposit and then blasting the roof and walls into the mined space, where the oil is recovered by retorting. Major problems are: (1) swell factor severely limited; (2) need for consistent size distribution of blasted shale; (3) even filling of stope (in-situ retort) by blasted shale with consistent permeability throughout; (4) scaleup of blasting techniques, after optimization; (5) protection of retort pillars and roof during and after retorting; (6) prevention of groundwater percolation; (7)use of ANFO explosive in wet holes; (8) disposing of surface-retorted shale waste in stope; and (9) restoration of site. True in-situ operations are less well developed than surface or MIS processes. No actual mining is done, as the true in-situ processes generate permeability in the highly

Jan 1, 1980

By George Innes

The soda ash business in the United States has undergone a sweeping technological change in ihe last 20 years. In a world where synthetics are continuzlly replacing natural products, here we have exactly the opposite, a syntheric chemical being replaced by a natural product. This change is nearly complete in the U.S. and is beginning to take place in Europe and other parts of the world.

Jan 1, 1980

By D. Raicevic

The presence of residual uranium and other radionuclides in the uranium mill tailings are posing a continuous health concern to the surrounding environment. The slow generation of sulphuric acid from residual sulphide minerals is the cause of persistant dissolution and discharge of many metallic components of the tailings. The most effective long term solution to these problems would seem to be to produce chemically stable tailings. This paper describes two possible answers to the objective: (1) Removal of radionuclides and pyrite from tailings by mineral dressing techniques; some 60 - 68% of the residual uranium, 70 - 75% of the radium, 60 - 65% of the thorium and 95 - 98% of the pyrite have been rejected from the Elliot Lake tailings. The decontaminated tailings contained 0.003% uranium, 50 - 60 pCi/g radium226, 0.01% thorium and less than 0.1% sulphur as pyrite. (2) Preconcentration of radionuclides and pyrite by beneficiation from Elliot Lake ores prior to leaching; applying this approach about 97% of the uranium, 95% of the radium, 92% of the thorium and 98.5% of the sulphides were concentrated in a radionuclide and pyrite concentrates comprising 25% and 8% of the ore, respectively. The preconcentration tailings (waste) produced contained 0.004% uranium, 20 - 25 pCi/g radium226, 0.005% thorium and less than 0.1% sulphur as pyrite. Economic and environmental advantages of both approaches and the leaching of the concentrates are also discussed.

Jan 1, 1980

By B. Zane Egan

The Calsinter process for recovery from fly ash involves sintering the fly ash with calcium sulfate and calcium carbonate at 1200°C, followed by a dilute sulfuric acid leach step. Flue gas desulfurization sludge containing calcium sulfite, calcium sulfate, and unreacted calcium carbonate may be substituted for the calcium sulfate and calcium carbonate. Conversion of aluminum in fly ash by the sintering process to an acid-leachable species was measured as a function of sintering time and temperature in the range of 800°-1200°C The sinter-leach steps were investigated using thermogravimetric analysis, x-ray diffraction, scanning electron microscopy, and elemental analysis. SEM photographs indicated that the glassy spheroids in the original fly ash were converted to a crystalline structure by the sintering reaction.

Jan 1, 1980

By Patrick Linehan

Vibration and air blast noise from blasting were evaluated during a research program which was sponsored by the U. S. Bureau of Mines. Blast variables were studied using small scale model (SCM) tests to evaluate specific variables as well as interactive effects, followed by experiments with production blasts at the surface coal mines. Experimental data showed that the primary variables affecting the ground vibration amplitude are the charge weight per delay and the length of the delay interval. Blast variables having a significant effect on the overpressure amplitude include the charge weight per delay, the length of the delay, burden and spacing, stemming amount and type, direction of initiation, charge depth and amount of detonating cord and cover.

Jan 1, 1980

By H. Weber

This paper is in three parts. Part I discusses the various types of cement clinker coolers now in full-scale operation. Part II is a detailed study of the criteria for selection of the type of cement clinker cooler best suited for a given installation. Part III covers a number of cooling problems and their solutions in some of the metals industries. The large and world-wide problem of cement clinker cooling has motivated much study and development and the coverage here of this work is somewhat detailed. In contrast the cooling problems of the metals industries are quite varied between industries and often quite different from plant to plant in the same industry because of basic differences in the requirements of the particular material being processed. Therefore the coverage of metals industries coolers is somewhat more general. It is believed that all of the technology covered here may be of interest to those working with the problems of cooling hot materials.

Jan 1, 1980

By Harlan N. Barton

A commercially available portable X-ray spectrograph, lightweight and of rugged construction for vehicle or field camp use, was used for the determination of Ba, Cu, Fe, Mn, Pb, Rb, Sr, and Zn in stream sediment geo- chemical samples. Investigations showed a relative standard deviation of 1-3 percent, detection limits of approximately 100 ppm; and significant matrix effects. Coefficients of correlation greater than 0.9 were obtained between portable X-ray and emission and atomic- absorption spectroscopy analyses. A geochemical map of a known mineralized area showed good agreement with maps prepared by other methods of analysis and sample media.

Jan 1, 1980

By C. G. Clifton

The Oatman District produced approximately 2.2 x 10 6 ounces of gold and 0.8 x 10 ounces of silver between 1897 and 1942. A total of 3.8 x 10 tons of ore averaging 0.58 O/T gold and 0.17 O/T silver was extracted from eight major orebodies and a number of lesser deposits. Oatman lies at the center of a trachyte-latite-rhyolite volcanic complex which contains at least one resurgent caldera. The orebodies are typical epithermal quartz-calcite + adularia lode deposits which are very deficient in sulfur. Ore deposition has occurred within dilatant zones on faults which radiate from a common point within-the complex. Fischer-Watt Mining approached the Oatman District with an integrated exploration program utilizing four basic procedures to define the characteristics of past productive areas the results of which were applied to unexplored portions of the vein system. These procedures, listed in their order of usefulness, in defining known and prospective mineralized zones are: vein contouring, detailed alteration mapping, fluid inclusion temperature determinations, and geochemical sampling.

Jan 1, 1980

By Dennis P. Bryan

Nevada is especially well endowed with industrial minerals, both in the number of ore deposits and the diversity of commodities. More than 600 significant industrial mineral deposits, containing 22 principal commodities, are present, in the State. The materials produced in Nevada in 1978 had a value of approximately 113 million dollars, and additional processing of some of them (e.g. gypsum into wallboard, limestone and clay into cement) added considerable more value. Table 1 shows the value of Nevada's industrial mineral production in 1978. Nevada currently supplies 85 percent of the country's barite producing 1.6 million tonnes (1.8 million short tons) valued at 30 million dollars in 1978. Nevada is second in diatomite production and contributes one-third of total lithium produced. Other industrial minerals being produced include clays, fluorspar, gypsum, lightweight aggregates, limestone and dolomite, magnesite and brucite, perlite, salt, sand and gravel, and silica. In general, Nevada produces high-value industrial minerals which are not consumed within the State, but rather, are shipped out of State. In contrast, most more populous states produce larger tonnages of lower value industrial minerals which are consumed chiefly within that state.

Jan 1, 1980

By T. V. Johnson

The microstructural relationships in dolomitic fluxed taconite pellets were studied. The influence of basicity (in the range 0.75 to 2.1) and firing temperature (to 1340°C) on the grain structure, macrostructure, and mineralogical phase relationships are described. Extensive slag bonding of hematite grains begins at temperatures between 1220 and 1230°C, and results in fundamental changes in grain structure. Successive temperature increases result in little change in grain structure until 1340°C, when extensive coalescence of the hematite grains begins.' Increasing flux additions have little effect on grain structure but greatly influence pore character. The compressive strength decreases with increasing flux addition, increases with increasing firing temperature, and is related to the macrostructure of the pellet. The compositions of the slag phases are represented on the CaO-Fe2O3-SiO2 phase diagram, and the compositional path of slag development is described.

Jan 1, 1980

By Ing. Ludwig Schlebusch

The significant growth of the world population and its demand for an increasing standard of living leaves no other choice than continuously augmenting industrial production and making available steadily greater quantities of raw materials at still better qualities. Therefore, any raw material has to be utilized to the greatest possible extent and processed at optimum economy on large mechanical equipment. The layout of processing facilities of large throughput rates can be based on multiple or single lines. The latter enables the application of large machines of optimum size. Proven equipment for homogenizing, classifying, separating superfine material, sorting and dewatering are-now available in optimum sizes. By the use of these large machines operating cost of pit coal preparation plant can be significantly lowered by reducing the specific requirements regarding space, capital investment, energy, operation and maintenance.

Jan 1, 1980