Search Documents

By J. L. Whitlock

A mutant strain of Pseudomonas paucimobilis is utilized to effectively degrade and or remove 90-98% of cyanide, thiocyanate, toxic heavy metals and ammonia from a cyanidation mill process and mine discharge maximum of 21,000 m3/d (5.5 MGD). Homestake Mining Company?s biological wastewater treatment plant has been in full scale operation for over 2 years at the Homestake Mine in Lead, South Dakota.

Jan 1, 1987

By Bruno Bussière, Michel Aubertin, Anne-Marie Dagenais, Johanne Cyr

A five steps remediation program was commissioned in 1998 for the acid generating Lorraine mine site, located in the Témiscamingue region, Quebec, Canada. It included, as the main expenditure, a cover with capillary barrier effects (CCBE) used to limit oxygen migration. After construction of the cover, instruments were installed on site to monitor the CCBE performance. Modified oxygen consumption tests were also done to measure the oxygen flux through the cover. Results from water content and suction data, measured from 1999 to 2003, show that the capillary barriers effects are effective and that the water retention layer stays near saturation throughout the years. Oxygen fluxes estimated from monthly water content measures are generally below 10 g/m2/year. Results from modified oxygen consumption tests made on the site give almost similar oxygen fluxes. A two dimension numerical model of the Lorraine mine site was also constructed to verify that mathematical models could predict realistically the in situ conditions on such a large scale site. Numerical results obtained for three years show a good concordance between measured and calculated values. The results obtained form these different evaluation methods for the performance of a CCBE concur and confirm the efficiency of this cover in limiting acid mine generation.

Jan 1, 2005

By P. W. King

The performance of the versatile McNally Wedag horizontal vibratory centrifuge for dewatering ultra fine 0.5 x 0.15 mm (28 x 100 mesh) material has proven to be success¬ful and the results presented herein will examine its capabilities in terms of capacity, solids capture, product moisture, effluent solids, and size analysis. Centrifugal dewatering of fine refuse has proven t to be another application for which this unit has performed exceptionally well.

Jan 1, 1985

By Stephanie Singarayer, Damodara Reddy Chinnasane, Mike Yao, Danielle Pelletier

Mining at Vale’s Creighton Mine has been active for nearly 120 years in Sudbury, Ontario, Canada. Being the deepest mine in the Sudbury region, mining induced seismicity is a common occurrence at Creighton Mine. Over the past five years, 26 large magnitude seismic events ranging from 2.5 Mn to 3.7 Mn (Nuttli) have occurred. Out of these large magnitude events, three 3.0+ Mn events occurred between April 2020 and January 2021. The majority of the 3.0+ Mn events are believed to be the fault-slip type that could be linked to the known major geological structures and/or long-term effect of mining over many years. The recent large magnitude events are believed to be triggered by high induced stresses while mining the first few stopes of a new lower horizon in the top-down centre out mining sequence.

Apr 26, 2022

By Todd Clarke, Ralf Winterberg

For more than a decade the tunneling industry has explored the potential and benefits of macro synthetic fiber (MSF) reinforced concrete solutions for precast tunnel segments. Parallel to industry investigations, academic research is being undertaken to better understand this material when subjected to the typical loads expected during mechanized tunneling. This paper investigates the performance of MSF reinforced precast concrete tunnel segments by means of an experimental program comprising testing of full-scale tunnel segments. The presentation of the satisfactory results of the experimental testing regime will be complemented by a brief case history from a successfully executed project—an America’s First.

Jun 13, 2021

By Ulrich Maidl, Marc Comulada, Janosch Stascheit

"INTRODUCTION Cohesive soils are notorious for causing clogging of the cutter head and the excavation chamber of tunnel boring machines (TBMs). While clogging leads to a drastic reduction in excavation performance, it further induces higher wear of tools and other parts of the cutter head and may even prevent a controlled support of the tunnel face and, thus, lead to face collapse and excess settlements or sinkholes. Employing well-balanced soil conditioning techniques, the clogging tendency can be significantly reduced. The monitoring and control of soil conditioning as well as the timely detection of potential clogging tendencies require a close monitoring of all relevant machine parameters and measurements. To this end, a reliable and powerful Process Controlling software that gathers all machine and process-related information is a prerequisite for successful mitigation of clogging-induced problems. The remainder of this contribution is organized as follows: First, a brief introduction to the Process Controlling system PROCON is given. Afterwards, the mechanisms and mitigation techniques of clogging are discussed. Finally, an example is given how Process Controlling has been employed to soil conditioning in a tunneling project with highly clogging soils.PROCESS CONTROLLING Being both the active part and a huge measuring device, the shield machine represents the core component in mechanized tunneling. This machine comprises a manifold of complex components and devices that require constant supervision and control and, thus, is equipped with a manifold of different sensors that provide a continuous monitoring of the state and condition of the machine (Maidl & Stascheit, 2014). If these data are put into the whole context of the tunneling process, they can provide insight to the assessment and optimization of the performance and to the prediction of potential risks and hazards such as, for example, the tendency of clogging of the cutter head."

Jan 1, 2016

By Ajay Mahajan, Manoj Mohanty, Vishal Gupta

Modern coal processing plants utilize multiple cleaning circuits to efficiently beneficiate different size coal fractions of run-of-mine coal. An older plant optimization approach is to maintain average product quality from individual cleaning circuits at the same level as the given product specifications for the overall plant. However, many past studies indicate that the equalization of product quality approach fails to produce the maximum plant-yield. A newer approach, known as equalization of incremental product quality, requires that the incremental product quality obtained from each circuit be maintained at the same level to satisfy the overall plant product quality. This approach ensures the maximization of plant yield while satisfying a single product quality constraint. However, while dealing with multiple product quality constraints, this approach by itself may not be sufficient to obtain the desired maximum yield. For the simple reason that the dirtiest particle (or group of particles) with respect to one quality constraint may not be the same particle (or group of particles) with respect to another quality constraint, the mass yield versus product quality relationship generated by equalizing different incremental product quality may not be exactly the same. Therefore, an additional search technique has to be utilized to determine the global-maximum value of plant yield. Thus, the main objective of this study was to utilize an emerging optimization technique, known as genetic algorithms (GA) to maximize plant yield while satisfying multiple product quality constraints. The maximum plant yield obtained from this approach was nearly same as the maximum yield obtained by the incremental product quality approach while satisfying one specific product quality constraint. The GA was applied on a coal preparation plant that utilizes four circuit operations - heavy medium bath, heavy medium cyclone, spiral and froth flotation. The results showed that using GA as an optimization process gives 2.56% higher yield that will result in additional revenue generation of $5,120,000 per annum than average product quality approach.

Jan 1, 2005

By Ramazan Comakli, Cemal Balci, Nuh Bilgin, Hanifi Copur, Can Polat, Deniz Tumac

"Application of mechanical excavators for rock excavation in both civil construction and mining engineering fields has increased significantly in recent years. Prediction of the excavation performance of any mechanical excavators – tunnel boring machines, roadheaders, impact hammers, continuous miners and shearers for any geological formation is one of the main concerns in determining the economics of a mechanized mining and/or tunneling operation. A new portable linear rock cutting (PLCM) device was developed in the Mining Engineering Department of Istanbul Technical University and supported by The Scientific and Technological Research Council of Turkey (TUBITAK-112M859). The PLCM is used for cutting small core or block rock samples by a real-life mini disc cutter. The results from the PLCM are compared with the results obtained from the full scale rock cutting tests and theoretical model. It is found that there is reliable correlation between test results obtained from both cutting tests and theoretical model. 1. INTRODUCTION Mechanical excavators are currently the only alternatives to drill and blast due to higher production rate, increased safety, uniform muck size, less roof support, easier ventilation, continuous rather than cyclical operation, and possibilities for automatic control. The most of large civil tunneling and some mining projects are now carried out by mechanical excavators rather than drill and blast methods. Mechanical excavators can be categorized into two main groups: full-face and partial-face machines. Full-face machines such as tunnel boring machines excavate the face in one mode at the size of the cutterhead. Due to their cutting mode, the shape of the face profile by the full-face machines can only be circular. As for partial-face machines, the cutterhead is attached at the end of a boom. The face profile excavated by the partial-face machines can be from circular to horseshoe shape due to the cutting mode of the boom."

Jan 1, 2016

By A. Palit, M. K. Mohanty

This investigation has concentrated on optimizing the newly developed Pansep linear screen and developing empirical models to predict the screening performance. Most empirical models developed in the past to predict the performance for industrial screens are suitable for the vibratory screens. Understandably, these models are deficient in predicting the performance of linear screens due to the difference in their operating principle. Thus, the main objective of this study has been to develop empirical models suitable for linear screens to predict the partition coefficient for a given size fraction as a function of the aperture size. The inadequacy of the conventional model equation originally developed for vibratory screen has been demonstrated and a modified equation developed to predict the partition coefficient as a function of the normalized mean particle size (d/d50c). In addition, new model equations have been developed for linear screens to predict the screening efficiency as a function of the separation size(d50) and to predict the separation size as a function of the screen aperture. It is believed that these model equations will be useful for the plant operators in selecting the mesh panels of correct aperture size and in predicting the product size distribution based on the selected aperture size.

Jan 1, 2003

By Jamai Rostami

Mining, perhaps more than other industries, has been under pressure to achieve higher productivity, while reducing costs and environmental impacts. This has encouraged a move toward large-scale operations and greater integration and automation of systems. Mechanization is being used increasingly to raise production and reduce labor requirements. Yet, while transportation, ventilation and other activities have benefited from this trend, mechanization of rock excavation (for development and production) has lagged. The switch to a mechanized excavation system can be complex, requiring a thorough study of operational and cost benefits to be successful. To justify the high capital cost of mechanical mining equipment, production rates and the true costs of machine mining must be accurately estimated. To evaluate the cost effectiveness of mechanical mining for a particular operation, the total production cost (capital and operating) must first be estimated. This requires a reliable estimate of the production rate of the candidate mechanical excavator. Previously, the variable nature of rock caused performance prediction of these machines to be more an art than a science. Additionally, some of these machines are highly sensitive to operator skill. They all depend on their backup systems. The effects of interaction with the overall mining operation can be difficult to forecast. And a new system must surmount psychological barriers before it can become truly operational.

Jan 1, 1994

By Nobuharu Isago, Atsushi Kusaka, Kosuke Kawata, Dohta Awaji

"The immediate ring closure method, in which the entire periphery of the excavation area is closed immediately with an initial support within a short distance from the excavation face, has been increasingly used in Japan, especially, as one of the most effective countermeasures against difficult ground conditions in conventional tunneling. For reasonable design of this method, the performance requirements for the initial support should be clearly stated. The analysis of construction data of 30 road tunnels and the three-dimensional numerical modeling based on real data suggest that the immediate ring closure stabilizes the tunnel structure and the ground around it because of the inner pressure effect of the initial support, especially, for low ground competence factor and small internal friction angle. Finally, the bending compressive strength and the cross-sectional geometry of the initial support have to be considered in the tunnel design while considering the earth pressure and ground properties. INTRODUCTION Conventional tunneling methods often deal with difficult ground conditions such as soft ground or squeezing ground conditions. The immediate ring closure method, in which the entire periphery of the excavation area is immediately supported within a short distance from the excavation face (Figure 1), has been increasingly used in Japan as one of the most effective countermeasures against difficult ground conditions in conventional tunneling (e.g. Takahashi et al., 2011; Nakaoka et al., 2013). The immediate ring closure method was empirically identified as effective for reducing ground surface subsidence and tunnel deformation. However, the working effects of the method have not been clarified sufficiently. To improve the design of this method, the working effects of this method and the performance requirements for the initial support need to be clarified. The relation between the effect of immediate ring closure and earth cover has been clarified (Mashimo et al., 2008; Awaji et al., 2013),"

Jan 1, 2016

By Tim Wolf, Barry Fink

Mine site managers reported occurrences of locking assembly bolt failures on the Enlow Fork Coal Mine's slope belt conveyor. The observations were made after a number of years of operation and raised questions as to the status of the assemblies in operation. These questions prompted a detailed review of the situation by independent consultants. Using operational history of the conveyor and confirmation of belt loads by static and dynamic methods, a locking assembly fatigue curve was created to suggest expected service life. From this work, suggestions were made to modify the pulley assemblies for extended service life.

Jan 1, 2002

By W. E. Sabina

In the short period of one mans? career we have seen specifications for bulk material handling systems and equipment grow from two or three pages to as much as two or three volumes for a single contract. The old 'short form' described what the purchaser expected the equipment to do. The long form does the same but also includes nut, bolt, and lockwasher depth of detail. What are the events that led to this proliferation of verbiage, and does it benefit the buyer in the final analysis? Is there a better way to purchase complex equipment while ensuring the highest quality for the dollar spent?

Jan 1, 1986

By William E. Bruce

Percussive drill calibration experiments performed by the Bureau of Mines on two drills are described. The use of a linear velocity transducer to determine piston velocity, blow frequency, and piston stroke length is discussed. Data are presented on the relationships between maximum work rate and feed air pressure. Penetration rates in nine rock types were measured for the same two drills. Physical properties of the nine rock types are presented in tabular and graphical form to show relationships between penetration rates and physical properties. Finally, conclusions are drawn as to the potential use of these data to predict percussive drilling rates.

Jan 1, 1970

By Jack V. Hill

A unique type of grinding mill liner has been developed by Waagner-Biro A.G. of Austria. This liner system, termed an angular spiral lining (.ESL), was, successfully tested by Magma Copper Company's San Manuel concentrator in both their 10 Ft x 10 Ft (3.05m x 3.05m) and 12 Ft, 6 In x 14 Ft (3.81m x 4.27m) grate discharge wet grinding ball mills. Magma Copper's savings in power and grinding balls justified conversion of more than half of their twenty-six ball mills to the ESL system.1,2 The ASL system was provided by the Capitol Castings Division of Midland Ross Corporation, the exclusive licensee for such conversions. Capitol Castings proposed the following as expected benefits from installation of an ASL system in an 18 Ft x 21 Ft (5.49m x 6.40m) overflow discharge wet grinding ball mill at the Pinto Valley Operation of Cities Service Company: "(a) Reduction of power consumption per ton of ore milled = 12%, (b) Increased throughput = 6%, (c) Reduction of ball consumption = 6%."

Jan 1, 1982

By A. P. Schissler

2013 has seen metals, industrial minerals, and coal all reduce in price due to market and geo-political factors. Many companies are taking write-downs to recalibrate their reserves and have enacted focused cost reduction programs. The public domain includes statements where companies have operating cost reduction goals in the $500 million range. Zero-base staffing & budget analysis is a means to achieve optimal employment and cost levels for a given level of production. The method involves measuring the work to be done similar to Lean. Lean is a method to review each step of production and remove anything that doesn?t add value or is necessary to complete finished goods. Zero-base methodology has been applied to mines worldwide producing realistic and sustainable levels of staffing and costs based on the quantity of work. The objective of this paper is to provide the framework of zero-basing with examples of application.

Feb 23, 2014

By James M. Barker, Richard O. Y. Breese

The recognition of perlite as a distinct volcanic glass, and of the arcuate fractures that often characterize these natural glasses, dates back at least to the late 19th century and perhaps into the 18th century (Howell, 1974). Some authors suggest that recognition of perlite dates considerably further into antiquity, perhaps to the 3rd century BC (Caley and Richards, 1956). Most recent definitions identify perlite by the presence of vit¬reous, pearly luster and by the presence of characteristic concentric or arcuate perlitic fractures. As discussed more fully below, arcuate fractures in perlite need not be megascopic. The textures of perlite which commonly occur in deposits range from dense to highly vesiculated to pumice-like. Thus, the classical definition of perlite is descriptively restrictive compared to the natural range of textures and neglects to address the issues of genetic origin and geologic occurrence. In spite of the petrological usage of the term perlite, the in¬troduction of expanded perlite aggregate into industrial markets caused the term to be applied as well to the lightweight, cellular aggregate that is produced through the rapid thermal expansion of milled perlite ore. Perlite is distinguished petrologically from other natural glasses by a silicic or rhyolitic composition by the presence of 2 to 5 wt% total chemical water held within the glass structure and often by the presence of pearly luster and onionskin-like perlitic fractures. Worldwide, occurrences are associated with Tertiary through early to middle Quaternary volcanics and with the glassy portions of silicic domes and flows, with vitric tephra, with the glassy chill margins of dikes and sills, and with the glassy portions of welded ash flow tuffs. Less commonly, perlite is reported in association with the glassy portions of volcanic plugs and lacco¬liths. The perlite carapaces that partially or fully comprise extru¬sive domes and flows are often thick and areally extensive, and thus provide commercially attractive targets for low cost open pit mining. Perlite tuffs and tephras are also important commercial sources. Mining costs are minimized by open pit quarrying and by either bulldozer ripping or blasting. Crushing and sizing facilities are generally close to the pits. Due to the low weight and large volume of expanded perlite, unexpanded perlite that has been crushed and sized is usually shipped nationwide directly to local markets where it is expanded and processed for distribution to end users. The vast majority of international trade is in unexpanded perlite. In the United States, the evolution of the expanded perlite industry can be traced to the late 1930s and early 1940s when expanded perlite aggregate was introduced into gypsum plaster and concrete markets as a substitute for vermiculite (Schundler, Jr., oral communication, 1991) and was promoted for use in a much broader spectrum of products (Howell, 1974). By the early 1950s, end user markets were well established and small expanders were numerous east of the Mississippi River. Today, mining and expan¬sion is undertaken throughout the world. Worldwide production of perlite is dominated by the former Soviet republics, the United States, and Greece. Total worldwide production of processed perlite during 1990 is estimated at roughly 1 778 000 tons (Davis, 1991). The physical properties of expanded perlite that give this prod¬uct unique commercial value include: low bulk density, chemical inertness, high insulating ability, nonflammability and fire resis¬tance, and its ability to retain water. These and other physical properties give expanded perlite value in such uses as: lightweight acoustical and thermal insulating aggregate; component in plaster, insulating cements and lightweight concrete; loose fill insulation; as aggregate in horticultural applications; and in milled form as filter aid. In the United States and Europe, the largest end use is within building construction products.

Jan 1, 1994

By M. R. Bowie, J. M. Barker, J. S. Hingtgen

Techniques of testing perlite require a combination of art and science. The modifications made to the perlite Corp. vertical laboratory furnace include addition of instrumentation, flowmeters, vibrators, automatic feeders, and regulators. The basic testing sequence consists of expanded density, furnace yield, compacted density, percent sinkers, and compaction resistance. These tests are modified versions of those specified by the Perlite Institute. This sequence is designed as a preliminary evaluation of a material's suitability for horticultural-aggregate end uses rather than a detailed measure of filtration capability.

Jan 1, 1988

By L. M. Turner

Perlite is a unique mineral that upon heating expands to about twenty times its original volume. Mining is by open pit method. The processing cycle involves crushing, screening and sizing the ore. An on-site quality control facility at the Manville Products No Agua mine exerts a high degree of control over every phase of the operation from blasting to finished product.

Jan 1, 1985

By J. M. Barker

New Mexico is the leading domestic producer of perlite, a hydrated volcanic glass that can be expanded thermally to form a white, very porous, lightweight material. The United States is the leading consumer and producer of perlite in the world (Pettifer 1981). New Mexico produced, at five mines (Fig. 1), about 86% of all domestic crude ore mined in 1984 (Meisinger, 1985). Perlite is mined in 6 other western states, ore is expanded in 33 states, and the expanded ore is consumed in all states (Meisinger, 1985). Gross value of domestic ore mined in 1984 was about $16,500,000 (FOB mine; Meisinger, 1985) with much value added by expansion and processing prior to sale to end users. In contrast to the ubiquitous nature of perlite products in the U.S. economy, facilities for testing perlite ore, expanded perlite, and perlite products are notably lacking on a commercial, cost-effective, or readily accessible basis. The New Mexico Bureau of Mines and Min¬eral Resources (NMBM&MR) established a perlite¬testing facility in 1984 to mitigate this lack and to further the mining of perlite in the state.

Jan 1, 1985