Search Documents

By Morgan M. Sears, Gamal Rashed, Michael M. Murphy, Brent Slaker

A parametric study was conducted using FLAC3D numerical models to examine the impact of oblique loading on the strength and yield pattern of a stone pillar using two simplified geometry types. In type-1 the side walls of the pillars were assumed to be perpendicular to the roof and the floor, while in type-2 the side walls were assumed to be vertical. These two geometries are frequently used to simplify/model the creation of pillars in dipping mines. Results from the numerical modeling indicate that dipping pillars have reduced strength compared to horizontal pillars, and they are at an elevated risk of failure. Also, an asymmetric failure propagation pattern could be obtained depending on the interaction between the pillar width/height (W/H) ratio, seam dip, in situ stresses and pillar geometry.

By Y. H. Cheng, H. EI-shall, S. Gupta, N. A. Abdel-Khalek

A 14.6 cm (5.75 in.) diameter by 1.83 m (6 ft) tall laboratory-size column is used in flotation of Florida phosphates of different feed sizes. In this paper, the effects of different parameters on the flotation efficiency of coarse particles (belt feed, -1.4 + 0.5 mm, i.e., 14 x 35 mesh) under negative bias are discussed. Parameters included collector dosage, frother type and dosage, and conditioning water, which contained a residual concentration of collector. Flotation tests were performed using statistical designs. The results strongly suggest that flotation performance is dependent on the used combination of reagents. Interactions between frothers and the collector and, consequently, the flotation efficiency were found to be dependent on frother type and presence or absence of conditioning water. Under the negative bias, an excellent recovery of more than 98% of phosphate was achieved in concentrates of high grade (above 31% P205) from such feed of coarse particles.

Jan 1, 1999

A parametric study was conducted to establish the optimum operating conditions for the column flotation of fine coal. The parameters examined in this investigation included collector and frother dosages, feed solids content, and the volumetric flow rates of feed slurry, air and wash water. Despite the wide range of conditions studied the experimental data were found to fall along single grade-recovery curves, just below the maximum separation predicted by the release analysis technique. The deviation of the parametric test data from the release curve was attributed to the nonselective entrainment of mineral matter associated with poor froth washing. The operating point on the characteristic recovery-grade curve was found to be primarily determined by feed rate and aeration rate.

Jan 1, 1992

By Randal J. Barnes

The nonlinear network optimization algorithm developed in this paper solves the following mine ventilation design problem: find the location and size of all fans and regulators which minimize the overall system power consumption while satisfying all physical, legal, and operational constraints. This work includes the formulation of the problem within the framework of mathematical optimization, the development of the computational theory, and the creation of an efficient solution methodology. The algorithm has been implemented on a microcomputer, and a small but representative example is included. The algorithm presented in this paper has four limitations. First, the optimization process is for a single point in time: the dynamic nature of a mine ventilation system in an evolving mine is not directly addressed. Second, the topology of the ventilation network is required input information. The mathematical algorithm does not optimize the size or location of the mine ventilation airways; however, the post optimality analysis techniques can be used to aid in topological decisions. Third, the problem is formulated using volumetric flow; thus, heat and moisture transfer are ignored. Fourth, the capital cost of ventilation equipment is not included in the formulation.

Jan 1, 1989

By M. R. Yenchek

Faulty insulators on mine trolley/track haulageways may allow the flow of leakage currents into the mine roof and ultimately result in combustion of the local roof material. The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory (PRL), has devised a passive means to detect overheating insulators on direct current systems. The detector consists of a spring-loaded cartridge that ejects a reflective streamer of white Teflon tape when subjected to elevated temperatures. The cartridge assembly can be easily installed over the outer metallic shell of an existing trolley line insulator. If an insulator overheats due to ground leakage currents, the visible streamer alerts mine personnel traveling on the haulageway.

Jan 1, 1998

By Yao Zhou

Under the United Nations Convention on the Law of the Sea (UNCLOS), the international seabed area (Area) and its resources are the common heritage of humanity (CHH). Patent rights can be incompatible with the CHH doctrine and its underlying principles because patent holders might charge unjustifiably high prices to license patented technology for exploring and exploiting the Area’s resources (creating a "patent holdup" situation), might choose not to license, or might license exclusively when doing so would contravene CHH principles. However, a reasonable patent licensing regime can contribute to sharing the benefits derived from the Area and promote environmental sustainability. Provisions of the UNCLOS that stipulated compulsory technology and financial transfers were removed in the 1994 Agreement relating to the Implementation of Part XI of the UNCLOS (1994 Agreement), but to promote equity and sustainability I propose a voluntary licensing regime modeled on the concept of reasonable and non-discriminatory patent licensing (RAND) that has been used in other contexts. The International Seabed Authority (ISA) or another entity will need to coordinate and promote this licensing regime through governance of intellectual property (IP) derived from the Area. This proposed approach can better effectuate the CHH doctrine and its underlying principles.

Sep 1, 2014

By Yao Zhou

Under the United Nations Convention on the Law of the Sea (UNCLOS), the international seabed area (Area) and its resources are the common heritage of humanity (CHH). Patent rights can be incompatible with the CHH doctrine and its underlying principles because patent holders might charge unjustifiably high prices to license patented technology for exploring and exploiting the Area’s resources (creating a "patent holdup" situation), might choose not to license, or might license exclusively when doing so would contravene CHH principles. However, a reasonable patent licensing regime can contribute to sharing the benefits derived from the Area and promote environmental sustainability. Provisions of the UNCLOS that stipulated compulsory technology and financial transfers were removed in the 1994 Agreement relating to the Implementation of Part XI of the UNCLOS but to promote equity and sustainability I propose a voluntary licensing regime modeled on the concept of reasonable and non-discriminatory patent licensing that has been used in other contexts. The International Seabed Authority or another entity will need to coordinate and promote this licensing regime through governance of intellectual property derived from the Area. This proposed approach can better effectuate the CHH doctrine and its underlying principles.

Sep 1, 2014

By R. L. Unger

Restricted fields of vision are a common problem with underground mining equipment. Also, when lighting systems are provided, they may be positioned where they cause glare. This restricts the visibility around the machines even further. To help address these problems, the U.S. Bureau of Mines has developed a PC based software package to aid in the analysis of certain human engineering aspects of mining equipment design. The software is available for use by equipment manufacturers and mining companies for design work on new machines, as well as for evaluating proposed modifications to existing machines.

Jan 1, 1994

By R. L. Unger

Restricted fields of vision are a common problem with underground mining equipment. Also, when lighting systems are provided, they may be positioned where they cause glare. This restricts the visibility around the machines even further. To help address these problems, the US Bureau of Mines has developed a PC-based software package to aid in the analysis of certain human engineering aspects of mining equipment design. The software is available for use by equipment manufacturers and mining companies for design work on new machines, as well as for evaluating proposed modifications to existing machines.

Jan 1, 1995

By Ernest Y. Baafi

The usual tasks performed by a mine store include .removal, replenishment, ordering and deletion of items and updating of stocks. A personal computer Mine Store Inventory Database System MIDSYS for monitoring stocks in such a store is presented. The system consists of series of relational databases developed in dBASE III+ environment. The system has three main modules comprising of a store management module, a display module and an employee-store operation module. The third module is useful in tracing movement of store goods. The MIDSYS is menu .driven with help functions at all levels.

Jan 1, 1992

By R. L. Grayson

Following lip on a USBM-sponsored research project, the authors have utilized the knowledge-base structure and system concepts from the Sun Sparcstation-based worker scheduling system of the Mine Management Support System to develop a PC-based application. The new software adopts the nested-window concept to facilitate data collection and modification on personnel, their availability on a shift, and work priorities for a shift as well as to allocate manpower optimally on a work shift and delineate supervisory training responsibilities. The various components of the software are described in detail, along with enhancements made to the original system.

Jan 1, 1996

By John Hardy

The performance of five dense-medium washers was evaluated in four preparation plants. Three of the plants were making a two-product separation that produced a clean coal and a refuse; one plant employed dense-medium vessels in series to effect a primary and a secondary separation. The secondary drum-type washer produced a low-ash metallurgical coal and an intermediate-ash product suitable for plant fuel or steam generation. The sharpness-of-separation was excellent for all four primary separations and the secondary separation.

Jan 1, 1966

By Kenneth L. Rubow, Virgil A. Marple, Ye Tao

Techniques are being developed for measuring the mass concentration of respirable diesel exhaust particles found in underground coal mines. Studies have been conducted over the past five years to investigate size selective sampling techniques to measure the respirable mass concentrations of diesel exhaust and mine dust aerosol particles in underground coal mines. Results from these studies have been used to develop design and performance criteria for a personal diesel exhaust aerosol sampler. Three personal diesel exhaust aerosol samplers have subsequently been designed and evaluated in both laboratory and field settings. These samplers use size selective classifiers for the determination of the respirable mass concentrations of mineral dust and diesel exhaust particles. Their designs are based on the premise that diesel exhaust particles are predominantly less than 0.8µm while mineral dust is greater than 0.8 µm. One design, selected for field evaluation, consists of a 10 mm nylon respirable dust cyclone followed by a 0.8 µm cutpoint impactor and afterfilter. The cyclone removes the large nonrespirable particles while the inertial impactor stage, collects the mineral dust on an impaction plate and allows the diesel particles to penetrate to an afterfilter. The two sample fractions of the respirable particles (<0.8 µm and >0.8 µm) are gravimetrically analyzed to determine the concentrations of the diesel and mineral dust portions in the respirable coal mine aerosol.

Jan 1, 1991

By A. Mahtab, S. Xu, P. Grasso, B. J. Fu

The large population base, complex geology of the large land mass, and notable commercial activity have accelerated the development of underground construction market in China. The projected lengths of underground openings per year in the various sectors are: hydro-tunnels, 180 km; coal mine entries, 40 km; transport-tunnels, 300+ km. An example of the mega projects (being planned by the Government) is the water supply scheme for connecting Yangtze river to Yellow river involving 131 km of water tunnels with a diameter of 8-10m. Several large projects are highlighted in the paper with reference to the schemes for generating hydro-power, mining of coal and minerals, and constructing transportation networks. The related problems of construction and geomechanics are outlined.

Jan 1, 1995

By J. Sandford, S. Hennings

EXECUTIVE SUMMARY An approach borrowed from the petroleum industry was applied to the gas development evaluation for the Bulga underground coal mine in New South Wales, Australia. The results enabled the coal mine operator, Xstrata Coal, to systematically plan the extraction of gas in harmony with mine production planning of multiple coal seams. This has allowed for a more proactive approach in preparing the resources and infrastructure needed to capture the gas and accelerate coal mining while maintaining their high level of commitment to safety. Norwest has for decades used gas recovery simulation models to assist the petroleum industry and the coal bed methane (CBM) industry in understanding and forecasting fluid saturations and flow behavior. Norwest developed a similar process with Xstrata to migrate existing mine data at Bulga into reservoir simulation models to study various drainage alternatives. An interesting feature to the evaluation was also developing an understanding of test procedures and nomenclature from the mining industry to properly translate the data for input in simulators developed for the petroleum and CBM industries. The model was then calibrated to actual field data collected from drainage pilot tests that Norwest helped design and monitor at Bulga. The resulting calibrated predictions were then used to develop budgets, schedules, resource requirements, and alternatives for capturing the gas and delivering it to market ahead of mining. Increasing revenue, reducing emissions, improving schedules and cutting costs for the mining operations have all contributed to justifying this advanced approach at Bulga. It has also allowed Xstrata to expand their focus to the sizable gas reserves in seams not currently planned for mining. Several of these seams would be economic gas development targets once the gas recovery infrastructure is installed for the mine. The evaluation process was refined throughout this project and the resulting approach will benefit Xstrata with their broader strategic development of resources in the Hunter Valley and beyond to their worldwide operations.

Jan 1, 2007

By C. W. Schultz

The Alabama tar sands of the Hartselle Sandstone formation present a more difficult problem in primary extraction than do the Athabasca tar sands. In contrast to the Athabasca tar sands, the Alabama tar sands are "oil wetted" and the contained tar, or bitumen, is of much higher viscosity. A physical beneficiation scheme was developed in which clean sand from an external source was used as a scrubbing medium. High intensity scrubbing liberated the tars which are readily recovered by froth flotation. Locked cycle tests have shown that, after the use of an initial ration of clean sand, the system produced enough new clean sand to be self sustaining.

Jan 1, 1992

By R. J. Sweigard

Differential settlement on reclaimed land presents a particular problem when the land is to be used for row crops. The poorly drained depressions caused by differential settlement restrict crop yield resulting in additional costs to alleviate the problem. Potentially more serious is the threat of failing to meet target yields due to settlement: related reductions. Because the mechanism by which the problem occurs is not well understood, a physical model study was conducted to investigate the importance of several factors. Although the importance of such factors as the relative amounts of rock and unconsolidated overburden in the undisturbed condition and the size distribution of rock fragments were considered, the analysis concentrated on the causes of settlement in the reconstructed soil layer above the rock spoil.

Jan 1, 1989

By P-M. Dupond, S. Lowrie, C. Tauziéde, Z. Pokryszka, A. D. Jones

A physical model has been developed to simulate the flows and mixing of gases in the waste of a longwall retreat coalface. The model is used in conjunction with computational modelling, and the distributions of permeability and gas emission in the model waste follow those in computer simulations (Pokryszka et al 1996). The physical model represents at 1170th scale a 200 m long, 3 m high coalface with a waste extending up to 280 m to the face start line. The model is tilted to the same seam slopes as the real face, e.g. 22° ascensional ventilation along the face and 7" slope to the dip. The purpose is to investigate the flow of three components: ventilation seepage flow through the waste; methane; and nitrogen injected to quell spontaneous combustion. A heavier-than-air surrogate gas (SF,) is used in place of methane, and therefore the model is inverted so that gas layers form along the &apos;roof". The main forces driving the flows in the waste (pressure gradients due to ventilation and the density difference of gas layers) are kept in proportion by appropriate scaling of the permeability. Calibration and validation used data from a coalface at a mine in the Lorraine coalfield. The model is now in operational use.

Jan 1, 1997

By P. S. Hettinger

Land Application Discharge (LAD) is a useful method of disposing of waste water from mining operations and in certain climatic regimes, stormwater runoff. LAD systems function under the premise that metals, salts and nutrients in water are dispersed over a large area and are effectively assimilated into the soil profile. Depending on the soil structure, migration or mobilization of dissolved metals through the soil profile can be Substantially reduced. Land application of treated effluent from sewage lagoons or waste water plants was probably the first general use of land applied water. LAD has gained popularity with the mining industry as a means of disposing of waste water and process water. In addition, large volumes of snow meltwater and stormwater are often placed in storage in Montana during spring, and Land Application Discharge has shown to be an effective method for disposing of stormwater during the dry, summer season. LAD can also provide an alternative to recycling or treating waste water at on-site waste water treatment plant&. Application of stormwater or process water can result in little or no change to the background concentrations of metals in baseline water quality samples. One cautionary note about LAD: high salt concentrations and pH values are associated with process water from heap-leach facilities and are known to cause burning of local vegetation. Some pre-treatment of process water may be necessary to prevent such environmental problems.

Jan 1, 1994

By V. Rajaram

The Parachute Creek Member of the Green River Formation in the Piceance Basin, Colorado, contains vast reserves of oil shale, nahcolite, dawsonite, and other accessory minerals. The dry alkali process of sulfur dioxide removal using nahcolite (naturally occurring sodium bicarbonate) has great potential. A room and pillar mining scheme has been designed to extract a nahcolite zone occurring at a depth of 472 m, from the lease application area of the Yankee Gulch Joint Venture. Geotechnical parameters affecting mine design will be discussed. A preliminary development plan for mining at the rate of 1000 t/d will be described in detail.

Jan 1, 1977