Search Documents

By Nik Sokol, Mike Jaeger, Leo C. Weiman-Benitez

Silicon Valley Clean Water signed a progressive-design-build (PDB) contract with Barnard Bessac Joint Venture (BBJV) to design and construct the Gravity Pipeline tunnel in Redwood City, CA. Owner and Design-Builder teamed with designer Arup to provide a final product: 3.3 miles of 182 in. O.D. precast concrete segmentally lined tunnel with 10 ft. and 11 ft. I.D. Fiberglass Reinforced Polymer Mortar (FRPM) carrier pipe, complete with two FRPM Drop Structures. BBJV and Arup collaborated with SVCW to evaluate alternative design concepts, negotiate an agreeable price and reduce contingencies through a transparent estimating process, and deliver the project ahead of schedule.

Jun 13, 2023

By Richard C. Travis, Edward C. Dowling

A detailed kinetic study of the flotation installation at the Metcalf Concentrator revealed a rougher flotation circuit operating under less than optimal conditions. Based on these results, a project was initiated to approximately double the rougher flotation capacity by increasing the installed volume from 780 cubic meters to 1,560 cubic meters. This project, which was completed in early 1991, replaced the existing cells with larger capacity cells. A comprehensive analysis of results demonstrates significant metallurgical benefits. INTRODUCTION/BACKGROUND The Metcalf Concentrator is located in Morenci, Arizona and is part of Phelps Dodge Morenci, Incorporated. Sumitomo Metal Mining of Arizona is a minority partner in the operation with 15% interest. The Metcalf Concentrator is the newer and smaller concentrator and operates in conjunction with the Morenci Concentrator. Operating capacity at Metcalf is currently 48,000 TPD of ore on a 365 days per year basis. The Metcalf Concentrator was commissioned in 1974 at a 30,000 TPD operating rate for the purpose of treating ores originating in the Metcalf Mine. The mine takes its name from the former town of Metcalf which was named for Robert Metcalf who was credited with discovery of the mineral district. The predominant ore mineral is chalcocite which occurs as a secondary enrichment closely associated with iron pyrite. The host rock is largely granodiorite and quartz monzonite. The original rougher flotation circuit consisted of a total of six rows of Wemco 8.5 cu. meter (300 cu.ft.) flotation machines treating pulp from the two grinding sections (Sections A and B). Each row was configured in a 4-4-4 arrangement. Shortly after startup the throughput rate was increased significantly without sustaining a recovery loss. This increase was achieved by raising the target value for the particle size of the cyclone overflow which is the rougher flotation feed. Shortly thereafter, the capacity of the pump and cyclone began to restrict further increases in throughput. After testing, two 66 cm. (26-in.) cyclones and a 12-in. X 12-in. centrifugal pump replaced the original classification equipment. As a result of these modifications, the grinding section could routinely process in excess of 42,000 TPD. Due to the increased tonnage rates, limitations in the rougher flotation circuit performance were observed. In an effort to improve the performance of rougher flotation with this higher throughput, the speed of the flotation mechanisms was increased from 230 RPM to 250 RPM. This change improved the suspension of the coarser feed and induced additional air into the pulp. It did, however, apply additional strain to the motors, shortening their life. At these elevated processing rates, it was found that the dart valves operated almost entirely at the top end of the control range and could not efficiently handle upsets from the grinding section. This was remedied by lowering the end overflow weir and allowing some of the tailings to overflow the end weir. However, in order to obtain acceptable recovery levels, the flotation pulp was maintained at a high level, adversely influencing the rougher concentrate grade.

Jan 1, 1993

By Donald E. Warnken

The Study concerns the estimation of fair market value (FMV) of non-producing mineral rights. Two approaches to value are used and the values determined by each are compared. The Study area environment is unusual. The tectonics is visible on surface rocks throughout much of the study area. The effect on mineral values in the exposed areas has been compared to areas where the tectonics is not visible.

Jan 1, 2005

By A. B. Cecala

An evaluation was recently performed on a district recirculation system at a trona mine in Granger, Wyoming. A 1.52m (5 ft) diameter, 37.3kw (50 hp) vane axial fan was installed in a crosscut between the intake and return airways and recirculated approximately 31.4 m'/sec (66,578 ft'/min) of air back into the intake. This amounted to a recirculation factor of approximately 20 pct of the return air. This air was part of the primary ventilation to three different continuous miner sections at operating distances of between 6l0m (2,000 ft) and 1,829m (6,000 ft) from the recirculation fan. The mine environment was constantly monitored for respirable dust, methane, and carbon monoxide in the operating sections and in the main intake and return entries. In addition, air samples were taken with and without the recirculation system during the evaluation and analyzed using gas chromatography. The results of this study showed only small increases in dust, while all other mine contaminants remained at such low levels that it was impossible to determine any relative changes from the recirculation system. Because of this, a brief SF. tracer gas analysis study was subsequently performed to more precisely determine an increase in a mine contaminant with the recirculation system.

Jan 1, 1991

By H. Sato, B. Thornton, K. Nishi, A. Usui

"Northwestern Pacific submarine seamounts are believed to be future marine mining areas of ferromanganese crusts, which contain hi-tech industrial metals, such as Co, Ni, Te, Ti, Pt, and REEs. The Takuyo No. 5 seamount is a member of the Cretaceous super-plume seamounts in the north Pacific, located within a Japanese EEZ (100 nm from the Minami- Torishima Is. or Marcus Is.), and only 300 nm away from the Japan’s Licensed area for exploration of Co-rich ferromanganese crusts under the ISA. This is an on-going program supported by independent academic communities but not a state-run program or managed by private funding.We have observed, sampled, measured, and analyzed the occurrences, distribution, physical properties, and microbiological environments at a selected flat topped seamount named Takuyo No.5 as a model area for scientific study of ferromanganese crusts within the Japanese EEZ. We then characterized crust structures, composition, age, and growth history, resulting in an understanding of the overall nature and distribution of these deposits from wide range of areas, water depths and geological environments. The study started with a ROV (Hyper-Dolphin 3K of JAMSTEC) exploration jointly with universities and national institutions (Japan Agency for Marine-Earth Science and Technology, Japan Oil, Gas, and Metal Exploration Corporation, and Geological Survey of Japan) in 2009 using marine geology vessels, remotely-operated vehicle, an oceanbottom drill machine, deep-tow TV camera, as well as conventional dredges and corers. We have been studying the topography, geology, nature of the bottom material of the seamounts using delicate sampling devices and measurement tools, and characterized the distribution patterns of the metal-rich ferromanganese deposits from chemical, mineralogical, and microbiological points of view."

Sep 1, 2014

By Yoginder P. Chugh, K. V. K. Prasad, R. Missavage

This paper presents results of field monitoring and finite element studies to analyze and improve a room-and-pillar retreat mining system. Fie1 d instrumentation was utilized to monitor pi11ar load changes, roof to floor convergence and differential roof strata movement as retreat mining progressed and to determine in-situ horizontal stresses. A two-dimensional finite element model depicting strata behavior at this mine was developed and used to analyze existing and alternate improved mining geometries. The results showed excellent correlation between fie1 d observed and model predicted behavior. Some of the recommended changes in mining geometry based on the study were incorporated in the mining system.

Jan 1, 1986

The Bureau of Mines, U.S. Department of Interior, is currently investigating strata interactions associated with the mining of multiple coalbeds. Strata interactions due to subsidence are a result of undermining. This study involves underground investigations at a mine where room and pillar panels are actively being developed through an area of the Sewickley Coalbed which was subsided by undermining of the Pittsburgh Coalbed. Research to date indicates that undermining had little effect on upper mine pillar stability, but had a more severe effect on the development and maintenance of entries. Roof-to-floor measurements recorded over four times more convergence in entries developed over gob as compared with entries developed over support pillars in the lower mine. Consequently, this has led to major roof falls in the active panels, resulting in considerable production delays and supplemental roof support costs.

Jan 1, 1985

By J. F. T. Agapito, J. B. Page

This paper describes part of a geotechnical study based on stress determinations and convergence measurements conducted to assess the long-term stability of an experimental room-and-pillar oil shale mine. A rock mechanics program was initiated in 1971 at the Colony Mine as part of a large study conducted for the design of a commercial operation. The Colony Development Operation is a joint venture currently consisting of four active members; Ashland Oil Inc., Atlantic Richfield Company (Operator of the project), Shell Oil Company, and The Oil Shale Corporation. Although oil shale commercialization plans are presently suspended, rock mechanics instrumentation has been continued as part of Colony's policy in maintaining readiness to proceed with a commercial shale oil plant when national energy policies became better defined. The property is located in the southern edge of the Piceance Creek Basin in northwestern Colorado, approximately 200 miles west of Denver. Experimental mining operations were conducted from 1965 to 1972 with one of the major objectives of the pilot mine being the assessment of opening and pillar sizes for the determination of extraction ratio and life of the property. Mining was conducted in a 60 foot thick portion of the Mahogany Zone in the Parachute Creek Member of the Green River Formation, at depths of 600 to 850 feet by a one-bench system. Pillar dimensions were 58 feet by 58 feet and rooms were 55 feet wide.

Jan 1, 1977

By Frank E. McCall, Michael A. Trevits, Fred Garcia

The U.S. Bureau of Mines investigated the influence of atmospheric pressure changes on methane gas migration through mine seals at a mine site located in the Pittsburgh Coalbed. The mine gained access to a coal reserve through part of an abandoned mine and constructed nine seals to isolate the extensive old workings from the active mine area. Underground problems were experienced when atmospheric pressure fell, causing methane gas to migrate around the seals and into the active workings. During mining operations, methane gas levels exceeded legal limits and coal production was halted until the ventilation system could be improved. When mining resumed with increased air flow, methane gas concentrations occasionally exceeded the legal limits and production had to be halted until the methane level fell within the mandated limit. To assist the ventilation system, a pressure relief borehole located in the abandoned workings near the mine seals was proposed. Preliminary estimates by a gob gas simulator (computer model) suggested that a 0.76 m (2.5 ft) diameter pressure relief borehole with an exhaust fan would be necessary to remove enough methane from the abandoned area so that the ventilation system could dilute the gas in the active workings. However, by monitoring methane gas emissions and seal pressure, during periods of low atmospheric pressure, the amount of methane gas that migrated into the active mine workings was calculated. Researchers then determined that a relief borehole, 20.3 cm (8-in) with an exhaust fan could remove at least twice the maximum measured volume of migrating methane gas. Because gas concentrations in the abandoned workings could potentially reach explosive limits, it was proposed that the mine eliminate the exhaust fan. Installation of the recommended borehole and enlarging two other ventilation boreholes located in the abandoned area reduced methane gas leakage through the seals by at least 63%.

Jan 1, 1995

By B. A. Kennedy

The instrumentation, monitoring, and prediction of a major slope failure at the Chuquicamata mine are described. In December 1967, pre-existing tension cracks on the south end of the east wall of the Chquicamata mine began to open. Various forms of instrumentation were installed for continuous monitoring. These systems included tension crack stakes, crack extensometers, linear extensometers, tape and transit lines, sliding wire contacts, and a seismograph. From the information obtained, the failure date was accurately predicted some five weeks before failure, enabling the mine to reroute truck and rail access; hence, causing a minimal mine shutdown of two and one-half days and preventing any injuries to persons or damage to equipment. The shape and form of the sliding mass are analyzed, as are the possible modes of failure.

Jan 1, 1970

By D. J. Rose

The San Miguel Mine is owned by San Miguel Electrical Cooperative, Inc. and operated by Atascosa Mining Company, a wholly-owned subsidiary of Morrison-Knudsen Company, Inc. This multiseam, single-zone lignite surface mine is located near Jourdanton, Texas, 110 kilometers (68 miles) south of San Antonio. Lignite extracted from four closely-spaced seams is used to fuel the 400-MW San Miguel Power Plant. Recovery depths range from 7 to 37 meters (25 to 120 feet). The mine began stripping operations in the spring of 1980 and now produces approximately 2.5 million tonnes (2.8 million tons) of lignite annually. Atascosa Mining Company is responsible for production, maintenance, engineering, and management services. Production responsibilities include topsoil removal, overburden removal, lignite mining, spoil pile regrading and topsoil replacement, as well as ash disposal and construction and maintenance of water retention and diversion facilities.

Jan 1, 1984

By Ihsan Berk Tulu, Mark Van Dyke, Ted Klemetti, Deniz Tuncay

"Longwall abutment loads are influenced by several factors, including depth of cover, pillar sizes, panel dimensions, geological setting, mining height, proximity to gob, intersection type, and size of the gob. How does proximity to the gob affect pillar loading and entry condition? Does the gob influence depend on whether the abutment load is a forward, side, or rear loading? Do non-typical bleeder entry systems follow the traditional front and side abutment loading and extent concepts? If not, will an improved understanding of the combined abutment extent warrant a change in pillar design or standing support in bleeder entries?This paper details observations made in the non-typical bleeder entries of a moderate depth longwall panel; specifically, it explores data collected from borehole pressure cells and roof extensometers, observations of the conditions of the entries, and numerical modeling of the bleeder entries during longwall extraction. The primary focus was the extent and magnitude of the abutment loading experienced due to the extraction of the longwall panels. Due to the layout of the longwall panels and bleeder entries, the borehole pressure cells (BPCs) and roof extensometers did not show much change due to the advancing of the first longwall. However, they did show a noticeable increase due to the second longwall advancement, a maximum of about 4 MPa of pressure increase and 5 mm of roof deformation. The observations of the conditions showed little to no change from before the first longwall panel extraction began to when the second longwall panel had been advanced more than 915 meters. Localized pillar spalling was observed on the corners of the pillars closest to the longwall gob as was an increase in water in the entries. In addition to the observations and instrumentation, numerical modeling was performed to validate modeling procedures against the monitoring results and evaluate the bleeder design. ITASCA Consulting Group’s FLAC3D numerical modeling software was used to evaluate the bleeder entries. The results of the models indicated only a minor increase in load during the extraction of the longwall panels. These models showed a much greater increase in stress due to the development of the gateroad and bleeder entries—about 80% development and 20% longwall extraction. The FLAC3D model showed very good correlation between modeled and expected gateroad loading during panel extraction. The front and side abutment extent modeled was very similar to observations from this and previous panels."

Jan 1, 2019

By J. S. Walker

Public Law 95-87 enacted by Congress in 1977 and subsequent regulations require coal mine operators to predict the effects of mining on the environment prior to the start of mining. Prediction of the effects of mining on the local groundwater system is a difficult task due to its complex nature and the lack of detailed published information. An investigation of water level fluctuations in five we1 1s positioned over three consecutively mined longwall panels was initiated in conjunction with an intensive subsidence monitoring program. The purpose of this work was to provide detailed information which could be used to predict certain hydrologic effects of longwall mining in the Northern Appalachian Coal Region. The results of this case study indicate that water level fluct- uations in the local ground-water system above longwall panels is associated with subsidence and that the static water level will generally re- establish at or near the pre-mining elevation after mining is completed.

Jan 1, 1986

By Reece Kurre, Gabriel Walton

"Roof bolting has long been used in underground mines across the world to provide ground support. Modern roof bolts are cheap and easy to install with the use of specialized machines as a part of the production cycle. Lhoist North America’s Crab Orchard Mine is an underground room and pillar limestone mine that uses mechanically anchored roof bolts for ground support. The mine currently employs two different roof bolting patterns: a standard 5 × 5 foot pattern, and a 2.5 × 2.5 foot pattern for use in areas with particularly hazardous roof conditions. The purpose of this study is to evaluate the relative effectiveness of each bolting pattern.A series of numerical models were created using RocScience’s RS2. The models were based on a symmetrical section of the mine at its deepest point, and were modeled using Generalized Hoek-Brown failure criterion along with a discrete fracture network. A series of sensitivity analyses were performed on the models by varying parameters such as joint friction angle, crack persistence, joint randomization, and tensile strength of the limestone. Based on the results of the original models and sensitivity analyses, it appears that the standard bolting pattern provides sufficient roof support capacity under almost all the expected conditions at the mine, since factors of safety below the design value of 1.5 were only found for individual bolts in a few of the worst test cases considered. These results can help improve the Mine’s productivity and reduce operating costs without compromising safety.INTRODUCTION AND CASE STUDY DESCRIPTIONLhoist North America’s Crab Orchard Mine is an underground limestone mine located in Crab Orchard, Tennessee. The mine is located under an 800-foot-high mountain, and outcrops on three sides. The mine is accessed through three separate portals and has two main levels, along with a partially developed third level. Extraction is accomplished by the room and pillar method using 50 × 50 feet pillars and 50 × 50 feet rooms. The mining height is limited to 50 feet to keep the pillar width to height ratio around 1.0. Each heading is excavated in a two-stage process that consists of a 30-foot-tall top heading and a 20-foot-tall bench. A distance of at least 30 feet is maintained between the two levels at all times (Crab Orchard Mine Technical Staff, 2017)."

Jan 1, 2019

By Yongsik Jeong, Kwangmin Kim

Most tailings storage facility (TSF) failures occur in active, upstream-type TSFs, often due to extreme and unexpected weather conditions—specifically, heavy rainfall and strong winds. This case study of a TSF in southern Arizona examines the use of the optimum safe beach distance (Doptimal, the optimum distance between the crest and decant pond) as a tool for monitoring geotechnical stability and reducing catastrophic failures. A digital model of the TSF was used to determine the critical beach distance (Dcritical) under normal weather conditions, and Doptimal was then determined by adding incremental distances to account for the effects of heavy rainfall (Drainfall) and strong winds (Dwind). To overcome accessibility issues, a drone was used to map the TSF geometry and create a digital model. This model served as the basis for conducting a coupled stress-seepage, finite-element (FEM) analysis with a safety factor of 2.0 to assess geotechnical stability (Dcritical). The safe beach distance increments were determined using the PMP (probable maximum precipitation) and possible maximum wind speed. Based on this analysis, the optimal safe beach distance at the study site was identified as 202.2 m. Since the current beach distance (371 m) exceeds this value, the TSF was considered to be stable and satisfied the design safety factor of 2.0. However, this distance should be reassessed periodically to account for changes in the TSF geometry and other conditions. Furthermore, it applies only TSFs that are well-managed and feature a smooth, non-undulating beach surface with a consistent slope.

By Yongsik Jeong, Kwangmin Kim

Most tailings storage facility (TSF) failures occur in active, upstream-type TSFs, often due to extreme and unexpected weather conditions—specifically, heavy rainfall and strong winds. This case study of a TSF in southern Arizona examines the use of the optimum safe beach distance (Doptimal, the optimum distance between the crest and decant pond) as a tool for monitoring geotechnical stability and reducing catastrophic failures. A digital model of the TSF was used to determine the critical beach distance (Dcritical) under normal weather conditions, and Doptimal was then determined by adding incremental distances to account for the effects of heavy rainfall (Drainfall) and strong winds (Dwind). To overcome accessibility issues, a drone was used to map the TSF geometry and create a digital model. This model served as the basis for conducting a coupled stress-seepage, finite-element (FEM) analysis with a safety factor of 2.0 to assess geotechnical stability (Dcritical). The safe beach distance increments were determined using the PMP (probable maximum precipitation) and possible maximum wind speed. Based on this analysis, the optimal safe beach distance at the study site was identified as 202.2 m. Since the current beach distance (371 m) exceeds this value, the TSF was considered to be stable and satisfied the design safety factor of 2.0. However, this distance should be reassessed periodically to account for changes in the TSF geometry and other conditions. Furthermore, it applies only TSFs that are well-managed and feature a smooth, non-undulating beach surface with a consistent slope.

By Justine Ealy, Daniel Yang, Christina Foster

Maintaining stable high walls can be a challenging task. Complex geological and structural features, alteration zones, rock mass properties, and hydrogeological conditions must be well understood to design a safe mining environment. Economic considerations must also be taken into account as the mine operator must provide ore deliveries and protect reserves. However, even when good engineering practices are followed, and proper blasting and mining techniques are implemented, slope movements may still occur. When these slope instabilities are minor, the mine is often able to continue operations with minimal impacts on safety or production. When these occurrences are excessive and coupled with high rates of movement, a robust monitoring system is crucial to continuing mining activities while protecting personnel. This paper summarizes the approach an open pit mine in Nevada took as excessive and rapid high-wall movement was experienced in an integral area. Creative mining approaches, combined with slope monitoring radar technology, were utilized to maintain safe and successful mining activities despite active movement that exceeded an average velocity of 30 inches per day.

Feb 1, 2024

By M. Sears, K. Mohamed, J. Addis, J. Wickline, G. Rashed

To better understand the load shedding and the stress transfer on coal pillars due to room-and- pillar retreat mining in deep cover panels, researchers from the National Institute for Occupational Safety and Health (NIOSH) conducted a monitoring field study. Two sites, at overburden depths of 1,000 ft (304.8 m) and 1,500 ft (457.3 m), were selected in a room-and-pillar mine operating in Southern West Virginia. The deformation and stress changes in the roof and two adjacent pillars at each site were monitored during the retreat mining process. The monitoring results and field observations were used to calibrate large-scale FLAC3D models for each site. The calibrated models were used to assess different sizes of roof bolts installed in deep cover areas. INTRODUCTION Deep cover room-and-pillar retreat mining is an important emerging issue that will intensify in the future as shallower reserves are depleted (Mark, 2009; Chase et al., 2002). During pillar retreat mining, the likelihood of local and/or global instabilities increases due to elevated stress levels near the pillar line because of the abutment loading. In the last decade, approximately 31% of the room-and-pillar mining groundfall fatalities in the United States occurred during pillar retreat mining. Between 2013 and 2017, this proportion increased to 55%, of which 50% of these fatalities were due to falls of roof and rib that occurred during pillar recovery (MSHA, 2018). One interesting piece of information about pillar recovery fatalities was that the victim was nearly always under bolted roof. Sheared and broken #5 (5/8-in), fully grouted rebar bolt failure contributed to three of four fatal roof fall incidents that have occurred in deep cover retreat mines (NIOSH, 2010). This claim raised the following question at the study mine: Is it safe to use a 4-ft long #5 (5/8-in) rebar bolt grade 60 at a depth of cover more than 1,000 ft (304.8 m)? There was some concern about shear failure of the #5 (5/8-in) rebar bolt at a depth of cover over 1,000 ft (304.8 m). To answer the question and to reduce accidents and fatalities caused by ground falls due to room-and-pillar retreat mining in deep cover panels, the National Institute for Occupational Safety and Health (NIOSH) monitored the roof and rib deformation and the change in vertical pressure within two adjacent pillars during pillar recovery. The study was conducted at two deep cover sites in a room-and-pillar mine located in Southern West Virginia that operates in the Lower War Eagle (LWE) seam. The monitored sites were selected at 1,000 ft (304.8 m) and 1,500 ft (457.3 m) depths of cover. In this paper, site-1 represents the monitored site at 1,000 ft (304.8 m) of cover, while site-2 represents the monitored site at 1,500 ft (457.3 m) of cover. For this study, large-scale FLAC3D numerical models were calibrated based on both field observations and instrumentation results. The calibrated models were then used to compare the ground response and the induced stresses of two pillars at instrumented sites 1 and 2. The maximum lateral displacement (roof shift) obtained from the calibrated large-scale FLAC3D models was applied to a small-scale FLAC3D bolted models, the safety factor for axial stresses of the simulated roof bolts was calculated at the deep cover sites.

Jan 1, 2019

By Michael J. Martinson

A powerful methane explosion in the mid-shaft pump station of a main service and ventilation shaft killed several persons on the station; more workers were killed when a mancage travelling down the shaft fell to the shaft bottom under a pile of broken concrete slabs from a brattice wall destroyed by the explosion venting into the shaft and a tangled mass of twisted steelwork from the equipped compartment. The newly-commissioned shaft serves a recent extension of an established mine on the Orange Free State (OFS) goldfield in South Africa. After outlining the circumstances in which the paper was written, and reviewing the nature and extent of the methane hazard in OFS mines, the paper describes the physical layout of the shaft and summarises evidence given by witnesses at the official inquiry concerning events prior to the explosion. No attempt is made to apportion blame for the incident.

Jan 1, 1989

By Aaron Jones, Guy Reed, Russell Frith

"In 2017, one of the international authorities on coal bursts, Dr. Chris Mark, published a paper entitled “Coal Bursts that Occur during Development: A Rock Mechanics Enigma,” in which several relevant technical issues were identified, the most pertinent being:i.whilst development coal bursts are commonly associated with geological faults, understanding which specific faults result in burst-prone development mining conditions and why, remains undefined.ii.conventional wisdom in relation to strong roof and floor geology of the coal seam might be limiting, based on certain burst examples in Colorado.iii. development coal bursts can occur without the local ground stresses being substantially elevated from their in situ levels.This paper outlines what is considered to be a credible, first-principles, mechanistic explanation for these three current development coal burst conundrums by reference to early published coal testing work examining the significance of a lack of “constraint” to coal stability and an understanding of how very specific structural geology and other geological features can logically cause this to occur in situ, albeit on a statistically very rare basis. This basic model is examined by reference to published information pertaining to the development coal-burst that occurred at the Austar Coal Mine in New South Wales, Australia, in 2014 and from the Sunnyside District in Utah, USA.The “cause and effect” model for development coal bursts presented also offers a meaningful explanation for the statistical improbability for what are nonetheless potentially highly-destructive events, being able to explain the statistical rarity being just as important to the credibility of the model as explaining the local conditions associated with burst events.The model could also form the basis for a robust, risk-based approach utilising a “hierarchy of controls” to the operational management of the development coal burst threat. Specifically, these include the use of pre-mining predictions for likely burst-prone and non-burst-prone areas, the use of the mine layout to avoid or at least minimise mining within burst-prone areas if appropriate, and finally the development of an operational Trigger Action Response Plan that reduces the likelihood of inadvertent roadway development into a burst-prone area without suitable safety controls already being in place."

Jan 1, 2019