Search Documents

By J. M. Mutmansky

Introduction Since the Hardy Cross numerical algorithm was applied to the solution of mine ventilation networks, numerous developments have taken place in ventilation network analysis procedures. The Newton-Raphson method, the linear theory method and the second-order approximation method are three of the additional approaches that have been applied. The efficiency of a ventilation network analysis procedure depends not only on the method of solving the system of equations derived from ventilation networks but also on the method of deriving the equations through selection of the meshes. This paper investigates the impacts of three mesh selection methods on the efficiencies of four ventilation network procedures. The minimum-resistance spanning tree method is the most popular procedure for selecting meshes. The shortest-path method was suggested by Epp and Fowler (1970) for improvement of the Newton-Raphson method. The minimum-resistance-path method is suggested here as the third method of selecting meshes. The effects of these three methods on the Hardy Cross method, the Newton-Raphson method, the linear theory method and the second-order approximation method are analyzed in this paper. These network analysis methods have been summarized in the paper by Kim and Mutmansky (1991). Mesh selection methods A procedure for mine ventilation network solution based on mesh equations typically consists of two steps: • the mesh selection step and • the network solution step. The mesh selection step establishes a set of independent equations to solve the network. The resulting equations are nonlinear. One method of solving nonlinear equations is to linearize the equations and iteratively solve these linear equations. The four analysis methods previously discussed in this paper use this approach. The linear equations required for solution can be written in matrix form as: P•dQ = dF (1) where P is the pseudo-resistance matrix, Q is the quantity matrix, and F is the Jacobian matrix (Kim and Mutmansky, 1991). The efficiency of the solution method depends on the characteristics of the P matrix, which in turn depend on the method of selecting meshes. To understand the impacts of the mesh selection methods on the efficiency of the ventilation network analysis procedures, the characteristics of the P matrix must be understood first. The diagonal elements of the P matrix, m in number, are the sums of the pseudo-resistances of the branches contained in the m meshes necessary for solution. The off-diagonal elements are the sums of the pseudo-resistances of the branches shared by two meshes. For example, P12 (first row, second column element of the P matrix) is the sum of the pseudo-resistances of the branches common to mesh 1 and mesh 2. When solving the system of equations expressed in Eq. (1), three of the iterative procedures (the Newton-Raphson, the linear theory and the second-order approximation methods) use the direct factorization method (Burden and Faires, 1985) on the P matrix. When the direct factorization method is used, the computational efficiency is enhanced by larger diagonal elements and a sparser P matrix. Generally, the sparsity of the P matrix is more important than the size of the diagonal elements. There is no known mathematical method of predicting the efficiency of these procedures, but heuristic methods can be used to study the efficiency. The Hardy Cross algorithm applies the Gauss-Seidel method of splitting the P matrix and applies the Newton-Raphson procedure. The efficiency of the Hardy Cross method depends on the spectral radius of the matrix[[D-L]-1U], where D is the diagonal, L is the lower triangle and U is the upper triangle of the P matrix for the Newton-Raphson method (Ortega, 1972). The smaller the value of the spectral radius, the faster the convergence. As with the other three methods, larger diagonal elements and a sparser matrix aid in faster convergence. With the Hardy Cross method, however, the size of the diagonal elements is more important than the sparsity of the matrix. Remembering that each of the diagonal elements of the P matrix is the sum of the pseudo-resistances of the branches in a mesh and that each off-diagonal element is the sum of the pseudo-resistances of the branches shared by two different meshes, the following strategies can be used: • Avoid having branches with larger resistance values shared by multiple meshes. This increases the size of the diagonal elements and reduces the chance of off-diagonal elements being large.

Jan 1, 1993

By Joseph B. Alberts, David D. DiPonio, Francis B. Manning

From 1996 to 2001, Wayne County and 13 suburban Detroit communities constructed the Downriver Regional Storage and Transport System (DRSTS) to improve area water quality, protect public health and alleviate basement flooding. The project consisted of a 10-mile long storage and transport tunnel, a pump station at the existing wastewater treatment plant, 9 miles of relief sewers (6 in tunnel and 3 in open cut). The work was separated into 10 contracts. Due to hydraulic design requirements and other constraints, the tunnel profile was located generally 65 feet below ground surface within a soft to medium clay strata which skimmed along the top of a very dense glacial till “hardpan” overlaying bedrock. Boulders within the tunnel bore were recognized as a significant, but indeterminate risk. This paper presents a case history of the owner’s contracting strategy for risk assumption and management of the boulder impacts on the project. Actual conditions encountered during construction and contractual adjustments made to address problems are reviewed, and recommendations for future contracts are included.

Jan 1, 2003

By Ted H. Eyde

Improving the mineral industry's tarnished image describes in a nut- shell the reason why the Speakers Bureau of the Tucson Subsection of the AIME was formed. Let's go back in time about 3 years to the fall of 1971. Literally thousands of bills detrimental to the mineral industry were being introduced into Congress and State Legislatures. Unfortunately, many were being passed and signed into law. Clean air and water, zero pollution, preserve the environment, ecology, biodegradeable, wilderness were the words that the self- styled ecologists and environmentalists were preaching. The mineral industry either sat mute or in place of acting, reacted in a way certain to attract a maximum amount of bad publicity with a minimum amount of rhetoric. A mining company president, for example, commenting on the primary air standards in Arizona was reported by the press as having said, "we'll shut all the smelters down and put thousands of Arizonans out of work if we have to meet the Arizona standards." Or another defending a poorly planned highly visible open pit nonmetallics operation, "we'll take the whole mountain down if we want to, and nobody can stop us" and still another manager of Operations, "the bottom line is all that counts, to hell with all of this environmental nonsense."

Jan 1, 1975

By Dennis D. Fischer

The second underground coal gasification experiment conducted by ERDA's Laramie Energy Research Center at a site near Hanna, Wyoming, was completed on July 30, 1976. During the experiment production reached 0.32 Mm 3/d (12 Mft3/d) of 6.9 MJ/m3 gas (175 Btu/ft 3 ). Approximately 6100 tonne (6700 ton) of coal were gasified during the experiment. Energy return ratios of 4.5 to 5.3, cold gas - thermal efficiencies of 76 to 89 percent, and overall process efficiencies of 65 to 74 percent were achieved during the second Hanna experiment. This paper describes the experiment and the results obtained with emphasis given to the determination of the energy recovered relative to energy consumed in conducting the test. Data from this determination are compared with previously published data from the first test conducted at Hanna during 1973-1974.

Jan 1, 1977

By Caibin Wu, Chengfang Yuan, Jiaqi Tong, Zhilong Cheng, Ningning Liao, Chong Zeng

In a series of Julius Kruttschnitt size-dependent breakage models, the cumulative percentage passing 1/10 of the initial size is used as a fineness indicator for scientific research and the selection of grinding equipment. However, in industrial practice, it is quite customary to use the mass percentage passing 75 μm as the indicator. In this paper, based on the energy-particle size model, quartz and calcite, two materials with distinctly different hardness, were used as test samples in a conical ball mill. At the same specific energy, the value of the cumulative percentage passing 1/10 of the initial size decreased while that of the mass percentage passing 75 μm increased with finer feed size. The experimental test values of the mass percentage passing 75 μm have a good linear relationship with the model predictions, which suggests that the particle size energy relationship of the mass percentage passing 75 μm and Ecs can be used instead of the cumulative percentage passing 1/10 of the initial size and Ecs. By building family curves, when particle size x < 300 μm, the family curve can be well fitted, and the fine particle size distribution of the whole product can be reconstructed.

Dec 22, 2022

By Eugene L. Foster

The engineering profession has traditionally devoted its efforts to understanding and modifying the Earth&apos;s environment in order to adapt it to man&apos;s needs. In appraising our overall performance, I would have to say it has been a mixed bag. In many areas, notably communications taken in the broadest sense, and development of creature comforts, we have done a good job. In others, we have failed, particularly in our assessment of the effect of our work on the environment. Our failures have been due in part to a lack of understanding or foresight, and in part to a disproportionate emphasis on lowest first cost. Now, with an increasingly large number of people living in a finite environment, there is an urgent need for reassessment. It is no longer possible to pursue a single objective without regard to its side effects. Our projects are too large, and there are too many of them. Environmental impacts must be taken into account in all important engineering decisions of the future. There are forces at work which will help to bring this about. Thinking people everywhere have realized that adverse alteration of our environment eventually affects every one of us. The majority of our citizens, who now live in cities, are beginning to appreciate the advantages of a good natural environment in a way which others who have been closer to the soil have appreciated for years. Our people have flocked to the cities because they wanted to be "where the action is." At the same time, there is a strong desire for what we have come to call the quality of life. Today, we all want the standard creature comforts. We want to be able to move freely

Jan 1, 1974

By David R. Klug, Chris Gause, Troy L. Page

The Inter-Island Tunnel is one of two undersea tunnels which are part of the Boston Harbor Clean-Up Program. The tunnel is 7.7 km (25,160 ft) long, bored to a 4.3 m (14 ft) diameter in the Cambridge Argillite Formation and was finished to a 3.5 m (11.5 ft) diameter final concrete lining. The owner is the Massachusetts Water Resources Authority (MWRA) who is a regional authority responsible for overall design and construction. The tunnel&apos;s primary purpose is the transport of untreated effluent from Nut Island facility in Quincy, MA to the new treatment plant at Deer Island. Two sludge lines are installed for the transport of sludge from Deer Island to Nut Island. During construction the contractor encountered fault zones, fractured strata, and soft ground tunnel sections which liberated more ground water than was originally anticipated by the project designer. Ground water was controlled during mining and the placing of the final lining. The final lining of cast-in-place concrete had to be backfill grouted to cut off water inflows and provide contact for equal tunnel loading which is critical in long-term design. This paper deals with an engineered backfill grouting system which was the first of its type to be used in North America. It discusses the geological conditions encountered, the design criteria used in the evaluation process, and an indepth review of the various system components. It demonstrates how contractors can use knowledgeable and professional industry suppliers to solve difficult construction problems.

Jan 1, 1999

By Lawrence Adler

The design of an underground opening involves the coincidence of two highly complex and poorly specified components. First, the structural or mechanical characteristics of a geologic rock mass are not only extremely variable but are also very difficult to evaluate. Second, the general lay¬out of mine workings contains a large degree of indeterminancy as to the structure itself as a result of the indefiniteness of the mining process, and also because of the inherent redundancies associated with bulky and weighty structures. Even for the relatively simple problem of tunneling this complexity is well recognized to be "without question that to which the study of geo¬logy (for the Engineer) can most fitly and usefully be applied".1 It can, therefore, be appreciated that the comprehensive opening design problem involves a complicated assemblage of component structures made up of a sketchily defined, or sometimes even an undefined material and acted upon by largely unknown tectonic forces.

Jan 1, 1968

By C. John Dunnicliff, Birger Schmidt

INTRODUCTION To be effective and useful, monitoring of tunnel construction must be carefully planned throughout all steps. A vital and frequently overlooked step is a clear definition of the specific purposes of the instrumentation. Most tunnel construction monitoring has in the past been of benefit to research, the advancement of tunneling practice, wittingly or not. The development of monitoring instrumentation for the benefit of the project from which the data are recovered has very significant potential for risk and cost reduction of soft ground tunneling. A systematic approach to tunnel construction monitoring, from conception to full implementation, includes at least the following nine tasks or steps: Definition of benefits and purposes; design and project specification to draw full benefits; selection of monitoring parameters; selection of instruments and writing of specifications for procurement and installation; procurement and installation; reading and maintenance; data storage and retrieval; interpretation; implementation. Some of these steps are fairly easy and resolved through the use of established theories and technologies. The difficult ones are those that require the bending of minds, those that involve changes in the ways engineers design soft ground tunnels, the way owners pay for tunnels, and the construction is managed, inspected and controlled. Performance monitoring can be of benefit to the owner, design

Jan 1, 1974

By Qing-Wang Hao

In this paper, the authors attempt to develop engineering based approaches for estimating safety factors against pillar and floor failures and predicting likelihood of subsidence events over abandoned coal mines in Illinois. There are two critical problems involved in the analysis: determination of geotechnical properties, and consideration of time effect. The authors attempt to solve the problems by generating hypotheses, which are used to modify existing engineering models for estimating pillar and floor safety factors. The modified models are validated using data from two well established databases of subsidence events over active and abandoned mines in Illinois. The data analysis suggests that most of the trough type subsidence events in Illinois were caused by floor failures rather than pillar failures. The subsidence incubation period seems to be directly related to initial floor safety factors at the time of mining. This correlation can be used to predict the likelihood of subsidence and to assess subsidence risks within both spatial and temporal contexts where detailed mine maps are available.

Jan 1, 1986

By A. W. Khair

This paper presents an engineering approach to solve a complex ground control problem at reduced cost, allowing the mine to be operated safely and economically. The mine has experienced serious and complicated cutter roof problem in the entries. This cutler roof problem has delayed the advance of the entry development considerably and cost of these entries is very high due to the requirement of very heavy artificial supports. The analysis includes assessment of the cause of cutter roof and step by step action taken to improve the entry condition through appropriate longwall panel entry design and roof support system. The approach for solving the problem was two-fold: 1) to apply yield pillar concept in order to reduce the effects of in-situ horizontal stress in the roof strata and 2) to find an effective way to reinforce the roof strata and to support the fractured roof and avoid caving.

Jan 1, 1990

By Michael J. Virnig, Murdoch W. MacKenzie, Michael R. Davis

The objective of this paper is to present preliminary capital and operating cost estimates (±25%) comparing conventional carbon-in-solution (CIS) with resin-in­solution (RIS) using AuRIX® 100 for the recovery of gold and silver from typical heap leach solutions. Preliminary testwork was carried out with AuRIX® 100 using real and synthetic leach solutions to determine the technical viability of the resin for gold/silver recovery and to provide process design parameters for the preliminary RIS circuit. The scope of the resin testwork was sufficient to support the level of accuracy applied in the capital and operating cost estimates. No parallel testwork was carried out with activated carbon. Industry standard design data and operating data from existing CIS operations were used as a basis for the comparison. Both the capital and operating cost comparisons indicate a substantial savings for a RIS circuit using AuRIX® 100 (- 14 to 18% in terms of capital and 25 to 35% in terms of operating costs) over a conventional CIS circuit depending upon solution flows and grade.

Jan 1, 1999

By Alex G. Sciulli

According to recent estimates, nearly 30 percent of the material from underground coal mining in the United States is rejected on the surface as waste. This accumulation of almost three billion tons of coarse and fine coal refuse is primarily from coal cleaning operations. The marketable coal is intermixed with sandstone, clays, shales, and carbonaceous rocks, which must be removed and disposed of in an acceptable manner. The disposal of mineral wastes is a major environmental concern. The most common types of environmental problems associated with coal refuse disposal are acid formation, erosion, and sediment control. Other areas of concern include air and water quality, combustion control, mine sealing, and reclamation. This paper focuses on these topics and attempts to outline special environmental features which can be incorporated into the design and construction of a coal refuse facility. Often these measures can minimize and possibly eliminate the potential environ- mental hazards. It is imperative, however, that these measures be adopted prior to and during construction, because of the relative ease and cost savings compared to post-construction implementation.

Jan 1, 1983

By Peter Keppler, Charles Jackson

WHY DO AN AUDIT? There is increased enforcement of environmental laws and regulations at State and Federal levels with attendant steep fines and even the possibility of jail sentences. We are all aware of environmental and public health and safety incidences (i.e., Love Canal, Bhopal) which have led to stringent laws and regulations (i.e., CERCLA, RCRA, SARA). In some cases, the courts have specified that a company institute an audit program as a condition of settlement of claims which related to lack of environmental control. The U.S.EPA issued an Environmental Auditing Policy Statement in the November 8, 1985 Federal Register (pp. 46504-46508) which encourages the use of environmental auditing by regulated entities. Elements of what EPA considers to be an effective environmental auditing program are outlined and briefly explained. These factors combine to indicate why there is a growing number of companies which have instituted an audit program. Briefly, the program can and should be used to monitor compliance with environmental regulations and corporate policy, to prevent violations, to improve policies and procedures, to raise the level of environmental awareness, to encourage communication among operations and all management levels about environmental problems, and to measure risks and control costs. AMAX Inc. has had an environmental audit program since the early 1970&apos;s. The AMAX Environmental Affairs Department, working with the Law Department, oversees and coordinates environmental audits and analyzes the findings which an audit reveals. Facilities are audited on a regular schedule; those having the greatest potential for environmental liabilities are audited at least annually; other facilities are audited less frequently. The question of who performs the AMAX audits was settled in favor of the audit team being independent of personnel from the facility being surveyed. Other methods of auditing could be the following: - Independent contractor (Appendix A) - Combination of independent contractor and in-house staff - Self-audit by site personnel The merits and demerits of who should conduct the audit can be analyzed to suit your particular needs. Next you need to decide on the procedure for the audit and the form for reporting and follow up. Environmental publications referenced in Appendix B can be helpful to you at this point. After deciding on the form of auditing, a schedule is prepared and followed to the closest extent possible. This schedule should be published and distributed to the sites so facilities know when they are being audited. This is not designed to be "a game of hide and seek." Various elements of the AMAX Audit Program are as follows: Team selection Pre-visit preparation Site visit Exit interview Report Using the audit Follow-up Team Selection The usual make-up of the team is the audit manager, the environmental specialist who normally provides assistance to the site or has knowledge about the operation, and a legal representative if his or her schedule allows. The legal representative will review the findings of the audit team if a personal visit is not timely or necessary. Size of the team can be expanded, but a minimum of the audit manager and the environmental specialist is best. Two sets of observations are better than one. The environmental specialist can also provide the rapport which is beneficial to creating the appropriate tone so that the site people will be as cooperative as possible. This is not to be an antagonistic exercise.

Jan 1, 1991

By Samantha Smith

Nautilus is completing the world&apos;s first environmental impact assessment (EIA) of seafloor mineral extraction and Nautilus has gained extensive experience conducting environmental studies in subsea environments. Nautilus is currently working on the Solwara 1 Project in the Bismarck Sea, Papua New Guinea, where high grade seafloor massive sulfide deposits lie at ~1600 m water depth. Conducting an EIA in the deep sea presents some interesting and exciting challenges. Seafloor studies commenced in December 2005 using a remotely operated vehicle (ROV) fitted out with highly specialized scientific equipment to conduct water quality, sediment, biological and oceanographic studies. During 2007 and 2008, Nautilus launched two two 30-day ROV programs dedicated to environmental baseline studies and during this campaign, over 550 biological, sediment and water samples were collected and over 20,000 seafloor observations were logged. On board specialists included an international team of experts in the field of deep sea marine science. Collaboration between industry and scientific research institutions allows data to be collected for the EIA but also provides an extraordinary opportunity for researchers to access sites that might otherwise remain unobtainable to science. This presentation will review the studies conducted as part of this exciting project. Keywords: Seafloor Massive Sulfides, Environmental Impact Assessment

Jan 1, 2008

By Joseph G. Carleton

INTRODUCTION The increasing concern for the environment may well present far more opportunities than problems for those involved in all phases of tunneling. All too frequently in the past, environmentalists and their concerns have been cast in a negative light, as obstacles to be overcome. Often forgotten is the fact that these same environmental concerns have created a rapidly increasing demand for new tunnels. Tunnels for rapid transit projects, clean water supply, and sewage treatment have been given a boost because of environmentalists&apos; concerns about overuse of automobiles, inadequate water supplies, and improper sewage disposal. Concurrent with increasing use of tunnels to help solve or alleviate some of our environmental problems is an obligation not to create new ones in the process. Concerns which we feel responsible tunnel owners, engineers, and contractors should address themselves to include: (1) Minimum energy consumption, both during construction and in operation of the completed project; (2) proper storage and/or disposal of the excavated material; (3) minimum disruption during the construction process - noise, traffic, unnecessarily unsightly work areas, and possible weakening of foundations of nearby structures; and (4) a finished project consistent with community and environmental goals. We are especially concerned about two things. First, the longrun implications of a project -- what&apos;s good for a few people in the short-run may be bad for most of the people in the long-run. Cutting corners to save a little money now is false economy. Second, the fact that ultimately we all share the same earth -- its water, air,

Jan 1, 1974

By G. Falalakis

The Perama Hill gold project is an environmentally friendly project designed with the principle of zero discharge to the environment. The main issues of the proposed mine that are addressed in this paper are the water management, the dam and tailings management facility parameters as well as the mine closure plan, which demonstrate the sustainable design of the project. The water plant circuit will operate using 87% of recycled water and rainfalls, while the pumped aquifer is completely unsuitable for any other use. The proposed water management plan is based on different meteorological conditions for every month and optimizes the external water needs. The tailings pond area that is sited on intensely argilized rocks, will be composite-lined resulting in a permeability value of less than 10-10 m/s, and will exceed the safety parameters for maximum earthquake intensity, flood conditions and seepage. Tailings will contain less than 1 ppm cyanides (almost potable water ranges) and will be free of heavy metals (oxide ore material). The proposed rehabilitation plan comprises of decommissioning and demolition of the plant and auxiliary facilities, open pit partial back-filling and recontouring, appropriate capping of the tailings impoundment, revegetation, maintenance of area drainage system and monitoring for 5 years after rehabilitation. The plan is fullycosted, will be prepaid and through the agreed final land uses with the local community and the proposed actions of the corporate responsibility will attribute to the sustainable development of the area. The design of the Perama Hill project according to new EU and UN legislation and practices ensures that it will be the best example of gold mining operations in Greece.

Jan 1, 2008

By M. Yavuz

Multiple Criteria Decision Making (MCDM) is one of the most considerable branches of Operation Research. MCDM refers to making decisions in the presence of multiple, usually conflicting, criteria. The problems in MCDM are classified into two categories: Multiple Attribute Decision Making (MADM) and Multiple Objective Decision Making (MODM). However, very often the terms MADM and MCDM are used to mean the same class of models and mostly confused in practice. Usually, MADM is used when the model cannot state in mathematical equations and otherwise MODM is used (Hwang and Yoon, 1980). Decision-making (DM) is extremely important stage in Mining Engineering like other engineering branches. Every mining engineer makes several decisions in daily mining applications. Most of the decisions made by mining engineers are completely instinctive according to their past experiences and there is not any DM method applied in DM process. Analytic Hierarchy Process (AHP) is one of the well-known techniques solving the decision problems. The AHP is very simple, and understandable method especially non-numerical data considered in DM process. Equipment selection is one of the prominent problems of mining engineering. Mining engineers have to make difficult decisions when equipment selection stage. As the decisions in the equipment selection have radically influenced the economic life of any mining scenario, these are considered as complex MADM problem. So, the decision maker can evaluate the subjective criteria in the problem of equipment selection. The decision maker wants to maximize more than one objective criterion for equipment selection stage. Among the number of alternatives, the most suitable equipment must be selected according to objectives and alternatives. MADM applications can help the decision maker to reach the optimal solution for the equipment selection. In the mining industry, MADM methods can be applied for the equipment selection because it is a process that includes subjective and objective criteria affecting the selection of equipment among the alternatives.

Jan 1, 2007

By J. H. LaVerne Palmer, W. (Bill) C. Cox, Lorant B. Geller

An erector transporter (ET) has been designed and built to lift, carry and erect heavy machinery components, in particular the components of a 7.6 m diameter tunnel boring machine (TBM), within the access tunnels of a submarine coal mine in Eastern Canada. The ET is capable of manoeuvring within a 7.6 m tunnel while precisely positioning components as large as 6 m in diameter and weighing up to 27 tonnes each. The unit can negotiate 20% grades while carrying loads of 30 tonnes. The major design features, verification tests and performance trial results are presented. The versatility of the ET is such that many other applications are possible.

Jan 1, 1985

By A. Tsouchlaraki

The physical relief is a variable of utmost significance in the course of the analysis, evaluation, design and management of the visual environment. In this sense, there are cases where it would be desirable to isolate the relief from the other elements making up the visual environment and to investigate its visual value separately. Such cases include the technical works that cause major and permanent alterations to the relief, as well as the works, of which the spatial arrangement depends on the morphology of the ground. Slopes, distances, hypsometric difference values, viewsheds are elements of the relief that affect the visual value of a landscape, but also the ability of a particular landscape to accept and absorb new activities. This paper describes an evaluation and prediction model of the visual value of the landforms. A questionnaire survey takes place in order to investigate the public preference, using a sample of 221 persons in the broader area of Athens. The means used to demonstrate the various forms of reliefs are 32 perspective digital relief images. Following this and in order to investigate the elements of the relief that affect its visual value, 20 quantitative indices were developed and examined so as to select the best ones. Linear prediction models of the visual value were investigated from the previous elements, through a regression process. The applications of the proposed model in physical environment planning are many, such as the prediction of visual impact by arranging works that alter the relief of a region, as it happens in mining, metallurgical and waste disposal sites.

Jan 1, 2005