Search Documents

By L. Adler

Existing classifications of mining and construction equipment have had major deficiencies. They often lack organization, balance, and have remained obscure. Particularly when proceeding to great.er resolution these deficiencies have proven crippling. By adopting "Classes", "Groups" f "Types" and "Kinds" at successive degrees of refinement, a "Taxonomy" is developed based on clear visual differentiation or on a "Morphology??. This symbiotic application, adopted from the Biological Sciences, yields clear, simple and unambiguous results. Supporting this effort are guidelines for easily and credibly sketching equipment which are also distinctive. Numerous illustrative examples are provided. Communications are improved and the engineer obtains a confident feel for the equipment at hand.

Jan 1, 1989

By David Marsh, Mark W. Johns

Carbon-in-pulp (CIP) is a preferred method of gold recovery from cyanided pulp. However, the resin-in-pulp (RIP) process is considered to have several advantages for the recovery of gold. Mintek therefore undertook a research programme to develop a commercially-viable RIP process. The MINRIP RIP process and a novel gold­selective strong-base resin, Minix, were developed. The process has been successfully demonstrated at a scale of 100 000 t/month. Continuous countercurrent tests using synthetic solutions indicate that the relative performance of an adsorbent depends on the composition of the solution. Minix resin yielded a higher gold loading than that of carbon, while maintaining an acceptable barren value. Batch tests on a number of gold-bearing materials indicated that Minix has potentially a higher capacity than carbon, and loads gold faster than carbon. An economic appraisal that consolidated the countercurrent results and the economic study indicated that the capital and operating costs of the Minrip process are considerably lower than those of CIP. The amount of the cost advantage depends on the gold content of the feed and the throughput.

Jan 1, 1993

By Richard E. Hucko

The Coal Preparation Division of the Pittsburgh Mining Technology Center conducted an investigation to assess and compare the pyritic sulfur reduction potential of coal-pyrite flotation and high-gradient magnetic separation (HGMS). Tests were run on three coals--an Upper Freeport bed coal, a Lower Kittanning bed coal, and a Pittsburgh bed coal--to establish grade- recovery relationships characteristic of both processes. Representative portions of each coal sample were crushed to two top sizes--nominal minus 35 mesh (0.5 mm) and nominal minus 100 mesh (0.149 mm)--and subjected to conventional froth flotation. The froth product was then beneficiated by coal-pyrite flotation or HCMS to provide a direct technical comparison of the two processes. At minus 35 mesh (0.5 mm), the size normally employed for coal flotation, both coal-pyrite flotation and HGMS effectively separated pyrite from coal, and the performance of the two processes was essentially the same. At a size of minus 100 mesh (0.149 mm) , however, the performance of HGMS exceeded that of coal- pyrite flotation. The separations effected by HGMS were more efficient at minus 100 mesh (0.149 mm) than at minus 35 mesh (0.5 mm). On the other hand, it was concluded that either the effectiveness of coal-pyrite flotation decreases with diminishing top size, or the process has not been optimized to treat material finer than 35 mesh (0.5 mm).

Jan 1, 1981

By Gerrit V. R. Goodman, Charles D. Taylor

A technique was developed to determine the fraction of air recirculated from the scrubber exhaust toward the face and the fraction of gas captured by the scrubber. To determine these two values, a series of tests was required. In the first test, gas was released at the face area and concentrations measured at the scrubber exhaust. In the second test, gas was released directly into the scrubber with concentrations again measured in the scrubber exhaust. The simultaneous solution of two independent flow expressions gave values of recirculation and scrubber capture. A series of tests was conducted with various combinations of scrubber flow, curtain flow, setback distance, and machine location. Statistical analyses then were conducted to determine those factors which influenced the levels of scrubber recirculation and scrubber capture in a deep cut. INTRODUCTION As cutting depths increase, the trend is toward the use of blowing face ventilation systems. With these ventilation systems, the potential exists for recirculation between the scrubber exhaust and the intake air stream. One concern is that methane gas, having been removed from the face area, is subsequently recirculated back into the intake airflow. Under these conditions, methane-laden air could be substituted for fresh intake air, leading to increased methane concentrations at the face. There is currently no standard for recirculation between the scrubber and intake airflows. The implied understanding of the Mine Safety and Health Administration (MSHA) is, and has always been, that any recirculation of ventilation air is unacceptable. To minimize recirculation potential, MSHA suggests that operators maintain scrubber and curtain flows within 0.47 m3/sec (1000 cfm) of each other. Given that recirculation may occur in some circumstances, the question arises as to how much recirculation constitutes a hazard for the face workers. Unfortunately, there is currently insufficient information to answer this. Emphasis must instead be placed on means to quantify the amount of recirculation between the scrubber and face area. Methods must also be examined to control this phenomenon. This paper presents a technique for quantifying recirculation and scrubber capture levels in a blowing face ventilation system. Several ventilation parameters are investigated to determine their effects on these levels. DEVELOPMENT OF RECIRCULATION EXPRESSIONS One way to measure airflow quantities at a point near the face would be to measure the gas flow rate Qgas, and gas concentration c at that location. The airflow Qair, would be simply the ratio of these two values, Qair, = Qgas/c. Although gas concentration values, c, can be obtained easily with existing gas monitoring equipment, it is more difficult to obtain gas flow readings, Qgas, at specific locations. To obtain these values of Qgas, another method was needed. Previous work in this area was conducted by Kissell and Bielicki (1975). However, the calculations in their model assumed a constant gas concentration in the region around the continuous miner. In a deep cut, it is questionable that gas concentrations would remain constant or uniform around the mining machine. The technique presented here does not rely on this assumption. It instead assumes that the gas concentration in the scrubber exhaust remains constant. A quantity of gas released at the cutting face either flows into the scrubber inlets or bypasses the inlets and flows around the off-curtain side (in this example, the right side) of the continuous miner (Figure 1). The fraction of the face gas that flows

Jan 1, 1993

By Colonel Oattis E. Parks

The quantity of coal recovered by diamond coring techniques is not sufficient in many instances to make meaningful coking and/or ash fouling tests. Quantities in excess of that obtained by conventional coring techniques, usually in amounts exceeding 500 pounds, has been designated bulk sampling. During the past three years, AMAX Coal Company has utilized five methods of bulk sampling. It was our desire to obtain a bulk sample that was diagnostic of the seam by the most expedient and economical method. From the beginning all of our efforts have been directed to methods which would extract the required coal from slim boreholes which provide quick and inexpensive access to the coal seam, regardless of depth, terrain and accessability. In our efforts and investigation several large diameter cores have been taken from thick coal seams at relatively shallow depths in easily drilled rocks. On the other hand, for deeper thin seams multiple large diameter coring is more expensive and time consuming. It is somewhat less expensive when multiple cores are taken from a single slim borehole utilizing deflection coring, although considerable skill is necessary.

Jan 1, 1973

By W. W. Dudley

The U.S. Geological Survey, in support of underground testing of nuclear explosives, has developed a technique (Dudley, 1910) to predict the inflow of ground water to large underground chambers that are cylindrical in shape. By treating the chamber as a large-diameter well pumped at constant drawdown, the nonsteady discharge can be computed by the method of Hantush (1961) for analyzing flowing wells under leaky artesian conditions. In mining applications, whether for mineral recovery or for nuclear testing, the most serious departure from the conditions of Hantush's model results from the gradual enlargement of the opening under drained conditions. Inherent in the analytical technique is that the "well" is fully completed at the time that dewatering begins. Because safety is the prime concern, however, initial pumping systems or personnel evacuation procedures must be designed to handle the greatest conceivable inflow. DEFINITIONS Because somewhat different meanings are attached to similar words in different technical fields, the U.S. Geological Survey definitions (Lohman, 1970) of several hydrologic terms used in this report are given below. An aquifer is a formation, group of formations, or part of a formation that contains sufficient saturated permeable material to yield significant quantities of water to wells, and springs. A confining bed is a body of material lying stratigraphically adjacent to one or more aquifers and having a hydraulic conductivity distinctly lower than that of the aquifer. The total head (dimensions L) of a liquid at a given point is the sum of three components: (1) elevation head, he, which is equal to the elevation of the point above a datum; (2) pressure head, hp, which is the height of a column of static water that can be supported by the static pressure at the point; and (3) velocity head, hv, which is the height the kinetic energy of the liquid is

Jan 1, 1971

By John J. Dran

Large mining companies use a number of sophisticated analytical techniques for introducing the element of risk into the valuation of mineral reserve sites. These methods include, but are not limited to, sensitivity analysis, computer simulation, conditional probability, and portfolio theory. Such techniques enable the managements of these large companies to have an awareness of the many possible ramifications of their investment decisions. On the other hand, small mining companies and individuals in the mining business, due to limited financial and technical resources, still rely primarily on single point estimates of the value of mineral reserves. These small miners introduce the aspect of risk only through the application of an appropriate "speculative" discount rate. This paper illustrates the application of a technique for the introduction of risk into investment analysis. The method appears to be most suitable for use by small mining companies and individuals contemplating a large investment in a new mineral reserve site.

Jan 1, 1974

By Bruce M. Davis

The variogram is the function used to express the intercorrelation of a regionalized variable. It is used to quantify, for example, the natural variability of mineralization and in that sense may be thought of a average disimilarity between metal quantity at two points inside a deposit.2 As David2 explains, appropriate mathematical functions of distance and direction are used to characterize variograms, a process that he says is analogous to selecting a normal or lognormal model for an observed distribution. Methods for choosing a model for the underlying variogram of a random function based on the sample data appear in the literature.3,8 A crossvalidation procedure is available to check the validity of the model.3 However, statistical validation of the choice of the model through the mechanism of hypothesis testing is not presently available. In the section to follow, notation and background material is presented upon which a large sample test procedure will be constructed. The stationarity assumptions presented refer to covariance stationarity. A test procedure is then proposed, and an example is given for the case of the one dimensional random process.

Jan 1, 1979

By K. Taniguchi, Y. Inada

When underground openings are excavated in rock mass for storage of Liquefied Natural Gas, hereinafter referred to as L.N.G., as its temperature is -162o C, steep temperature gradients and thermal stress occur around the openings. That is, the plastic zone and cracks around openings will expand with time. In this paper, the range of cracks which were obtained by the Crack Analysis Method and the range of the plastic zone which was obtained by the No Tension Analysis Method were investigated and compared.

Jan 1, 1986

By A. Hayatdavoudi, E. Apande

Introduction Troublesome shales have plagued the petroleum industry for more than 50 years. Unstable boreholes have been experienced when drilled into shale formations; sane have been studied almost at the beginning of rotary drilling. A little progress has been made since then, but much is still to be learned. No simple solution exists so far, but good drilling practices combined with good mud practices have been helpful. It is well known that shales in general have a strong affinity for water, and when water is adsorbed, the stability of the shale section of a well is reduced; cohesive strength will be re- bed, properties will be altered and shale will generally expand and/or crumble. The amount of water a shale will adsorb depends on the characteristics of its clay mineral and the ionic concentration of surrounding fluid. Fluid loss and the resulting hydration of an unstable formation can lead to serious downhole problems. The rate of fluid loss depends greatly on the permeability of the deposited cake. In impermeable formations, however, there is no loss of fluid into the formation. As such, shale, because of its very low porosity and almost no permeability, could be termed impermeable. Yet there is strong evidence that shale surfaces are wetted by an invasion of fluid into the formation through microfractures and jointed planes. It is this wetting that causes the shales to swell and slough into the hole, resulting in problems such as increased mud volume and treating costs, bridges and fill-up, stuck pipe, overgauge hole, poor cement jobs and increased cement requirements, and logging and completion difficulties. Drilling operations have been defeated by severe shale problems, resulting in & hole being plugged and abandoned after several weeks of drilling. Shales are we1l known as being difficult and costly to drill. Numerous fishing jobs have plagued drilling operations, and the cost of reaming tight holes ad weighting up the drilling mud to control shale sloughing has been high. The concept of controlling water loss to stop sloughing was introduced in the 1920's. It was known-then that calcium in fresh water re- strains clay £ran excessive swelling (theory of osmosis) . This reinforced the belief that calcium-based muds such as lime, gypsum and calcium chloride should minimize hydration of clays. Lime muds were then introduced for this purpose and others in the 1930-1940 decade1. They were used for shale inhibition but were not effective. In an attempt to improve them, a special calcium-type mud beam popular during the 1950's. Hole enlargement continued and they too were considered ineffective. During & early 1960qs, papers were published claiming that shale swelling could be prevented by using high concentrations of chemical thinner called Chrane Lignosulfonate1. This began the era of highly treated lignosulfote muds. Unfortunately, the hole enlargement problem continued. During & mid-1960’s, oil based muds were used for the purpose of inhibition of shales. Not until 1966 did Mondshine2 suggest that the water phase be saturated with calcium chloride. The cost of using oil based mud was considered by most operators not worth the additional hole stability. The potassium chloride-polymer muds were also used in many fields in the United States and western Canada. The use of these muds has been claimed to prevent clay swelling by inhibition and encapsulation in sane areas of western Canada. They are also expensive and their ueneral application is still experimental. To reduce filtrate loss when sloughing shale becomes a problem during drilling is a reasonable practice. This study will investigate the use of cationic organic additives to mud to form a protective barrier between the shale - which are primarily composed of clays - and water that will keep water from entering the microfractures and will also prevent them from hydrating. In so doing, an understanding of modern clay chemistry and & dispersive properties of cationic additives in water based systems will be our most valuable tools. This study will also present and solve a mathematical model for simulating cation transport phenomena in fractured shales using the Framdlich equilibrium adsorption isotherm. The studies will analyze wellbore failure and stability as affected by cationic organic material.

Jan 1, 1986

By Dai Wang

Stoppings are necessary ventilation control devices for effective air distribution underground. However, one of the major problems underground mining has is that every stopping is a potential leaking source. Since air always flows from a point of high pressure to one of lower pressure, and the total pressure at every point in intake airways is higher than that in the return airways, air will always tend to leak from intake to return (Tien, 1996). In many mines, less than half of the air entering the mine actually gets to the working areas; the rest of it simply short-circuits directly to return airways through leaky stoppings instead (Timko and Thimons, 1983). Leakage through a stopping occurs because of pressure drops across the stopping and available leaky path in stoppings. Empirical equation has been widely used to characterize the relation the amount of leakage and variables that affect leakage. However the use of this equation requires accurate information for constants which are not always readily available. It is the attempt of this paper to derive an equation similar to the Atkinson Equation that can readily be applied to characterize pressure-leakage relationship for any given stopping.

Jan 1, 1998

By C. J. Hall

An investigation of multi-shaft airflow problems by the author in 1976 (1) was presented in the hope of arousing considerable written comment, but in fact-. only one contribution (2) was forthcoming. The investigation in this paper is taken several stages fur¬ther, because the matter is of major importance in many American hard rock mines with complex networks extending over thousands of meters vertically. The examples used have all been generated thermodynamical¬ly and checked by motive column (denisty) calculations. Dry air has been used to reduce the amount of time spent on the rather complex calculations, but it has been shown (3) that the principals developed apply equally well to air/vapor/water mixtures. Initially the subject is investigated using both thermodynamic and motive column analyses. The latter part of the paper concentrates on a motive column presentation. Both methods are, of course, equally valid and give identical answers to any situation when correctly applied, as is shown in the worked examples.

Jan 1, 1980

By M. Abdelkhalek, M. Hepworth, D. Tao, B. K. Parekh

Pre-combustion coal cleaning and post-combustion flue gas desulfurization (FGD) using lime or limestone are the primary methods employed to reduce sulfur dioxide (SO2) emission from coal combustion. These processes generate voluminous pyrite and gypsum solid wastes that are usually landfilled, occupying thousands of acres of land and creating serious land and water pollution problems due to the release of acids and toxic substances. An integrated process has been developed for the combined utilization of gypsum and pyrite wastes by converting them into useful products including lime, sulfur, and direct reduced iron (DRI). The process includes four major steps. The first step is to concentrate pyrite from coal preparation tailings using flotation or gravity separation. The second is the thermal decomposition of pyrite into pyrrhotite and sulfur. This is followed by the reduction of pyrrhotite with carbon in the presence of lime to produce iron and calcium sulfide. The fourth step involves the reaction of calcium sulfide with gypsum to produce lime. The chemical reactions involved in the process were studied using thermogravimetric analysis (TGA) and X-ray diffraction (XRD)techniques. Process variables studied included reaction temperature, time, reactant composition, and purity of reactants.

Jan 1, 2000

By A. Nivala, S. Ulgiati, M. Canino

Mining and processing of bastnaesite ore, (Ln)CO3F, for lanthanides extraction is investigated in this paper. This series of elements proved to be applicable for a wide range of high-tech uses. In spite of the strategic importance of lanthanides, no LCA and energy analyses of their extraction have ever been published. We perform in this paper a Life Cycle Assessment of the Lanthanide production cycle, based on available database and literature data from Mountain Pass mine (USA) and other worldwide mining and processing sites, most of which in China. We investigated three main steps: mining, milling (including transport, grinding and drying), and flotation (for lanthanide chloride extraction). We do not investigate here the separation of pure oxides from lanthanide chloride, a compound which is also marketed as such. The conventional LCA was integrated by means of energy and emergy evaluations, aimed at investigating respectively the global energy cost and the environmental sustainability of the process. Indicators of material intensity, thermodynamic efficiency, and environmental impact (including LCA and ecological footprint impact categories) are calculated and discussed.

Jan 1, 2005

By James J. Scott

Three dimensional photoelastic techniques have been developed which provide information on the state of stress at any point in a model investigated. This investigation utilizes these techniques to determine the stress distributions in the pillars and the roof of a room and pillar mine model. Castolite plastic was used for the construction of the model in which a stress pattern was developed by the stress freezing process. Analysis of the stress pattern was accomplished by use of data obtained by observing points in slices from the model with a polariscope and solving data obtained by' the shear-difference method. Slices through the centerline, edge of pillar and centerline of span were investigated. Results of this work provide information on the overall stress distribution on points of stress concentration in compression, shear and tension, show relative magnitude of stress throughout the model and indicate directions of the most important stress values. A generalized roof bolt pattern is developed for room and pillar mines based on the stress distribution. A digital computer was used in the reduction of data and proved to be extremely useful for investigation of this type.

Jan 1, 1963

By K. J. Stanaway

Environmental pressures on waste disposal are forcing pigment producers to use higher content TiO2 feedstocks with lower levels of trace elements. Despite this, 50% of the worlds TiO2 comes from ilmenite concentrates with only 37 -54 % TiO2 An industry growth rate of 25 % in the next ten years combined with trends to diminishing resources and lower grades for rutile (95 % TiO2) and leucoxenized ilmenite (55 to 90% TiO2) mean that unless new discoveries are made soon, the industry will become even more reliant on ilmenite. A hypothetical ideal feedstock is presented and strategies to obtain it are suggested. Reasons for some of the mineral specifications are given.

Jan 1, 1994

By Chee Theng

"What do you think are the most important topics in mineral processing today? It is a question that begs to be asked when more than 100 of some of the best and brightest in Colorado mineral processing and their invited guests are gathered in one room. They are there for the 66th Annual Colorado MPD Meeting held at The Broadmoor in Colorado Springs: three days of finely curated talks and social events where participation was strong, and information was exchanged and connections forged in a relaxed, informal atmosphere.Water, tailings and social licenseNot surprisingly, water management, with the associated issues of tailings and social license, was high on the minds of those present. The Mount Polley and Samarco tailings dam failures have had repercussions across the industry. “There are big challenges with respect to tailings, and social and environmental pressures to find better ways to treat them,” said Steve Hearn of Huntsman Corp., a view echoed by Bob Kilborn of Kilborn Group LLC. Metso Minerals director Keith Butler said, “Water conservation is a key issue today. Many mining activities are now located in remote areas, so it has social and economic impacts on mining operations.” For Brian Olson of Samuel Engineering, wastewater and reclaimed-water treatment is interesting.Fittingly, the first talk of the meeting was on dry stack tailings by Michael Blois of Takraf USA, who went over both the advantages and disadvantages. “The average now is over one tailings dam failure a year,” Blois said, “and that is one too many.” But the technology may not be the right fit for all projects. In his talk on the KSM project, Jay Layman, president and COO of Seabridge Gold, showed how it isn’t practical for KSM and how Seabridge reached the decision on a cyclone sand tailings managementfacility as the preferred management strategy.The luncheon keynote also dealt with a tailings pond spill, but of a different kind. Bob Schafer, chief executive of Eagle Mines Management, spoke on the federal missteps that led to the spill into the Animas River from the Gold King Mine, a mine that had been a dry mine throughout its life and up to the 1990s."

Jun 1, 2016

By J. Cheung, H. Rabia

The traditional methods for predicting mine air temperatures are based on steady state heat transfer models as developed by Voss (1969) and Starfield (1983). These models are useful in providing approximate predictions of air temperatures in trunk and gate roadways. More complex models are required to provide predictions along faces. In practice, the heat flow in underground mines is of transient nature and recent observations in some British Coal mines show temperature variations of up to 5°C during a working week at any one point. In addition, the recent introduction of district recirculation of mine air in British mines requires a more precise prediction of air temperatures during start up of the system or during breakdown. A transient heat transfer theory based on the work of Jordon is presented. The method lends itself easily to computers due to the large number of calculations involved. The proposed transient model is validated using actual temperature data collected in roadways in Wearmouth Colliery in the North East of England. The transient results are compared with the steady state predictions of Voss (1969). Finally, predictions of air temperature in roadways for a recirculation system will be made using both the transient and steady state models. Temperature predictions along faces will be made using a separate model.

Jan 1, 1989

By A. W. Storm

Vertical shaft furnace design and operation have their roots deep in antiquity. There is substantial evidence to indicate that iron was reduced from its oxides to serve mankind's needs long before recorded civilization - - actually prior to 3500 B .C. For at least 5500 years man has been matching wits with Nature to find better methods of extracting this most common, yet essential, metal from her, grasp. And, during nearly all of this period, the vertical shaft furnace has played a principle role in this dramatic struggle.

Jan 1, 1962

By C. V. Trang, V. T. Le, K. Enns, J. J. Byerley

The precipitation characteristics of copper and nickel cyanides from solutions continuing copper zinc and nickel cyano complexes are examined. Equilibrium precipitation calculations are presented as well as comparative experimental data. The practical significance of the precipitation data is discussed in the co·ntext of an initial step m an overall treatment strategy for mixed cyanide effluents.

Jan 1, 1998