Search Documents

By Matthew J. DeMarco, Anthony T. Iannacchione

Coal bumps have presented serious mining problems in the U.S. throughout the 20th Century. Fatalities and injuries have resulted when these destructive events occur at the working face. Persistent bump problems can result in abandonment of large reserves or lead to premature mine closure. Through the years, a1ternative techniques such as artificial supports, extraction sequencing, destressing, pillar design changes and specific pi1lar retreat practices have been successful1y imp1emented to mitigate coal mine bumps. Several techniques have evolved for room-and-pi1lar operations that control the way the roof rock breaks, regulating the manner in which stresses are redistributed in the mined section. Special mine layouts employed in longwall mines have also proved to be successful in safely redistributing or containing excessive loadings. However, with ever increasing production rates, greater overburdens and new mining systems, the need to evolve even more effective bump control designs will continue to challenge the U.S. coal mine industry.

Jan 1, 1992

By Kadri Dagdelen

Production scheduling of an open pit mine is one of the most important steps in open pit mine planning. The production schedule of a mine defines the distribution of cash flows and as a result directly influences the net present value and overall economic feasibility of a project. It is becoming more and more critical to obtain an exploitation schedule of a deposit such that highest possible returns are achieved from a project. As the mining industry mines lower and lower grade ores, production scheduling is becoming a key item which can make or break a project. Although the need to plan and operate a mine with an optimum production schedule has been obvious for some time, the methods used to obtain such a schedule have not been. There is not a single, mathematically proven, optimum mine production scheduling algorithm which is widely accepted and used today. In an attempt to determine a production schedule which is optimum, a new algorithm was developed. This algorithm, in theory, is based on the lagrangian concepts of mathematics and in practice is based on the parameterization concept of mining. This paper describes the fundamentals of this newly developed algorithm.

Jan 1, 1986

By Y. C. Kim

For the past quarter of century, much more effort and research have been expended in developing the "optimum" ultimate pit limit design algorithms and much less to solving the "optimum" open pit production sequencing. However, the potential economic benefit to an operating mine is far greater for the latter than the former. Unfortunately, the problem of "optimum" open-pit production sequencing has not been fully solved to date. This paper first reviews the past and currently used methodologies for developing this sequence. The staggered pit phase geometry problem of advanced stripping and operational constraints such as ore and waste tonnage requirements by period and necessary contiguity of mining faces are the main reasons why the "optimum" production sequencing problem has not been solved as yet. This paper also explains why any method which attempts to simplify the problem using ultimate pit limit design algorithm will fail to reach an "optimum" solution.

Jan 1, 1994

By Sebastian Avalos, Julian M. Ortiz

The long-term mine scheduling is the optimal decision on how to extract and process the mining reserves. The resulting plan is mainly driven by economic, metallurgical, and geological factors. Accounting for their uncertainties leads to a robust solution and the feasibility for economic-risk quantification. In this work, we model the spatial uncertainty of grade distributions of multiple correlated elements, by using a multivariate morphing transformation. The result is a set of multivariate geostatistical realizations of the grades, which honor the conditioning data, the direct and cross variograms, and the multivariate statistical distribution, inferred from a set of samples. These models are the input in a reinforcement learning framework, adopted to train a deep neural network that considers the grade uncertainty and leads to an optimum mine plan after training using deep Q-Learning. Mining and processing capacities, as well as economic parameters and metallurgical constraints, are incorporated as the reinforcement learning environment rules. The method is validated on a real deposit, providing insights for future applications.

Jun 25, 2023

By David A. Campbell

There has been a long history of ironmaking on the North East coast of England centered around the River Tees. The industry developed here because of the availability of good coking coals to the North in Co. Durham, and the discovery in 1851 of ironstone in the nearby Cleveland Hills, South of the .River. Cleveland ironstone is relatively poor in quality, with an iron content not exceeding h% and high proportion of sulphur and phosphorous. The iron exists in chemical association with alumina and silica, and physical beneficiation processes involve a serious loss in iron unless the upgrading is limited, when the economics of the process become doubtful. Over the years, richer foreign ores have replaced the local ironstone, and the last operating mine was closed in 1964.

Jan 1, 1982

By Ross Glanville

The Optimum Production Rate (OPR) is one of the most important parameters in the evaluation of a mineral deposit. The OPR cam also be expressed as the Optimum Mime Life (OML) in years since the expected mime life is determined by dividing the OPR per year into the estimated ore reserves. Unfortunately, very little time and effort has been directed towards the determination of the OPR. Instead, "rules of thumb" are often applied to select a mime life without due consideration of the economic implications of such a selection. A "justification" for a particular production rate is often based on a pre-conceived arbitrary requirement for a mime life of 5, 10, or 15 years, for example. In this paper it is demonstrated that such arbitrary selections for high-grade/low¬-tonnage mines (such as many underground gold/silver deposits) often lead to sub¬optimal results. In fact, am apparently uneconomic deposit at am arbitrary production rate may be economic at the OPR. Consequently, investment opportunities may be overlooked if one analyzes mime' properties based on arbitrary production rates.

Jan 1, 1984

By Prashanta K. Chatterjee

The planning of an underground coal mine requires a complex blend of technical expertise, experience and subjective design criteria implemented by the mining engineer. Currently the procedure is largely manual and requires considerable resources to generate a single mine plan. Often three or four people are assigned to work in the development of a single draft layout. Evaluation of the layouts is also tedious as it requires many repetitive calculations. The evaluation of layouts developed manually generally attempts to derive a single economically feasible solution. Operational constraints in underground coal mining such as manpower, time, equipment, etc, do not allow the generations of more than one alternative layout. As a result, the first plan is generally the only one considered. Computer-aided mine planning can automate many of the manual procedures and calculations involved in mine planning thus allowing to evaluate many layouts and mining strategies and to select the optimum plan with confidence. An optimized planning procedure will also provide the capability to evaluate mine performance continuously and critically, thereby helping to maximize return on investment.

Jan 1, 1986

By Ben L. Seegmiller

How to obtain optimum slope angles for future open pit mines using the rock mechanics approach is the subject of this paper. In the past ten years significant developments in open pit rock mechanics have come about. This has been due to the mining industry's need for the steepest, yet safe, pit slope angles attainable. Requirements for economically achieving slope stability and the actual payoff that may be achieved through stability studies have been previously discussed', by stability engineers. While the emphasis has generally been placed on the concept of "stable slopes" in the past, it is suggested that emphasis now be placed on "optimum slopes" or "optimum slope angles". A definition of an optimum slope angle is one which (1) is as steep as possible and practical from orebody and mining constraint standpoints and yet, (2) maintains the accepted standard of safety defined by a safety factor against failure and/or a probability of failure. In other words, the emphasis is placed on achieving practical stability results as defined by safety and economic considerations, as opposed to simply achieving stability. The essential purposes of this paper are to (1) outline the need for optimum slope angles, (2) discuss the procedures for using the rock mechanics approach in slope angle design for a future open pit and (3) specify the end results that may be achieved by using such an approach. While the basic concepts and recommendations outlined in this paper may be equally applicable to soil as well as rock slopes, the emphasis and procedures have been directed at rock slope angle design.

Jan 1, 1976

By Fengyu Ren, Ruslan Puscasu, Kunpeng Yu, Gideon Chitombo, Liangliang Kang

Weak rock mass and poor flow of material can cause excessive ore loss and dilution in sublevel caving. This paper proposes a method to establish design parameters for an inclined deposit within a weak rock mass and evaluates its effectiveness through a case study. In order to solve the problem of low production capacity and poor safety conditions of sublevel caving mining at the Yingfangzi silver mine in China and to ensure a smooth production from the refractory ore body, it is necessary to select appropriate stope structure parameters. Based on random medium theory of gravity flow and the improved equation of ore discharge in random medium, an end wall drawing experiment is carried out to determine the optimum design and flow parameters. It was observed from the experiment that, due to the influence of the randomness of particle movement, there is a mismatch in the flow parameter measurement. The flow characteristics and distribution of the marker particles are different from that of the tested particles resulting in large drawbody shape distortion. The study finds that the flow parameters obtained by the new method are more practical and account for drawpoint width and recommends that the new method for determining the sublevel stope height is used when the drawbody is a non-standard ellipsoid. The outcomes have shown a significant reduction in the dilution and improvement in the recovery rates, and the safety and efficiency of mining have been greatly improved.

By Fengyu Ren, Ruslan Puscasu, Kunpeng Yu, Gideon Chitombo, Liangliang Kang

Weak rock mass and poor flow of material can cause excessive ore loss and dilution in sublevel caving. This paper proposes a method to establish design parameters for an inclined deposit within a weak rock mass and evaluates its effectiveness through a case study. In order to solve the problem of low production capacity and poor safety conditions of sublevel caving mining at the Yingfangzi silver mine in China and to ensure a smooth production from the refractory ore body, it is necessary to select appropriate stope structure parameters. Based on random medium theory of gravity flow and the improved equation of ore discharge in random medium, an end wall drawing experiment is carried out to determine the optimum design and flow parameters. It was observed from the experiment that, due to the influence of the randomness of particle movement, there is a mismatch in the flow parameter measurement. The flow characteristics and distribution of the marker particles are different from that of the tested particles resulting in large drawbody shape distortion. The study finds that the flow parameters obtained by the new method are more practical and account for drawpoint width and recommends that the new method for determining the sublevel stope height is used when the drawbody is a non-standard ellipsoid. The outcomes have shown a significant reduction in the dilution and improvement in the recovery rates, and the safety and efficiency of mining have been greatly improved.

Diamond wire rock cutting is the most widely used technology in carbonate stone quarrying owing to technical performance and block face quality. Interest is also growing for siliceous deposits. This paper deals with the problem of optimum wire utilization under restrictions regarding a set of variables and parameters. A computer program of general applicability has been set up with the aim of studying the most suitable combination of technologies and the effect on the technical and economic results of bench geometry, overall quarry yield, market -stone value, quarry size as well as the quantity, productivity and price of human and material resources and their organization in the elemental working cycle. Two quarrying problems are considered as significant instances a granite and a travertine quarry. The results are illustrated and discussed.

Jan 1, 1989

By P. C. Thakur

In Part I of this paper, it was established that the width of longwall faces in highly gassy mines is primarily limited by the volume of air reaching the tail-end of the face. The ventilation air reaching the tail-end of the face should be not only enough to keep methane concentrations below the statutory limits (generally 1 percent) but also enough to prevent any gas layering. The air volume leaking from the longwall face into the gob should also be able to push the explosive methane-air mixture away from the gob area immediately behind the longwall face where active roof-fall is taking place (typically 30-45 m). The second group of variables that also controls the width of the longwall panel consists of (a) the rate of advance, (b) bleeder air quantities, (c) specific methane emissions for the gob area and, (d) efficiency and cost of gob gas capture. This paper will discuss the second group of variables and its impact on the optimum width of longwall faces in highly gassy coal mines.

Jan 1, 2009

By E. W. Hawk

he power generation industry may be required to reduce carbon dioxide (C02) emissions if regulations related to global climate change are enacted. Coal-fired generation emits more than 80% of the power sector CO2 and would be a likely target for CO2 reductions. Compliance with the Kyoto Protocol will require a 33% reduction from the projected year 2012 emission level, even with moderate load growth. This article describes an analysis of power industry CO2 reduction options and their costs. It assesses how a generator would make compliance decisions under a mandatory CO2 emissions reduction program. Carbon sequestration, fuel switching and new plant construction are considered. The Global Climate Change Treaty signed at the Rio de Janiero Earth Summit in June 1992 set the long-term goal of stabilizing CO2 concentration in the atmosphere. The December 1997 Kyoto Protocol established short-term mandatory targets for the United States and 37 other developed countries. The United States' target is a 7% decrease by 2012 from the 1990 "greenhouse gas" level. Developing countries are exempted from reductions, according to the Kyoto Protocol, despite projections that indicate a significant increase in their emission levels. The Kyoto Protocol must be ratified by the US Senate. US power industry carbon emissions were 490 Mt (540 million st) in 1990 and are projected to be 680 Mt (749 million st) in 2012, according to the US Energy Information Administration. Coal-fired generation emits more than 80% of the power sector CO2. Assuming that the power industry is only required to reduce emissions by a proportional share, a 33% emission reduction, or 225 Mt (248 million st) of carbon, would be required to comply with

Jan 1, 1999

By E. W. Hawk

The power generation industry may be required to reduce CO, emissions if regulations related to global climate change are enacted. Coal-fired generation, which emits 82% of the power sector CO2, would be a likely target for CO2 reduction. Compliance with the Kyoto protocol will require a 30% reduction from the projected year 2012 emission level even with moderate load growth. This paper describes an analysis of power industry CO2 reduction options and their costs to assess how a generator would make compliance decisions under a mandatory CO2 emissions reduction program. Carbon sequestration, fuel switching and new plant construction are considered.

Jan 1, 1999

By Jr. Hawk

The power generation industry may be required to reduce CO2 emissions if regulations related to global climate change are enacted. Coal-fired generation, which emits 82% of the power sector CO2, would be a likely target for CO2 reduction. Compliance with the Kyoto protocol will require a 30% reduction from the projected year 2012 emission level even with moderate load growth. This paper describes an analysis of power industry CO2 reduction options and their costs to assess how a generator would make compliance decisions under a mandatory CO2 emissions reduction program. Carbon sequestration, fuel switching and new plant construction are considered.

Jan 1, 1999

By M. A. A. de Klaver

Functional Description Figure 1 is a typical flowsheet for a system for solid fuel addition to filter cake. Solid fuel, coal, coal breeze, or charcoal, is fed from a,stockpile to a surge hopper. The solid fuel is metered into a grinding mill. The fuel is dried and ground in a grinding mill. The on-size particles are removed from the mill by air sweeping. The ground solid fuel is separated from the air stream by a cyclone and stored in a surge hopper. The ground solid fuel is then pneumatically conveyed to a small hopper in the balling area. The fuel is proportioned into the filter cake just prior to mixing. An efficient mixer is very important to have a successful operation. The exact flowsheet would depend on a number of factors including what fuel is used, how the fuel is received, and the cnaracteristics of the fuel as received. Availability of floor space in the plant may also affect the flowsheet. For example, drying air may be supplied from the pellet furnace if the grinding mill can be located near the grate, or the pneumatic conveying system and a surge hopper may be eliminated by placing the grinding mill adjacent .to the mixing area. Also, for a multiple line plant, a ball mill rather than a roller mill may be more suitable.

Jan 1, 1980

By Hans von Michaelis

This paper examines the process options available for treatment of "refractory" gold ores. As more and more of the easily leached oxidized gold ore zones are exhausted, the pressure is on to find more economical ways of treating refractory gold ore deposits. Historically, refractory ores were generally concentrated, e.g. to make a flotation concentrate that could be roasted. A major development is taking place in the USA in which ores from which gold cannot be concentrated well by flotation are being treated using whole ore oxidation processes prior to cyanidation. Refractory gold ore treatment processes are generally expensive to install and operate. Thus, for a refractory gold ore project to be economically viable, the grade must generally be higher than for free milling gold ores.

Jan 1, 1993

By D. K. Gibson, A. I. M. Ritchie

The phenomenon of acid drainage is likely to occur whenever pyritic rock is broken up, permitting access of air and water. The basic chemistry of the oxidation process is described by the equations below:- FeS 2 +1120 + 7 02 ➔FeS04 +112S04 +1440k.J This reaction proceeds rather slowly, although believed to be bacterially catalysed to some extent. Once sufficient ferrous ions and acidity have been established the following two reactions take over, yielding the same net result but at a much greater rate. First, ferrous ions are oxidised to ferric; this is an extremely slow reaction unless bacterially catalysed.

Jan 1, 1991

By Leslie M. Burnside, Gene E. McClelland, Roy R. Cellan

Revegetation of neutralized heap leach material in the arid environment of the Great Basin represents a challenge of avail­able technology. The chemical and physical environment of spent and neutralized ore is inhospitable for germination and establishment of desirable long term vegetation. Common soil amendments were tested to dete1mine if the heap material could be made more conducive to plant growth. Decommissioned heap material profile samples were collected and reconstructed in columns at bench scale. The column profiles were amended and subjected to three leaching regimes, and representative meteoric conditions. The soil amendments provided positive results for ameliorating the heap material limitations and providing a medi­um conducive to plant growth. The bench scale study also pro­vided insight for the future of heap leach planning and design with successful reclamation in mind at the forefront.

Jan 1, 1998

By J. J. Lewis

In the mid-1970's a major new prospect was proved in a previously unworked region of North East Leicester- shire, United Kingdom. Preliminary estimates from borehole information showed over 500 million tonnes of recoverable reserves. A special Planning Team was set up, to co-ordinate the work for the two local Areas, South Nottinghamshire and South Midlands (management of production of the UK National Coal Board is organised in twelve such Areas). The team was led by one of the authors as Deputy Director, Mining, North East Leicestershire Prospect (NELP). The remit imposed by the National Coal Board was to analyse the possible options of number, location and eventual rates of output of shaft or drift access; to select a recommended alternative in the light of geological, mining, topographical and environmental considerations; and prepare submissions in accordance with standard Board practice on major projects - such submissions including detailed engineering design, financial appraisal, and full risk assessment. To assist the Planning Team, surface and underground consult- ant engineers were appointed to prepare feasibility studies of specific civil and engineering problems.

Jan 1, 1979