Search Documents

By A. Mahmoudkhani

Primary cementing is the process of placing cement in the annulus between the casing and the formations exposed to the wellbore. Portland cement was first used in 1903 in the Lopoc Field in California for well cementing. Since then, the major objective of primary cementing has always been to provide zonal isolation in oil, gas and water wells, i.e. to exclude fluid(s) in one zone from another zone in the well. To achieve this objective a hydraulic seal must be created between the casing and cement and between the cement and the formations, while at the same time preventing fluid channels in the cement sheath. This requirement makes primary cementing the most important operation performed on a well. Without complete isolation in the wellbore, the well may never reach its full producing potential. The industry knowledge on cements relies heavily on empirical data, but the chemistry, physics and structure of cement are not fully understood yet. The strength of concrete can be increased essentially by reducing its porosity through optimizing the size distribution of its components and filling the residual porosity of the hydrated cement phase with inorganic fillers. This approach has successfully utilized in different ways and several technologies for placing high performance oil and gas well cements have been developed over the last few decades. There are reasons to believe that the next source of improvement will lie in the fine-tuning of the hydrates themselves and of the different parameters that drive short (ionic?covalent bonding) and long (ionic correlation) interactions.

Jan 1, 2012

By Colin C. Brooks

The Ok Tedi gold/copper deposit of almost 800 million tonnes was found in I968 because at that time technology had just developed sufficiently to enable exploration of such an area, world markets and prices for copper encouraged exploration for large deposits of low grade ore, Papua New Guinea law encouraged exploration by groups with men, money, management and expertise necessary for successful prosecution of such a search and such groups were already operating in the country.

Jan 1, 1990

By D. K. Grubbs

Anorthosite is an abundant, domestic source of alumina with reserves in individual deposits ranging from a few billion to hundreds of billions of tons. While anorthosite contains less alumina than does kaolinite, its CaO and Na20 contents are significantly higher (Figure 1). Alumina can be produced from anorthosite by alkaline, soda-lime sinter or acid processes. CaO and Na20 are advantageous because they are reactants consumed in alkaline processes. Acid processes require high calcium plagioclase feldspars (bytownite-anorthite) to obtain high alumina extraction because the lower calcium plagioclase feldspars (andesine-labradorite) are not as readily dissolved during digestion. The layered Raggedy Mountain Gabbro group in the Wichita complex in southwest Oklahoma is a high calcium anorthosite that could be processed by acid, sinter, or alkaline methods. Chemical grade limestone in the Arbuckle Group is located within 45 km of the anorthosite (Figure 2).

Jan 1, 1980

By Roger D. Sharpe

Oklahoma contains extensive resources of high-purity gypsum that were deposited in the Anadarko and Hollis basins during Permian time. The gypsum resources and reserves are estimated to be about 48 billion short tons and a; located in the western portion of the state. Oklahoma is the largest producer of gypsum products in the United States. The Blaine Formation and the Cloud Chief Gypsum contain several beds of minable thickness. Four stratigraphic units in the Blaine Formation are quarried in Oklahoma. The Shimer, Nescatunga, and Medicine Lodge Members are quarried in northwest Oklahoma. The Van Vacter Member, consisting of three gypsum beds, is quarried in southwest Oklahoma. The Cloud Chief Gypsum is quarried in the west-central part of the state. The gently dipping gypsum in the Blaine Formation generally crops out along low escarpments and is covered in the downdip direction by increasing overburden, consisting of sand, shale, and/or dolomite. Anhydrite occurs in the downdip direction under the thicker overburden. The Cloud Chief Gypsum crops out as hills, which are eroded remnants of a more widespread, massive sulfate unit. All of the gypsum produced in Oklahoma is extracted using quarrying methods. A variety of products are made from gypsum quarried in Oklahoma. The products are manufactured from uncalcined, calcined, and deadburned gypsum. Products vary from raw, ground gypsum used for agriculture, to high-value-added industrial plasters, cements, and fillers produced from calcined gypsum. A sampling of the many products manufactured from Oklahoma gypsumincludes: (1) agricultural-soil amendment; carrier for insecticides, pesticides, and herbicides; calcium supplement in animal feeds; (2) gypsum wallboard-common, fire-resistant, and water-resistant varieties; (3) industrialgypsum plasters-art and casting, pottery and ceramic, molding and tooling, crayons, wall patching; (4) industrial gypsum cements-oil-well cement, high-strength statuary, high-strength tooling, fiber-reinforced architectural, road and bridge repair; (5) food and pharmaceutical-filler and binder in aspirin and other medicines, yeast activator in brewing of beer, moisture absorbent in bread and pizza dough; and (6)portland-cement retarder-ground with clinker to control setting time.

Jan 1, 1999

By Walter R. Curtner

Many, if not most, of today's pollution liability claims are related to events ("occurrences") that happened in the past. This fact creates an opportunity to obtain a large amount of insurance coverage at essentially no cost. Furthermore, in many cases, this insurance coverage is readily available. Scenario #1 For some 15 years, an underground gas tank has had a slow leak. The leak has now been discovered because the gas has contaminated nearby wells. As a result, an expensive $1 million cleanup is required. In addition, a liability suit has been filed for damages due to the contamination of nearby wells. Consequently, legal expenses are being incurred. Are all of these actual and potential costs insured? Obviously, if you have a pollution liability policy in place, the above costs will probably be insured. I say probably because business liability policies are not uniform. But, what if you don't have a pollution liability policy and what if your current general liability policy excludes all pollution liability (as most of them do today)? Under these circumstances, it first appears there is no insurance for this $1 million cleanup and liability suit. But this is probably not the case. You may well have insurance coverage, and you may well have much more insurance coverage than you ever expected. And, the insurance that I'm referring to is already in place. You simply need to find it and learn how to use this insurance - I'm referring to your old policies. In many cases, old liability insurance policies provide coverage for claims made today, because these policies were written on an "occurrence" basis of coverage. In fact, most still are written this way. This means that the insurance policy covers bodily injury or property damage liabilities (as defined in the policy) arising out of' "occurrences" or accidents that happen during the policy period regardless of' when the claim for damages is made. Therefore, for insurance purposes, the key question is: when did the "occurrence" take place? If someone falls and breaks a leg, that is clearly an "occurrence." The broken leg occurrence is, therefore, insured by the liability policy that was in existence at the time of the fall - regardless of when the claim or suit is filed, if ever. However, the answer to this question is seldom an easy one when you are looking at a pollution claim. In our scenario, the tank had a slow leak over 15 years, but property damage was not discovered until now. The question of when the "occurrence" (as defined in the insurance policy) took place has been litigated and continues to be litigated in many courts across the country. But, most often the answer has been that, for insurance purposes, the "occurrence" is the entire period that the tank was leaking (15 years), even though the contamination to the water was not discovered until 1987. This means that the person or company that is insured can potentially use all of its general liability policies (if they are "occurrence" policies, and most were), which were purchased during the 15 years from 1972 until 1987. And, these policies will potentially insure all of the claims and related exposures that arise out of this leaky underground gas tank. Scenario #2 In our first scenario, the claims and expenses were insured by past general liability policies because the claims arose out of events in the past, which, in turn, caused damage. Let's look at another example. In this scenario, Company XYZ has received a request to help clean up a landfill site because 10 years ago, XYZ dumped some toxic substances at the site, which was totally legal at the time. XYZ has not dumped anything at the site since this time. Nevertheless, XYZ is now being required to contribute $2 million to the cleanup of this site. In this scenario, if you had purchased "occurrence" general liability policies 10 years ago, these 1977 policies would (potentially) apply to the current $2 million cleanup claim. And, the reason is that the "occurrence" leading to the 1987 claim took place in 1977.

Jan 10, 1987

By A. Adu-Acheampong

The Mid-Tennessee Zinc (MTZ) mines, comprised of the Gordonsville, Elmwood, and Cumberland sites, last operated 4 years ago and are undergoing rehabilitation to begin production in 2008. The mines utilize a random room-and-pillar mining method that results in complex ventilation networks. Upon decommissioning, the mechanical ventilation units were removed and disposed of and several shafts sealed. In an effort to re-open the mines and operate in compliance with imminent Mine Safety Health and Administration (MSHA) diesel particulate matter (DPM) regulatory limits of 160TC µg/m3, a new ventilation system was required. The new ventilation system was developed primarily based on the diesel equipment required to meet production. Particular emphasis was placed on the DPM, diesel equipment utilization, main fan sizing, and fan locations to enable the mines to meet MSHA?s ventilation requirements in a cost efficient manner.

Jan 1, 2009

By B. T. Lusk, Q. Q. Huang, R. Q. Honaker, K. A. Perry

Rock dust is applied in underground coal mines to prevent the propagation of coal dust explosions. It is applied either dry or wet. Both methods have advantages and disadvantages, but the formation of caked rock dust particles is cited as a significant concern for wet applications. We conducted a study to evaluate the effect of modifying the rock dust particle surfaces to repel water and each other by the addition of oleic acid and sodium oleate. At a sodium oleate dosage of 1 kg/t, a contact angle of 112o was measured, indicating strong surface hydrophobicity and thus the ability to repel water. Fourier transform infrared spectroscopy (FTIR) studies indicated a chemisorption mechanism, which is necessary for long-term stability of the surface modification. The dispersibility of the modified rock dust samples was elevated by the application of both oleic acid and sodium oleate, thereby indicating a significant reduction or elimination of the detrimental effect of caking. Tests in an explosion chamber showed an 82.8 percent reduction in the dust explosion potential relative to untreated rock test applied by the wet technique.

Jan 1, 2015

By Kefton H. Teague

Olivine was first described and named by Warner in 1790. It is an olive green to greenish gray colored magnesium-iron silicate containing a mixture, in solid solution, of fosterite (Mg2SiO4) and fayalite (Fe2SiO4). Ratios between fosterite and fayalite in olivine are somewhat variable, but in general olivine contains at least 85% fosterite. Specific gravity is variable also, depending on the ratios of fosterite to fayalite. As a rule it is in the 3.2 - 3.4 range. All commercial olivine is obtained from the rock dunite, the most basic member of the peridotite group. Dunites, in addition to being composed primarily of olivine, generally contain assessory pyroxenes and spinels (chromite and magnetite). Dunites', when altered by hydrothermal solutions or metamorphism, often contain alteration minerals such as talc, serpentine, chlorite, vermiculite and amphiboles. In the 1930's and 40's considerable research was conducted on olivine for use as a refractory, plant food raw material, magnesium source for metal, and a source for magnesium chemicals. This research met with only limited success.

Jan 1, 1977

By B. Petkof

Olivine has been an accepted industrial mineral for the last 50 years. Its initial acceptance was based on the recognition of its refractory properties by European research workers in the middle to late 1920's. Initial U.S. olivine production began in the early 1930's in North Carolina and continues there today. Olivine also is produced in the State of Washington and in other countries.

Jan 1, 1982

By J. W. Currier

The compositions and natures of the materials charged to a blast furnace, as well as their respective distributions within the furnace, are known to int1uence furnace performance. However, fifteen years ago, there was little reason to believe that any significant variation of these parameters had been overlooked. Nor was there any particular reason to believe that olivine might be a particularly useful raw material for blast furnace applications.

Jan 1, 1989

By W. E. Lamont

As part of its program to minimize mineral and metal needs, the Federal Bureau of Mines conducted investigations to determine the feasibility of producing foundry-sand-grade olivine concentrates from low-grade sources. Using a Bureau-patented attrition-grinding technique, concentrates meeting Steel Founder's Society of America (SFSA) specifications for loss on ignition (LOI) were prepared. Studies showed that green strengths and tensile strengths of the attrition-ground olivine were equivalent or superior to those of commercial materials. Metal-casting studies showed that molds of attrition-ground olivine produced better surface finishes. The improved surface finishes were attributed in part to increased grain sphericity.

Jan 1, 1977

By Didem Maral

Olivine is a name of a mineral group that has a chemical formula of: (Mg, Fe), SiO4. The most important rock for the olivine group minerals is dunite, which can contain olivine up to 95-99%. Dunite can be obtained from chrome enrichment as a by-product. As a result of alteration of the olivine group minerals, several kinds of different minerals can occur. Main consumption areas of olivine are steel and iron industry. Also olivine is used in not only casting and refractory industries but also production of radiator, ballast material and abrasive. North of Bursa-Orhaneli has got more than 5 billion tons reserves in ultrabasic massifs. M.T.A found that olivine has got high quality of using in refractory and casting industry.

Jan 1, 2005

By Jr. Smith

Industrial minerals are just other rocks, except for the unique characteristics that make them useful in an industrial process. There is not a ready market for this type mineral and one or more uses must be developed to sustain production. The name "olivine" is a generic term used to indicate a group of orthosilicate minerals in a solid solution series, with forsterite (Mg2SiO4) and fayalite (Fe2SiO4) as endpoints. Since neither is found alone in nature, the mineral is always a combination of the two. The commercial deposits are high in magnesium and on the high end of the melting scale in the series. The name comes from the olive-green color.

Jan 1, 1992

By Robert J. Henning

The term olivine was first used in 1790 by J. Werner, and the corresponding mineral was so named because of its olive-green color (Hunter, 1941). Olivine is the principal component of the rock known as dunite. While by classic definition dunite is composed of 90% or more olivine, commercial use of these terms has resulted in more specific definitions. Commercially, the term olivine is used to designate a material that consists of 85% or more forsterite and contains 45 to 50% MgO, 39 to 42% SiO2, 5 to 8% Fe2O3, and has an ignition loss (LOI) of 1 to 2%. The term dunite designates a rock that contains 36 to 45% MgO, 36 to 39% SiO2, and has an ignition loss of as much as 10% (Teague, 1983). GEOLOGY Olivine is found in basic igneous and basic metamorphic rocks whose age varies from pre-Ordovician to Tertiary. Economic deposits are of magmatic origin and are restricted to the dunite variety of the peridotite group of ultrabasic igneous rocks. Olivine also occurs in basic igneous rocks such as gabbro, basalt, and diabase and more rarely as an accessory mineral in granite and metamorphosed crystalline limestones. Mineralogy The term olivine refers to a group of orthosilicate minerals in isomorphous series with magnesium-rich forsterite (Mg2Si04) as one end member and iron-rich fayalite (Fe,SiO,) as the other. In most olivines the ratio of magnesium to iron varies from 16: 1 to 2: 1. Commercial olivine deposits contain a mixture of forsterite and fayalite with the fayalite content restricted to less than 15% (Reed, 1959; Teague, 1983). Accessory constituents may include primary minerals such as ilmenite, magnetite, diopside, chromite, and garnet and secondary minerals such as chlorite, serpentine, talc, and vermiculite as alteration products. Chemical and Physical Properties The chemical composition of olivine can be expressed as either (Mg, Fe), SiO, or 2(Mg, Fe)O.SiO,. Table 1 presents chemical analyses for some commercial olivines. The physical properties of olivine are shown in Table 2. Distribution of Major Deposits Commercial olivine and dunite deposits are found in Norway, Japan, Spain, India, Italy, the United States, Sweden, Austria, Pakistan, and Mexico. Noncommercial deposits have been reported in New Zealand, Zimbabwe, South Africa, New Caledonia, Greece, Brazil, and Canada (Teague, 1983). The present markets for olivine are characterized by low unit value, high volume, and high sensitivity to freight costs, so few deposits are commercially viable. Literature from the USSR indicates that considerable research on olivine refractories is being done. (Afansa'ev, 1988), lending credibility to the conjecture that commercial deposits are being mined there. In eastern Canada synthetic olivine is being produced by calcining chrysotile asbestos mine tailings. In the United States numerous lenses of olivine extend in a belt from northeast Georgia northeastward across western North Carolina. Total reserves in North Carolina and Georgia are estimated at between 125 and 200 Mt. The largest US deposit is Twin Sisters Mountain, located in Whatcom and Skagit Counties in the state of Washington. This deposit, which has an outcrop area of 93 km2 and a relief of about 1 525 m. is estimated to contain 1 800 Mt of fresh, unaltered olivine (Teague, 1983). In addition, the US Bureau of Mines reports reserves of 50 Mt on Cypress Island in the state of Washington, and the literature reports eight complexes in southeastern Alaska, some containing cores of olivine as large as 1.6 km in diameter (Taylor, Jr., 1967). The world's largest deposit of olivine occurs in the Aaheim area of Norway, where reserves are estimated at a 2 000 Mt. Several other Norwegian deposits contain as much as 5 Mt each. In Japan the production of ultrabasic rocks is currently about 6 Mtpy, but the bulk of this output is serpentinite. Olivineldunite accounts for only 17% of this production. The major olivine deposit in Japan is located at Horoman Hill on the northern island of Hokkaido. Reserves at this deposit are estimated at 100 Mt (Anon., 1990). Spain is one of the largest producers of dunite. Reserves in the La Coruna District in northwestern Spain are estimated at 100 Mt. India, also a major dunite producer, has a large deposit at Salem in Tamil Nadu. In Italy olivine/dunite is mined from a deposit near Turin. In Sweden the largest deposit is at Arutats and is reported to be comparable in size to the Twin Sisters deposit in the United States. At present the only production in Sweden is from a deposit 30 km south of the town of Gallivare. Reserves at this deposit are reported to be between 1 and 2 Mt. Other significant deposits are: 1) in Austria at St. Stefan near Leoben, 2) in the Swat District of the North West Frontier Province in Pakistan, and 3) in Mexico at Cuidad Victoria in Tamaulipas (Anon., 1990).

Jan 1, 1994

Canadian mining giant Teck Resources Ltd. will be the exclusive supplier of the metals used in the production of the more than 1,000 medals to be awarded at the Vancouver 2010 Olympic and Paralympic Winter Games. Teck, the diversified resource company headquartered in Vancouver, B.C., is providing 2.05 kg (4.5 lbs) of gold, 1,950 kg (4,300 lbs) of silver and 903 kg (2,000 lbs) of copper sourced from its operations around the world. In addition to the raw materials mines, this year?s medals will make Olympic history as they will be the first to contain metals recovered from processing the circuit boards from end-of-life electronics (e-waste) that would have otherwise been destined for a landfill. After mining or production through a variety of smelting and recovery processes, each metal has been refined to enhance the metal purity.

Jan 1, 2010

By R. Fernando

"The Office of Mine Safety and Health Research (NIOSH-OMSHR) currently is leading an effort in the development of the next-generation self-escape apparatus as part of the research imperative directed by the MINER Act of 2006. A multifaceted contract program over the past 3 years delivered key components and base breathing modules to form the basis for developing backpack and vest-style versions of dockable self-contained (closed-circuit) self-escape respirators with hoods (CCMERs). This paper outlines the current status in developing the CCMER that incorporates a docking and switch-over valve (DSOV) for seamless transfer from one breathing device to another, and a hood with an inner mask and speech diaphragm (HMC) for ease of donning, ease of use, and communication ability. Three versions of the CCMER are being pursued, namely: the CCMER-B, which can be worn as a backpack and incorporates the features of a miner’s belt; the CCMER-V, which is worn similar to a miner’s vest and attaches to a miner’s belt; and the CCMER-C, a breathing module cached along the escape route that can be docked to the -B and -V versions. Human factors considerations are a key element in the CCMER design, as it is to be continually worn by the miner while underground, and must be readily accessible for deployment when needed. The CCMERs are designed to be capable of being certified to 42 CFR part 84 standards, including sub-part O for mine use, and to meet MSHA permissibility regulations for use in underground mines. They are sized for sufficient oxygen capacities (Cap 2 and Cap 3 as defined in sub-part O) to yield a duration that is of practical use in a mine escape scenario. INTRODUCTION The National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) is leading the development of self-escape apparatuses to provide breathing gas to mining personnel operating in the event of an emergency in various capacities underground in environments containing hazardous gas components. The Mine Improvement and New Emergency Response Act of 2006 (also known as the MINER Act) and input from the mining community called for the need to move Self-Contained Self-Rescuer (SCSR) technology to a next-generation status. In response to this need, NIOSH’s Office of Mine Safety and Health Research (OMSHR) established a strategic plan to develop key components and devices with help from external experts knowledgeable in breathing apparatus designs. The US Navy was identified as a key expert in this field through its extensive experience in diving apparatus and life support systems, and development work commenced through Inter-Agency Agreements with OMSHR. A contracts program was also launched with industry experts specializing in this field. This paper outlines the current status in developing the Next-Generation Closed-Circuit Mine Escape Respirators (CCMERs) that could be used for surviving and escaping from a mine following an emergency that renders the mine atmosphere irrespirable."

Jan 1, 2016

By Waclaw Trutwin

The idea of automatic or remote control of the mine ventilation process generally, and methane concentration particularly, attracts the attention of mining engineers more and more. The advantages of introducing mine ventilation control systems are breaking traditional reluctance. The change of attitude is not only because of the requirements of modern exploitation technology, but it is also due to the recent progress in development and successful introduction of reliable monitoring systems and actuators in the form of controlled ventilators and doors [1]; [2], [3], [4], [5], [6]. Many 'years of theoretical and experimental studies of the dynamics of mine ventilation processes created the needed base for a proper design of an automatic control system [7],[8],[9], [10]. From these studies must, however, be drawn a fundamental conclusion, which may be regarded as the motto of this paper: An automatic control system for mine ventilation ill-conditioned or improperly designed is capable of creating hazard situations in response to random disturbances, much more, severe in consequence than a traditional ventilation system without any automatic or remote control! This statement is easy to prove if the dynamic properties of the ventilation process are taken into consideration. The ventilation process, as a matter of fact, is described by non-linear equations, and it must be expected that the process has more than one state of equilibrium. In other words, in the ventilation process may exist not only one but also more than one steady-states of flow, of which some are stable and others unstable. In certain circumstances, there may be no steady-state at all, and the process will oscillate [8], [11] , [12] . The state of flow in a network tends towards a steady-state and the actual steady-state established will depend on the initial conditions or disturbances in flow (fire,. etc.), which steady-state from the total number that will be . We frequently observe jumps from one steady-state to another. Disturbances in flow conditions which may cause such transitions are events of random character, occurring very rarely. Concluding, it must be stressed that there has to be a control system adjusted to the ventilation process in order to avoid situations mentioned above. There is only one alternative available and suitable for examination or study of the dynamics of a given mine ventilation problem: either by continuous monitoring of the real process, or numerical simulation of the process using a mathematical model. The advantages of the second method are obvious. This method allows consideration of every possible case very quickly and cheaply in relation to the first method. The aim of the paper is to show again that the simulation of the mine ventilation process and particularly a methane concentration process, separately or combined together with a control system, are real possibilities. A simulation method requires precise specification of the problem under consideration. For example, if we intend to examine a methane-concentration control system, the following items have to be specified: - expected target function of the control system. - structure of the control system. - mathematical model of control system, including sensor system, data preparation system, controllers, decision routine, regulators, etc. - structure of mine ventilation network. - mathematical model of ventilation process, including air flow and methane concentration processes. - pattern of disturbances which may occur in the controlled process as well as initial conditions on a 'start-up' of the system. Using typical computer programs for numerical solution of equations in the mathematical model of the problem involved, we are able, within the adequacy of the model, to simulate every case specified by the disturbances and initial conditions. As a result of simulation, it is expected that the following parameters could be defined: - transient flow in the network. - transient state of methane concentration in working areas. - stability of flow and methane concent¬ration. - stability of the control system. - range of control. - efficiency of control, etc. It is obvious that simulation methods readily allow for modifications to existing systems such that desired results will be obtained. Also optimisation problems could be solved by use of the simulation methods. In order to illustrate these general thoughts, a brief presentation of a mathematical model of methane concentration and

Jan 1, 1980

By D. W. Fuerstenau, J. Vazquez-Favela

This paper shows how the efficiencies of size-reduction processes depend on the mode of particle constraint and energy transfer within the comminution device: namely, whether the process consists of single-particle loading, confined-particle-bed comminution or loose- (unconstrained-) particle grinding. The relative efficiency of single-particle comminution, ball-mill grinding and particle-bed comminution in the recently invented high-pressure roll mill is evaluated by making use of the self-preserving nature of the size distributions of comminuted products. The highest energy efficiency can be achieved by utilizing a hybrid two-stage system in which the material is first ground in the high-pressure roll mill and then the ball mill.

Jan 1, 1998

By S. Yap, F. J. Sotillo, L. P. Irwin, F. M. Utsey

Slimes, especially clays, are detrimental to several processes in the Mining Industry. The efficiency of classification, clarification, gravity separation, and flotation decreases significantly in the presence of slimes and clays. This problem is particularly critical in the Phosphate and Sulfide Industries. To reduce the effect of slimes in mineral processing, several desliming techniques and chemical additives are used, such as sodium silicate, sodium carbonate, sulfuric acid, tripolyphosphate, hexameta phosphate, etc. Lately, the Mining Chemical industry has shift to more “Specifically Developed” reagents that offer the most efficient and cost effective performance, mainly using organic polymers. For this purpose, the Mining Chemical Industry needs to understand the crystal chemistry of minerals, the chemistry of the aqueous media, the interactions in solids-aqueous-gas interfaces, the rheology of the system, and the plant operation conditions and parameters. This paper describes the use of surface chemistry fundamentals on the design of an organic polymer capable of modifying the rheology of clayish slurries of a phosphate ore. The change in the rheological characteristics of the clayish phosphate slurries allow fine ore particles to settle faster by reducing the slurry viscosity. Thus, abetter separation of the ore from the slimes is possible using gravitational or centrifugal forces. As examples of the application of this reagent, industrial and pilot plant tests on desliming using tanks and hydrocyclones are presented. These tests showed the reduction of 32%-36% in ore losses for different phosphate ores during desliming operations, and the increase of cyclones desliming efficiency to 80%. Tests were also carried out to improve the rejection of unwanted iron bearing slimes in phosphate feed. These tests demonstrated that it is possible to reduce by 0.25%-1.23% Fe2O3content in the flotation feed product. As a result, significant economical benefits are observed with the use of this new technology without any adverse effect on down stream operations, such as clay settling or phosphate flotation.

Jan 1, 2003

By James Wm. White

Mine management now recognizes the value of computer-based truck-shovel dispatching in open pit mines. The key tangible benefits are substantial productivity increases with a given fleet of equipment or, alternately, significant reductions in equipment required to meet production quotas. In this work, we review the literature, report on efficient, optimal algorithms for haul truck dispatching in real-time, and briefly discuss methods used by various mines to evaluate productivity improvements over manual methods. We also present actual results obtained at thirteen mining operations around the world.

Jan 1, 1992