Search Documents

By B. Bringhurst, J. J. McClelland

A filter consisting of a synthetic fibrous material has been determined to be a viable alternative to the wire mesh panels currently used in irrigated filter dust collection systems. An extensive laboratory investigation of the material showed that it removed a higher percentage of both respirable coal and quartz dust from the air entering a collector than did the flat and pleated wire mesh panel designs. This improvement in dust collection efficiency reduced the amount of coal and quartz dust discharged from the collector exhaust by approximately 44%. Since continued exposure to excessive levels (>5%) of respirable quartz dust presents a severe health hazard, this alternative filter medium could be of use to those mines required to comply with more stringent dust standards due to quartz.

Jan 1, 1992

By M. Ribeiro, P. So, P. Wong

Electrowinning is a process by which metals, such as copper or nickel, are recovered from aqueous electrolyte solutions resulting from the extraction of the metal ion from an acidic or basic leach solution. The electrolyte or “pregnant” solution is customarily forwarded to an electrowinning "tankhouse." In the tankhouse, the metal ions are deposited on cathode plates by electrodeposition and then recovered from the cathode plates. Other processes may be employed with other metals, such as nickel, zinc, among others, to produce an electrolyte from which their respective metals are obtained. During the electrowinning (electrodeposition) stage, elemental metal is plated out at the electrowinning cathode and oxygen evolves at an insoluble anode. The evolution of oxygen gas forms bubbles which entrain strong acid electrolyte, carrying it into the air above the electrowinning tank in the form of a fine mist or spray when the bubbles break. An acidic mist is generated above the electrolyte. This mist or spray then spreads throughout the electrowinning tankhouse. The acidic mist is corrosive and a health hazard and can cause extreme discomfort to the skin, eyes, and respiratory systems of tankhouse workers, especially during hot weather conditions. Polyfluoroalkyl based products (PFAS) have been widely applied as anti-misting agents in the electrowinning of metals in an acidic electrolyte. Functionalized PFAS compounds, however, have come under increased scrutiny by the EPA due to their impact on human health and the environment. There remains need for improved acid mist suppression agents for electrolysis and electrodeposition, particularly for products free of fluoroalkyl components.

Feb 1, 2023

By T. S. Golosinski, J. Wolski

Procedures are presented for determining the hourly production rate, mechanical and physical availability, utilization, use of availability, and global performance factors for the bucket wheel excavator (BWE) itself, as well as for the system composed for the BWE, conveyors, and stacker. An example demonstrates the flow of calculations. Using available data from mines that use BWE technology, the ranges of values of the BWE performance factors are presented in tabular form. They can be used as a guide during mine planning as well as to evaluate existing systems.

Jan 1, 1987

By Jan Wolski

Increasing interest in the Bucket Wheel Excavator (BWE) technology calls for a universally understandable definition of suitable performance factors which would reflect the unique features of this technology. The importance of properly designed and calculated performance factors for the BWE systems cannot be overemphasised. They are used by all levels of management in any mining organization for a wide variety of purposes, in particular for budgeting, for selecting new equipment, for monitoring current equipment and for comparison with other operations.

Jan 1, 1984

By D. Rutledge

Discrete (digital) signal processing techniques are proving to be very valuable tools for miners using the block cave method. Waveform analysis of different measured signals associated with active mining provides valuable information on production dynamics and safe operation of the mine. For example, correlation of the three-dimensional surface displacement velocity waveform and the production output waveform reveals a remarkably predictable time-varying physical process. In this paper, the authors discuss the signal processing techniques used to study these relationships, as well as the related implications for mining.

Jan 1, 2008

By D. Rutledge

Discrete (digital) signal processing techniques are proving to be very valuable tools for miners using the block cave method. Waveform analysis of different measured signals associated with active mining provides valuable information on production dynamics and safe operation of the mine. For example, correlation of the 3D surface displacement velocity waveform and the production output waveform reveals a remarkably predictable time-varying physical process. Studying the geometrical and temporal relationship between these two signals opens a broad window through which new management techniques become apparent. In this paper we discuss the signal processing techniques used to study these relationships, as well as the related implications for mining. This research was carried out in association with the Chevron Mining underground molybdenum mine in Questa, New Mexico. Some of these new techniques will be integrated into the decision management process at the mine and will provide insight on ore production, draw control, and safe reclamation. The science of signal processing involves the analysis and interpretation of physical processes that vary with time. Two general categories of signals1 are recognized. A continuous signal is a waveform of varying amplitude that is continuous in time (such as a sine wave). A discrete signal is a sequence of quantized values. The independent time variable and amplitude are sampled periodically such that we only know the value and shape of the waveform at the sampling frequency. Displacements measured by a Global Positioning System (GPS) receiver are an example of this. Discrete signals may be studied in the time, frequency, autocorrelation, or wavelet domains. In this paper the amount of ore extracted from the mine and the measured surface displacements are analyzed in the time domain.

Jan 1, 2008

By Wen Lan Chen

In the plant where the 800m diameter cyclone was tested, 500 STPH of 50m x 0 raw coal was pulped in a heavy medium tank and pumped originally to four 700mm heavy medium cyclones. For the test one of these units was replaced by an 800mm diameter cyclone with the subsequent feed pressure for both units sets at approximately 15.0 psi. Since this was a feed to zero plant, an appropriate bleed of heavy medium to the dilute medium circuit was established to en- sure that the cleaning of the 500m x 0.5mm raw coal would not be adversely affected by high levels of 0.5mm x 0 fine coal present in the heavy medium. The medium gravity measured varied between 1.41 and 1.43. During a three-hour test on June 10, 1983, the raw coal sample was collected from the feed belt while the clean coal and refuse samples were collected separately at proper locations along the product streams of the two different diameter cyclones. All of these samples were shipped to the laboratory for screen and sink- float analyses. The raw coal screen and ash analyses are shown in Table 1.

Jan 1, 1984

By Walter E. Jaworski, William R. Beloff, John Dunnicliff

As a step in the endeavor to reduce future tunneling costs in New York City, the Environmental Protection Administration, Dept. of Water Resources, instituted a program in 1972 to monitor the performance of the lining of one of its tunnels. A monitoring program was included as part of the contract specifications for the East Branch Interceptor Sewer tunnel for the Port Richmond Water Pollution Control Project in the hope that measured data would indicate possible future cost effective design or construction improvements. The monitoring program involved measuring ground deformations, circumferential liner stresses, longitudinal liner stresses, and jacking pressures. This paper presents some of the findings from these measurements, with emphasis on liner stresses. PROJECT DESCRIPTION The 3.05m (10 ft) diameter steel lined tunnel was constructed under two separate contracts. The easterly portion, Contract 3A, was approximately 3109m (10,200 ft) in length and constructed by Peter Kiewit Sons Co.1 The westerly portion, Contract 3B, was approximately 2160m (7100 ft) in length, and constructed by Richmond Constructors, a joint venture of Grow Tunneling Corp., MacLean Grove & Company, Inc., Grove, Shepherd. Wilson & Kruge, Inc., Morrison-Knudsen Company, Inc., and Andrew Catapano Co., Inc. Each contract included three test stations, hence a total of six along the tunnel route. Excavated material along the tunnel route consisted primarily of dense fine to coarse sand with varying percentages of gravel and silt with occasional boulders. Pockets of organic silt were encountered on Contract 3B and a large portion of Contract 3A ran through slightly weathered serpentine and schist. Overlying material and the groundwater level varied considerably along the route as did the height of overburden. Figures 1 and 2 show the generalized soil profiles for Contracts 3A (PK stations) and 3B (RC stations) respectively.

Jan 1, 1979

By Luzheng Chen

The study aimed to evaluate the separation performance of a full-scale continuous centrifugal concentrator in the reconcentration of fine hematite from high-gradient magnetic separation (HGMS) concentrate in a tailings recovery plant, and to investigate the usefulness of the technology in industrial applications. The effect of changing the operating variables on concentrate grade and recovery was studied. The results indicate that among the variables considered in the study (water spray pressure, centrifugal acceleration, feed volume flow rate, feed percent solids and the reciprocation and spacing of water sprays), the change in centrifugal acceleration affects the recovery the most and continuous concentration can be achieved only when the water spray has a sufficient pressure. In addition, the reciprocation and spacing of the water sprays have a significant influence on the concentrate grade. Although performance of the full-scale concentrator is slightly inferior to pilot-scale trials, due to limitations in the scale-up design and the fluctuations of feed material characteristics, this concentrator provides a potential way to achieve continuous concentration and obtain a high-grade concentrate from tailings.

Jan 1, 2010

By J. Schoenbacher

Park City Municipal Corporation (PCMC), long before being recognized as an Olympic venue was known as one of the great American silver mining towns. During a century of active mining, the Park City mining district produced millions of ounces of silver in addition to a substantial amount of mine tailing waste. Since 1985 the City has been remediating these impacts with state and federal oversight. One particular challenging CERCLIS site, that was previously a historic mine tailings pond is known as Prospector Square Development (CERCLIS Listing Silver Creek Tailings UTD98051404). This site has been very challenging due to the metals that impact the shallow ground water that eventually drain into the Silver Creek Watershed. To address the water quality impairment the City and Missouri University of Science and Technology teamed up to investigate the feasibility of constructing a horizontal-flow wetland to treat this pollutant source. This effort began with the building of a pilot cell in June of 2004 and lead to the construction of a full scale horizontal-flow wetland in the fall of 2008. The design of the pilot and full scale biocell was based upon lab-scale research conducted by the Missouri University of Science and Technology. In October of 2008, the Prospector Drain effluent was introduced to the system and to date analytical results reveal that the biocell is treating the Prospector Drain outfall below the Silver Creek Total Maximum Daily Load (TMDL) endpoint goals for zinc .39 mg/L and cadmium .00075 mg/L. The water chemistry of the influent, that originates from the historic silver mine tailings pond, is impaired with zinc and cadmium and has low iron with a pH of roughly 6.5. The construction of this unit encountered many challenges related to constituent relations, regulatory scrutiny, constructability and start-up. Nonetheless, since implementation this unit is considered a success for improving water quality within the Silver Creek Watershed.

Jan 1, 2011

By James P. Rider, Robert P. Vinson, Fred N. Kissell, Jon C. Volkwein, Gregory J. Chekan, Jay F. Colinet

The Thermo-MIE personal DataRAM dust monitor (pDR) is a light-scattering instrument approved for use in gassy underground mines by the U.S. Mine Safety and Health Administration (MSHA). However, the use of lightscattering monitors has been inhibited by concerns about inaccurate readings resulting from changes in dust size distribution and composition, as well as concerns about the impact of moisture in the mine air. Because of this concern, the National Institute for Occupational Safety and Health (NIOSH) has evaluated the pDR using available data from laboratory tests and mine surveys. The data show that accuracy can vary widely from test to test and mine to mine. In most cases, the results can be improved by using a companion gravimetric measurement to adjust the pDR data.

Jan 1, 2005

By Felipe Calizaya, Sekhar Bhattacharyya

Mechanized underground mines suffer from noise overexposure. Noise levels are often above the Permissible Exposure Limit (PEL) where underground fans are used. Sound levels in active workings can reach up to 121 A-weighted decibels (dB(A)), especially when fans are not equipped with silencers. Use of silencers seldom ensures PEL. Overexposure of noise induces permanent hearing loss among mine workers. A NIOSH-funded research project and field studies at six coal and non-coal mines revalidated the findings. The University of Utah undertook laboratory studies to reduce fan noise at the source. A new silencer prototype with varying noise dampening material was designed and tested. The silencer and associated extension can be repacked with different dampening materials. The silencer and the extension were used in various configurations. Attempts were also made to simulate field conditions. The tests demonstrated a maximum sound level attenuation of about 14 dB(A) at the fan discharge. A properly designed silencer offers lesser resistance and thereby better fan performance and lower energy cost. The re-packable silencer is more likely to be maintained properly. Lowering of noise level happens in audible frequencies (4000 to 8000 Hz) which are important in A-weighting.

By Felipe Calizaya, Sekhar Bhattacharyya

Noise-induced hearing loss (NIHL) is prevalent in mechanized underground mines. Federal regulations are often not complied with effectively. Miners are also prone to ignoring administrative guidelines and/or personal protective equipment for hearing conservation. As a result, quality of life among experienced miners plummets while occupational risks increase at workplaces. This research focused on auxiliary fans used in underground mines. These fans work at high rotational speed and generate extremely high levels of noise in close proximity to miners. Silencers used are often of little effect due to poor maintenance. A new silencer is tried in the laboratory with the objective of easy maintenance and resulting reduction of noise exposure for miners.

By M. Dondi, M. Surracco, G. Alfano, P. Saba

Recent investigations on fine grinding with jet mill miprototypes of original design, constructed at the DIMM and Centro Studi of the National Research Council at Cagliari University, have led to the realization of a third generation micronizer characterized by large capacity and high efficiency. The new model and its distinctive features are described here and the results are presented of grinding tests on typical, high grade Sardinian minerals used for quality products. The operating principles of the jet mill are described in relation to the mechanico-elastic properties of the minerals treated. In particular the efficacy of the comminution process is demonstrated in terms of both solid treated and of impact, attrition and shearing forces generated in the micronizer. Particle size distribution of the finished products are reported, that satisfy the most stringent market specifications for the different minerals, as well as energy consumptions. The alternative operating options for solving particular grinding problems and minimizing energy consumption are discussed. Lastly, the main developments of the jet mill for a possible application at industrial scale are suggested.

Jan 1, 1995

By Patzen Wu

The Hai-Shan No. 1 Coal Mine, located in northern Taiwan, is one of the typical coal mines on the island which, limited by natural condition, are mostly small in scale. With the advancing longwall method, the mine is now winning a seam, 80 cm thick, at a 32° dip, with a working depth of 824 m below surface. The annual output is about 50,000 mt of clean coal. At the working gallery, the virgin rock temperature may go up to 46°C, difficult to be brought dam to n acceptable level: because .of the tropical climate with high intake temperature and high humidity. Besides, at this depth, the intake air that goes down the long inclined shaft generates considerable heat due to autocompression. The mine is ventilated by a set of axial-flow fan with 38 m3/S of intake air at 2.2 KPA WG. With this volume of air, the temperature at the working-face is usually above 30°C WB. Appreciable lowering of the temperature is not expected even with an increased volume of ventilated air. For this reason, decision has. been made to try the installation of a pilot underground refrigeration unit near. the lowest gate road to cool the intake. air. from 32°C WB to 28°C WB which seems acceptable to on-the-spot workers exerting heavy physical labor. The experimental unit is designed for carrying away a total heat load of 90 Kw. The capacity of the unit is 200 Kw. The unit consists of a compressor, an evaporator, a condensor and a motor. The heat rejection is done in a cooling tower. Chilled water is circulated from the evaporator to the cooler by insulated pipes. The cooler consists of 90 Kw-coils with two fans and forces air by flexible ducting onto the working face. This paper examines mainly the effect of this additional reduction of working temperature, on working efficiency of the workers. Another aspect of this experiment is to evaluate the overall economy of underground refrigeration in small-sized coal mines under tropical condition. The success of such an experiment may lead to wider application of refrigeration to render many of the deeper mines economically workable.

Jan 1, 1980

By Edward J. Cording, William H. Hansmire

INTRODUCTION The Washington Metro, a rapid transit system that will serve the District of Columbia, Virginia, and Maryland, has been under construction for about two years. Construction of the Metro by the Washington Metropolitan Area Transit Authority involves a large amount of cut and cover, soil tunnel, and rock tunnel construction. To aid initial construction and improve future designs, performance observations were undertaken on tunnels in the initial construction phase. The University of Illinois Department of Civil Engineering was engaged to carry out a comprehensive program of field observations and measurements for this purpose. One part of the program was on the first soft ground tunnel constructed in the system. The tunnel is a 2200-ft (670 m) twin-bore section, designated Contract A-2, in downtown Washington. Two objectives of this program were to determine the relationship of construction procedure to settlements and to observe the pattern of soil movement around the tunnel as an aid in evaluating underpinning criteria for nearby structures. A test section, consisting t three instrument lines located across the tunnel path, was established prior to mining in Lafayette Park to measure in detail both vertical and lateral soil displacements as the tunnel was mined through the section. The site was selected because it is free from surface structures and access for installation and reading of the instruments was convenient. Load and distortion measurements on the lining were also made within the test section; observations of construction procedure were maintained throughout construction.

Jan 1, 1997

By Athorn Mary-Lee, Randall A. Snowdon

During the development of the Selby Coalfield, UK, a Robbins full-face tunnel boring machine (TBM) and a Thyssen Titan roadheader were used to drive a pair of parallel spine roadways. This paper presents a summary of the comparative operational and cutting performance of both the Titan road- header and the Robbins TBM. Statistical techniques were employed to identify relations between machine performance and geotechnical parameters.

Jan 1, 1986

By J. L. Carr

Continuous mining machines are extensively used in the underground coal mining industry. These machines are typically remote-controlled, and severe injuries and fatalities occur every year when a miner is struck or pinned by the machine. Proximity detection systems offer a means to prevent these types of injuries and fatalities by sensing the presence of a miner and disabling machine motion. Researchers at the National Institute for Occupational Safety and Health (NIOSH)have developed the Intelligent Proximity Detection (iPD) system to provide enhanced protection while minimizing false alarms. The iPD system uses a set of pre-defined rules to determine which machine motions are safe and which would present a potential hazard, and automatically disables only the potentially hazardous motions. This system has been installed and tested on a Joy 14CM continuous mining machine at the NIOSH Office of Mine Safety and Health Research in Pittsburgh. Under laboratory conditions, the achievable accuracy and performance of the iPD system has been quantified with respect to a number of variables including position of the conveyor boom, presence of the machine?s trailing cable, and orientation of the miner-wearable component. Disclaimer: The findings and conclusions in this report are those of the author(s) and do not necessarily represent the views of the National Institute for Occupational Safety and Health. Reference to specific brand names does not imply endorsement by the National Institute for Occupational Safety and Health.

Feb 27, 2013

By M. J. Mrugala

Typically the conventional pillar design methods consider the behavior of the pillar alone. In such analysis the contribution of the associated roof and pillar is not considered. The focus of this paper is a study of pillar behavior in the context of interaction between a different rock material sequence in the associated roof and floor. The finite difference element code FLAC (1)is used to perform modeling of pillar response to various stratigraphic sequences.

Jan 1, 2003

By G. Ferrara

To obtain a reliable comparison between conical and cylindrical separatory vessels used in dynamic dense medium separation systems, the following studies were made: (1) study of the swirling flow in conical and cylindrical vessels using laser-Doppler velocimetry (LDV); (2) study of the behaviour of suspensions of magnetite and ferrosilicon in water in both separators. It was found that: (a) the tangential velocity profiles differ in conical and cylindrical vessels: in a conical cyclone free vortex conditions affect the largest part of the vessel, while in a cylindrical vessel, the motion approaches that of a forced vortex, i.e. that of a centrifuge; (b) the conical vessel manifests higher centrifugal acceleration and very strong densifying; the density differential, and hence the density gradient inside the vessel is large; (c) the cylindrical vessel manifests lower centrifugal acceleration and low densifying, i.e. low density differentials, and hence, the density gradient inside the vessel is small; (c) due to greater densifying, the density cut-point in cyclones is higher than the operating medium density, while in cylindrical vessels the density cut-point is closer to the medium density. The results provide an interesting description of the differing behaviour of conical and cylindrical vessels and help explain the differences in performance between the two types of separators.

Jan 1, 1998