Search Documents

By M. H. Moys

I had the good fortune to attend the above Conference which was held in Kanpur, India, on 11-15 December, 1995. The Conference was held in honour of Professor P.C. Kapur of the Indian Institute of Technology in Kanpur. Professor Kapur was one of the early students of legendary teacher and researcher of mineral beneficiation, Professor Doug Fuerstenau of the Department of Materials Science and Engineering at the University of California at Berkeley. I have attended my fair share of international conferences and this one certainly rated at the top of the list on several counts. With an open-hearted hospitality which one might almost take for granted once you have spent some time in India, the organizers of the Conference looked after every need of their guests, including breakfast and transport to and from the conference centre, wonderful traditional lunches and dinners and outstanding entertainment in the evenings. The papers were generally of a high standard, and debate flowed enthusiastically and freely. Several international guests delivered seminal papers in their fields as discussed below.

Jan 1, 1996

The following notes have been compiled to assist authors in the preparation of papers for presentation to the Institute and for publication in the Journal. STANDARDS FOR ACCEPTANCE To merit consideration papers should be of sufficient high standard and contain matter that is new, interpretations that are novel or of new significance and conclusions that cast a fresh light on old ideas. Their publication should be of real interest to technical men and of benefit to mining and industry. Authors must realize that because a mine shaft is new or the mine itself is newly established, this in itself does not justify a paper unless significantly new techniques or processes were involved in the opening-up procedure. A few well selected diagrams and illustrations are often more pertinent than an amorphous mass of less well chosen material. Over-statement and dogmatism are jarring and have no place in technical writing. The amount of textbook material included in a contribution should be the minimum essential to the argument. The length of a paper is not the criterion of its worth and it should be as brief and concise as possible, consistent with the lucid presentation of the subject. Avoid the use of the first person, be objective and do not include irrelevant or extraneous matter. Papers should be submitted at least three months prior to the intended date of presentation. The text should be typewritten, double-spaced, on one side only of foolscap paper, leaving a left-hand margin of 11-inches, and should be submitted in duplicate to facilitate the work of the referees and editors. Galley proofs are sent to the authors for the correction of printers' errors and not for the purpose of making alterations and additions which may be expensive. Should an author make alterations which are considered excessive, he may be required to pay for them. ORTHODOX SEQUENCE Title and author's name together with author's degrees, titles and position Summary, abstract or synopsis Introduction Development of the main substance Conclusions References. Title: This should be as brief as possible, yet give a good idea of the subject and character of the paper. Style: Writing should conform to certain prescribed standards. The Institute is guided in its requirements by: Collins, F. H. Authors' & Printers' Dictionary-Oxford University Press. Hart, H. Rulesfor Compositors and Readers. Humphrey Milford (familiarily known as the Oxford Rules). Fowler, H. W. & F. G. The King's English-Oxford University Press. Generally: Avoid unnecessary use of capitals and hyphens, while punctuation should be used sparingly and be governed by the needs of sense and diction. Sentences should be short, uninvolved and unamiguous. Paragraphs should also be short and serve to separate basic ideas into compact groups. Quotation marks should be of the 'single' type for quotations and "double" for quoted matter within quotations. Interpretations in the text should be marked off by parenthesis ( ), whereas brackets [ ] are employed to enclose explanatory matter in the text. Words to be printed in italics should be underlined singly. For small capitals they are to be underlined DOUBLY and for large capitals TREBLY. Abbreviations and symbols are laid down in British Standard 1991 and proof correction symbols in British Standard 1219C. Abbreviations are the same for the singular and plural, e.g. ft for foot and feet, lb for pound and pounds. Percentages are written in the text as per cent; the symbol % is restricted to tables. Likewise ft and in. should be used, x' y" only being permissible in diagrams and plans. Drawings and diagrams are to be in black India ink and should be about 6 in. wide. Numbering of tables should be in Roman numerals: I, II, etc. and figures in Arabic numerals: Fig. 1, Fig. 2, etc. Photographs should be black and white glossy prints. As a guide to the printer the author should indicate by means of notes in the margin of the typescript where drawings and diagrams, etc. are to appear in the text. When submitting graphical representations avoid a fine grid if possible. Curves should be in heavy line to stand out. Lettering too should be bold as a reduction in size is often involved in the printing process. SUMMARY ABSTRACT OR SYNOPSIS It is most important that the summary should provide a clear outline of the contents of the paper, the results obtained and the author's conclusions. It should be written concisely and in normal rather than abbreviated English and should not exceed 250 words. While the emphasis is on brevity this should not be laboured to the extent of leaving out important matter or impairing intelligibility. Summaries simplify the task of abstractors and therefore should present a balanced and complete picture. It is preferable to use standard rather than proprietary terms. FOOTNOTESAND REFERENCES Footnotes should be resorted to only when they are indispensable. In the typescript they should appear immediately below the line to which they refer and not at the foot of the page. References should be indicated by super-script, thus . . .1 . . . 2. Do not use the word Bibliography. When authors cite publications of other societies or technical and trade journals, titles should be abbreviated in accordance with the standards adopted by this Journal.

By N. C. Joughin, A. C. Buckmaster

The use of face conveyors in gold mines by N. C. JOUGHIN. B.Sc. (Eng.). Ph.D. (Wits) (Member) and A. C. BUCKMASTER; M.A. (Cantab.) A mechanized stope-cleaning system has been developed around an armoured face conveyor, which was tested on the surface and in two underground trials. In the second underground trial, an average face advance of 8,5 m per month was obtained with a labour productivity of 27 ca/worker/month on a two-shift blast cycle. Two new face cleaning systems have been built, each incorporating an armoured face conveyor, a loading plough, a collapsible self-advancing barricade, and an integral roof-support system. These are about to be tested. A new type of reciprocating flight conveyor is being developed for stope use. This is cheaper, lighter, and more compact, and exhibits better wear characteristics, than an armoured face conveyor. In the early stages of the trials, this conveyor frequently achieved a singleshift blast cycle. It should be possible to achieve face advances of up to 40 ca/worker/month with a consistent one-shift blast cycle. The use of drill rigs and a self-advancing roof-support system would improve the productivity to over 50 ca/worker/month.

Jan 2, 1976

By M. Klapwijk

Ancient Metallurgy - In addition to the preceding three papers, the following three contributions were received for publication 1. An analysis of Bantu-made iron implements from the Letaba district M. KLAPWIJK INTRODUCTION It has often been stated that it is hardly possible in South Africa to classify Bantumade iron hoes according to their places of origin and manufacture. It is well known that these hoes were used for barter, and as currency in the purchase of livestock or the payment of lobolo, although reports of the value of the hoes differ widely. The difficulty in their classification has arisen from their distribution over a very wide area.

Jan 1, 1974

By John W. Harbaugh, Alfredo Prelate

The goal of the study described here is to develop objective. quantitative methods for estimating the outcome probabilities of exploratory oil wells. The study employs the 're-experience' approach, in which historical data are used in a manner which attempts to recreate the past. Our past experience, of course, is the principal guide to the future. To appraise present-day oil prospects, however, we must analyze prospects that have been drilled in terms of how these former prospects were interpreted before they were drilled. An analysis of how they are interpreted after they were drilled is an inadequate guide to the future because our hindsight knowledge is superior to our foresight knowledge. Objective calculation of future outcome probabilities, then, requires that we attempt to treat past information in a manner analogous to that in which we must treat present information in forecasting future outcomes.

Jan 1, 2014

By K. I. Afewu

A modified approach to the implementation of Gy?s sampling theory is discussed and used to design a procedure for sampling crushed gold ore feed to metallurgical process plants. The approach involves calibration of certain ore-specific parameters. These parameters were calibrated for two different crushed gold ores en route to grinding mills in process plants. The model predictions were compared with the predictions from Gy?s original model. Far smaller masses of samples are required by the modified model than by Gy?s model at the same relative variance. The representativeness of the sampling procedure if normally distributed errors are assumed was also calculated. These procedures and evaluations lead to significant savings on cost of handling and preparation of the samples and to a quantifiable degree of confidence in the analytical results for the process plant.

Jan 1, 1998

By F. T. Cawood

Inauguration of the new political dispensation in South Africa in 1994 initiated a dynamic shift in the ownership, management and development of the country’s affluent mineral heritage. The process of substituting the old South African regime with a new equitable system, started soon after the 1994 election of the African National Congress (ANC) to parliament. The Congress’ Freedom Charter revealed the intent of the new dispensation when it called for radical transformation of mineral development. However, since 1955 there have been important changes affecting the rules of mineral development. These are: •Firstly, a drastic change in politics ushered in by negotiation, a spirit of reconciliation and a desire to settle disputes peacefully •Secondly, the globalization of the South African mining industry in tandem with the opening of domestic mineral resources to foreign capitalists; and •Thirdly, the introduction of sustainable development as a holistic approach to mineral development in order to replace traditional narrow-minded environmental management. Each of these significantly shaped the new mineral investment environment of South Africa. This paper represents a summary of the historical developments leading to the current Mineral and Petroleum Resources Development Act No. 28 of 2002, its Regulations, the much-publicised Broad-Based Socio-Economic Empowerment Charter and its associated Scorecard.

Jan 1, 2003

By B. Larsen, S. Z. Nascimento, K. Fidje, J. P. M. Amaro, H. Gran

Safe and good operation of Søderberg electrodes is dependent upon high quality electrode paste coupled with correct electrode operating procedures. Good electrode performance depends further on proper melting and densification of the electrode paste. The melted paste should form a dense and viscous layer that prevents gasses from the baking process to move upwards. Both paste cylinders/blocks and briquettes can be used, but the procedures may differ between the various types of paste products. For briquette columns the formation of the important viscous layer is obtained through melting and densification of the briquettes. By basic rheological studies of electrode paste and by laboratory tests of briquette beds at isothermal conditions we have achieved a better understanding of the melting process. The effects of temperature gradients, pressure and friction between the briquettes and the electrode casing have also been evaluated qualitatively in pilot scale experiment and in industrial scale tests. The paper shows that melting and densification starts at a considerable lower temperature than the pitch softening temperature. It is concluded that the formation of a briquette electrode column depends on parameters as temperature, briquette column pressure and the friction. Operating conditions influencing the above parameters should be defined and established for each specific furnace operation. Such factors are e.g., charging and slipping procedures, column heating and electrical conditions.

Jan 1, 2004

By J. N. Van der Merwe

Following the Coalbrook disaster in 1960, research into coal pillar strength resulted in the adoption of the concept of a safety factor for the design of stable pillars in South African coal mining. At the time when the original statistical analysis was performed by Salamon and Munro in the early 1960s, 27 cases of failed pillar workings were considered suitable for inclusion in the database of failed pillars. Pillar failure did not stop after the introduction of the safety factor formula by Salamon and Munro (1967). In the ensuing years, pillars that were created before the application of the formula deteriorated and later failed, as did ones that were created after the introduction of the formula. This means that over time, the database of failed pillar cases increased in size, allowing ever more reliable analyses to be performed. The number of failed cases in the database had grown from the original 27 in the 1960s to 86 by 2011. All the failed cases are contained in the updated database. The database of stable pillars, which is also used in the derivation of strength formulae, has now been extended from 125 to 337 cases. The new database of intact pillar cases is more complete as it bridges the time gap between the Salamon and Munro (1967) and the Van der Merwe (2006) databases. The original requirements for inclusion into the database were satisfied in the compilation of this latest collection. The characteristics of the original database of intact pillars did not change in a meaningful way. The mining depth and pillar dimensions of the new database are largely as they were in the original database. Time-related trends with regard to pillar dimensions and depth of mining could not be found, indicating that the geometrical parameters of coal mining in South Africa have not changed meaningfully in approximately a century of mining. The characteristics of cases in the updated database of failed pillars does not differ substantially from the one published by Van der Merwe (2006). The same difference between that database and the original Salamon and Munro database, namely that the average safety factor of the failed cases had increased dramatically, from 1.0 to 1.5, is still apparent. This may be due to the inclusion of more failures from specific areas that exhibit a disproportionate number of failures at higher safety factors. These areas are the Vaal Basin, Klip River, and Free State coalfields. The new database confirms yet again that there is no correlation between the safety factors of failed pillars and their time of failure. The safety factor on its own is thus not a reliable predictor of longterm stability of pillars. Keywords coal pillar, stable pillar cases, pillar collapse, pillar data base.

Nov 1, 2013

By N. Sacks, N. B. S. Magagula, I. Botef

"Low-pressure cold gas dynamic spraying was used to deposit WC-4wt%Ni and WC-4wt%Ni-1wt%Mo coatings onto mild steel. Dense coatings with very low porosities were produced. No decarburization occurred during deposition and no deleterious phases were formed. The coatings were subjected to standardized material characterization tests, as well as slurry abrasion testing to assess their wear behaviour. The wear tests were conducted in synthetic minewater-silica slurries, while distilled watersilica slurries were used as a control. The hardness of the coatings, 512HV0.3 and 458HV0.3 for WC-4wt%Ni and WC-4wt%Ni-1wt%Mo respectively, are comparable to those achieved using high-temperature coating processes. The abrasion wear rates for both coatings were less than 5 mg/min and 10 mg/min in the distilled water-silica and synthetic mine water-silica slurries respectively. The approximately 50% increase in wear rate in the synthetic minewater slurry is attributed to a synergistic corrosive wear mechanism. The predominant wear mechanisms were identified as binder smearing and delamination, with carbide grain fracture and pull-out. IntroductionSlurry abrasion is a common phenomenon in mining operations, particularly in pipelines transporting, for example, sand-water slurries. This type of wear can cause pipeline fracture, shortened operational lifetimes, and impede pipeline efficiency. To reduce or limit abrasion, thermally sprayed tungsten-carbide-based coatings are often used as pipe linings (Kanchan et al., 2010). This is due to their attractive mechanical properties, which include high wear resistance, stiffness, hardness, compressive strength, and tensile strength. These properties are provided by the coating microstructure and composition, which is a blend of hard, wear-resistant tungsten carbide (WC) particles embedded in a fracture-tough metallic binder phase (Brookes, 1997). Cobalt (Co) is the most commonly used binder due to its excellent wetting of the WC phase and moderate mechanical properties; however, its application is limited to non-corrosive environments as it has a low corrosion and oxidation resistance (Andren, 2001). Nickel (Ni) may also be used as a binder, and has been shown to have superior oxidation and corrosion resistance, but in some applications may not have the required mechanical properties (Kim et al., 2006)."

Jan 1, 2016

By R. Kosmicki

Wet end components of centrifugal slurry pumps used in the hydraulic transport of solids are subject to substantial erosive wear. Accurate prediction of the casing wear rate and location for a particular duty is beneficial for correct pump selection and design, maintenance planning, and elimination of emergency shutdowns. CFD multiphase simulation using the Eulerian-Eulerian approach is being applied successfully to determine the velocity fields and solids concentration in the centrifugal pump, allowing for accurate predictions of casing wear patterns resulting from sliding abrasive wear. Simulation results for various single domain and multi-domain (multistage) multiphase simulations are discussed. Emphasis is placed on results from a 3-dimensional, multi-stage transient, multiphase simulation and comparison to field data.

Jan 1, 2007

By G. P. Dyke

With the removal of the majority of the shallow mineral reserves there has been an increase in the mining depths in the South African mining industry. This has, in turn, changed the industry?s and stakeholders? perceptions of risk associated with mining-induced instability. In recent years the increased mining depth, particularly in open pits, has led to an increase in pit slope failures, which has highlighted the need for appropriate and effective pit slope management programmes. Such a programme comprises many facets, including mine hazard plans, regular slope inspections, cleaning of interim and final pit faces, blasting practices, histories of failures, pit depressurization, stormwater control and evacuation procedures. However, it is arguably in the field of slope monitoring that the most significant strides have been made in terms of new technologies and best practice in open pit mining geotechnics, with the introduction of technologies such as laser scanners and slope stability radar. This paper seeks to illustrate the operational benefits associated with the implementation of new technologies into open pit mining, using AngloGold Ashanti?s Geita Gold Mine in Tanzania as an example.

Jan 1, 2009

By M .. Hori, H. Onishi, Y. Goda

The split-lining structure was newly developed for the air-tight lining of the underground compressed air storage cavern. This structure consists of separated reinforced concrete (RC) segments and air-tight membrane. It is most important for the Compressed Air Energy Storage Gas Turbine (CAES-G/T) system to develop the economical lining. In order to verify the applicability of split-lining structure, CAES-G/T pilot plant was constructed and operated for 6 months. We confirmed the practical usefulness and safety of this system through the operation. This paper presents the mechanical behaviour of surrounding rock mass and the lining structure observed through the operation of CAES-G/T pilot plant. Nous avons mis au point une structure de revêtement modulaire pour le revêtement des cavernes souterraines hermétiques à pression. Ce revêtement est composé de segments de béton armé et de membranes hermétiques. Il était très important, pour le CAES-G/T (Compressed Air Energy Storage Gas Turbine), de développer un revêtement économique. Afin de vérifier l’aptitude d’application de notre revêtement modulaire, nous avons construit un système pilote CAES-G/T et nous avons effectué des essais de fonctionnement pendant six mois. Ces essais nous ont permis de confirmer l’utilité et la sécurité du système. A travers le présent rapport, nous rendons compte de la structure de ce nouveau type de revêtement et du comportement mécanique de la masse rocheuse environnante que nous avons pu observer au cours desdits essais. Als luftdichter Druckbehälter wurde eine gegliederte Belagsstruktur für tief unterirdisch liegende Felshöhlungen entwickelt. Diese Struktur ist aus Stahlbetonabdeckung und luftdichter Plane aufgebaut. Bei der Entwicklung des Pressluftgasturbinen – Stromerzeugungssystems (CAES-G/T) war es die wichtigste Aufgabe, einen wirtschaftlichen Belag zu entwickeln. Deswegen wurde zum Nachweis der Effektivität der gegliederten Belagsstruktur eine Pilotanlage errichtet und 6 Monate lang betrieben. Durch den Betrieb konnten wir die Praktikabilität und Sicherheit des Systems bestätigen. Dieser Aufsatz ist ein Bericht über das Verhalten der durch Betrieb der CAES-G/T Pilotanlage beobachteten Belagsstruktur und umliegenden Felsmasse.

Jan 1, 2003

By Z-B. Cheng, X-J. Liu

"Intensive mining of shallow coal seams tends to result in severe subsidence of the ground surface. Surface subsidence is a complex dynamic spatiotemporal process that constantly changes as mining advances. With Liangshuijing coal mine as a case study, 3DEC numerical software was used to simulate the development of the moving subsidence field from open-off cut to full subsidence on the working face. The results demonstrate that the formation of a subsidence field is directly related to the coal seam depth H and the extent of the mine workings. Taking the advance distance of the working face as the unit of scale, the process of surface subsidence can be divided into four stages: micro-change (H/ p), the development of surface subsidence (2H/ p), the formation of a movement subsidence field (3H/ p), and dynamic balance (4H/ p). The changing movement of a subsidence field can be fully described by the characteristics of surface subsidence value, curve slope, and the inflection position. The results provide important technical support for predicting surface subsidence and the temporal–spatial evolution features of mining subsidence. IntroductionChina’s coal output was about 3.52 Gt in 2017 (China National Coal Association, 2018), making it the largest coal producer in the world, accounting for almost half of total world coal production. Coal production and distribution play a vital role in the energy industry of China. However, entire overlying strata, from coal seam to surface, are disturbed as a result of long-term, high-intensity and large-scale mining, causing surface subsidence. This results in groundwater loss, surface desertification, vegetation loss, and mud-rock flows. These issues have become topics of common concern throughout society. According to related research results (Liu 2008), the area of surface subsidence caused by coal mining in China has reached about 600 000 ha, some 0.2 ha (and up to 0.42 ha) of surface subsidence for every 10 000 t of coal produced. Surface subsidence disasters not only damage buildings, water conservancy, transportation infrastructure, and farmland, but also cause adverse effects on individual and community lifestyles, environmental hygiene, and economic development. Deterioration of the ecological environment in mining areas has a long history and is very harmful (Lu, 2015)."

Feb 1, 2019

By M. H. Solomon

After the global financial crisis of 2008, African mining is entering anew phase of development. The rapid withdrawal of emerging market funding from the critical exploration and development industries provided a hiatus in funding, a gap which was quickly filled by Chinese and other Asian investors. While the continent is still economically dependent on its extractive industries, the prevalence of Dutch Disease has undermined Africa?s ability to benefit fully from its mining, oil, and gas industries. While the extractive industries are closely related to many of the more fragile and failed states in Africa, it is equally true that the strongest states in Africa have mining-based economies. This paper explores the possible linkages between mining, strong and weak political economies, and poverty in Africa. It draws the conclusion that neither Dutch Disease nor Resource Course is a given in resource-endowed countries, and that it can be avoided if the mining economies in these countries are actively integrated into their respective broader economies and used to foster economic diversification. The author asserts that given the capacity constraints of many African governments, it is contingent on mining companies to become integrally involved in catalysing diversification around their infrastructure and supply chains.

Jan 1, 2011

The First International Symposium on Seismicity in Mines, organized by the South African National Group on Rock Mechanics in collaboration with the South African Institute of Mining and Metallurgy, was held in Randburg (near Johannesburg) from 13th to 17th September, 1982. It was the first attempt to provide an international forum for the consideration of seismic problems specifically affecting mines or associated with mining. Numerical mathematics The South African Society for Numerical Mathematics and the Computer Science Department of the University of Natal are organizing the Ninth Symposium on Numerical Mathematics to be held in Durban from 18th to 20th July, 1983.

Jan 1, 1983

By A. Bhattacherjee

The Shewhart [X]?and R charts are still the most popular control charts in use today for continuous monitoring of quality data. However, for these charts to function properly, the underlying assumption of normality and independence of data must be satisfied. When either independence and/or normality of data are not present, which is a common feature of ore quality data, an application of the conventional Shewhart [X]?and R charts may introduce false alarms in the analysis of the data. To address these issues, a guideline is proposed for construction of appropriate univariate and multivariate control charts for a variety of situations. A use of this guideline to a bauxite mine suggested the construction of special cause control chart for the analysis of individual variables namely, Al2O3% and SiO2%; whereas, the multivariate T2 chart based on residuals is proposed for the bivariate analysis of the variables. The case study clearly revealed that without considering the data correlation, one may be in a state of false impression about an out of control condition while using the Shewhart [X]?and R charts for univariate and the Hotelling T2chart for multivariate analysis. To compare the effectiveness of the control charts, specifically the Shewhart [X]?and the special cause control charts, a simulation study was conducted. It was found that the conventional Shewhart chart provided lower probability of coverage than the special cause control chart. It was also revealed that the quality specification of Al2O3% is met as the variation of Al2O3% is well within the specification limits; whereas, it is difficult to meet the quality specification of SiO2% on a regular basis.

Jan 1, 2002

By J. -W. Kim, Y. -B. Kang, H. -G. Lee

The effect of SiO2addition on the decomposition of Li2CO3was investigated at temperatures up to 1000ºC. It was found that addition of SiO2greatly enhanced the decomposition of Li2CO3. The main decomposition reaction started at around 600ºC, and completed just above the melting point of Li2CO3. The major decomposition product was Li2O?SiO2irrespective of the Li2CO3to SiO2mixing ratio while both reactants were available. It was ascertained that a liquid layer betweenLi2CO3and SiO2particles formed and facilitated the decomposition reaction. The governing reaction of the decomposition was the one between the dissolved Li2CO3and SiO2in the liquid layer to form Li2O?SiO2. The decomposition rate was independent of the Li2CO3/SiO2mixingratio until either one had been completely exhausted. When excess Li2CO3existed, it further reacted with the initial product of Li2O?SiO2to form 2Li2O?SiO2. When SiO2was found in excess, on the other hand, no further reaction took place. This is attributed to the fact that uponLi2CO3exhaustion there is no liquid phase available to facilitate further reaction. The apparent activation energy of the decomposition of Li2CO3in existence with SiO2is 198 kJ mol-1.

Jan 1, 2004

By T. Mahlangu Mahlangu, T. Fungene, K. C. Sole

"Although oxygen is widely employed as the oxidant of choice in gold leaching by cyanide, its low aqueous solubility presents some drawbacks in practical application; hydrogen peroxide has therefore been considered as a possible alternative. The aim of this investigation was to study the catalytic decomposition of hydrogen peroxide, which generates an oxidizing intermediate species, and to understand its effect on cyanide destruction. Operating conditions that facilitated the effective decomposition of hydrogen peroxide were established by varying the pH and catalyst type and concentration. The oxidizing intermediate, detected using an indirect technique, was found to be the hydroxyl radical (OH?). OH? is commonly generated in acidic solutions, but this work demonstrated that it is also produced at the alkaline pH values necessary for cyanide gold leaching. The effects of free and complexed iron and copper catalysts on the oxidation and consumption of hydrogen peroxide and cyanide were also investigated. It was shown that the cyano complexes of Fe(II) and Cu(I) are also effective as decomposition catalysts. Hydrogen peroxide concentrations above 0.01 M decreased the free cyanide concentration, which was attributed to the probable formation of the cyanate anion (CNO-). Although cyanide consumption increased due to its oxidation in the presence of OH?, excessive cyanide consumption in the presence of copper was attributed primarily to its complexation by the unstable copper(I) cyanide species. Rate constants for the decompositions of H2O2 and cyanide by ferrocyanide and copper cyanide were calculated; the latter was identified as being a better catalyst. IntroductionLeaching of gold from its ores using cyanide has been employed for well over a century (Habashi, 2016). Addition of cyanide converts the gold into a cyanide complex (Au(CN)2 -) that is soluble in water (Wang and Forssberg, 1990). The leaching reaction can be represented as Equation [1]:"

Dec 1, 2018

By S. Burks

This paper develops the themes explored by the authors at the Fourth International Platinum Conference,. Optimization techniques can be used to significantly increase the value of mining businesses by enabling better long-term planning decisions. Open pit and underground mine design, mine scheduling, cut-off grade and blending, stockpiling, and the linking of these to flexible elements of the metallurgical recovery processes are all evaluated together. Transport or sale of intermediate products and the requirements of the product metal markets can also be considered. Experience shows that net present value (NPV) can potentially be increased by 5-35 per cent or more, usually even before the expenditure of significant amounts of project capital. The case studies presented include: > An existing operation with multiple open pits and PGM concentrators linked to offsite downstream processing facilities, and with infrastructure constraints for which the scheduling of current operations and the potential for expansion were investigated > An existing operation with an integrated portfolio of mines, concentrators, smelter, and refinery, for which the various possible sources of ore for processing were prioritized to match the downstream process plant constraints and the product markets > An underground operation in Zimbabwe for which the optimum mining width was calculated and expansion plans were evaluated > An underground mine with many separate mining sections, for which a revised schedule was developed aiming to keep the shaft system and processing plant at capacity with the highest net value material available at any time throughout the life of mine. In the concluding section of the paper, a few brief notes are included suggesting how the strategic recommendations from enterprise optimization studies may be implemented by the owner's team.

Jan 1, 2013