Search Documents

Your Council has pleasure in submitting its report for the year ended 30th June, 1969. COUNCIL The following served as Office Bearers during the year under review: Messrs. R. C. J. Goode (President), J. K. E. Douglas and V. C. Robinson (Vice-Presidents), P. Lambooy (Immediate Past President) and D. G. Maxwell (Honorary Treasurer). Members of Council: Messrs R. J. Adamson, M. Barcza, F. P. Bath, Or J. M. Bereza, Or W. Bleloch, Messrs H. Britten, H. E. Cross, A. R. C. Fowler, A. E. Gilfillan, G. W. Holl, Prof D. D. Howat, Or J. P. Hugo, Messrs C. J. Irving, D. M. Jamieson, J. G. Kirchner, Prof J. de V. Lambrechts, Mr C. E. Mavrocordatos, Or J. T. McIntyre, Mr J. A. Nixon, Prof R. P. Plewman, Messrs J. F. Reid, H. Simon, C. G. Sowry, W. T. Stobart and P. W. J. van Rensburg. Ten Council meetings were held during the year with an average attendance of eighteen. FINANCE The annual accounts, which are attached to this report, show an excess of expenditure over income of R2,124, compared with an excess of income over expenditure of R4,218 last year. There are a number of reasons for this substantial change. There was a loss on realization of investments compared with a substantial surplus in recent years. The publication of the Journal once again resulted in a large loss in spite of a generous subvention of R2,000 from the Department of Cultural Affairs and other assistance amounting to R750. The revenue from sales of publications was down considerably. This is a figure which fluctuates considerably from year to year. The secretarial fee was considerably higher than previously. Due to pressure of work it was necessary for the Secretary to relinquish his duties with the Institute of Land Surveyors and, therefore, for this Institute to assume the additional staff costs involved. Finally there was unusual expenditure on the 75th Anniversary celebrations. There was a pleasing increase in revenue from subscriptions, due to the steadily increasing membership, but this was quite inadequate to cover the substantial increases in expenditure and losses in revenue mentioned above. The changes that have been effected in the arrangements for the publication of the Journal have been mentioned elsewhere in this report. It is expected that these will bring about substantial financial benefits in the long term. The MacArthur Forrest Memorial Fund shows an excess of income over expenditure of Rl00 and the total fund was therefore increased by this amount to R4,206. The balance sheet indicates that the market value of quoted shares and debentures increased during the year from R8,755 to R13,059, while the Accumulated Funds now amount to R22,567 as against R24,691 last year. MEMBERSHIP Fifty-six Members, fifty-five Associate Members, thirteen Graduates, twenty-two Affiliates and twenty- nine Students were elected during the year. Twelve Members were admitted to Life Membership; seven Associate Members were transferred to the grade of Member; four Graduates and two Students were transferred to the grade of Associate Member; five Students were transferred to the grade of Graduate; three Affiliates were transferred to the grade of Member; five Affiliates were transferred to the grade of Associate Member. Three Members, seven Associate Members, two Graduates, two Affiliates and six Students were removed from the Membership Roll in terms of By-Law 7.7.1. Your Council records with deep regret the death during the year of the following members: E. F. J. Bulman (Member), E. F. Chapin (Member), R. A. H. Flugge-de-Smidt (Hon. Life Member), T. S. Haldane (Member), J. M. Massie (Associate Member), S. W. Page (Student), S. R. Rabson (Member), M. Ramsay (Member), F. Wartenweiler (Hon. Life Member). A comparative statement of the membership as at 30th June, 1969, and the end of the previous year is shown in the following tabulation: 30th June 30th June 1968 1968 Honorary Life Members 12 10 Honorary Members 6 6 Life Members 176 189 Members 488 514 Associate Members 409 448 Graduates 60 68 Affiliates153 155 Students152 162 1,456 1,552 PAPERS AND JOURNAL The Institute is changing the format of the Journal from the present size to the standard international A4 size with effect from August, 1969. In making this change it will conform to more general practice today in regard to publications and this should effect certain economies and facilitate selling of advertising space. It has been arranged that in future the publication of the Journal, including advertisement sales, will be handled by Kelvin Publications (Pty.) Ltd. who are already doing this work satisfactorily for the Mechanical and Electrical Engineering Institutes. In making these changes the opportunity was taken of redesigning the outer cover of the Journal to incorporate the new coat of arms. The Presidential Address by Mr R. C. J. Goode and twelve papers which were published in the Journal during the year are listed below: August, 1968: Presidential Address: "The Institute-In retrospect and prospect." September, 1968: "Rotary mill liner practice in the South African gold mining industry," by J. H. French and O. E. Lissner.

By J. N. Van der Merwe

The results of over 900 coal strength tests done during the period 1993?1994 for the SIMRAC project COL021A were re-analysed with a view to find a method to delineate areas or seams that can be grouped together for analyses of coal strength and strength decay characteristics. It was confirmed that the strength of a coal specimen increases linearly with increasing diameter-to-length ratio and decreases exponentially with increasing size of specimen. However, by extrapolation of the data, it was shown that beyond a diameter of approximately 2 m, the size effect is insignificant. For larger specimens, the diameter-to-length ratio (referred to as the width-to-height ratio for full scale mine pillars) alone continues to influence the strength. The slope of the linear strength vs. diameter-to-length ratio relationship is independent of the size of the specimen and is not unique for coals from different mines. However, the intercept of that relationship is unique and is a function of specimen size. This offers a previously unknown method to distinguish between the coals from different mining areas and coal seams. Ranked from weakest to strongest, the samples tested from the different mines are in the order shown below, which roughly corresponds to the judgement of practising rock engineers in the field: ?Sigma ?ZAC ?Goedehoop ?Kriel ?Bank ?Blinkpan ?Secunda ?Greenside Arnot ?Khutala ?Delmas

Jan 1, 2003

By S. L. Miller

The development of a pilot gold geostatistical ore reserve system proved that geostatistical methods worked well for the routine production of annual ore reserves on gold mines of the Gold Fields of South Africa (GFSA) group, and that the techniques could also be practically implemented, understood and accepted by Survey Department personnel. Many side benefits of the pilot system became apparent, and a variety of useful management information was provided by manipulating the data values that were already captured. It was decided that it was a priority computing project to develop a standard production system (GORS) for routine use by all the GFSA gold mines. Experience with the pilot system enabled detailed functional specifications for GORS to be laid down. These, together with group computing policy determined the terms of reference and constraints for the GORS development. System design could not be finalized until new and appropriate mainframe database software and graphics workstation equipment and software had been found. With these in place the basic system was structured to take best ad- vantage of the interactive features of the workstation, the number-crunching power of the mainframe and the flexibility offered by a relational database and associated 4GL tools. Application sub-systems were developed for data capture, statistical applications, geostatistical calculations, contour plotting and graphical queries. GORS is being introduced to the mines in a phased manner with suitable documentation, training and support structures to enable it to be routinely and effectively used on a day-to-day basis by all group gold mines.

Jan 1, 1987

By H. E. Parkinson, Y. P. Chugh

About 90 percent of the coal mined underground in the U.S.A. today is mined by the room-and-pillar system. The productivity of the system dropped from about 14,1t per man-day in 1969 to about 7,3 t per man-day in 1978. Since 1974, the U.S. Department of Energy (formerly the U.S. Bureau of Mines) has been engaged in research to improve the production and productivity of the room-and-pillar system. The effort involves the development of integrated, automated, and remote-controlled equipment and systems including remote-controlled continuous miners, automated miner-bolters, automated extraction systems, continuous haulage systems for use behind miners, and remote-controlled equipment for miners, bolters, and shuttle cars. These systems are discussed briefly, the discussion being related primarily to coal winning, although the concepts could be utilized in room-and-pillar systems in mines other than coal mines.

Jan 1, 1981

By W. U. Reimold, R. Armstrong, R. G. Charlesworth

For many years rockbursts have plagued the mining industry. Although much research has gone into studying this phenomenon only a small proportion of it has been on the actual source mechanism. A study was recently carried out to compliment the previous work done on the micro-structure of these features and to compare it to the micro-structures seen on shatter cones, from meteorite impacts. Both optical and electron-microscopy were used during the study. Samples were collected from rockburst sites by the CSIR Miningtek Rockburst Investigation Unit, and from the collar of the Vredefort Impact Crater. In the optical-microscopy study, the pinnate fractures observed in previous studies were seen in the shatter cones, through all the material. In the rockburst samples, the fractures were observed only in the quartz grains. Quartz micro-crystals were present in the rockburst samples and appeared to be the product of comminution rather than crystallisation. Cataclasite was present on rockburst and shatter cone fracture surfaces. The observations of the shatter cone surfaces with the scanning electron microscope are in agreement with previous work, including the observed presence of melt features, spherules and spheroidal material. The deformation in the rockburst samples is concentrated in the quartz grains, highly complicated with brittle features like sub-conchoidal structures and step structures present. A quartz spherule was identified on one rockburst sample and rhombic-dodecahedra type micro-crystals were present and seen fracturing off quartz grains. It is clear that the rockburst and shatter cone fracture surfaces are quite different; the shatter cone deformation is equally distributed across the sample and involves plastic-deformation, while the deformation in the rockburst material is concentrated in the quartz grains and, with the exception of spherule formation, is brittle. This study agreed with the current explanation for the formation of the rhombic-dodecahedra, and disproved the possibility of it being coesite or fine-grained meta-chert. Although there is no definite evidence of the mechanism of formation of the spherule, it is believed to be the product of vaporization and condensation, and the presence of this material indicates the extreme conditions under which this event occurred.

Jan 1, 2003

By H. Tveit, E. H. Myrhaug, J. K. Tuset

Silicon metal as a commodity material is produced by carbothermic reduction of quartz in electric submerged arc furnaces, where CO2 forms as a by-product. Since 1997 the Norwegian Ferroalloy Producers Association have been engaged in research programmes aiming for reduced CO2-emissions associated with fossil carbon in their processes. One important issue has been to study how charcoal and wood chips perform compared to coal and coke in the silicon process. The ability of the carbon-rich reduction materials to react with SiO-gas is commonly assumed to be of large importance to the performance of the process. Based on laboratory experiments with different carbon materials, combined with estimation of parameters in a mathematical model of the reaction between carbon and SiO-gas, a foundation for a theoretical study of the performance of the carbon materials in a silicon furnace is established.

Jan 1, 2004

By J. N. Van der Merwe

The principal goal of the research described in the paper was to determine, by measurement of pillar scaling on pillars that have not failed, whether the pillar life prediction method developed by van der Merwe (2003) was valid as it stood or whether adjustments were necessary to the rates indirectly derived from observation of failed pillars. To this end, measurements were taken on over 350 pillars at 13sites on 6 mines. The project was done as a collaborative effort between the University of Pretoria, the Nancy School of Mines and CSIR Miningtek. During the course of the investigation, it was found that the majority of pillars display maximum scaling at mid height, that there was no clear preferential direction of pillar scaling, and that pillar corners do not scale significantly more than the mid pillar areas. The most important conclusion was that the scaling rates found by measurement agreed with the inferred rates found in the previous work. The previously developed procedure for the prediction of pillar life spans consequently requires no adjustment, although the error span is in the region of 20%. It is recommended to do further research into the effect of sealing of panels and, possible chemical changes taking place in the pillars as they age on the scaling rate.

Jan 1, 2004

By F. T. Cawood

Monitoring of the slopes of surface mines can prevent loss of life, loss of equipment, loss of production and possibly the loss of the mine. The effectiveness of such monitoring depends on the extent to which slopes give adequate advanced warning before failing, and on the ability of the monitoring system to detect such warning. In this paper an overview is given of slope monitoring requirements, from both the geotechnical and survey points of view, as well as the types of equipment and instrumentation that are available. Legal issues relevant to slope monitoring are also dealt with. It is concluded that conventional geotechnical and survey instrumentation will continue to have their place in slope monitoring. However, the slope monitoring scene has changed substantially in recent years. A real and volume-based monitoring equipment is now available and this has provided, and will continue to provide, the means to improve safety, and to enhance productivity in mining. Its benefit to slope management is substantial. In the near future it is expected that data obtained from such equipment will add a much needed new dimension to slope engineering, and be used to improve slope designs and to optimize slope angles.

Jan 1, 2006

By F. L. D. Cloete

The following discussion relates to the paper by G. S. Hansford, C. D. Levy, and J. W. de Kock that appeared in the March 1976 issue of the Journal (vol. 76, no. 8, pp. 363-369) Competition for student members Each year the South African Institute of Mining and Metallurgy offers a prize (or prizes should the entries warrant it) of up to RI00 for the best paper or dissertation on a topic appropriate to the interests of the Institute. Engineering in South West Africa The SW A Engineering Profession Steering Committee was established on 4th April, 1977, its purpose being to formulate an Act covering the engineering profession in South West Africa.

Jan 1, 1978

By H. F. Niemand, C. J. Postma, P. L. Crouse

"SynopsisThe separation of zirconium and hafnium is essential in the nuclear industry, since zirconium alloys for this application require hafnium concentrations of less than 100 ppm. The separation is, however, very difficult due to the numerous similarities in the chemical and physical properties of these two elements.Traditional methods for separation of zirconium and hafnium rely predominantly on wet chemical techniques, e.g. solvent extraction. In contrast to the traditional aqueous chloride systems, the AMI zirconium metal process developed by Necsa focuses on dry fluoride-based processes. Dry processes have the advantage of producing much less hazardous chemical waste.In the proposed AMI process, separation is effected by selective sublimation of the two tetrafluorides in an inert atmosphere under controlled conditions, and subsequent selective desublimation. Estimates are made for the sublimation rates of the two tetrafluorides based on the equilibrium vapour pressures. A sublimation model, based on the sublimation rates, was developed to determine if the concept of separation by sublimation and subsequent desublimation is theoretically possible.IntroductionZirconium requires several purification steps to conform to nuclear-grade specifications. Little information is available on the sublimation separation of Zr and Hf compounds, especially in the fluoride form, the majority of which deals with sublimation under vacuum conditions. On the industrial scale, only vacuum sublimation of ZrF4 has been reported. No records were found for the sublimation of ZrF4 in an inert atmosphere. Information on the sublimation rate of ZrF4 or HfF4 in an inert atmosphere is also limited. The rate is assumed to be dependent on several factors, of which temperature, area, and composition are considered the most important."

Jan 1, 2015

Following a short review of selected literature, a back analysis of stress measurements of stress regeneration in a closed mini-longwall is shown. The agreement is good, lending confidence to the parameters used in the proposed numerical model. Foundation yielding was modelled in the absence of total stope closure. A ?Prandtl? wedge was formed, coinciding with the yield point of the pillar/foundation system. Some theoretical work is used as a starting point for the formulation of a new design methodology for strike or dip stabilizing pillar/foundation systems in deep level goldmines. The existing guideline for the stability of foundations (APS< 2.5UCS) is critically examined. Finally, the advantages of the new approach, and the work required to substantiate the proposed new design methodology, are outlined.

Jan 1, 1998

By H. M. Stewart, N. F. Dawson, J. P. Beukes, P. G. van Zyl, Q. P. Campbell, A. Jordaan, R. I. Glastonbury, L. N. Sadiki

"SynopsisThe physical properties of oxidative sintered pellets produced from typical South African UG2 ore are compared with the physical properties of pellets produced with conventional South African metallurgical-grade chromite ore (from the Lower Group 6 or the Middle Group 1 and 2 seams). A statistical evaluation of the cured (sintered) compressive strengths proved that pellets prepared from UG2 ore are likely to have the same, or better, compressive strength than pellets prepared from metallurgical-grade chromite ore. The cured abrasion strength of the UG2 pellets was also superior to that of the metallurgical-grade pellets. Scanning electron microscopy (SEM) backscatter, secondary electron, and elemental X-ray mapping were used to determine the reasons for the general superior strength of the UG2 pellets. The case study UG2 ore also required 13 kWh/t less energy for milling to attain the required particle size distribution prior to pelletization, which can lead to substantial cost savings. Results presented in this paper can be utilized by ferrochromium (FeCr) producers to better quantify the advantages and disadvantages associated with the use of UG2 ore for FeCr production.IntroductionChromite, a mineral of the spinel group, is the only commercially viable source of virgin chromium units. Geologically, commercial chromite deposits in the world are found in three forms, i.e. alluvial-, podiform-, and stratiform-type deposits (Murthy et al., 2011; Cramer et al., 2004). Alluvial deposits were formed by weathering of chromite-bearing rock with the subsequent release of chromite and gravity concentration by flowing water. However, these deposits are relatively small and of comparatively minor commercial interest. Podiform-type chromite deposits usually occur as irregularly shaped pods or lenses, and their distribution within a mineralized zone is usually relatively erratic and unpredictable, making the exploration of these deposits difficult and costly (Cramer et al., 2004). Stratiform-type chromite deposits occur as parallel seams in large, layered igneous rock complexes with more regular layering and lateral continuity (Cramer et al., 2004). The largest example of a stratiformtype chromite deposit is the Bushveld Complex (BC) in South Africa, which holds an estimated three-quarters of the world’s viable chromite ore resources (Cramer et al., 2004).Several chromite seams exist in the BC. The seams of economic interest are the Lower Group 6 (LG6), the Middle Group 1 and 2 (MG1 and 2), and the Upper Group 2 (UG2) seams (Cramer et al., 2004). The LG and MG seams are specifically exploited for their chromium content, while the UG2 seam is mined primarily as a source of platinum group minerals (PGMs) (Xiao and Laplante 2004). Extraction of the PGMs from the UG2 ore usually involves the liberation of the sulphide by milling and subsequent recovery of the PGM concentrate through flotation (Xiao and Laplante, 2004). Chromite in the PGM concentrate is undesirable; therefore, PGM recovery circuits are specifically designed to ensure maximum rejection of the chromite to the tailings stream. However, the chromite in the PGM tailings can potentially serve as feedstock for ferrochrome (FeCr) production, after beneficiation to increase the chromium content."

Jan 1, 2015

By J. T. Nel

The establishment of a pilot plant for the continuous production of titania pigment and nano-titania is discussed. The plant was designed, constructed and operated on the Necsa site. The TiO2 production capacity is 7?10 kg.h-1 by the reaction of TiCl4 and O2at>1000°C. Liquid TiCl4 is sprayed under pressure into a plasma reactor where it evaporates and reacts with O2 to form TiO2. Process optimization has allowed for continuous production without any clogging or blockages. The primary advantage of the plasma-assisted process is the possibility to recover and recycle the chlorine values in high yield as Cl2 for use in the manufacture of TiCl4. The HCl formed in most conventional fossil-fuelled processes makes Cl2 recovery and recycling much more difficult. Particle size distribution analysis of the fine, white product revealed a d50= 125 nm. The raw product consisted of 60% rutile that could be increased to 80?100% rutile by post-annealing. The specific surface area (SSA) of the pigment was 8?20 m2?g-1(BET). According to the CIE colour index the ?whiteness? (L*>95) of the plasma-produced pigment was better than that of several commercially available pigments. The particle size could be manipulated by controlling the TiCl4 feed rate, gas flowrates, and the particle quench rate and residence time. Nano-sized TiO2 powders with a particles size (d50) as small as 50 nm were also successfully produced in this way.

Jan 1, 2010

By M. Yavuz

One of the challenging problems for optimization in mining operations is to choose the best equipment among the alternatives. Equipment selection is an important task for mine management due to its operational cost, and is also an integral part of mine planning and design. Equipment selection is not a well-defined process because it involves the interaction of several subjective factors or criteria. Besides, decisions are often complicated and may even embody contradictions. Therefore, equipment selection is considered as a multi-criteria decision-making process, and suitable decision-making methods should be employed in this process. In this study, the loader selection for Aegean Lignite Colliery was made by using both the analytic hierarchy process and Yager’s method. Owing to the misusage of Yager’s method in the past, a new procedure is proposed in this paper for making proper decisions. It is highly recommended in this purposed method that criteria or alternatives should be grouped so as not to exceed the limitations of human performance (nine criteria/alternatives). The most appropriate solution for the loader selection was investigated by obeying this limitation for each method, and the results were compared. At the end of the decision-making process, a sensitivity analysis was applied for each method in order to see how a criterion affects the final decision. The advantages and disadvantages encountered during the application of each decision-making method are presented.

Jan 1, 2015

By P. J. Barton, N. F. Peverett

A brief review of the development and ultimate design of the Model 16 Photometric Sorter is given, including the differences between it and its predecessor, the Model 13, which is currently in operation at Doornfontein. A description of the West Driefontein sorting plant is given, together with the rationale of its design. The installation programme for the sorters is described, and current operating and maintenance procedures are discussed. Operating results are tabulated and compared with the original test results. Operating costs are also discussed.

Jan 1, 1980

By A. S. Macfarlane

Western Deep Levels (North) is a deeplevel, longwall gold mine. Severe strata control problems and high rates of elastic closure, resulting in high rates of energy release, are associated with mining at depths of up to 3 500 metres. To assist in controlling these aspects of mine design and safety, a waste backfilling system has been designed and commissioned. The integration of such a system into an existing, producing longwall brings many problems of logistics, organization, planning and control. It is the purpose of this paper to examine these aspects of fill management, and to describe some of the practical problems involved with the integration of this project into the mining environment. Although many of the rock mechanics and soil mechanics aspects of backfilling systems are common there are specific problems involved which apply to longwall systems. Very strict guidelines are required for planning personnel to design their backfilling systems for a particular situation. These aspects are examined, and basic models developed which can be used without the necessity of comprehensive input from rock mechanics. A summary of the financial implications is included, and these are examined with regard to possible future applications and expansion of waste filling.

Jan 1, 1988

By S. Mohanta, B. C. Melkap

"SynopsisDry beneficiation of coal by air dense medium fluidized bed is an emerging trend. It is widely believed that the particle size of the medium has a significant effect on the separation efficiency. This investigation demonstrates that medium particle size has a major effect on separation efficiency. Experimental results show that different size fractions of the same feed respond differently to the same size fraction of medium solids. Furthermore, a particular size fraction of feed coal responds differently with different size fractions of medium solids. The Ep values and overall metallurgical performance parameters, obtained from experimental results, clearly indicate the superior performance of an air dense medium fluidized bed separator when using –150+106 µm magnetite powder as the fluidizing medium. These observations reinforce the importance of sizing the medium particle size for the air dense medium fluidized bed.IntroductionIn an air dense medium fluidized bed (ADMFB), a fluidizing bed of a particular density is created by suspending solid particles in an upward air flow. A feed containing coal particles of different densities is introduced into this fluidizing bed. The particles with relative density less than the bed density float on the top of the bed, while particles denser than the bed density sink through it. Since there is a general correlation between ash content and density of coal particles, it is possible to remove ash-forming impurities from a raw coal to the required level by regulating the density of the fluidizing bed. Recently, the ADMFB process has received significant attention world-wide for its specific advantages of low operating cost and less restrictive for small capacities (Luo and Chen, 2001; Houwelingen and de Jong, 2004; Dwari and Hanumantha Rao, 2007; Sahu et al., 2009; Mohanta et al., 2012). This process is not recognized as a well-established industrial practice because of the availability of efficient wet processing technology. However, with the revival of interest in dry beneficiation of coal in general, and ADMFB in particular, there is a concerted effort to improve the efficiency of the ADMFB process, and successive improvements have made the process a competitive and viable option for beneficiating coal."

Jan 1, 2015

By E. Pardo-Igúzquiza, R. A. Olea

The bootstrap is a computer-intensive resampling method for estimating the uncertainty of complex statistical models. We expand on an application of the bootstrap for inferring semivariogram parameters and their uncertainty. The model fitted to the median of the bootstrap distribution of the experimental semivariogram is proposed as an estimator of the semivariogram. The proposed application is not restricted to normal data and the estimator is resistant to outliers. Improvements are more significant for data-sets with less than 100 observations, which are those for which semivariogram model inference is the most difficult. The application is illustrated by using it to characterize a synthetic random field for which the true semivariogram type and parameters are known.

Jan 1, 2015

By E. Wroth, D. G. Krige

Written contribution E. Wroth* (Visitor): The technical aspects of the assistance scheme which IS provided for in the Gold Mines Assistance Act, 1968, and certain consequential amendments to the Income Tax Act, 1962, are explained by Dr Krige. The object of this contribution is to explain the working of the Gold Mines Assistance Act (hereafter referred to as the &apos;Assistance Act&apos;) for the benefit of those concerned with the tax and assistance assessments of gold mining companies. The views expressed do not necessarily reflect the Revenue Department&apos;s interpretation of the legal provisions involved. 1. MINES WHICH QUALIFY FOR ASSISTANCE 1.1 The assistance scheme is applied on a selective basis. Mines which qualify for assistance are defined in the Assistance Act as &apos;assisted gold mines&apos;. The requirements for classification as an assisted gold mine are that: (i) the mine be a producing gold mine; (ii) it would be likely to close down within eight years if not assisted; and (iii) with State assistance its life would be appreciably prolonged and there would be a significant increase in production of gold or uranium, or of both gold and uranium. 1.2 A mine is only considered for classification as an assisted gold mine on application. Such applications must be made to the Mining Leases Board through the Government Mining Engineer. Classification of a mine as an assisted gold mine is at the discretion of the Minister of Mines who acts in consultation with the Minister of Finance and has regard to the recommendations of the Mining Leases Board. 1.3 The Minister of Mines will impose conditions subject to which a mine is to be classified as an assisted gold mine. The most important will be that the mine must immediately lower its operating pay limit, as normally calculated, by a percentage fixed by the Mining Leases Board and conduct its future mining operations in accordance with the average grade of its ore reserves determined on the basis of such lower pay limit. l.4 The Minister will fix the date as from which classification as an assisted gold mine is to be effective. So long as the mine has operated on the basis of the lowered pay limit for at least three months during the particular year of assessment, he would normally fix the effective date as the first day of the year of assessment.

Jan 5, 1968

By N. Snyders, I. Mwandawande, S. M. Bradshaw, M. Karimi

"Computational fluid dynamics (CFD) was applied to predict the average gas holdup and the axial gas holdup variation in a 13.5 m high cylindrical column 0.91 m diameter. The column was operating in batch mode. A Eulerian-Eulerian multiphase approach with appropriate interphase momentum exchange terms was applied to simulate the gas-liquid flow inside the column. Turbulence in the continuous phase was modelled using the k-_ realizable turbulence model. The predicted average gas holdup values were in good agreement with experimental data. The axial gas holdup prediction was generally good for the middle and top parts of the column, but was over-predicted for the bottom part of the column. Bubble velocity profiles were observed in which the axial velocity of the air bubbles decreased with height in the column. This may be related to the upward increase in gas holdup in the column. Simulations were also conducted to compare the gas holdup predicted with the universal, the Schiller-Naumann, and the Morsi-Alexander drag models. The gas holdup predictions for the three drag models were not significantly different. IntroductionColumn flotation is an important concentration technology that is used in the mineral processing and coal beneficiation industries. The growing interest in the use of column flotation in mineral processing has been attributed to the simpler flotation circuits and improved metallurgical performance compared to conventional flotation cells (Finch and Dobby, 1990). Flotation columns have also found other applications outside mineral processing, such as de-inking of recycled paper (Finch and Hardie, 1999).In column flotation, a rising swarm of air bubbles generated by means of air spargers is employed to collect the valuable mineral particles and separate them from the gangue minerals in a countercurrent process. Wash water, which is continuously fed at the top of the column, is used to eliminate entrained particles and stabilize the froth. The column volume can be divided into two sections – the collection zone in which the bubbles collect the floatable mineral particles, and the cleaning zone (or froth zone) where product upgrading is enhanced through the removal of unwanted particles entrained in the water mixed with bubbles from the collection zone."

Jan 1, 2019